DE
Hitachi logo
Offizielle Bedienungsanleitung

Hitachi DV18DFL

84 Seiten·5 MB·Akkubohrschrauber·PDF·ENJA
Hitachi DV18DFL
Inhaltsverzeichnis 38 Abschnitte GENERAL POWER TOOL SAFETY WARNINGS · PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL · CAUTION ON LITHIUM-ION BATTERY · SPECIFICATIONS · … AnzeigenAusblenden
Page 1 of the Hitachi DV18DFL user manual — GENERAL POWER TOOL SAFETY WARNINGS
Seite 1 · Zum Vergrößern klicken
Seite 1

GENERAL POWER TOOL SAFETY WARNINGS

Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains- operated (corded) power tool or battery-operated (cordless) power tool.

balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or

1. Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive

jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of

atmospheres, such as in the presence of fl ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while

dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards.

operating a power tool. Distractions can cause you to lose control.

4. Power tool use and care a) Do not force the power tool. Use the correct
2. Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodifi ed plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not

turn it on and off . Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source and/

surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet

or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment or

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

binding of moving parts, breakage of parts and any other condition that may aff ect the power tools’ operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location

is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety a) Stay alert, watch what you are doing and use

etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations diff erent from those intended could result in a hazardous situation.

common sense when operating a power tool. Do not use a power tool while you are tired or under the infl uence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear

5. Battery tool use and care a) Recharge only with the charger specifi ed by the

eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the

manufacturer. A charger that is suitable for one type of battery pack may create a risk of fi re when used with another battery pack. b) Use power tools only with specifi cally designated

switch is in the off -position before connecting to power source and/or battery pack, picking up or carrying the tool.

battery packs. Use of any other battery packs may create a risk of injury and fi re.

(Original instructions)

Page 2 of the Hitachi DV18DFL user manual — CAUTION ON LITHIUM-ION BATTERY
Seite 2 · Zum Vergrößern klicken
Seite 2

c) When battery pack is not in use, keep it away

1. When the battery power remaining runs out, the motor stops. In such case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again. 3. If the battery is overheated under overload work, the battery power may stop. In this case, stop using the battery and let the battery cool. After that, you can use it again. Furthermore, please heed the following warning and caution. WARNING In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions. 1. Make sure that swarf and dust do not collect on the battery. ○ During work make sure that swarf and dust do not fall on the battery. ○ Make sure that any swarf and dust falling on the power tool during work do not collect on the battery. ○ Do not store an unused battery in a location exposed to swarf and dust. ○ Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.). 2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock. 3. Do not use an apparently damaged or deformed battery. 4. Do not use the battery in reverse polarity. 5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. 6. Do not use the battery for a purpose other than those specifi ed. 7. If the battery charging fails to complete even when a specifi ed recharging time has elapsed, immediately stop further recharging. 8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container. 9. Keep away from fi re immediately when leakage or foul odor are detected. 10. Do not use in a location where strong static electricity generates. 11. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use. CAUTION 1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately. If left untreated, the liquid may cause eye-problems. 2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately. There is a possibility that this can cause skin irritation. 3. If you fi nd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the fi rst time, do not use and return it to your supplier or vendor.

from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fi re. d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact accidentally occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

6. Service a) Have your power tool serviced by a qualifi ed

repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

PRECAUTION Keep children and infi rm persons away. When not in use, tools should be stored out of reach of children and infi rm persons.

PRECAUTIONS FOR CORDLESS IMPACT DRIVER DRILL

1. Always charge the battery at a temperature of 0°C – 50°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 50°C. The most suitable temperature for charging is that of 20°C – 25°C. 2. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fi re. If the battery is burnt, it may explode. 7. When drilling in wall, fl oor or ceiling, check for buried electric power cord, etc. 8. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 9. Using an exhausted battery will damage the charger. 10. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or infl ammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 11. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

Page 3 of the Hitachi DV18DFL user manual — BATTERY REMOVAL/INSTALLATION
Seite 3 · Zum Vergrößern klicken
Seite 3

