
Cordless Impact Driver Drill Akku-Schlagbohrschrauber Perceuse percussion/visseuse à batterie Trapano avvitatore a percussione a batteria Snoerloze klop-boor-schroefmachine Taladro atornillador de impacto a batería Berbequim aparafusador de impacto a bateria

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste instruzioni. Deze gebruiksaanwijzing a.u.b. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções.
Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso












c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit.
turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of
Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while
operating a power tool. Distractions can cause you to lose control.
dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards.
Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded
power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does
surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet
not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source
and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children
conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an
and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment
extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits
common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear
etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
eye protection. Protective equipment such as dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
(Original instructions)

current and overheat. It results in burn or damage to the battery. 9. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 10. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 11. Using an exhausted battery will damage the charger. 12. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 13. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury. 14. This product contains a strong permanent magnet in the motor. Observe the following precautions regarding adhering of chips to the tool and the effect of the permanent magnet on electronic devices. CAUTION Do not place the tool on a workbench or work area where metal chips are present. The chips may adhere to the tool, resulting in injury or malfunction. If chips have adhered to the tool, do not touch it. Remove the chips with a brush. Failure to do so may result in injury.
manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away
from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons.
If you use a pacemaker or other electronic medical device, do not operate or approach the tool. Operation of the electronic device may be affected. Do not use the tool in the vicinity of precision devices such as cell phones, magnetic cards or electronic memory media. Doing so may lead to misoperation, malfunction or loss of data.
1. Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. 2. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. 3. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fastener may contact hidden wiring. Cutting accessory or fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. 4. Always charge the battery at a temperature of 0 – 40°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 5. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 6. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 7. Never disassemble the rechargeable battery and charger. 8. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric
To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function. 1. When the battery power remaining runs out, the motor stops. In such a case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again. 3. If the battery is overheated under overload work, the battery power may stop. In this case, stop using the battery and let the battery cool. After that, you can use it again. Furthermore, please heed the following warning and caution.

WARNING In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions. 1. Make sure that swarf and dust do not collect on the battery. During work make sure that swarf and dust do not fall on the battery. Make sure that any swarf and dust falling on the power tool during work do not collect on the battery. Do not store an unused battery in a location exposed to swarf and dust. Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.). 2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock. 3. Do not use an apparently damaged or deformed battery. 4. Do not use the battery in reverse polarity. 5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. 6. Do not use the battery for a purpose other than those specified. 7. If the battery charging fails to complete even when a specified recharging time has elapsed, immediately stop further recharging. 8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.
9. Keep away from fire immediately when leakage or foul odor are detected. 10. Do not use in a location where strong static electricity generates. 11. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use. CAUTION 1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately. If left untreated, the liquid may cause eye-problems. 2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately. There is a possibility that this can cause skin irritation. 3. If you find rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the first time, do not use and return it to your supplier or vendor. WARNING If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing fire. When storing the lithium ion battery, obey surely the rules of following contents. Do not place conductive debris, nail and wires such as iron wire and copper wire in the storage case. To prevent shorting from occurring, load the battery in the tool or insert securely the battery cover for storing until the ventilator is not seen.
POWER TOOL

CHARGING
Before using the power tool, charge the battery as follows. 1. Connect to the power source When charging the battery from an AC power source Connect the charger’s power cord to the receptacle.
When connecting the plug of the charger to a receptacle, the pilot lamp will blink in red (At 1- second intervals). CAUTION
Do not use the electrical cord if damaged. Have it repaired immediately. When charging the battery from a DC 12V in-car power source (UC18YML2) Secure the battery charger in place in the car.
Use the strap supplied with the battery charger to fasten the battery charger in place and prevent it from moving inadvertently. (See Fig. 14) CAUTION
Do not place the battery charger or battery under the driver’s seat. Secure the battery charger in place to prevent it from moving inadvertently as this may lead to an accident.
Standard accessories are subject to change without notice. The charger and battery supplied are different depending on the set specification.
Insert the cigarette lighter connecting plug into the
cigarette lighter socket. If the plug is loose and falls out of the cigarette lighter socket, repair the socket. As the socket may be faulty, you are recommended to contact your local car dealer. Continued use of the socket may result in an accident due to overheating. 2. Insert the battery into the charger. Firmly insert the battery into the charger until the line is visible, as shown in Fig. 3, 4. Lines are not displayed on the UC18YFSL. Make sure that the battery is set firmly in place. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light up continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red. (At 1-second intervals) (See Table 1) (1) Pilot lamp indication
Optional accessories are subject to change without notice.
Drilling of brick and concrete block, etc. Driving and removing of machine screws, wood
screws, tapping screws, etc. Drilling of various metals Drilling of various woods
The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.
Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities (See Fig. 2).
Battery

