DE
Niko logo
Offizielle Bedienungsanleitung

Niko 10-161

32 Seiten·2.5 MB·Sicherheitstechnik·PDF·ENITJA
Niko 10-161
Inhaltsverzeichnis 6 Abschnitte 3. INSTALLATION 3.1. Mounting and connecting the external video unit · 4. PROGRAMMING AND USE · 5. MAINTENANCE · 6. TROUBLESHOOTING · … AnzeigenAusblenden
Page 1 of the Niko 10-161 user manual
Seite 1 · Zum Vergrößern klicken
Seite 1

Read the complete user manual before carrying out the installation and activating the system.

1. DESCRIPTION This external video unit from the Niko Access Control range is always a standard part of a system with one or more internal units and a power supply. More information on how the product is integrated into a complete system can be found in the catalogue.

The external unit is a compact surface-mounting unit with a 16 mm mounting height. The external unit is provided with a colour camera with infrared LEDs for optimal visibility at night, as well as an adjustable microphone and loudspeaker. The nameplate is illuminated in the dark.

The external video unit is available with one bell push button (10-161), two bell push buttons (10- 162) or three bell push buttons (10-163).

Niko 10-161 diagram (page 1)
Abb. 1
Page 2 of the Niko 10-161 user manual — 3. INSTALLATION 3.1. Mounting and connecting the external video unit
Seite 2 · Zum Vergrößern klicken
Seite 2

2. COMPONENTS 2.1. Basic components 1. camera 2. loudspeaker 3. opening for key 4. service set connector 5. microphone 6. nameplate 7. potentiometers for volume adjustment of the microphone and loudspeaker 8. connection terminals 9. cable inlet 10. holes for wall mounting 11. metal protective cap 12. clamping springs for fixing the nameplate 13. namecard 14. infrared LEDs 15. light sensor 16. connection point for nameplate lighting 17. lighting element for nameplate 18. serial number 19. selection switch for six-wire/five-wire cabling 20. connector for nameplate lighting 21. bell push button 2.2. Additional accessoires The external video unit is connected using six-wire cabling. Use a twisted cable for optimal video image quality. Also pay attention to the diameter of the wires in the cable, as this determines the maximum distance that can be covered between the power supply and the external video unit.

  • Niko recommends using the following cables to install the external video unit:
  • JYSTY (-F2) min. 3 x 2 x 0.8 mm (max. distance 200 m)
  • TVVF (-F2) min. 3 x 2 x 0.8 mm (max. distance 200 m)
  • TPVF min. 3 x 2 x 0.6 mm (max. distance 100 m)
  • UTP/FTP/STP 4 x 2 x 0.5 mm (max. distance 70 m)
  • Function of the wires to be connected:
  • terminals a and b : communication bus (24 Vdc)
  • terminals V1 and V2 : video signal
  • terminals P and M : extra power supply (26 Vdc)

3. INSTALLATION 3.1. Mounting and connecting the external video unit

Page 3 of the Niko 10-161 user manual — 3. INSTALLATION 3.1. Mounting and connecting the external video unit
Seite 3 · Zum Vergrößern klicken
Seite 3
1. Remove the nameplate and carefully loosen the connector for the nameplate lighting (fig. 1).
Niko 10-161 — 3. INSTALLATION 3.1. Mounting and connecting the external video unit diagram (page 3)
Abb. 2 · 3. INSTALLATION 3.1. Mounting and connecting the ext…
2. Mount the external unit on the wall. The recommended installation height for the ca mera is 160 to 170 cm from the ground. Run the cable from the bottom up in the device in order to avoid water entering the device via the cable.
3. Connect the wiring as shown in the wiring diagram on 28.

fig. 1

4. You can fill out the provided blank namecard and add it to the nameplate. Carefully open the nameplate with a small screwdriver or with the key provided (fig. 2).
5. Reinsert the nameplate into the external unit.

fig. 2

3.2. Connecting an extra door opener relay

Niko 10-161 — 3. INSTALLATION 3.1. Mounting and connecting the external video unit diagram (page 3)
Abb. 3 · 3. INSTALLATION 3.1. Mounting and connecting the ext…

You can optionally connect a door opener relay to the external unit between terminals R and P. This relay is necessary:

  • if several external units are used.
  • if the external unit is to be provided with a local door opener contact.

3.3. Six-wire/five-wire cabling

In systems of a limited size, you can choose five-wire cabling. In this case, you do not need to connect a cable to the M-terminal. You should set up all the jumpers on the five-wire cabling configuration. EN

Page 4 of the Niko 10-161 user manual — 3. INSTALLATION 3.1. Mounting and connecting the external video unit
Seite 4 · Zum Vergrößern klicken
Seite 4
Niko 10-161 — 3. INSTALLATION 3.1. Mounting and connecting the external video unit diagram (page 4)
Abb. 4 · 3. INSTALLATION 3.1. Mounting and connecting the ext…
Page 5 of the Niko 10-161 user manual — 4. PROGRAMMING AND USE
Seite 5 · Zum Vergrößern klicken
Seite 5

4. PROGRAMMING AND USE

4.1. Programming the bell push button

Programming of a bell push button is described in detail in the manual of the system power supply (10- 801, 10-802 or 10-806) or the service set (10-870).

If you use the service set, tear off the serial number that you will find behind the nameplate or in the box. Stick this serial number on the installation diagram.

You can programme only two internal units in the memory location of each bell push button. If you want to use more internal units, you will need to programme them parallel (master/slave). See manual of the service set or internal unit.