SPECIFICATIONS

POWER TOOL

ModelDV14DFLDV18DFL No-load speed (Low/High)0 – 400 / 0 – 1500 min-10 – 400 / 0 – 1500 min-1 No-load impact rate (Low/High)0 – 5600 / 0 – 21000 min-10 – 5600 / 0 – 21000 min-1 CapacityDrillingBrick (Depth 30 mm)13 mm13 mm Wood (Thickness 18 mm)32 mm38 mm Metal (Thickness 1.6 mm)13 mm13 mm DrivingMachine screw6 mm6 mm Wood screw8 mm (diameter) × 50 mm (length) (Requires a pilot hole)8 mm (diameter) × 75 mm (length) (Requires a pilot hole) Rechargeable batteryBCL1415: Li-ion 14.4 V (1.5 Ah 4 cells)BCL1815: Li-ion 18 V (1.5 Ah 5 cells) Weight1.5 kg1.6 kg

CHARGER

CHARGING

ModelUC18YGL2 / UC18YKL Charging voltage7.2 – 18 V Weight0.4 kg

Before using the power tool, charge the battery as follows. 1. Connect the charger’s power cord to the receptacle. When connecting the plug of the charger to a receptacle, the pilot lamp will blink in red (At 1-second intervals). 2. Insert the battery into the charger. Firmly insert the battery into the charger till it contacts the bottom of the charger and checking the polarities as shown in Fig. 3. CAUTION If the batteries are inserted in the reverse direction, not only recharging will become impossible, but it may also cause problems in the charger such as a deformed recharging terminal. 3. Charging When inserting a battery in the charger, the pilot lamp will light up continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red (At 1-second intervals). (See Table 1) (1) Pilot lamp indication The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

STANDARD ACCESSORIES

In addition to the main unit (1), the package contains the accessories listed in the table below.

DV14DFL DV18DFL1 Plus driver bit (No. 2 × 65L) 1 2 Charger (UC18YGL2 or UC18YKL) 1 3 Plastic case 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

1. Battery (BCL1415) (For DV14DFL) 2. Battery (BCL1815) (For DV18DFL) Optional accessories are subject to change without notice.

APPLICATIONS

○ Drilling of brick and concrete block, etc. ○ Driving and removing of machine screws, wood screws, tapping screws, etc. ○ Drilling of various metals. ○ Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal Hold the handle tightly and push the battery latch (2 pcs.) to remove the battery (see Figs. 1 and 2 ). CAUTION Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (see Fig. 2 ).
Page 4 of the Hitachi DV18DFL user manual — HOW TO USE
Seite 4 · Zum Vergrößern klicken
Seite 4
Indications of the pilot lamp Pilot lamp (red)Before chargingLights for 0.5 seconds. Does not light for 0.5 Blinks seconds. (off for 0.5 seconds) While chargingLights continuously Lights Charging completeLights for 0.5 seconds. Does not light for 0.5 Blinks seconds. (off for 0.5 seconds) Overheat standbyLights for 1 second. Does not light for 0.5 Blinks seconds. (off for 0.5 seconds)Battery overheated. Unable to charge. (Charging will commence when battery cools)

(2) Regarding the temperature of the rechargeable battery. The temperatures for rechargeable batteries are as shown in Table 2, and batteries that have become hot should be cooled for a while before being recharged.

○ If the battery is recharged when it is warm due to battery use or exposure to sunlight, the pilot lamp blinks. The battery will not be recharged. In such a case, let the battery cool before charging.

Table 2 Recharging ranges of batteries

PRIOR TO OPERATION

Rechargeable batteriesTemperatures at which the battery can be recharged BCL1415, BCL18150°C – 50°C
1. Setting up and checking the work environment Check if the work environment is suitable by following the precautions.

HOW TO USE

(3) Regarding time Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.

1. Confi rm the clutch dial position (See Fig. 4) The three modes of screwdriver, drill and impact drill can be switched by the position of the cap in this unit. (1) When using this unit as a screwdriver, line up the one of

Table 3 Charging time (At 20°C)

the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. (2) When using this unit as a drill, align the clutch dial drill

Charger BatteryUC18YGL2UC18YKL BCL1415, BCL1815Approx. 40 min.Approx. 60 min.

