DE
Hitachi logo
Offizielle Bedienungsanleitung

Hitachi DV18DVC

78 Seiten·1.5 MB·Akkubohrschrauber·PDF·ENJA
Hitachi DV18DVC
Inhaltsverzeichnis 14 Abschnitte DV18DCL · GENERAL SAFETY RULES · PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL · CAUTION ON LITHIUM-ION BATTERY · … AnzeigenAusblenden
Page 1 of the Hitachi DV18DVC user manual — DV18DCL
Seite 1 · Zum Vergrößern klicken
Seite 1

Cordless Impact Driver Drill Akku-Schlagbohrschrauber Perceuse percussion/visseuse à batterie Trapano avvitatore a percussione a batteria Snoerloze klop-boor-schroefmachine Taladro atornillador de impacto a batería Berbequim aparafusador de impacto a bateria ∆ραπανκατσά ιδ µπαταρίας κρυστικ

  • DV 18DCL
  • DV 14DVC
  • DV 18DVC

DV18DCL

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste instruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções. ∆ιαάστε πρ σεκτικά και καταν ήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso δηγίες ειρισµ ύ

Page 2 of the Hitachi DV18DVC user manual — DV18DCL
Seite 2 · Zum Vergrößern klicken
Seite 2
Hitachi DV18DVC — DV18DCL diagram (page 2)
Abb. 1
Page 3 of the Hitachi DV18DVC user manual — DV18DCL
Seite 3 · Zum Vergrößern klicken
Seite 3
EnglishDeutschFrançaisItaliano 118 V Rechargeable battery (For DV18DCL)18 V aufladbare Batterie (Für DV18DCL)Batterie rechargeable 18 V (Pour DV18DCL)Batteria ricaricabile da 18 V (Per DV18DCL) 214.4 V Rechargeable battery (For DV14DVC)14,4 V aufladbare Batterie (Für DV14DVC)Batterie rechargeable 14,4 V (Pour DV14DVC)Batteria ricaricabile da 14,4 V (Per DV14DVC) 318 V Rechargeable battery (For DV18DVC)18 V aufladbare Batterie (Für DV18DVC)Batterie rechargeable 18 V (Pour DV18DVC)Batteria ricaricabile da 18 V (Per DV18DVC) 4LatchVerriegelungTaquetFermo 5Pull outHerausziehenTirer vers l’extérieurEstrarre 6InsertEinsetzenInsérerInserire 7HandleHandgriffPoignéeImpugnatura 8InsertEinsetzenInsérerInserire 9Pilot lampKontrollampeLampe témoinSpia 0Hole for connecting the rechargeable batteryAnschlußloch für LadebatterirOrifice de raccordemente de la batterie echargeableForo di collegamento della batteria ricaricabile ADrill markBohrer-ZeichenIndice de forageSimbolo di foratura BHammer markHammermarkierungRepère de percussionSegno del martello CCapKappeCapotCappuccio DTriangle markDreiecksmarkierungTriangleSimbolo del triangolo EWeakSchwachFaibleDebol FStrongStarkFortForte GBlack lineSchwarze LinieTrait noirLinea nera HShift knobSchaltknopfBouton de décalageManopola di comando ILow speedKleine GeschwindigkeitVitesse ralentieBassa velocità JHigh speedGroße GeschwindigkeitVitesse élevéeAlta velocità KRingRingAnneauAnello LSleeveManschetteManchonCollare MTightenAnziehenSerrerStringere NLooseLösenDesserrerAllentare OTrigger switchTriggerDéclencheurInterruttore PSelector buttonWählhebelSélecteurSelettore
Page 5 of the Hitachi DV18DVC user manual — GENERAL SAFETY RULES
Seite 5 · Zum Vergrößern klicken
Seite 5

GENERAL SAFETY RULES

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust

SAVE THESE INSTRUCTIONS 1) Work area a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive

extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust of fumes. c) Keep children and bystanders away while operating

4. Power tool use and care a) Do not force the power tool. Use the correct

a power tool. Distractions can cause you to lose control.

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not

2. Electrical safety a) Power tool plugs must match the outlet.

turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source before

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or

conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for

binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc.,

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

3. Personal safety a) Stay alert, watch what you are doing and use

in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in a hazardous situation.

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use safety equipment. Always wear eye protection.

Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Avoid accidental starting. Ensure the switch is in

5. Service a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons.

Page 6 of the Hitachi DV18DVC user manual — PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL
Seite 6 · Zum Vergrößern klicken
Seite 6

PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 and 2 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function. 1. When the battery power remaining runs out (The battery voltage drops to about 12V), the motor stops. In such case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

1. Always charge the battery at a temperature of 0 – 50°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 50°C. The most suitable temperature for charging is that of 20 – 25°C. 2. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 7. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 9. Using an exhausted battery will damage the charger. 10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.

Page 7 of the Hitachi DV18DVC user manual — OPTIONAL ACCESSORIES (sold separately)
Seite 7 · Zum Vergrößern klicken
Seite 7

SPECIFICATIONS

POWER TOOL

ModelDV18DCLDV14DVCDV18DVC No-load speed (Low/High)0–400 / 0–1500 min–10–400 / 0 – 1500 min–1 0–400 / 0–1500 min–1 No-load impact rate (Low/High)0–5,600 / 0–21000 min–10–5,600 / 0 – 21000 min–1 0–5600 / 0–21000 min–1 CapacityBrick (Depth 30 mm)13 mm13 mm13 mm DrillingWood (Thickness 18 mm)38 mm32 mm38 mm Metal (Thickness 1.6 mm)13 mm13 mm13 mm DrivingMachine screw6 mm6 mm6 mm Wood scre8 mm (diameter) × 75 mm (length) (Requires a pilot hole)8 mm (diameter) × 50 mm (length) 8 (Requires a pilot hole) (mm (diameter) × 75 mm (length) Requires a pilot hole) Rechargeable batteryEBM1830:Li-ion 18V (3.0Ah 10cells)EB1414S:Ni-Cd 14.4 V (1.4Ah 12cells) EB EB14B :Ni-Cd 14.4 V (2.0Ah 12cells) EB EB1424 :Ni-Cd 14.4 V (2.4Ah 12cells) EB1814SL:Ni-Cd 18V (1.4Ah 15cells) 1820L :Ni-Cd 18V (2.0Ah 15cells) 1824L :Ni-Cd 18V (2.4Ah 15cells) Weight2.0 kg1.9 kg2.1 kg CHARGER 2. Battery (EB1414S, EB14B, EB1424) (For DV14DVC) Model UC18YRL UC18YG Charging voltage 7.2 – 18 V 7.2 – 18 V Weight 0.6 kg 0.3 kg CAUTION UC18YG: Ni-Cd battery only STANDARD ACCESSORIES 3. Battery (EB1814SL, EB1820L, EB1824L) (For 1 Plus driver bit (No. 2 × 65L) 1 DV18DVC) DV18DCL 2 Charger (UC18YRL) 1 3 Plastic case 1 1 Plus driver bit (No. 2 × 65L) 1 DV14DVC 2 Charger (UC18YG) 1 3 Plastic case 1 1 Plus driver bit (No. 2 × 65L) 1 DV18DVC 2 Charger (UC18YG) 1 Optional accessories are subject to change without notice. 3 Plastic case 1 Standard accessories are subject to change without notice. APPLICATIONS
ModelUC18YRLUC18YG Charging voltage7.2 – 18 V7.2 – 18 V Weight0.6 kg0.3 kg
DV18DCL1 Plus driver bit (No. 2 × 65L) 1 2 Charger (UC18YRL) 1 3 Plastic case 1 DV14DVC1 Plus driver bit (No. 2 × 65L) 1 2 Charger (UC18YG) 1 3 Plastic case 1 DV18DVC1 Plus driver bit (No. 2 × 65L) 1 2 Charger (UC18YG) 1 3 Plastic case 1

Drilling of brick and concrete block, etc. Driving and removing of machine screws, wood

OPTIONAL ACCESSORIES (sold separately)

1. Battery (EBM1830, EB1814SL, EB1820L, EB1824L, EB1826HL, EB1830HL) (For DV18DCL)

screws, tapping screws, etc. Drilling of various metals Drilling of various woods

Page 8 of the Hitachi DV18DVC user manual — CHARGING
Seite 8 · Zum Vergrößern klicken
Seite 8

BATTERY REMOVAL/INSTALLATION

2. Insert the battery into the charger Insert the battery firmly, until it contacts the bottom of the charger compartment. CAUTION If the battery is inserted in the reverse direction, not
1. Battery removal Hold the handle tightly and push the battery latch (2 pcs.) to remove the battery (see Figs. 1 and 2 ). CAUTION

only recharging will become impossible, but it may also cause problems in the charger such as deformed recharging terminal. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light up continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red (At 1-second intervals) (See Table 1). (1) Pilot lamp indication

Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (see Fig. 2).

