DE
Hitachi logo
Offizielle Bedienungsanleitung

Hitachi DH24PB-2

82 Seiten·2.1 MB·Akkubohrschrauber·PDF·ENJA
Hitachi DH24PB-2
Inhaltsverzeichnis 18 Abschnitte DH 24PA • DH 24PB · P U · GENERAL OPERATIONAL PRECAUTIONS · PRECAUTIONS ON USING ROTARY HAMMER · … AnzeigenAusblenden
Page 1 of the Hitachi DH24PB-2 user manual — DH 24PA • DH 24PB
Seite 1 · Zum Vergrößern klicken
Seite 1

Rotary Hammer Bohrhammer Marteau perforateur Martello perforatore Boorhamer Martillo perforador Martelo perfurador Συρδράπαν περιστρικ

DH 24PA • DH 24PB

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste istruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções. ∆ιαάστε πρ σεκτικά και καταν ήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions Bedienungsanleitung Mode d’emploi Istruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso δηγίες ειρισµ ύ

Page 2 of the Hitachi DH24PB-2 user manual — DH 24PA • DH 24PB
Seite 2 · Zum Vergrößern klicken
Seite 2
Hitachi DH24PB-2 — DH 24PA • DH 24PB diagram (page 2)
Abb. 1
Hitachi DH24PB-2 — DH 24PA • DH 24PB diagram (page 2)
Abb. 2
Hitachi DH24PB-2 — DH 24PA • DH 24PB diagram (page 2)
Abb. 3
Page 3 of the Hitachi DH24PB-2 user manual — DH 24PA • DH 24PB
Seite 3 · Zum Vergrößern klicken
Seite 3
Hitachi DH24PB-2 — DH 24PA • DH 24PB diagram (page 3)
Abb. 4
Hitachi DH24PB-2 — DH 24PA • DH 24PB diagram (page 3)
Abb. 5
Page 4 of the Hitachi DH24PB-2 user manual — W
Seite 4 · Zum Vergrößern klicken
Seite 4
Hitachi DH24PB-2 — P U diagram (page 4)
Abb. 6
Hitachi DH24PB-2 — P U diagram (page 4)
Abb. 7

P U

T

aQ R5mm41 S–72

W

EnglishDeutschFrançaisItaliano 1Drill bitBohrerForet de perçagePunta del trapano 2Part of SDS-plus shankTeii des SDS-plus SchaftesElément de la tige SDS plusParte dell'asta SDS plus 3Front capVordere AbdeckungCapuchon avantProtezione davanti 4GripSpannbackeAttache coulissantePresa davanti 5Dust cupStaubschaleGodet à poussièreContenitore a polvere 6Dust collector (B)Staubfänger (B)Collecteur à poussière (B)Camera a polvere (B) 7LeverHebelLevierLeva 8Change leverWahlhebelSélecteurLeva di selezione 9Drill chuckBohrfutterMandrin porte-foretMandrino 0Chuck adapterBohrfutteradapterRaccord de mandrinAdattatore per mandrino AChuck adapter (D)Bohrfutteradapter (D)Raccord (D) de mandrinAdattatore (D) per mandrino BBitBohrerspitzeMèchePunta CSocketFassungPrisePresa DSide handleHandgriffPoignée lateraleLaterale EDepth gaugeTiefenmesserJauge de profondeurCalibro profondità FMounting holeBefestigungsöffnungOrifice de montageForo d’inserimento della bacchetta di arresto GTape shank adapterKegelschaftadapterRaccord de queue coniqueAdattatore per gambo conico HCotterDornClavetteCoppiglia IRestAuflageSupportAppoggio JCore bitBohrkroneCouronneCorona KCore bit shankBohrkronenzapfenQueue de couronneGambo della corona LThreadGewindeFiletageFilettatura MCenter pinMittelstiftGoujon centralPunta della corona NGuide plateFührungsplattePlaque de guidagePiastra guida OCore bit tipBohrkronenspitzeBout de couronnePunta della corona PWear limitVerschleißgrenzeLimite d’usureLimite di usura QNo. of carbon brushNr. der KohlebürsteNo. de balai en carboneN. della spazzola di carbone RUsual carbon brushGewöhnliche KohlebürsteBalai en carbone ordinaireSpazzola di carbonecomune SAuto-stop carbon brushAuto-Stop KohlebürsteBalai en carbone à arrêtautomatiqueSpazzolz di carbone ad arresto automatico TBrush holderBürstenhalterSupport de balaiPortaspazzola UCarbon brushKohlebürsteBalai en carboneSpazzola di carbone VInternal wiringInterne VerdrahtungCircuiterie intérieurCavi interni WSwitchSchalterInterrupteurInterruttore