” with the triangle mark on the outer body. (3) When using this unit as an impact drill, align the cap

” with the triangle mark on the outer body. CAUTION ○ The clutch dial cannot be set between the numerals “1, 3, 5 ... 22” or the dots. ○ Do not use with the clutch dial numeral between “22” and the line at the middle of the drill mark. Doing so may cause damage (See Fig. 5). 2. Tightening torque adjustment (1) Tightening torque Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication The tightening torque diff ers depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the clutch dial, and a dots. The tightening toque at position “1” is the weakest and the torque is strongest at the highest number (See Fig. 4). (3) Adjusting the tightening torque Rotate the clutch dial and line up the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. Adjust the clutch dial in the weak or the strong torque direction according to the torque you need.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION ○ When the battery charger has been continuously used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging.

Table 1 · mark “ · hammer mark “

Page 5 of the Hitachi DV18DFL user manual — PRIOR TO OPERATION
Seite 5 · Zum Vergrößern klicken
Seite 5

CAUTION ○ The motor rotation may be locked to cease while the unit is used as drill. While operating the impact driver drill, take care not to lock the motor. ○ Too long hammering may cause the screw broken due to excessive tightening. 3. Rotation to Impact changeover (See Fig. 4) The “Rotation (Rotation only)” and “Impact (Impact + Rotation)” can be switched by aligning the drill mark “

When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates at a high speed. CAUTION ○ When changing the rotational speed with the shift knob, confi rm that the switch is off . Changing the speed while the motor is rotating will damage the gears. ○ When setting the shift knob to “HIGH” (high speed) and the position of the clutch dial is between “15” and “22”, it may happen that the clutch does not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). ○ If the motor is locked, immediately turn the power off . If the motor is locked for a while, the motor or battery may be burnt. ○ To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output.Therefore, if the tool is overloaded, the motor may stop. However, this is not the trouble but the result of protection function. In this case, release the switch of tool and eliminate the causes of overloading. 5. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.

” or the hammer mark “

” with the triangle mark on the outer body. ○ To make holes in the metal, wood or plastic, switch to “Rotation (Rotation only)”. ○ To make holes in bricks or concrete blocks, switch to “Impact (Impact + Rotation)”. CAUTION ○ If an operation which is normally performed at the “Rotation” setting is performed at “Impact” setting, the eff ect of making holes does not only increase but it may also damage the bit or other parts. ○ If it is hard to turn the clutch dial to hammer mark “

” position, turn the chuck slightly in either direction and then turn the clutch dial to hammer mark “

” position again. 4. Change rotation speed Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (See Figs. 6 and 7).

WorkSuggestions DrillingBrickUse for drilling purpose. Wood Steel Aluminum DrivingMachine screwUse the bit or socket matching the screw diameter. Wood screwUse after drilling a pilot hole.
6. How to select tightening torque and rotational speed
UseClutch Dial PositionRotating speed selection (Position of the shift knob) LOW (Low speed)HIGH (High speed) DrivingMachine screw1 – 22For 4 mm or smaller diameter screws.For 6 mm or smaller diameter screws. Wood screw1 –For 8 mm or smaller nominal diameter screws.For 4.8 mm or smaller nominal diameter screws. DrillingBrickFor 13 mm or smaller diameters.For 8 mm or smaller diameters. (DV14DFL) For 10 mm or smaller diameters. (DV18DFL) WoodFor 32 mm or smaller diameters. (DV14DFL)For 18 mm or smaller diameters. (DV14DFL) For 38 mm or smaller diameters. (DV18DFL)For 22 mm or smaller diameters. (DV18DFL) MetalFor drilling with a metal working drill bit.

