DE
Hitachi logo
Offizielle Bedienungsanleitung

Hitachi DS7DF

45 Seiten·860 KB·Akkubohrschrauber·PDF·ENJA
Hitachi DS7DF
Inhaltsverzeichnis 14 Abschnitte GENERAL OPERATIONAL PRECAUTIONS · PRECAUTIONS FOR CORDLESS DRIVER DRILL · SPECIFICATIONS · POWER TOOL · … AnzeigenAusblenden
Page 1 of the Hitachi DS7DF user manual — PRECAUTIONS FOR CORDLESS DRIVER DRILL
Seite 1 · Zum Vergrößern klicken
Seite 1

GENERAL OPERATIONAL PRECAUTIONS

22. Always use the charger at the voltage specified on the nameplate. 23. Do not touch movable parts or accessories unless the power source has been disconnected. 24. Always charge the battery before use. 25. Never use a battery other than that specified. Do not connect a usual dry cell, a rechargeable battery other than that specified or a car battery to the power tool. 26. Do not use any transformer that has a booster. 27. Do not charge the battery from an engine electric generator or DC power supply. 28. Always charge indoors. Because the charger and battery heat slightly during charging, charge the battery in a place not exposed to direct sunlight; where the humidity is low and the ventilation is good. 29. Before starting to work in a high place, pay attention to the activities below to make sure there are no people below. 30. Use the exploded assembly drawing on this handling instructions only for authorized servicing. 31. If the supply cord is damaged, it must be replaced by the manufacture or its service agent or a similarly qualified person in order to avoid a hazard.

1. Keep work area clean. Cluttered areas and benches invite accidents. 2. Avoid dangerous environment. Don’t expose power tools and charger to rain. Don’t use power tools and charger in damp or wet locations. And keep work area well lit. Never use power tools and charger near flammable or explosive materials. Do not use tool and charger in presence of flammable liquids or gases. 3. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with the appliance. All visitors should be kept safe distance from work area. 4. Store idle tools and charger. When not in use, tools and charger should be stored in dry, high or locked- up place-out of reach of the children and infirm persons. Store tools and charger in a place where the temperature is less than 40°C. 5. Don’t force tool. It will do the job better and safer at the rate for which it was designed. 6. Use right tool. Don’t force small tool or attachment to do the job of a heavy duty tool. 7. Wear proper apparel. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and non-skid footwears are recommended when working outdoor. 8. Use eye protection with most tools. Also use face or dust mask if cutting operation is dusty. 9. Don’t abuse cord. Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 10. Secure work. Use clamps or a vise to hold work. It’s safer than using your hand and it frees both hands to operate tool. 11. Don’t overreach. Keep proper footing and balance at all times. 12. Maintain tools with care. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 13. When the charger is not in use, or when being maintained and inspected, disconnect its power cord from the receptacle. 14. Remove chuck wrenches and wrenches. Form habit of checking to see that wrenches are removed from tool before turning it on. 15. Avoid accidental starting. Don’t carry tool with finger on switch. 16. To avoid danger, always use only the specified charger. 17. Use only genuine HITACHI replacement parts. 18. Do not use power tools for applications other than those specified in the Handling Instructions. 19. To avoid personal injury, use only the accessories or attachment recommended in these handling instructions or in the HITACHI catalog. 20. Let only the authorized service center do the repairing. The Manufacturer will not be responsible for any damages or injuries caused by repair by the unauthorized persons or by mishandling of the tool. 21. To ensure the designed operational integrity of power tools and charger, do not remove installed covers or screws.

PRECAUTIONS FOR CORDLESS DRIVER DRILL

1. Always charge the battery at a temperature of 10 – 40°C. A temperature of less than 10°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 2. When one charging is completed, leave the charger at least 15 minutes before the next charging of battery. Do not charge more than two batteries consecutively. 3. Do not charge the battery for more than 2 hours. The battery will be fully charged in about 1 hour and charging should be stopped when 1 hour has elapsed from commencement. Disconnect the charger power cord from the receptacle. 4. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 5. Never disassemble the rechargeable battery and charger. 6. Never short-circuit the rechargeable battery. Short- circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 7. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 8. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 9. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 10. Using an exhausted battery will damage the charger. 11. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.

Page 2 of the Hitachi DS7DF user manual — APPLICATIONS
Seite 2 · Zum Vergrößern klicken
Seite 2
12. When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or come off, causing injury.

SPECIFICATIONS

POWER TOOL

ModelDS7DF No-load speed0 – 600 min–1 CapacityW ( Drilling M (ood Thickness 18mm)15 mm etal Thickness 1.6mm)Steel: 10 mm, Aluminum: 10 mm M Driving Wachine screw6 mm ood screw5.1 mm (diameter) × 32 mm (length) (Requires a pilot hole) Rechargeable batteryFEB7S: Ni-Cd 7.2 V (1.4 Ah, 6 cells)EB712S: Ni-Cd 7.2 V (1.2 Ah, 6 cells) Weight1.3 kg1.2 kg

CHARGER

BATTERY REMOVAL/INSTALLATION

ModelUC7SBUC7SD Charging voltage7.2 V Weight1.0 kg1.1 kg
1. Battery removal Hold the handle tightly and push the battery latch to remove the battery. (See Figs. 1 and 2 ) CAUTION Never short-circuit the battery. 2. Battery installation Insert the battery while observing its direction. (See Fig. 2 )

STANDARD ACCESSORIES

DS7DF1 Plus driver bit (No. 255L) 1 2 Charger (UC7SB or UC7SD) 1 3 Plastic case 1

CHARGING

Before using the driver drill, charge the battery as follows. 1. Insert the battery into the charger. Position the battery so that the nameplate faces toward the nameplate of the charger and press in the battery until it comes into contact with the bottom surface. (See Figs. 1 and 3) 2. Connect the charger power cord to the receptacle. Connecting the power cord will turn on the charger (the pilot lamp lights up). CAUTION

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

1. Battery (FEB7S, EB712S)

If the pilot lamp does not light up, pull out the power cord from the receptacle and check the battery mounting condition. (1) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 1.

