


















WARNING
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capa- bilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Only for EU countries Do not dispose of electric equipment or battery pack together with household waste material! In observance of the European Directives, on Waste Electric and Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws, electric equipment and batteries and battery pack(s) that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
The followings show the symbols used for the equip- ment. Be sure that you understand their meaning before use.
Read instruction manual.
Ni-MH Li-ion

The tool is intended for collecting dry dust.
ADDITIONAL SAFETY RULES
This appliance is intended for household use. 1. Read this instruction manual and the charger instruction manual carefully before use. 2. Do not pick up the following materials: — Hot materials such as lit cigarettes or spark/metal dust generated by grinding/ cutting metal — Flammable materials such as gasoline, thinner, benzine, kerosene or paint — Explosive materials like nitroglycerin — Ignitable materials such as Aluminum, zinc, magnesium, titanium, phosphorus or celluloid — Wet dirt, water, oil or the like — Hard pieces with sharp edges, such as wood chips, metals, stones, glasses, nails, pins or razors — Powder to clot such as cement or toner — Conductive dust such as metal or carbon — Fine particle like concrete dust Such action may cause fire, injury and/or prop- erty damage. 3. Stop operation immediately if you notice any- thing abnormal. 4. If you drop or strike the cleaner, check it care- fully for cracks or damage before operation. 5. Do not bring close to stoves or other heat sources. 6. Do not block the intake hole or vent holes. SAVE THESE INSTRUCTIONS.
1. Do not expose to rain. Store indoors. 2. Do not allow to be used as a toy. Close attention is necessary when used by or near children. 3. Use only as described in this manual. Use only manufacturer's recommended attachments. 4. Do not use with damaged battery. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center. 5. Do not handle appliance with wet hands. 6. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow. 7. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts. 8. Turn off all controls before removing the battery. 9. Use extra care when cleaning on stairs. 10. Do not use to pick up flammable or combusti- ble liquids, such as gasoline, or use in areas where they may be present. 11. Use only the charger supplied by the manufac- turer to recharge. 12. Do not pick up anything that is burning or smok- ing, such as cigarettes, matches, or hot ashes. 13. Do not use without dust bag and/or filters in place. 14. Do not charge the battery outdoors. 15. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 16. Use power tools only with specifically desig- nated battery packs. Use of any other battery packs may create a risk of injury and fire. 17. When (the) battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. 18. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If con- tact accidentally occurs, flush with water. 19. Do not use a battery pack or tool that is dam- aged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

5. Do not short the battery cartridge: (1) Do not touch the terminals with any con- ductive material. (2) Avoid storing battery cartridge in a con- tainer with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation require- ments. For commercial transports e.g. by third parties, forwarding agents, special requirement on pack- aging and labeling must be observed. For preparation of the item being shipped, consult- ing an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. 11. Follow your local regulations relating to dis- posal of battery. 12. Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, exces- sive heat, explosion, or leak of electrolyte. SAVE THESE INSTRUCTIONS.
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
The tool is equipped with a tool/battery protection sys- tem. This system automatically cuts off power to the motor to extend tool and battery life. The tool will auto- matically stop during operation if the tool or battery is placed under one of the following conditions.
Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery car- tridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room tem- perature at 10 °C - 40 °C (50 °F - 104 °F). Let a hot battery cartridge cool down before charging it. 4. Charge the battery cartridge if you do not use it for a long period (more than six months).
Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before turning the tool on again.
Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.


Only for battery cartridges with the indicator ► Fig.3: 1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indi- cate the remaining battery capacity. The indicator lamps light up for a few seconds.