Table 4 · Table 5

Page 6 of the Hitachi DV18DFL user manual — MAINTENANCE AND INSPECTION
Seite 6 · Zum Vergrößern klicken
Seite 6

CAUTION ○ The selection examples shown in Table 5 should be considered as general standard. As diff erent types of tightening screws and diff erent materials to be tightened are used in actual works proper adjustments are naturally necessary. ○ When using the impact driver drill with a machine screw at HIGH (high speed), a screw may damage or a bit may loose due to the tightning torque is too strong. Use the impact driver drill at LOW (low speed) when using a machine screw. NOTE The use of the battery BCL1415 and BCL1815 in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up. 7. Mounting and dismounting of the bit (1) After inserting a driver bit, etc. into the keyless drill chuck,

○ Do not stow bits that are of a diff erent length, gauge or dimension than the plus driver bit (65 mm long) included in the STANDARD ACCESSORIES. The bit may fall and cause bodily injury. (1) Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb (Fig. 10). (2) Installing the Bit Install the bit with steps opposite of when removing. Insert the bit so that the right and left sides are equal, as shown in Fig. 11. 13. Using the hook CAUTION ○ When using the hook, pay suffi cient attention so that the main equipment does not fall. If the tool falls, there is a risk of accident. ○ Do not attach the tip tool except phillips bit to the tool main unit when carrying the tool main unit with the hook suspended from a waist belt. Injury may result if you carry the equipment suspended from the waist belt with sharp tipped components such as drill bit attached.

fi rmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front) (See Fig. 8). ○ If the sleeve becomes loose during operation, tighten it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counter-clockwise direction as viewed from the front) (See Fig. 9). CAUTION When it is no longer possible to loosen the sleeve, use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 11 and then turn the sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. 8. Confi rm that the battery is mounted correctly 9. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise (See Fig. 9) (The and marks are provided on the body). CAUTION Always use this unit with clockwise rotation, when using it as an impact drill. 10. Switch operation ○ When the trigger switch is depressed, the tool rotates. When the trigger is released, the tool stops. ○ The rotational speed of the drill can be controlled by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE A buzzing noise is produced when the motor is about to rotate; This is only a noise, not a machine failure. 11. For drilling into brick Excessive pressing force never increases drilling speed. It will not only damage the drill tip or reduce working effi ciency, but could also shorten the service life of drill bit. Operate the impact driver drill within 10-15 kg pressing force while drilling into brick. 12. Using the bit holder CAUTION ○ Stow the bit in the specifi ed location on the tool. If the tool is used with the bit stowed improperly, the bit may fall and cause bodily injury.

The hook can be installed on the right or left side and the angle can be adjusted in 5 steps between 0° and 80°. (1) Operating the hook

(a) Pull out the hook toward you in the direction of arrow

(A) and turn in the direction of arrow (B) (Fig. 12). (b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°). Adjust the angle of the hook to the desired position for use. (2) Switching the hook position CAUTION Incomplete installation of the hook may result in bodily injury when used. (a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin (Fig. 13). (b) Remove the hook and spring (Fig. 14). (c) Install the hook and spring on the other side and

securely fasten with screw (Fig. 15). NOTE Pay attention to the spring orientation. Install the spring with larger diameter away from you (Fig. 15). (3) Using the bit holder (Hook with bit holder)

○ Installing the bit Slide the bit from the side and then insert fi rmly until the groove on the bit locks in the protruded section of the hook. ○ Removing the bit Securely hold the main unit and pull out the bit by holding the tip with your thumb (Fig. 16). CAUTION ○ Only Hitachi STANDARD ACCESSORIES phillips bit (No. 2 × 65L; Code No. 983006) may be used. Do not use other bits since they may come loose.

MAINTENANCE AND INSPECTION

1. Inspecting the tool Since use of as dull tool will degrade effi ciency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.
Page 7 of the Hitachi DV18DFL user manual — GUARANTEE
Seite 7 · Zum Vergrößern klicken
Seite 7

3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Cleaning on the outside When the impact driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 5. Storage Store the impact driver drill in a place in which the temperature is less than 40°C and out of reach of children. 6. Service parts list CAUTION Repair, modifi cation and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS Hitachi Power Tools are constantly being improved and modifi ed to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.

Information concerning airborne noise and vibration The measured values were determined according to EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 96 dB (A) Measured A-weighted sound pressure level: 85 dB (A) Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined according to EN60745.