(However, the cooling fan does not function when charging the battery with a DC 12V in-car power source.)
(2) Regarding the temperatures of the rechargeable
Table 2 Recharging ranges of batteries
battery The temperatures for rechargeable batteries are as shown in Table 2, and batteries that have become hot should be cooled for a while before being recharged.
Table 1

(3) Regarding recharging time
Since the built-in micro computer takes about 3
Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.
seconds to confirm that the battery being charged with UC18YML2 / UC18YRSL / UC18YFSL / UC18YGSL is taken out, wait for a minimum of 3 seconds before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged. Check the voltage of the in-car power source when
Table 3 Charging time (At 20°C)
(AC power supply / DC 12V (in-car) power supply)
the pilot lamp flickers in green (every 0.2 seconds) continuously. (UC18YML2) If the voltage is 12V or lower, it indicates that the car battery has weakened and cannot be charged. If the pilot lamp does not blink in red (every second)
even though the charger cord or cigarette lighter connecting plug is connected to the power, it indicates that the protection circuit of the charger may be activated. Remove the cord or plug from the power and then connect it again after 30 seconds or so. If this does not cause the pilot lamp to blink in red (every second), please take the charger to the Hitachi Authorized Service Center.
The recharging time may vary according to the ambient temperature and power source voltage. Especially, using a DC 12V in-car power source may require longer recharging time at high temperatures. CAUTION
When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging. 4. Disconnect the charger’s power cord from the receptacle or cigarette lighter socket 5. Hold the charger firmly and pull out the battery NOTE
Setting up and checking the work environment Check if the work environment is suitable by following the precautions.
Be sure to pull out the battery from the charger after use, and then keep it.
How to make the batteries perform longer
of the numbers “1, 3, 5 ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. (2) When using this unit as a drill, align the clutch dial drill
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.
” with the triangle mark on the outer body. (3) When using this unit as an impact drill, align the
clutch dial hammer mark “ ” with the triangle mark on the outer body. CAUTION The clutch dial cannot be set between the numerals
A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION If the battery is charged while it is heated because it
“1, 3, 5 ... 22” or the dots. Do not use with the clutch dial numeral between
“22” and the line at the middle of the drill mark. Doing so may cause damage. (See Figs. 6) 2. Tightening torque adjustment (1) Tightening torque
Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be injured. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication
has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the pilot lamp of the charger lights up green. In such a case, first let the battery cool, then start charging. When the pilot lamp flickers in red (at 0.2-seconds
The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 ... 22” on the clutch dial , and the dots. The tightening toque at position “1” is the weakest and the torque is strongest at the highest number. (See Figs. 5)
intervals), check for and take out any foreign objects in the charger’s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.
mark “

(3) Adjusting the tightening torque
Rotate the clutch dial and line up the numbers “1, 3, 5, ... 22” on the clutch dial, or the dots, with the triangle mark on the outer body. Adjust the clutch dial in the weak or the strong torque direction according to the torque you need. CAUTION The motor rotation may be locked to cease while the
unit is used as drill. While operating the driver drill, take care not to lock the motor. Too long hammering may cause the screw broken
knob, confirm that the switch is off. Changing the speed while the motor is rotating will damage the gears. When setting the shift knob to “HIGH” (high speed)
due to excessive tightening. 3. Rotation to Impact changeover (See Fig. 5) The “Rotation (Rotation only)” and “Impact (Impact + Rotation)” can be switched by aligning the drill mark “
and the position of the clutch dial is “17” or “22”, it may happen that the clutch is not engaged and that the motor is locked. In such a case, please set the shift knob to “LOW” (low speed). If the motor is locked, immediately turn the power
” or the hammer mark “ ” with the triangle mark on the outer body. To make holes in the metal, wood or plastic, switch
to “Rotation (Rotation only)”. To make holes in bricks or concrete blocks, switch to
off. If the motor is locked for a while, the motor or battery may be burnt. Be sure to turn the shift knob. 5. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 4.
“Impact (Impact + Rotation)”. CAUTION
If an operation which is normally performed at the “Rotation” setting is performed at “Impact “ setting, the effect of making holes does not only increase but it may also damage the bit or other parts.
Work Clutch dial Position Suggestion
Use for drilling purpose. Steel
Machine screw 1 – 22 Use the bit or socket matching the screw diameter. Driving
Wood screw 1 – Use after drilling a pilot hole.
Rotating speed selection (Position of the shift knob)
Use Clutch dial Position
LOW (Low speed) HIGH (High speed)
Machine screw 1 – 22 For 4 mm or smaller diameter screws. Driving
For 6 mm or smaller diameter screws.
Wood screw 1 – For 8 mm or smaller nominal diameter screws.
For 3.8 mm or smaller nominal diameter screws.
For 13 mm or smaller
For 10 mm or smaller diameters. (DV14DBEL) For 10 mm or smaller diameters. (DV18DBEL)
Brick diameters. (DV14DBEL) For 13 mm or smaller diameters. (DV18DBEL)
For 36 mm or smaller diameters.(DV14DBEL) For 38 mm or smaller diameters. (DV18DBEL)
For 18 mm or smaller diameters. (DV14DBEL) For 22 mm or smaller diameters. (DV18DBEL)
Metal For drilling with a metal working drill bit.