a

Page 5 of the Hitachi DH24PB-2 user manual — P U
Seite 5 · Zum Vergrößern klicken
Seite 5
NederlandsEspañolPortuguêsΕλληνικά 1BoorstukBrocaBrocaΛεπίδα τρυπανιύ 2Onderdeel van SDS Plus schachtParte delSDS más vástagoCabo de peça SDS-plusΤµήµα τυ SDS-plus στελέυς 3VoorkapCubierta frontalTampa da frenteΜπρστιν περίληµα 4GreepSujetadorMordenteΛαή 5StofvangkapCapa de polvoReceptáculo para poeiraΚύπελλ σκνης 6Stofverzamelaar (B)Colector de polvo (B)Coletor de poeira (B)Συλλέκτης σκνης (Β) 7HendelPalancaAlavancaΜλς 8KeuzeschakelaarPalanquita selectoraSeletorΜλς αλλαγής 9BoorkopPortabrocasMandrilΣ!ικτήρας τρυπανιύ 0BoorkopadaptorAdaptador del portabrocasAdaptador do mandrilΠρσαρµγέας σ!ικτήρα ABoorkopadaptor (D)Adaptador (D) del portabrocasAdaptador do mandril (D)Πρσαρµγέας σ!ικτήρα (D) BBoorstukBrocaPalhetãoΛεπίδα CAansluithulsCuboEncaixeΥπδή DZijgreepMango lateralEmpunhadura lateralΠλευρική λαή EDiepte-maatlatCalibre de profundidadSondaΜετρητής άθυς FMontagegatAgujero de montajeOrifício de montagemΤρύπα στερέωσης GVernauwde schachtadaptorAdaptador de la espiga ahusadaAdaptador de cabo cônicoΚωνικς πρσαρµγέας στελέυς HCotterChavetaCavilhaΚ!της ISteunApoyoSuporteΣτήριγµα JKernstukBarrena tubularCoroaΚυλινδρικ κπτικ τµήµα KKernstukschachtEspiga de la barrena tubularCabo de coroaΆ'νας κυλινδρικύ κπτικύ τµήµατς LSchroefdraadRoscaRoscaΣπείρωµα MMiddenpinPasador centralPino centralΚεντρική περνη NPasplaatjePlaca guíaPlaca-guia*δηγητική πλάκα OTop van kernstukPunta de barrena tubularCabo da coroaΆκρη κυλινδρικύ κπτικύ τµήµατς PSlijtagegrensLímite de desgasteLimite de desgaste+ρι !θράς QNr. van koolborstelNo. de escobilla de carbónNº da escova de carvãoΑρ. καρυνακίων RNormale koolborstelEscobilla de carbón usualEscova de carvão normalΣυνηθισµέν καρυνάκι SAuto-stop koolborstelEscobilla de carbón de paradaEscova de carvão de parada automáticaΚαρυνάκι αυτµατης διακπής TBorstelhouderPortaescobillaSuporte de escovaΣυγκρατητής καρυνακιύ UKoolborstelEscobilla de carbónEscova de carvãoΚαρυνάκι Vnterne bedradingCableado internoCircuito internoΕσωτερική καλωδίωση WSchakelaarConmutadorInterruptor∆ιακπτης
Page 6 of the Hitachi DH24PB-2 user manual — PRECAUTIONS ON USING ROTARY HAMMER
Seite 6 · Zum Vergrößern klicken
Seite 6

17. Avoid unintentional starting. Do not carry a plugged- in tool with a finger on the switch. Ensure switch is off when plugging in. 18. Use outdoor extension leads. When tool is used outdoors, use only extension cords intended for outdoor use. 19. Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired. 20. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this handling instructions. Have defective switches replaced by an authorized service center. Do not use the tool if the switch does not turn it on and off. 21. Warning The use of any accessory or attachment, other than those recommended in this handling instructions, may present a risk of personal injury. 22. Have your tool repaired by a qualified person. This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts. Otherwise this may result in considerable danger to the user.