Impact drilling into concrete: Vibration emission value ah, ID = 13.5 m/s2 Uncertainty K = 2.4 m/s2

Drilling into metal: Vibration emission value ah, D = 2.4 m/s2 Uncertainty K = 1.5 m/s2

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure. WARNING ○ The vibration emission value during actual use of the power tool can diff er from the declared value depending on the ways in which the tool is used. ○ To identify the safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Important notice on the batteries for the Hitachi cordless power tools Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modifi ed (such as disassembly and replacement of cells or other internal parts).

GUARANTEE

We guarantee Hitachi Power Tools in accordance with statutory/country specifi c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center.

Page 8 of the Hitachi DV18DFL user manual — (W/FLANGE) D3 × 16 9
Seite 8 · Zum Vergrößern klicken
Seite 8

No. Part Name Q’TY

44 SWITCH TERMINAL 1 45 INTERNAL WIRE 1 46 TERMINAL SUPPORT (A) 1 47-1 BATTERY BCL1815 2 47-2 BATTERY BCL1415 2 48 HOOK SPRING 1 49 SPECIAL SCREW (A) M5 1 501 CHARGER 1 502 PLUS DRIVER BIT (C) 1 503 CASE 1

No. Part Name Q’TY

(LEFT HAND) M6 × 25 1

2 KEYLESS CHUCK 13MM 1 3 GEAR BOX ASS’Y 1 4 CLUTCH DIAL 1 5 CLICK SPRING 1 6 O-RING 1 7 SPINDLE 1 8 SPRING (C) 1 9 RATCHET (B) 1 10 WASHER (A) 2 11 NUT 1 12 WASHER 1 13 SLIP BLOCK 2 14 STOPPER SPRING 2 15 FRONT CASE 1 16 SPRING (A) 4 17 STEEL BALL D5 4 18 RING GEAR 1 19 CARRIER 1 20 PLANET GEAR (C) 3 21 WASHER (A) 1 22 REAR CASE 1 23 TAPPING SCREW D3 × 12 4 24 SHIFT ARM 1 25 SLIDE RING GEAR 1 26 PINION (C) 1 27 PLANET GEAR (A) 6 28 PINION (B) 1 29 FIRST RING GEAR 1 30 WASHER (B) 1 31 MOTOR SPACER 1

(W/SP. WASHER) M4 × 6 2

33 HOUSING (A) (B) SET 1 34 HITACHI LABEL 1 35 HOOK ASS’Y 1 36 V-LOCK NUT M5 1 37 STRAP 1 38 PUSHING BUTTON 1 39 MOTOR 1 40 SHIFT KNOB 1

(W/FLANGE) D3 × 16 9

42 NAME PLATE 1 43 INTERNAL WIRE 1

1 FLAT HD. SCREW (A)

32 MACHINE SCREW

41 TAPPING SCREW

Item · Item

Page 9 of the Hitachi DV18DFL user manual — CERTIFICATO DI GARANZIA
Seite 9 · Zum Vergrößern klicken
Seite 9

GUARANTEE CERTIFICATE

GARANTIEBEWIJS

1 Model No. 2 Serial No. 3 Date of Purchase 4 Customer Name and Address 5 Dealer Name and Address (Please stamp dealer name and address)

1 Modelnummer 2 Serienummer 3 Datum van aankoop 4 Naam en adres van de gebruiker 5 Naam en adres van de handelaar (Stempel a.u.b. naam en adres vande de handelaar)

GARANTIESCHEIN

CERTIFICADO DE GARANTÍA

1 Modell-Nr. 2 Serien-Nr. 3 Kaufdaturn 4 Name und Anschrift des Kunden 5 Name und Anschrift des Händlers (Bitte mit Namen und Anschrift des Handlers abstempeln)

1 Número de modelo 2 Número de serie 3 Fecha de adquisición 4 Nombre y dirección del cliente 5 Nombre y dirección del distribudor (Se ruega poner el sello del distribudor con su nombre y dirección)

CERTIFICAT DE GARANTIE

CERTIFICADO DE GARANTIA

1 No. de modèle 2 No de série 3 Date d’achat 4 Nom et adresse du client 5 Nom et adresse du revendeur (Cachet portant le nom et l'adresse du revendeur)