CHARGING

〈UC18YRL〉 Before using the power tool, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle When the power cord is connected, the charger’s pilot lamp will blink in red (At 1-second intervals).

The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

Indications of the lamps Before chargingLights for 0.5 seconds. Does not light for Blinks 0.5 seconds. (off for 0.5 seconds) (RED) While chargingLights Lights continuously (RED) Charging completeLights for 0.5 seconds. Does not light for Blinks 0.5 seconds. (off for 0.5 seconds) (RED) Charging impossibleLights for 0.1 seconds. Does not light for Flikers 0.1 seconds. (off for 0.1 seconds) (RED)Malfunction in the battery or the charger. Overheat standbyLights Lights continuously (GREEN)Battery overheated. Unable to charge (Charging will commence when battery cools).

(2) Regarding the temperatures of the rechargeable

Table 3 Charging time (At 20°C)

battery The temperatures for rechargeable batteries are as shown in the table below, and batteries that have become hot should be cooled for a while before being recharged.

Charger BatteryUC18YRLUC18YG EB14BApporx. 20 min.Apporx. 30 min. BCC1414C EB1414S EB1814SL, BCC1814C EB1820LApporx. 30 min.Apporx. 50 min. EB1424Apporx. 35 min.Apporx. 60 min. EB1426HApporx. 40 min. EB1824LApporx. 35 min.Apporx. 60 min. EB1826HLApporx. 40 min. EB1430HApporx. 45 min. EB1830HL EBM1830

Table 2 Recharging ranges of batteries

Charger Rechargeable batteriesUC18YRL Ni-Cd batteries–5°C – 55°C Ni-MH batteries–5°C – 50°C Li-ion batteries0°C – 50°C

(3) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.

Table 1

Page 9 of the Hitachi DV18DVC user manual — HOW TO USE
Seite 9 · Zum Vergrößern klicken
Seite 9
4. Disconnect the charger’s power cord from the receptacle 5. Hold the charger firmly and pull out the battery NOTE

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

Be sure to pull out the battery from the charger after use, and then keep it. CAUTION If the battery is charged while it is heated because it

has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the pilot lamp of the charger lights up green. In such a case, first let the battery cool, then start charging. When the pilot lamp flikers in red quickly (at 0.2-

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your Authorized Service Center. Since the built-in micro computer takes about 3

PRIOR TO OPERATION

1. Setting up and checking the work environment Check if the work environment is suitable by following the precautions.

seconds to confirm that the battery being charged with UC18YRL is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. 〈UC18YG〉 Before using the power tool, charge the battery as follows. 1. Connect the charger power cord to the receptacle Connecting the power cord will turn on the charger. 2. Insert the battery into the charger Insert the battery firmly while observing its direction, until it contacts the bottom of the charger (the pilot lamp lights up). CAUTION

HOW TO USE

1. Confirm the cap position (see Fig. 5) The three modes of screwdriver, drill and impact drill can be switched by the position of the cap in this unit. (1) When using this unit as a screwdriver, line up the one

of the numbers “1, 4, 7 ... 22” on the cap, or the black dots, with the triangle mark on the outer body. (2) When using this unit as a drill, align the cap drill mark

” with the triangle mark on the outer body. (3) When using this unit as an impact drill, align the cap

If the pilot lamp does not light up, pull out the power cord from the receptacle and check the battery mounting condition. The pilot lamp goes off to indicate that the battery is fully charged. The battery charging time becomes longer when a temperature is low or the voltage of the power source is too low. When the pilot lamp does not go off even if more than 120 minutes have elapsed after starting of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER. CAUTION

” with the triangle mark on the outer body. CAUTION The cap cannot be set between the numerals “1, 4, 7

... 22” or the black dots. Do not use with the cap numeral between “22” and

the black line at the middle of the drill mark. Doing so may cause damage (See Fig. 6). 2. Tightening torque adjustment (1) Tightening torque

Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the cap position according to the screw diameter. (2) Tightening torque indication

If the battery is heated due to direct sunlight, etc., just after operation, the charger pilot lamp may not light up. At that time, cool the battery first, then start charging. 3. Disconnect the charger power cord from the receptacle 4. Hold the charger tight and pull out the battery

The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 4, 7 ... 22” on the cap, and the black dots. The tightening toque at position “1” is the weakest and the torque is strongest at the highest number (See Fig. 5). (3) Adjusting the tightening torque

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.