GENERAL OPERATIONAL PRECAUTIONS

WARNING! When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following. Read all these instructions before operating this product and save these instructions. For safe operations: 1. Keep work area clean. Cluttered areas and benches invite injuries. 2. Consider work area environment. Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk to cause fire or explosion. 3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces. (e.g. pipes, radiators, ranges, refrigerators). 4. Keep children and infirm persons away. Do not let visitors touch the tool or extension cord. All visitors should be kept away from work area. 5. Store idle tools. When not in use, tools should be stored in a dry, high or locked up place, out of reach of children and infirm persons. 6. Do not force the tool. It will do the job better and safer at the rate for which it was intended. 7. Use the right tool. Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saw to cut tree limbs or logs. 8. Dress properly. Do not wear loose clothing or jewelry, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors. Wear protecting hair covering to contain long hair. 9. Use eye protection. Also use face or dust mask if the cutting operation is dusty. 10. Connect dust extraction equipment. If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used. 11. Do not abuse the cord. Never carry the tool by the cord or yank it to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges. 12. Secure work. Use clamps or a vise to hold the work. It is safer than using your hand and it frees both hands to operate tool. 13. Do not overreach. Keep proper footing and balance at all times. 14. Maintain tools with care. Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cords periodically and if damaged, have it repaired by authorized service center. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean, and free from oil and grease. 15. Disconnect tools. When not in use, before servicing, and when changing accessories such as blades, bits and cutters. 16. Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.

PRECAUTIONS ON USING ROTARY HAMMER

1. Wear earplugs to protect your ears during operation. 2. Do not touch the bit during or immediately after operation. The bit becomes very hot during operation and could cause serious burns. 3. Before starting to break, chip or drill into a wall, floor or ceiling, thoroughly confirm that such items as electric cables or conduits are not buried inside. 4. Always hold the body handle and side handle of the power tool firmly. Otherwise the counterforce produced may result in inaccurate and even dangerous operation.

Page 7 of the Hitachi DH24PB-2 user manual — OPTIONAL ACCESSORIES (sold separately)
Seite 7 · Zum Vergrößern klicken
Seite 7
SPECIFICATIONS ModelDH24PADH24PB Voltage (by areas)*(110V, 115V, 120V, 127V, 220V, 230V, 240V) Power Input620W* No-load speed1050/min.0 – 1050/min. Full-load impact rate4400/min.0 – 4400/min. Capacity: concrete steel wood3.4 – 24 mm 13 mm 32 mm Weight (without cord and side handle)2.3 kg
Hitachi DH24PB-2 — STANDARD ACCESSORIES diagram (page 7)
Abb. 8

* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Case (Molded plastic) 1 (2) Side handle 1 (3) Depth gauge 1

Standard accessories are subject to change without notice.

OPTIONAL ACCESSORIES (sold separately)

1. Drilling anchor holes (rotation + striking) Drill bit (Slender shaft)
Hitachi DH24PB-2 — OPTIONAL ACCESSORIES (sold separately) diagram (page 7)
Abb. 9 · OPTIONAL ACCESSORIES (sold separately)

Adapter for slender shaft (SDS-plus shank) Drill bit (Slender shaft)

Drill bit (slender shaft) Outer diameterEffective lengthOverall length 3.4 mm45 mm90 mm 3.5 mm

Drill bit (Taper shank) and taper shank adapter

Hitachi DH24PB-2 — OPTIONAL ACCESSORIES (sold separately) diagram (page 7)
Abb. 10 · OPTIONAL ACCESSORIES (sold separately)