1 Número do modelo 2 Número do série 3 Data de compra 4 Nome e morada do cliente 5 Nome e morada do distribuidor (Por favor, carímbe o nome e morada do distribuidor)

CERTIFICATO DI GARANZIA

ΠΙΣΤΟΠΟΙΗΤΙΚΟ ΕΓΓΥΗΣΗΣ

1 Modello 2 N° di serie 3 Data di acquisto 4 Nome e indirizzo dell'acquirente 5 Nome e indirizzo del rivenditore (Si prega di apporre il timbro con questi dati)

1 Αρ. Μοντέλου 2 Αύξων Αρ. 3 Ημερομηνία αγοράς 4 Όνομα και διεύθυνση πελάτη 5 Όνομα και διεύθυνση μεταπωλητή (Παρακαλούμε να χρησιμοποιηθεί σφραγίδα)

Show 4 more labels / short text on this page
English Nederlands · Deutsch Español · Français Português · Italiano Ελληνικά
Page 10 of the Hitachi DV18DFL user manual — GUARANTEE CERTIFICATE
Seite 10 · Zum Vergrößern klicken
Seite 10
Page 10 of the Hitachi DV18DFL user manual — GUARANTEE CERTIFICATE
Page 11 of the Hitachi DV18DFL user manual — GUARANTEE CERTIFICATE
Seite 11 · Zum Vergrößern klicken
Seite 11

Hitachi Power Tools Europe GmbH Siemensring 34, 47877 willich 1, F. R. Germany Tel: +49 2154 49930 Fax: +49 2154 499350 URL: http://www.hitachi-powertools.de

Hitachi Power Tools Netherlands B. V. Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040 Fax: +31 30 6067266 URL: http://www.hitachi-powertools.nl

Hitachi Power Tools (U. K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642 URL: http://www.hitachi-powertools.co.uk

Hitachi Power Tools France S. A. S. Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E. 1541, 91015 EVRY CEDEX, France Tel: +33 1 69474949 Fax: +33 1 60861416 URL: http://www.hitachi-powertools.fr

Hitachi Power Tools Belgium N.V. / S.A. Koningin Astridlaan 51, 1780 Wemmel, Belgium Tel: +32 2 460 1720 Fax: +32 2 460 2542 URL http://www.hitachi-powertools.be

Hitachi Fercad Power Tools Italia S.p.A Via Retrone 49-36077, Altavilla Vicentina (VI), Italy Tel: +39 0444 548111 Fax: +39 0444 548110 URL: http://www.hitachi-powertools.it

Hitachi Power Tools lberica, S.A. C / Migjorn, s/n, Poligono Norte, 08226 Terrassa, Barcelona, Spain Tel: +34 93 735 6722 Fax: +34 93 735 7442 URL: http://www.hitachi-powertools.es

Hitachi Power Tools Österreich GmbH Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355 Wiener Neudorf, Austria Tel: +43 2236 64673/5 Fax: +43 2236 63373

Page 12 of the Hitachi DV18DFL user manual — DICHIARAZIONE DI CONFORMITÀ CE
Seite 12 · Zum Vergrößern klicken
Seite 12

EC DECLARATION OF CONFORMITY

EC VERKLARING VAN CONFORMITEIT

We declare under our sole responsibility that this product is in conformity with standards or standardized documents EN60745, EN60335, EN55014 and EN61000 in accordance with Council Directives 2004/108/EC, 2006/95/EC and 2006/42/EC. The European Standards Manager at Hitachi Koki Europe Ltd. is authorized to compile the technical fi le.

Wij verklaren onder eigen verantwoordelijkheid dat dit produkt conform de richtlijnen of gestandardiseerde documenten EN60745, EN60335, EN55014 en EN61000 voldoet aan de eisen van EEG Bepalingen 2004/108/EC, 2006/95/EC en 2006/42/EC. De manager voor Europese normen van Hitachi Koki Europe Ltd. heeft de bevoegdheid tot het samenstellen van het technische bestand.

This declaration is applicable to the product affi xed CE marking.

