Benutzeranleitung / Produktwartung ST200FP0001 des Produzenten Seagate
Zur Seite of 41
Product Manual Seagate ® 600 Pro SSD 100727924 Rev. A May 2013 Standard 2.5” Managed Life models ST480FP0001 ST400FP0001 ST240FP0001 ST200FP0001 ST120FP0001 ST100FP0001 Standard 2.
© 2013 Seagate Technology LLC. All rights reserved. Publication number: 100727924, Rev. A May 2013 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries.
ii Seagate 600 Pro SSD Product Manual, Rev. A Contents Seagate® Technology Support Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.0 Introduction . . . . . . . . . . . . . . . . . . . . .
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A III F IGURES Figure 1. Typical 5V Startup and Operation Current Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 2. Attaching SATA cabling . . . . . . . . . . . . .
Seagate 600 Pro SSD Product Manual, Rev. A 1 For information regarding online support and services, visit http://www.seagate.com/about/contact-us/technical-support/ Available services include: • Pre.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 2 1.0 I NTRODUCTION This manual describes the functional, mechanical and interface specifications for the following Seagate ® 600 Pro SSD model drives: These drives provide the following key features: • Multi-Level Cell (MLC) NAND Flash storage.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 3 2.0 D RIVE SPECIFICATIONS Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 4 [1] One GB equals one billion bytes when referring to drive capacity. Accessible capacity may vary depending on operating environment and formatting. [2] Max time approximately 30 sec when standby immediate was not issued before power down.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 5 2.4 P ERFORMANCE , R ECORDING AND INTERFACE TECHNOLOGY 2.4.1 Interface technology 480GB MODELS 400GB MODELS 240GB MODELS 200GB MODELS 120GB MODELS 100GB MODELS Interface Serial ATA (SATA-II) Interface Speeds Supported 6Gb/s, 3Gb/s, 1.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 6 When evaluating performance of SSD devices, it is recommended to measure performance of the device in a method that resembles the targeted application using real world data and workloads. Test time should also be adequately large to ensure that sustainable metrics and measures are obtained.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 7 2.8 P OWER SPECIFICATIONS The drive receives DC power (+5V) through a native SATA power connector. See Figure 2 on page 19. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 8 Table 3 400GB DC power requirements Parameter ST400FP00x1 (6.0Gb) Voltage +5V Power Regulation +/- 5% (watts) Average Idle Current 0.45 2.27 Average Sleep Current 0.10 0.52 Maximum Start Current DC (Peak DC) 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 9 Table 4 240GB DC power requirements Parameter ST240FP00x1 (6.0Gb) Voltage +5V Power Regulation +/- 5% (watts) Average Idle Current 0.47 2.37 Average Sleep Current 0.10 0.49 Maximum Start Current DC (Peak DC) 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 10 Table 5 200GB DC power requirements Parameter ST200FP00x1 (6.0Gb) Voltage +5V Power Regulation +/- 5% (watts) Average Idle Current 0.45 2.25 Average Sleep Current 0.09 0.47 Maximum Start Current DC (Peak DC) 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 11 Table 6 120GB DC power requirements Parameter ST120FP00x1 (6.0Gb) Voltage +5V Power Regulation +/- 5% (watts) Average Idle Current 0.45 2.24 Average Sleep Current 0.09 0.46 Maximum Start Current DC (Peak DC) 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 12 Table 7 100GB DC power requirements Parameter ST100FP00x1 (6.0Gb) Voltage +5V Power Regulation +/- 5% (watts) Average Idle Current 0.42 2.10 Average Sleep Current 0.09 0.46 Maximum Start Current DC (Peak DC) 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 13 2.8.2.1 Typical current profiles Figure 1. Typical 5V Startup and Operation Current Profile.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 14 2.9 E NVIRONMENTAL SPECIFICATIONS 2.9.1 Temperature Temperature is defined as the drive's internal temperature as reported by SMART attribute 194 for operation or the drive case temperature for non-operating.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 15 2.9.6.1 Operating vibration The maximum random vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. This sp ecification does not cover connection issues that may result from testing at this level.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 16 2.11 R ELIABILITY 2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) The product shall achieve an Annualized Failure Rate - AFR - of 0.58%. AFR and MTBF are population statistics that are not relevant to individual units.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 17 2.12 A GENCY CERTIFICATION 2.12.1 Safety certification These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so marked as to the certify agency.