Drill bit (Taper shank) Taper shank adapter (SDS-plus shank)

Taper modeApplicable drill bit Morse taper (No.1)Drill bit (taper shank)11.0 ~ 17.5 mm Morse taper (No.2)Drill bit (taper shank)21.5 mm A-taperTaper shank adapter formed A-taper or B-taper is provided as an optional accessory, but the drill bit for it is not provided. B-taper
Hitachi DH24PB-2 — OPTIONAL ACCESSORIES (sold separately) diagram (page 7)
Abb. 11 · OPTIONAL ACCESSORIES (sold separately)

11.0 mm 12.3 mm 12.7 mm 14.3 mm 14.5 mm 17.5 mm 21.5 mm

Cotter · Outer diameter

Page 8 of the Hitachi DH24PB-2 user manual — W1/4” W5/16”
Seite 8 · Zum Vergrößern klicken
Seite 8

13 mm rotary hammer chuck

For drilling operations when using a straight shank bit for impact drilling with a rotary hammer.

Hitachi DH24PB-2 — ( ) Straight shank bit for impact drill diagram (page 8)
Abb. 12 · ( ) Straight shank bit for impact drill
Hitachi DH24PB-2 — ( ) Straight shank bit for impact drill diagram (page 8)
Abb. 13 · ( ) Straight shank bit for impact drill

( ) Straight shank bit for impact drill

13 mm Rotary hammer chuck (SDS-plus shank)

2. Anchor setting Anchor setting adapter (for rotary hammer)
Hitachi DH24PB-2 — ( ) Straight shank bit for impact drill diagram (page 8)
Abb. 14 · ( ) Straight shank bit for impact drill

Anchor setting adapter (SDS-plus shank) (for rotary hammer) Overall length: 160, 260 mm

W1/4” W5/16”

W3/8”

Anchor setting adapter (for manual hammer)

Hitachi DH24PB-2 — W1/4” W5/16” diagram (page 8)
Abb. 15

W1/4” W5/16”

W3/8” W1/2” W5/8”

Anchor setting adapter (for manual Hammer)

3. Large hole boring (rotation + striking) Center pin, core bit, core bit shank and guide plate.
Hitachi DH24PB-2 — W1/4” W5/16” diagram (page 8)
Abb. 16

(Guide plate) Center pin Core bit Core bit shank (SDS-plus shank)

Center pinCore bit (outer diameter)Core bit shank –(A)25 mm 29 mmCore bit shank (A) Center pin (A)32 mm 35 mm 38 mm Center pin (B)(B)45 mm 50 mmCore bit shank (B) Do not use core bits with outer diameter of 25 mm and 29 mm.with guide plate (The guide plate is not equipped with core bits with outer diameter of 25 mm and 29 mm.)

Chuck wrench · Anchor size · Anchor size

Page 9 of the Hitachi DH24PB-2 user manual — ( )
Seite 9 · Zum Vergrößern klicken
Seite 9
4. Crushing operation (rotation + striking)

Bull point (Round type only) (SDS-plus shank)

Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 17
Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 18
Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 19
5. Bolt placing operation with Chemical Anchor. (rotation + striking)
Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 20

( )

Standard socket on the market

(SDS-plus shank) 12.7 mm Chemical Anchor Adapter 19 mm Chemical Anchor Adapter

6. Drilling holes and driving screws (rotation only) Drill chuck, chuck adapter (G), special screw and chuck wrench
Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 21
Hitachi DH24PB-2 — ( ) diagram (page 9)
Abb. 22

Drill chuck (13 VLR) Special screw

Chuck adapter (G) (SDS-plus shank)

Chuck wrench

Page 10 of the Hitachi DH24PB-2 user manual — ( )
Seite 10 · Zum Vergrößern klicken
Seite 10
7. Drilling holes (rotation only)
Hitachi DH24PB-2 — ( ) diagram (page 10)
Abb. 23
Hitachi DH24PB-2 — ( ) diagram (page 10)
Abb. 24

Drill chuck (13 VLA)

Chuck adapter (D) (SDS-plus shank)

13 mm drill chuck ass’y (includes chuck wrench) and chuck (for drilling in steel or wood).