If the sleeve becomes loose during operation, tighten
it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit
considered as general standard. As different types of tightening screws and different materials to be tightened are used in actual works proper adjustments are naturally necessary. When using the impact driver drill with a machine
Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front), and then take out the bit etc. (See Fig. 12) NOTE
screw at HIGH (high speed), a screw may damage or a bit may loose due to the tightening torque is too strong. Use the driver drill at LOW (low speed) when using a machine screw. NOTE The use of the battery in a cold condition (below 0
If the sleeve is tightened in a state where the clip of the keyless chuck is opened to a maximum limit, a click noise may occur. This is the noise that occurs when the loosening of the keyless chuck is prevented and is not a malfunction. CAUTION
degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up. When using the unit as an impact drill, prolonged
When it is no longer possible to loosen the sleeve, use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 7 and then turn the sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. 10. Automatic spindle-lock mechanism This unit has automatic spindle-lock mechanism for quick bit changes. 11. Confirm that the battery is mounted correctly 12. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 13) (The and marks are provided on the body.) CAUTION
operation of 5 minutes or more will result in internal heat which may cause a repeated noise other than the sound normally emitted by the motor. This does not indicate a malfunction. Discontinuing use of the unit and allowing its internal temperature to cool down will eliminate the noise. For prolonged use, allow the unit to cool down periodically. 7. Using the hook The hook is used to hang up the power tool to your waist belt while working. CAUTION When using the hook, hang up the power tool firmly
not to drop accidentally. If the power tool is dropped, it may lead to an accident. When carrying the power tool with hooked to your
Always use this unit with clockwise rotation, when using it as an impact drill. 13. Switch operation When the trigger switch is depressed, the tool rotates.
waist belt, do not fit any bit to the tip of power tool. If the sharp bit such as drill is fitted to the power tool when carrying it with hooked to your waist belt, you will be injured. Install securely the hook. Unless the hook is securely
When the trigger is released, the tool stops. The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE
installed, it may cause an injury while using. (1) Removing the hook.
Remove the screws fixing the hook with Phillips screw driver. (Fig. 9) (2) Replacing the hook and tightening the screws.
A buzzing noise is produced when the motor is about to rotate; This is only a noise, not a machine failure. 14. For drilling into brick Excessive pressing force never increases drilling speed. It will not only damage the drill tip or reduce working efficiency, but could also shorten the service life of drill bit. Operate the impact driver drill within 10-15 kg pressing force while drilling into brick.
Install securely the hook in the groove of power tool and tighten the screws to fix the hook firmly. (Fig. 10) 8. Using the light Pull the trigger switch to light up the light. The light keeps on lighting while the trigger switch is being pulled. The light goes out after releasing the trigger switch. (Fig. 11) (The light automatically goes out 10 seconds after releasing the trigger switch.) CAUTION
Resting the unit after continuous work (1) The power tool is equipped with a temperature
Do not expose directly your eye to the light by looking into the light. If your eye is continuously exposed to the light, your eye will be hurt. 9. Mounting and dismounting of the bit (1) Mounting the bit
protection circuit to protect the motor. Continuous bolt-tightening work may cause the temperature of the unit to rise, activating the temperature protection circuit and automatically stopping operation. If this happens, allow the power tool to cool before resuming use. (2) After use for continuous tightening wood screw
Loosen the sleeve by turning it toward the left (in the counterclockwise direction as viewed from the front) to open the clip on the keyless chuck. After inserting a driver bit, etc., into the keyless drill chuck, and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig. 12)
works, rest the unit for 15 minutes or so when replacing the battery. The temperature of the motor, switch, etc., will rise if the work is started again immediately after battery replacement, eventually resulting in burnout.