Rotate the cap and line up the numbers “1, 4, 7 ... 22” on the cap, or the black dots, with the triangle mark on the outer body. Adjust the cap in the weak or the strong torque direction according to the torque you need. CAUTION The motor rotation may be locked to cease while the

unit is used as drill. While operating the impact driver drill, take care not to lock the motor.

“ · hammer mark “

Page 10 of the Hitachi DV18DVC user manual — PRIOR TO OPERATION
Seite 10 · Zum Vergrößern klicken
Seite 10

Too long hammering may cause the screw broken

at a high speed. CAUTION When changing the rotational speed with the shift

due to excessive tightening. 3. Rotation to Impact changeover (See Fig. 5) The “Rotation (Rotation only)” and “Impact (Impact + Rotation)” can be switched by aligning the drill mark “

knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears. When setting the shift knob to “HIGH” (high speed)

” with the triangle mark on the outer body. To make holes in the metal, wood or plastic, switch

” or the hammer mark “

and the position of the cap is bitween “16” and “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). If the motor is locked, immediately turn the power

to “Rotation (Rotation only)”. To make holes in bricks or concrete blocks, switch to

“Impact (Impact + Rotation)”. CAUTION

If an operation which is normally performed at the “Rotation” setting is performed at “Impact “ setting,the effect of making holes does not only increase but it may also damage the bit or other parts. 4. Change rotation speed Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (see Figs. 7 and 8). When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates

off. If the motor is locked for a while, the motor or battery may be burnt. To extend the lifetime, the lithium-ion battery equips

with the protection function to stop the output. Therefore, if the tool is overloaded, the motor may stop. However, this is not the trouble but the result of protection function. In this case, release the switch of tool and eliminate the causes of overloading. 5. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.

WorkSuggestions DrillingBrickUse for drilling purpose. Wood Steel Aluminum DrivingMachine screwUse the bit or socket matching the screw diameter. Wood screwUse after drilling a pilot hole.
6. How to select tightening torque and rotational speed
UseCap PositionRotating speed selection (Position of the shift knob) LOW (Low speed)HIGH (High speed) DrivingMachine screw1 – 22For 6 mm or smaller diameter screws.For 6 mm or smaller diameter screws. Wood screw1 –For 6 mm or smaller nominal diameter screws.For 3.8 mm or smaller nominal diameter screws. DrillingBrickFor 13 mm or smaller diameters.For 8 mm or smaller diameters. (DV14DVC) For 10 mm or smaller diameters. (DV18DCL/ DV18DVC) WoodFor 32 mm or smaller diameters. (DV14DVC) For 38 mm or smaller diameters. (DV18DCL/ DV18DVC)For 18 mm or smaller diameters. (DV14DVC) For 22 mm or smaller diameters. (DV18DCL/ DV18DVC) MetalFor drilling with a metal working drill bit.

a bit may loose due to the tightning torque is too strong. Use the impact driver drill at LOW (low speed) when using a machine screw. NOTE

considered as general standard. As different types of tightening screws and different materials to be tightened are used in actual works proper adjustments are naturally necessary. When using the impact driver drill with a machine

The use of the battery EB1426H, EB1430H, EB1826HL, EB1830HL and EBM1830 in a cold condition (below 0 degree Centigrade) can sometimes result in the

screw at HIGH (high speed), a screw may damage or

Table 4 · Table 5

Page 11 of the Hitachi DV18DVC user manual — GUARANTEE
Seite 11 · Zum Vergrößern klicken
Seite 11

weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up. 7. Mounting and dismounting of the bit (1) After inserting a driver bit, etc. into the keyless drill

MAINTENANCE AND INSPECTION

1. Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Cleaning on the outside When the Impact driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 5. Storage Store the Impact driver drill in a place in which the temperature is less than 40°C and out of reach of children. 6. Service parts list CAUTION

chuck, firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front) (See Fig. 9). If the sleeve becomes loose during operation, tighten it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counter-clockwise direction as viewed from the front) (See Fig. 9). CAUTION When it is no longer possible to loosen the sleeve,

use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 11 and then turn the sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. 8. Confirm that the battery is mounted correctly 9. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise (See Fig. 10). (The L and R marks are provided on the selector button.) CAUTION Always use this unit with clockwise rotation, when

Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS

using it as an impact drill. 10. Switch operation When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops. The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE A buzzing noise is produced when the motor is about

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.

to rotate. This is only a noise, not a machine failure. 11. For drilling into brick Excessive pressing force never increases drilling speed. It will not only damage the drill tip or reduce working efficiency, but could also shorten the service life of drill bit. Operate the impact driver drill within 10-15 kg pressing force while drilling into brick. 12. Using the bit holder CAUTION Stow the bit in the specified location on the tool. If

GUARANTEE

We guarantee Hitachi Power Tools in accordance with statutory/country specific regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center.

the tool is used with the bit stowed improperly, the bit may fall and cause bodily injury. Do not stow bits that are of a different length, gauge

or dimension than the plus driver bit (65 mm long) included in the STANDARD ACCESSORIES. The bit may fall and cause bodily injury. (1) Removing the bit

Securely hold the main unit and pull out the bit by holding the tip with your thumb (Fig. 11). (2) Installing the Bit

Install the bit with steps opposite of when removing. Insert the bit so that the right and left sides are equal, as shown in Fig. 12.

Page 12 of the Hitachi DV18DVC user manual — MAINTENANCE AND INSPECTION
Seite 12 · Zum Vergrößern klicken
Seite 12

Blue: – Neutral Brown: – Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except United Kingdom.

Information concerning airborne noise and vibration The measured values were determined according to EN 60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level102 dB(A) Measured A-weighted sound pressure level: 89 dB(A) Uncertainty KpA: 3 dB(A)

Wear ear protection.

The typical weighted root mean square acceleration value: 7.7 m/s2.

Page 13 of the Hitachi DV18DVC user manual — DV18DCL
Seite 13 · Zum Vergrößern klicken
Seite 13

ITEM PART NAME Q’ty NO.

1 SPECIAL SCREW (LEFT HAND) M6_23 1 2 DRILL CHUCK 123VLRJ-N 1 3 GEAR BOX ASS’Y 1 4 CLUTCH DIAL 1 5 CLICK SPRING 1 6 O-RING 1 7 SPINDLE 1 8 SPRING (C) 1 9 RACHET (B) 1 10 WASHER 1 11 NUT 1 12 WASHER 1 13 SLIP BLOCK 2 14 STOPPER SPRING 2 15 FRONT CASE 1 16 SPRING (A) 6 17 STEEL BALL D5 6 18 WASHER 2 19 SPRING (D) 1 20 RING GEAR 1 21 CARRIER 1 22 PLANET GEAR (C) 3 23 WASHER (A) 1 24 REAR CASE 1 25 SCREW SET D3_12 4 26 SHIFT ARM 1 27 SLIDE RING GEAR 1 28 PINION (C) 1 29 PLANET GEAR (A) SET 6 30 PINION (B) 1 31 FIRST RING GEAR 1 32 WASHER (B) 1 33 MOTOR SPACER 1 34 MOTOR 1 35 NAME PLATE 1 36 TAPPING SCREW (W/FLANGE) D3_16 8 37 MACHINE SCREW (W/SP. WASHER) M4_6 2 38 FERRITE CORE 1 39 HITACHI LABEL 1 40 HOUSING (A), (B) SET 1 41 INTERNAL WIRE (BLACK) 160 1 42 INTERNAL WIRE (RED) 130L 1 43 PUSHING BUTTON 1 44 SHIFT KNOB 1 45 DC-SPEED CONTROL SWITCH 1 46 STRAP 1 47 TAPPING SCREW D4_10 2 48 HOLDER SPRING 2 49 TERMINAL 2 50 TERRMINAL PIECE 1 51 BATTERY EBM1830 1 501 + DRIVER BIT NO.2 65L 1 502 CHARGER (MODEL UC18YRL) 1 503 BIT SET 1

Hitachi DV18DVC — MAINTENANCE AND INSPECTION diagram (page 13)
Abb. 2

DV18DCL

Page 14 of the Hitachi DV18DVC user manual — DV14DVC
Seite 14 · Zum Vergrößern klicken
Seite 14

ITEM PART NAME Q’ty NO.