A non-programmed bell push button will switch the light relay of the power supply.

4.2. General operation

If everything has been correctly connected and you switch on the external unit, the LED of the external unit will light up. When picking up the receiver of an internal unit, communication with the external unit should be possible at all times.

If you press:

  • a non-programmed bell push button , you will hear a high beep and the light relay of the power supply is switched.
  • a programmed bell push button , you will hear the bell ringing at the external and the internal unit. The image of the visitor is displayed on the internal video unit.

4.3. Nameplate lighting

The lighting of the nameplate is dependent on the ambient light. When there is sufficient ambient light, the background lighting of the nameplate switches off. Cover the light sensor with your hand to test this operation.

Page 6 of the Niko 10-161 user manual — 6. TROUBLESHOOTING
Seite 6 · Zum Vergrößern klicken
Seite 6

4.4. Adjusting the volume on the external unit

There are two potentiometers under the nameplate with which you can adjust the volume on the external unit.

potentiometer for loudspeaker (volume on external unit) potentiometer for microphone (volume on internal unit)

4.5. Setting times

By default, the following times are programmed:

speech time after initiating a call max. 2 min

time that the camera image remains active 80 s

time that a call from an external unit remains indicated 2 min

You can also set other times via:

  • the power supply . For more information on programming via the power supply, see manual of the power supply.
  • the service set . For more information on programming via the service set, see manual of the service set.
  • the relay .

5. MAINTENANCE

To prevent the surface of the product from becoming damaged by incorrect handling, consider the following maintenance tips:

  • Clean the product with a small quantity of soap and a damp cloth.
  • Never use abrasive sponges or aggressive cleaning agents.
  • Never use maintenance products that contain a solvent or an acid.
  • Never use cleaning products that contain acetic acid.

6. TROUBLESHOOTING

Using a multimeter, always first check whether the following voltages are present:

  • between b and a: ± 24 Vdc
  • between b and P: ± 24 Vdc
  • between M and P: ± 24 Vdc
  • between b and V1 or V2: ± 5 Vdc (b or M = mass)
Page 7 of the Niko 10-161 user manual — 7. TECHNICAL DATA
Seite 7 · Zum Vergrößern klicken
Seite 7

Programming error or associated internal unit not correctly installed.

Negative tone when pressing the bell push button.

Erase programming, then restart programming.

Installation in programming mode. Quit programming mode.

Speech and other functions (e.g. door opener) are working, but there is no image.

Check cabling on the power supply, internal unit and external unit using the wiring diagram. The image is completely disturbed and unrecognisable (striping, …).

The internal or external unit receives no power.

V1 and V2 are reversed. Reverse the conductors.

7. TECHNICAL DATA

Dimensions: 175 x 104 x 16 (19) mm (HxWxD) Ambient temperature: -20 – 50°C Housing material: aluminium/acryl glass Power consumption: active I(P) = 180 mA – passive I(P) = 125 mA – I(a) = 0.4 mA Power supply voltage: 24 Vdc ± 8% Camera: CCD sensor 420 lines

light sensitivity: 0.2 lux focal distance: 3.7 mm diagonal opening angle: 90° video output: 1 Vpp, symmetrical

8. WARNINGS REGARDING INSTALLATION - The installation should be carried out by a registered installer and in compliance with the statutory

regulations. - This user manual should be presented to the user. It should be included in the electrical installation file,

and it should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko support service. - During installation, the following should be taken into account (non-exhaustive list):

- the statutory laws, standards and regulations. - the technology currently available at the time of installation. - this user manual, which only states general regulations and should therefore be read within the scope

of each specific installation. - the rules of proper workmanship. - In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko

support service (Belgium: +32 3 778 90 80 – United Kingdom: +44 1525 877 707) or your wholesaler. Contact details and more information can be found at www.niko.eu under the “Help and advice” section.

Problem Cause Solution

Page 8 of the Niko 10-161 user manual — 9. GUARANTEE PROVISIONS
Seite 8 · Zum Vergrößern klicken
Seite 8

9. GUARANTEE PROVISIONS

- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of

purchase of the product by the consumer. If there is no invoice, the date of production applies. - The consumer is obliged to inform Niko in writing about the non-conformity, within two months after

stating the defect. - In case of a non-conformity, the consumer only has the right to a product repair or replacement free of

charge, which shall be decided by Niko. - Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or

careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance instructions or an external cause, such as damage due to moisture or overvoltage. - The compulsory regulations of the national legislation concerning the sale of consumer goods and

the protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries, chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned rules and regulations.

PM010-16x00R11342

Quellen

Referenzen & Links

In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.

Reparatur

Fehlerbehebung

Häufige Probleme, wahrscheinliche Ursachen und Lösungen.

ProblemMögliche UrsacheAbhilfe
Negative tone when pressing the bell push button.Programming error or associated internal unit not correctly installed.Erase programming, then restart programming. p.7
Negative tone when pressing the bell push button.Installation in programming mode.Quit programming mode. p.7
Speech and other functions (e.g. door opener) are working, but there is no image.The internal or external unit receives no power.Check cabling on the power supply, internal unit and external unit using the wiring diagram. p.7
The image is completely disturbed and unrecognisable (striping, …).V1 and V2 are reversed.Reverse the conductors. p.7

Frage zu Niko 10-161 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Niko 10-161

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Niko 10-161 PDF-Anleitung

32 Seiten·2.5 MB·Sicherheitstechnik·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…