Important notice on the batteries for the Hitachi cordless power tools Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modified (such as disassembly and replacement of cells or other internal parts).
1. Inspecting the tool Since use of a dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Cleaning on the outside When the driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics. 5. Storage Store the driver drill in a place in which the tempera ture is less than 40°C and out of reach of children. NOTE
We guarantee Hitachi Power Tools in accordance with statutory/country specific regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center.
Make sure that the battery is fully charged when stored for a long period (3 months or more). The battery with smaller capacity may not be able to be charged when used, if stored for a long period. NOTE
Information concerning airborne noise and vibration The measured values were determined according to EN60745 and declared in accordance with ISO 4871.
Storing lithium-ion batteries Make sure the lithium-ion batteries have been fully charged before storing them. Prolonged storage of batteries with a low charge may result in performance deterioration, significantly reducing battery usage time or rendering the batteries incapable of holding a charge. However, significantly reduced battery usage time may be recovered by repeatedly charging and using the batteries two to five times. If the battery usage time is extremely short despite repeated charging and use, consider the batteries dead and purchase new batteries. 6. Service parts list CAUTION
Measured A-weighted sound power level:
92 dB (A) (DV14DBEL) 92 dB (A) (DV18DBEL) Measured A-weighted sound pressure level:
81 dB (A) (DV14DBEL) 81 dB (A) (DV18DBEL) Uncertainty KpA: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined according to EN60745.
Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS
10.8 m/s2 (DV18DBEL) Uncertainty K = 1.5 m/s2
The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another. It may also be used in a preliminary assessment of exposure. WARNING The vibration emission during actual use of the power
Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.
tool can differ from the declared total value depending on the ways in which the tool is used. Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).


16 SPRING (A) 4 17 STEEL BALL D5 4
18 LOCK RING 1 19 NEEDLE ROLLER SET 4
22 CARRIER 1 23 PLANET GEAR (C) SET 3
26 SCREW SET D3×12 4 27 SHIFT ARM 1
28 SLIDE RING GEAR 1 29 PINION (C) 1
30 PLANET GEAR (A) SET 3 31 PINION (B) 1
32 PLANET GEAR (A) SET 4 33 FIRST RING GEAR 1


3 GEAR BOX ASS'Y (INCLUD.4-35) 1 4 CLUTCH DIAL 1
17 STEEL BALL D5 4 18 LOCK RING 1
23 PLANET GEAR (C) SET 3 24 WASHER (A) 1
25 REAR CASE 1 26 SCREW SET D3×12 4
27 SHIFT ARM 1 28 SLIDE RING GEAR 1
29 PINION (C) 1 30 PLANET GEAR (A) SET 3
31 PINION (B) 1 32 PLANET GEAR (A) SET 4
33 FIRST RING GEAR 1 34 WASHER (B) 1




Hitachi Power Tools Europe GmbH Siemensring 34, 47877 willich 1, F. R. Germany Tel: +49 2154 49930 Fax: +49 2154 499350 URL: http://www.hitachi-powertools.de
Hitachi Power Tools Netherlands B. V. Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040 Fax: +31 30 6067266 URL: http://www.hitachi-powertools.nl
Hitachi Power Tools (U. K.) Ltd. Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom Tel: +44 1908 660663 Fax: +44 1908 606642 URL: http://www.hitachi-powertools.co.uk
Hitachi Power Tools France S. A. S. Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E. 1541, 91015 EVRY CEDEX, France Tel: +33 1 69474949 Fax: +33 1 60861416 URL: http://www.hitachi-powertools.fr
Hitachi Power Tools Belgium N.V. / S.A. Koningin Astridlaan 51, 1780 Wemmel, Belgium Tel: +32 2 460 1720 Fax: +32 2 460 2542 URL http://www.hitachi-powertools.be
Hitachi Fercad Power Tools Italia S.p.A Via Retrone 49-36077, Altavilla Vicentina (VI), Italy Tel: +39 0444 548111 Fax: +39 0444 548110 URL: http://www.hitachi-powertools.it
Hitachi Power Tools lberica, S.A. C / Migjorn, s/n, Poligono Norte, 08226 Terrassa, Barcelona, Spain Tel: +34 93 735 6722 Fax: +34 93 735 7442 URL: http://www.hitachi-powertools.es
Hitachi Power Tools Österreich GmbH Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355 Wiener Neudorf, Austria Tel: +43 2236 64673/5 Fax: +43 2236 63373