Install either dust bag or paper filter before using cleaner. Use the dust stopper when installing either dust bag or paper filter. Dust bag are usable many times repeatedly by cleaning it out. Paper filter is a throw-away type. Throw away the entire paper filter without emptying when it has become full.
Otherwise the motor may be broken.
To start the cleaner, simply push the ON/speed change button. To switch off, push the OFF button. You can change the cleaner speed in three steps by pushing the ON/speed change button. The first push on this button is for high speed mode, the second push for max speed mode and the third push for normal speed mode. Each push on this button repeats the high/max/normal speed cycle alternatively.
Use the dust stopper when installing dust bag. Be careful not to take the upper side for the lower side by mistake because they are different each other. ► Fig.7: 1. Upper side of dust stopper 2. Lower side of
To turn on the lamp, push the ON/speed change button. Push the OFF button to turn off the lamp. During the tool actuating, the lamp turns on. When the remaining battery capacity gets low, the lamp starts blinking. ► Fig.5: 1. ON/speed change button 2. OFF button
dust stopper

To install the extension wand, insert it to the suction inlet of the cleaner until it clicks. Make sure that the extension wand is locked. ► Fig.22: 1. Suction inlet 2. Extension wand 3. Hook
Use the dust stopper also when installing paper filter. Be careful not to take the upper side for the lower side by mistake because they are different each other. ► Fig.14: 1. Upper side of dust stopper 2. Lower side
To remove, pull the extension wand while pushing the release button. ► Fig.24: 1. Release button 2. Extension wand
To install the nozzle, twist and insert it securely to the suction inlet of the cleaner or the end of extension wand. To disconnect, twist and remove it. ► Fig.25
Attach the nozzle to clean off tables, desks, furniture, etc. The nozzle slips on easily. ► Fig.26: 1. Nozzle
The extension wand fits in between the nozzle and the cleaner itself. This arrangement is convenient for clean- ing a floor in a standing position. ► Fig.27: 1. Cleaner body 2. Extension wand
OPERATION
Fit on the corner nozzle for cleaning corners and crev- ices of a car or furniture. ► Fig.28: 1. Corner nozzle 2. Cleaner body
In tight quarters where the cleaner itself cannot squeeze in, or in high places hard to reach, use this arrangement. ► Fig.29: 1. Corner nozzle 2. Extension wand
You can pick up powder and dust without nozzle. ► Fig.30
For picking up dust on a floor in a standing position, it is convenient to attach the extension wand to the cleaner. ► Fig.31: 1. Extension wand
of dust stopper · filter

After use
Cleaner body
From time to time wipe off the outside (cleaner body) of the cleaner using a cloth dampened in soapy water. Clean out also the suction opening, dust bag/paper filter mounting area and the dust stopper. ► Fig.38
Wash the dust bag in soapy water when it is clogged with dust and the cleaner power becomes weak. Dry it out thor- oughly before use. An insufficiently dried filter may cause poor suction and shorten the service life of the motor. ► Fig.39
When the sponge filter is clogged with dust, remove it from the cleaner and then wipe it off or wash in water.
When using the dust bag Remove the dust stopper and empty the dust bag. ► Fig.34: 1. Dust stopper 2. Dust bag
Wipe dust off from the dust stopper. Remove dust and dirt on the sponge part by lightly tapping it. ► Fig.40: 1. Sponge part
When using the paper filter Remove the dust stopper and dispose of the paper filter. ► Fig.35: 1. Dust stopper 2. Paper filter
To remove the sponge filter, remove the dust bag or paper filter and then pinch and take the sponge filter out. ► Fig.41: 1. Sponge filter
Press in the whole edge of the sponge filter against the recessed wall inside the dust bag/paper filter mounting area. ► Fig.42: 1. Recessed wall
Attach the wall mount for cordless cleaner to a hard wooden wall, beam or column, where the wall mount for cordless cleaner can be firmly secured. Always be sure that the wall mount for cordless cleaner is securely attached before hanging the cleaner. ► Fig.43: 1. Wall mount for cordless cleaner
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Optional accessory

Before asking for repairs, check the following points.
Symptom Area to be investigated Fixing method
Weak suction power Is dust bag or paper filter full of dust ? Empty dust bag or paper filter.
Is dust bag clogged ? Dust down or wash the dust bag.
Is paper filter clogged ? Replace paper filter.
Is the battery cartridge exhausted ? Charge the battery cartridge.
Not working Is the battery cartridge exhausted ? Charge the battery cartridge.
Dust case cover does not close Is dust bag or paper filter set ? Set dust bag or paper filter.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.