Optional accessories are subject to change without notice.

APPLICATIONS

Driving and removing of machine screws, wood

screws, tapping screws, etc. Drilling of various metals. Drilling of various woods.

Page 3 of the Hitachi DS7DF user manual — PRIOR TO OPERATION
Seite 3 · Zum Vergrößern klicken
Seite 3

Table 1 Charging time (At 20°C)

HOW TO USE

Charger BatteryUC7SB / UC7SD EB712SApprox. 50 min. FEB7SApprox. 60 min.
1. Confirm the clutch dial position. (See Fig. 4) The tighthening torque of this unit can be adjusted according to the clutch dial position, at which the clutch dial is set. (1) When using this unit as a screwdriver, line up the one

of the numbers “1, 3, 5 … 22” on the clutch dial, or the white dots with the triangle mark on the outer body. (2) When using this unit as a drill, align the clutch dial

The battery charging time becomes longer when a temperature is low or the voltage of the power source is too low. When the pilot lamp does not go off even if more than two hours have elapsed after starting of the charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER. CAUTION

” with the triangle mark on the outer body. CAUTION The clutch dial cannot be set between the numbers

“1, 3, 5 … 22” or the white dots. Do not use with the clutch dial numeral between “22”

If the battery is heated due to direct sunlight, etc., just after operation, the charger pilot lamp may not light up. At that time, cool the battery first, then start charging. 3. Disconnect the charger power cord from the receptacle. 4. Hold the charger tight and pull out the battery.

and the white line at the middle of the drill mark. Doing so may cause damage. (See Fig. 5) 2. Tightening torque adjustment (1) Tightening torque

Tightening torque should correspond in its intensity to the screw diameter. When too strong torque is used, the screw head may be broken or be damaged. Be sure to adjust the clutch dial position according to the screw diameter. (2) Tightening torque indication

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2-3 times.

The tightening torque differs depending on the type of screw and the material being tightened. The unit indicates the tightening torque with the numbers “1, 3, 5 … 22” on the cluch dial, and the white dots. The tightening torque at position “1” is the weakest and the torque is strongest at the highest number. (See Fig. 4) (3) Adjusting the tightening torque

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

Rotate the clutch dial and align the numbers “1, 3, 5 … 22” on the clutch dial, or the white dots with the triangle mark on the outer body. Adjust the clutch dial in the weak or the strong torque direction according to the torque you need. CAUTION The motor rotation may be locked to cease while the

exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter. (2) Avoid recharging at high temperatures.

unit is used as a drill. While operating the driver drill, take care not to lock the motor. Too long hammering may cause the screw broken due

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

to excessive tightening force. 3. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 2.

PRIOR TO OPERATION

1. Setting up and checking the work environment Check if the work environment is suitable by following the precautions.
WorkSuggestions DrillingWoodUse for drilling purpose. Steel Aluminum DrivingMachine screwUse the bit or socket matching the screw diameter. Wood screwUse after drilling a pilot hole.

drill mark “ · Table 2

Page 4 of the Hitachi DS7DF user manual — MAINTENANCE AND INSPECTION
Seite 4 · Zum Vergrößern klicken
Seite 4
4. Mounting and dismounting of the bit (1) After inserting a driver bit, etc. into the keyless drill

CAUTION:

Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATIONS:

chuck, firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig. 6) If the sleeve becomes loose during operation, tighten

it further. The tightening force becomes stronger when the sleeve is tightened additionally. (2) Dismounting the bit

Firmly grasp the ring and loosen the sleeve by turning it toward the left (in the counter-clockwise direction as viewed from the front). (See Fig. 6) CAUTION When it is no longer possible to loosen the sleeve,

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

use a vise or similar instrument to secure the bit. Set the clutch mode between 1 and 10 and then turn the sleeve to the loose side (left side) while operating the clutch. It should be easy now to loosen the sleeve. NOTE There is a plus driver bit on side of the main unit.

The bit can be removed by pulling it forward. After using the bit, make sure to firmly attach it to the main body again. 5. Confirm that the battery is mounted correctly. 6. Check the rotation direction. The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L- side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 7) (The

Blue: – Neutral Brown: – Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except United Kingdom.

marks are provided on the body.) 7. Switch operation When the trigger switch is pulled, the tool rotates. When the trigger is released, the tool stops. The rotational speed of the drill can be controlled by

varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger switch is pulled more. NOTE A peep sound may be produced when the motor is

about to rotate; This is only a noise, not a machine failure.

MAINTENANCE AND INSPECTION

1. Inspecting the tool Since use of as dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Cleaning on the outside When the driver drill is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, as they melt plastics. 4. Storage Store the driver drill in a place in which the tempera ture is less than 40°C and out of reach of children. 5. Service parts list A : Item No. B : Code No. C : No. Used D : Remarks

Information concerning airborne noise and vibration The measure values were determined according to EN50144.

The typical A-weighted sound pressure level does not exceed 70 dB (A). Wear ear protection.

The typical weighted root mean square acceleration value: 0.4 m/s2

and

Frage zu Hitachi DS7DF stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Hitachi DS7DF

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Hitachi DS7DF PDF-Anleitung

45 Seiten·860 KB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…