EC VERKLARING VAN CONFORMITEIT Wij verklaren onder eigen verantwoordelijkheid dat dit product conform de richtlijnen of gestandardiseerde documenten EN60745- 1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 en EN61000 voldoet aan de eisen van bepalingen 2004/ 108/EC, 2006/95/EC en 2006/42/EC. Dit product voldoet ook aan de RoHS-richtlijn 2011/65/EU. De manager voor Europese normen van Hitachi Koki Europe Ltd. heeft de bevoegdheid tot het samenstellen van het technische bestand.
We declare under our sole responsibility that this product is in conformity with standards or standardization documents EN60745-1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335- 2-29, EN55014-1, EN55014-2 and EN61000 in accordance with Directives 2004/108/EC, 2006/95/EC and 2006/42/EC. This product also conforms to RoHS Directive 2011/65/EU. The European Standards Manager at Hitachi Koki Europe Ltd. is authorized to compile the technical file.
Deze verklaring is van toepassing op produkten voorzien van de CE- markeringen.
This declaration is applicable to the product affixed CE marking.
DECLARACIÓN DE CONFORMIDAD DE LA CE
Wir erklären mit alleiniger Verantwortung, dass dieses Produkt den Standards oder Standardisierungsdokumenten EN60745-1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 und EN61000 in Übereinstimmung mit den Direktiven 2004/108/EG, 2006/95/EG und 2006/42/EG entspricht. Dieses Produkt stimmt auch mit der RoHS-Richtlinie 2011/65/EU überein. Der Manager für europäische Standards bei der Hitachi Koki Europe Ltd. ist zum Verfassen der technischen Datei befugt.
Declaramos bajo nuestra única responsabilidad que este producto está de acuerdo con las normas o con los documentos de normalización EN60745-1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 y EN61000, según indican las Directrices 2004/108/CE, 2006/95/CE y 2006/ 42/CE. Este producto satisface también los requisitos establecidos por la Directiva 2011/65/EU (RoHS). El Jefe de Normas Europeas de Hitachi Koki Europe Ltd. está autorizado para recopilar archivos técnicos.
Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.
Esta declaración se aplica a los productos con marcas de la CE. Português
DECLARAÇÃO DE CONFORMIDADE CE
Nous déclarons sous notre seule et entière responsabilité que ce produit est conforme aux normes ou documents de normalisation EN60745-1, EN60745-2-1, EN60745-2-2, EN60335- 1, EN60335-2-29, EN55014-1, EN55014-2 et EN61000 en accord avec les Directives 2004/108/CE, 2006/95/CE et 2006/42/CE. Ce produit est aussi conforme à la Directive RoHS 2011/65/EU. Le responsable des normes européennes d’Hitachi Koki Europe Ltd. est autorisé à compiler les données techniques.
Declaramos, sob nossa única e inteira responsabilidade, que este produto está de acordo com as normas ou documentos normativos EN60745-1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335-2-29, EN55014-1, EN55014-2 e EN61000, em conformidade com as Directrizes 2004/108/CE, 2006/95/CE e 2006/42/CE. Este produto está também em conformidade com a Directiva RoHS 2011/65/EU. O Gestor de Normas Europeias da Hitachi Koki Europe Ltd. está autorizado a compilar o ficheiro técnico.
Cette déclaration s’applique aux produits désignés CE.
Esta declaração se aplica aos produtos designados CE.
DICHIARAZIONE DI CONFORMITÀ CE Dichiariamo sotto nostra responsabilità che questo prodotto è conforme agli standard o ai documenti sulla standardizzazione EN60745-1, EN60745-2-1, EN60745-2-2, EN60335-1, EN60335- 2-29, EN55014-1, EN55014-2 e EN61000 in conformità alle Direttive 2004/108/CE, 2006/95/CE e 2006/42/CE. Il prodotto è inoltre conforme alla direttiva RoHS 2011/65/EU. Il Responsabile delle Norme Europee di Hitachi Koki Ltd. è autorizzato a compilare la scheda tecnica. Questa dichiarazione è applicabile ai prodotti cui sono applicati i marchi CE.
Representative office in Europe Hitachi Power Tools Europe GmbH Siemensring 34, 47877 Willich 1, F. R. Germany
Mr. John de Loughry European Standard Manager
Head office in Japan Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan
F. Tashimo Vice-President & Director
305 Code No. C99209471 G Printed in China Hitachi Koki Co., Ltd.
In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.