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 18 2.13 E NVIRONMENTAL PROTECTION Seagate designs its products to meet environmental protection requirements worldwide, including regulations restricting certain chemical substances.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 19 3.0 C ONFIGURING AND MOUNTING THE DRIVE This section contains the specifications and instructions for configuring and mounting the drive.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 20 3.4 D RIVE MOUNTING You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom- mounting holes. Follow these important mounting precautions when mounting the drive: • Allow a minimum clearance of 0.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 21 3.5 C OOLING Cabinet cooling must be designed by the customer so that the ambient temperature immediately surrounding the drive will not exceed temperature conditions specified in Section 2.9.1, "Temperature.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 22 4.0 S ERIAL ATA (SATA) INTERFACE These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 23 Table 10 summarizes the 1.8” drive Signal and Power SATA Plug . Notes: [1] Ground pins 3 and 4 mate first on micro SATA backplane connectors [2] The two V 33 pins are unused but connected together on the drive.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 24 4.3 S UPPORTED ATA COMMANDS Th e f o ll o w in g t a bl e l i st s S e ri a l A TA s t a nd a r d co m m an d s t ha t t h e dr ive s u p po r t s. F o r a d et a i le d d e sc r i pt i o n of t h e A TA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification .
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 25 Set Multiple Mode C6 H Sleep E6 H S.M.A.R.T. Disable Operations B0 H / D9 H S.M.A.R.T. Enable Operations B0 H / D8 H S.M.A.R.T. Execute Offline B0 H / D4 H S.M.A.R.T. Read Data B0 H / D0 H S.M.A.R.T.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 26 4.3.1 Identify Device command The Identify Device command (command code EC H ) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 11 on page 24.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 27 67 Minimum PIO transfer cycle time without flow control (120ns) 0078 H 68 Minimum PIO transfer cycle time with IORDY flow control (120ns) 0078 H 69 Additional Features and Commands supported.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 28 Note. See the bit descriptions below for words 49, 69, 76, 78, 82-87 and 119-120 of the Identify Drive data.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 29 Bit Word 69 5 Read zero after Trim is supported 6 Optional ATA 28-bit commands supported 8 Download Microcode DMA supported 9 Set Max Password DMA .
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 30 Bit Word 83 0 DOWNLOAD MICROCODE command is supported 1 Obsolete 2 CFA feature set is supported 3 APM feature set is supported 4 Obsolete 5 PUIS fe.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 31 Bit Word 87 0 SMART error logging is supported 1 SMART self-test supported 3 The Media Card Pass Through Command feature set is supported 5 The GPL.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 32 4.3.2 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features regis ter, clears BSY and generates an interrupt.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 33 4.3.3 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 34 I NDEX A ACA 17 acceleration 15 Access time 6 Agency certification 17 air flow illustrated 21 altitude 14 ambient temperature 6 , 7 Annualized Fail.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 35 I NDEX mounting the drive 19 N nominal power 6 Nonoperating shock 14 Nonoperating vibration 15 NOP 24 O Operating shock 14 Operating vibration 15 P.
S EAGATE 600 P RO SSD P RODUCT M ANUAL , R EV . A 36 I NDEX width 6 Write Buffer 25 Write DMA 25 Write DMA Extended 25 Write DMA FUA Extended 25 Write FPDMA queued 25 Write Log Extended 25 Write Multi.
Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard, Cupertino, California 95014, United States, 408-658-1000 ASIA/PACIFIC Seagate Singapore International Headquarters Pte.
Ein wichtiger Punkt beim Kauf des Geräts Seagate ST200FP0001 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Seagate ST200FP0001 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Seagate ST200FP0001 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Seagate ST200FP0001 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Seagate ST200FP0001 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Seagate ST200FP0001 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Seagate ST200FP0001 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Seagate ST200FP0001. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Seagate ST200FP0001 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