1 SPECIAL SCREW (LEFT HAND) M6_23 1 2 DRILL CHUCK 123VLRJ-N 1 3 GEAR BOX ASS’Y 1 4 CLUTCH DIAL 1 5 CLICK SPRING 1 6 O-RING 1 7 SPINDLE 1 8 SPRING (C) 1 9 RACHET (B) 1 10 WASHER 1 11 NUT 1 12 WASHER 1 13 SLIP BLOCK 2 14 STOPPER SPRING 2 15 FRONT CASE 1 16 SPRING (A) 6 17 STEEL BALL D5 6 18 WASHER 2 19 SPRING (D) 1 20 RING GEAR 1 21 CARRIER 1 22 PLANET GEAR (C) 3 23 WASHER (A) 1 24 REAR CASE 1 25 SCREW SET D3_12 4 26 SHIFT ARM 1 27 SLIDE RING GEAR 1 28 PINION (C) 1 29 PLANET GEAR (A) SET 6 30 PINION (B) 1 31 FIRST RING GEAR 1 32 WASHER (B) 1 33 MOTOR SPACER 1 34 MOTOR 1 35 NAME PLATE 1 36 TAPPING SCREW (W/FLANGE) D3_16 8 37 MACHINE SCREW (W/SP. WASHER) M4_6 2 38 FERRITE CORE 1 39 HITACHI LABEL 1 40 HOUSING (A), (B) SET 1 41 INTERNAL WIRE (BLACK) 160 1 42 INTERNAL WIRE (RED) 130L 1 43 PUSHING BUTTON 1 44 SHIFT KNOB 1 45 DC-SPEED CONTROL SWITCH 1 46 STRAP 1 47 TAPPING SCREW D4_10 2 48 HOLDER SPRING 2 49 TERMINAL 2 50 TERRMINAL PIECE 1 51 BATTERY BCC1814C 1 501 + DRIVER BIT NO.2 65L 1 502 CHARGER (MODEL UC18YG) 1

DV14DVC

Hitachi DV18DVC — DV14DVC diagram (page 14)
Abb. 3
Page 15 of the Hitachi DV18DVC user manual — DV14DVC
Seite 15 · Zum Vergrößern klicken
Seite 15

ITEM PART NAME Q’ty NO.

1 SPECIAL SCREW (LEFT HAND) M6_23 1 2 DRILL CHUCK 123VLRJ-N 1 3 GEAR BOX ASS’Y 1 4 CLUTCH DIAL 1 5 CLICK SPRING 1 6 O-RING 1 7 SPINDLE 1 8 SPRING (C) 1 9 RACHET (B) 1 10 WASHER 1 11 NUT 1 12 WASHER 1 13 SLIP BLOCK 2 14 STOPPER SPRING 2 15 FRONT CASE 1 16 SPRING (A) 6 17 STEEL BALL D5 6 18 WASHER 2 19 SPRING (D) 1 20 RING GEAR 1 21 CARRIER 1 22 PLANET GEAR (C) 3 23 WASHER (A) 1 24 REAR CASE 1 25 SCREW SET D3_12 4 26 SHIFT ARM 1 27 SLIDE RING GEAR 1 28 PINION (C) 1 29 PLANET GEAR (A) SET 6 30 PINION (B) 1 31 FIRST RING GEAR 1 32 WASHER (B) 1 33 MOTOR SPACER 1 34 MOTOR 1 35 NAME PLATE 1 36 TAPPING SCREW (W/FLANGE) D3_16 8 37 MACHINE SCREW (W/SP. WASHER) M4_6 2 38 FERRITE CORE 1 39 HITACHI LABEL 1 40 HOUSING (A), (B) SET 1 41 INTERNAL WIRE (BLACK) 160 1 42 INTERNAL WIRE (RED) 130L 1 43 PUSHING BUTTON 1 44 SHIFT KNOB 1 45 DC-SPEED CONTROL SWITCH 1 46 STRAP 1 47 TAPPING SCREW D4_10 2 48 HOLDER SPRING 2 49 TERMINAL 2 50 TERRMINAL PIECE 1 51 BATTERY BCC1814C 1 501 + DRIVER BIT NO.2 65L 1 502 CHARGER (MODEL UC18YG) 1

Hitachi DV18DVC — DV14DVC diagram (page 15)
Abb. 4
Page 16 of the Hitachi DV18DVC user manual — DV14DVC
Seite 16 · Zum Vergrößern klicken
Seite 16
Hitachi DV18DVC — DV14DVC diagram (page 16)
Abb. 5

Frage zu Hitachi DV18DVC stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Hitachi DV18DVC

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Hitachi DV18DVC PDF-Anleitung

78 Seiten·1.5 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…