Deze verklaring is van toepassing op produkten voorzien van de CE- markeringen.

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

DECLARACIÓN DE CONFORMIDAD DE LA CE

Wir erklären mit alleiniger Verantwortung, daß dieses Produkt den Standards oder standardisierten Dokumenten EN60745, EN60335, EN55014 und EN61000 in Übereinstimmung mit den Direktiven des Europarats 2004/108/EG, 2006/95/EG und 2006/42/EG entspricht. Der Manager für europäische Standards bei der Hitachi Koki Europe Ltd. ist zum Verfassen der technischen Datei befugt.

Declaramos bajo nuestra única responsabilidad que este producto está de acuerdo con las normas o con los documentos de normalización EN60745, EN60335, EN55014 y EN61000, según indican las Directrices del Consejo 2004/108/CE, 2006/95/CE y 2006/42/CE. El Jefe de Normas Europeas de Hitachi Koki Europe Ltd. está autorizado para recopilar archivos técnicos.

Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.

Esta declaración se aplica a los productos con marcas de la CE.

DECLARATION DE CONFORMITE CE

DECLARAÇÃO DE CONFORMIDADE CE

Nous déclarons sous notre seule et entière responsabilité que ce produit est conforme aux normes ou documents normalisés EN60745, EN60335, EN55014 et EN61000 en accord avec les Directives 2004/108/CE, 2006/95/CE et 2006/42/CE du Conseil. Le responsable des normes européennes d’Hitachi Koki Europe Ltd. est autorisé à compiler les données techniques.

Declaramos, sob nossa única e inteira responsabilidade, que este produto está de acordo com as normas ou documentos normativos EN60745, EN60335, EN55014 e EN61000, em conformidade com as Diretrizes 2004/108/CE, 2006/95/CE e 2006/42/CE do Conselho. O Gestor de Normas Europeias da Hitachi Koki Europe Ltd. está autorizado a compilar o fi cheiro técnico.

Cette déclaration s’applique aux produits désignés CE.

Esta declaração se aplica aos produtos designados CE.

DICHIARAZIONE DI CONFORMITÀ CE

ΕΚ ΔΗΛΩΣΗ ΕΝΑΡΜΟΝΙΣΜΟΥ

Si dichiara sotto nostra responsabilità che questo prodotto è conforme agli standard o ai documenti standardizzati EN60745, EN60335, EN55014 e EN61000 conforme alle direttive 2004/108/ CE, 2006/95/CE e 2006/42/CE del concilio. Il Responsabile delle Norme Europee di Hitachi Koki Ltd. è autorizzato a compilare la scheda tecnica.

Δηλώνουμε με απόλυτη υπευθυνότητα ότι αυτό το προιόν είναι εναρμονισμένο με τα πρότυπα ή τα έγραφα προτύπων ΕΝ60745, ΕΝ60335, ΕΝ55014 και ΕΝ61000 σε συμφωνία με τις Οδηγίες του Συμβουλίου 2004/108/ΕΚ, 2006/95/ΕΚ και 2006/42/ΕΚ. Ο υπεύθυνος για τα ευρωπαϊκά πρότυπα στην Hitachi Koki Europe Ltd. είναι εξουσιοδοτημένος να συντάσσει τον τεχνικό φάκελο.

Questa dichiarazione è applicabile ai prodotti cui sono applicati i marchi CE.

Αυτή η δήλωση ισχύει στο προιόν με το σημάδι CE.

Representative offi ce in Europe Hitachi Power Tools Europe GmbH Siemensring 34, 47877 Willich 1, F. R. Germany

Technical fi le atHitachi Koki Europe Ltd. Clonshaugh Business & Technology Park, Dublin 17, lreland
30. 4. 2010

Head offi ce in Japan Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan

K. Kato Board Director

004 Code No. C99191071 G Printed in China

Show 4 more labels / short text on this page
English Nederlands · Deutsch Español · Français Português · Italiano Ελληνικά
Quellen

Referenzen & Links

In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.

Frage zu Hitachi DV18DFL stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Hitachi DV18DFL

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Hitachi DV18DFL PDF-Anleitung

84 Seiten·5 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…