8. Driving Screws (rotation only)
Hitachi DH24PB-2 — ( ) diagram (page 10)
Abb. 25
9. Dust cup, Dust collector (B)
10. Hammer grease A 500 g (in a can) 70 g (in a green tube) 30 g (in a green tube)
Hitachi DH24PB-2 — ( ) diagram (page 10)
Abb. 26

Dust cup Dust collector (B)

Optional accessories are subject to change without notice.

Chuck wrench

Page 11 of the Hitachi DH24PB-2 user manual — HOW TO USE
Seite 11 · Zum Vergrößern klicken
Seite 11

please use dust collector (B) by attaching to drill bits which have 166 mm, 160 mm, and 110 mm overall length.) Dump particles after every two or three holes when

APPLICATIONS

Rotation and striking function Drilling anchor holes Drilling holes in concrete Drilling holes in tile Rotation only function Drilling in steel or wood

drilling. Please replace the drill bit after removing dust

collector (B). 6. Selecting the driver bit Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws. 7. Confirm the direction of bit rotation (Fig. 4) The bit rotates clociwise (viewed from the rear side) by pushing the R-side of the reversing switch lever. The L-side of the lever is pushed to turn the bit counterclockwise.

(with optional accessories) Tightening machine screws, wood screws

PRIOR TO OPERATION

1. Power source Ensure that the power source to be utilized conforms to the power requirements specified on the product nameplate. 2. Power switch Ensure that the power switch is in the OFF position. If the plug is connected to a power receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident. 3. Extension cord When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable. 4. Mounting the drill bit (Fig. 1) (1) To attach a drill bit (SDS-plus shank), fully pull the

HOW TO USE

CAUTION:

To prevent accidents, make sure to turn the switch off and disconnect the plug from the receptacle when the drill pits and other various parts are installed or removed. The power switch should also be turned off during a work break and after work. 1. Switch operation (1) DH24PA

By pulling the trigger switch and depressing the stopper, the switch is held in the ON position for continuous operation. To turn the drill OFF, pull the trigger switch again and release. (2) DH24PB

grip in the direction of the arrow as shown in Fig. 1 and insert the drill bit as far as it will go while manually turning. (2) By releasing the grip, the drill bit will be secured. (3) To remove the drill bit, fully pull the grip in the

The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. Continuous operation may be attained by pulling the trigger switch and depressing the stopper. To turn the switch OFF, pull the trigger switch again to disengage the stopper, and release the trigger switch to its original position. 2. Rotation + striking This rotary hammer can be set to rotation and striking mode by turning the change lever fully counterclockwise to the

direction of the arrow and pull out the drill bit. 5. Installation of dust cup or dust collector (B) (Optional accessories) (Fig. 2, Fig. 3) When using a rotary hammer for upward drilling operations attach a dust cup or dust collector (B) to collect dust or particles for easy operation. Installing the dust cup

Use the dust cup by attaching to the drill bit as shown in Fig. 2. When using a bit which has big diameter, enlarge the center hole of the dust cup with this rotary hammer. Installing dust collector (B)

mark. (Fig. 5) (1) Mount the drill bit. (2) Pull the trigger switch after applying the drill bit tip to

the drilling position. (Fig. 6) (3) Pushing the rotary hammer forcibly is not necessary

When using dust collector (B), insert dust collector (B) from the tip of the bit by aligning it to the groove on the grip. (Fig. 3) CAUTION: The dust cup and dust collector (B) are for exclusive

at all. Pushing slightly so that drill dust comes out gradually is sufficient. CAUTION:

When the drill bit touches construction iron bar, the bit will stop immediately and the rotary hammer will react to revolve. Therefore grip the side handle and handle tightly as shown in Fig. 6. 3. Rotation only The hammer drill can be set to rotation only mode by rotating the change lever fully clockwise to the

use of concrete drilling work. Do not use them for wood or metal drilling work. Insert dust collector (B) completely into the chuck

part of the main unit. When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing the dust cup on the concrete surface. (When using dust collector (B) attached to a drill bit that has more than 190 mm of overall length, dust collector (B) cannot touch the concrete surface and will rotate. Therefore

mark. (Fig. 7) To drill wood or metal material using the drill chuck and chuck adapter (optional accessories), proceed as follows. Installing drill chuck and chuck adapter: (Fig. 8)

(with optional accessories)

Page 12 of the Hitachi DH24PB-2 user manual — LUBRICATION
Seite 12 · Zum Vergrößern klicken
Seite 12

(1) Attach the drill chuck to the chuck adapter. (2) The part of the SDS-plus shank is the same as the

(2) Mount the drill bit (taper shank) to the taper shank

adapter. (Fig. 11) (3) Turn the switch ON, and drill a hole in prescribed

drill bit. Therefore, refer to the item of “Mounting the drill bit” for attaching it. CAUTION: Application of force more than necessary will not

depth. (4) To remove the drill bit (taper shank), insert the cotter

into the slot of the taper shank adapter and strike the head of the cotter with a hammer supporting on a rests. (Fig. 12)

only expedite the work, but will deteriorate the tip edge of the drill bit and reduce the service life of the rotary hammer in addition. Drill bits may snap off while withdrawing the rotary

HOW TO USE THE CORE BIT (FOR LIGHT LOAD)

hammer from the drilled hole. For withdrawing, it is important to use a pushing motion. Do not attempt to drill anchor holes or holes in

When boring penerating large holes use the core bit (for light loads). At that time use with the center pin and the core bit shank provided as optional accessories. 1. Mounting CAUTION:

concrete with the machine set in the rotation only function. Do not attempt to use the rotary hammer in the

rotation and striking function with the drill chuck and chuck adapter attached. This would seriously shorten the service life of every component of the machine. 4. When driving machine screws (Fig. 9) First, insert the bit into the socket in the end of chuck adapter (D). Next, mount chuck adapter (D) on the main unit using procedures described in 4 (1), (2), (3), put the tip of the bit in the slots in the head of the screw, grasp the main unit and tighten the screw. CAUTION: Exercise care not to excessively prolong driving time,

Be sure to turn power OFF and disconnect the plug from the receptacle. (1) Mount the core bit to the core bit shank. (Fig. 13)

Lubricate the thread of the core bit shank to facilitate disassembly. (2) Mount the core bit to the rotary hammer (Fig. 14) (3) Insert the center pin into the guide plate until it stops. (4) Engage the guide plate with the core bit, and turn the

guide plate to the left or the right so that it does not fall even if it faces downward. (Fig. 15) 2. How to bore (Fig. 16) (1) Connect the plug to the power source. (2) A spring is installed in the center pin.

otherwise, the screws may be damaged by excessive force. Apply the rotary hammer perpendicularly to the screw

Push it lightly to the wall or the floor straight. Connect the core bit tip flush to the surface and start operating. (3) When boring about 5 mm in depth the position of the

head when driving the screw; otherwise, the screw head or bit will be damaged, or driving force will not be fully transferred to the screw. Do not attempt to use the rotary hammer in the

hole will be established. Bore after that removing the center pin and the guide plate from core bit. (4) Application of excessive force will not only expedite

rotation and striking function with the chuck adapter and bit attached. 5. When driving wood screws (Fig. 9) (1) Selecting a suitable driver bit

the work, but will deteriorate the tip edge of the drill bit, resulting in reduced service life of the rotary hammer. CAUTION:

Employ plus-head screws, if possible, since the driver bit easily slips off the heads of minus-head screws. (2) Driving in wood screws Prior to driving in wood screws, make pilot holes

When removing the center pin and the guide plate, turn OFF the switch and disconnect the plug from the receptacle. 3. Dismounting (Fig. 17) Remove the core bit shank from the rotary hammer and strike the head of the core bit shank strongly two or three times with a hammer holding the core bit, then the thread becomes loose and the core bit can be removed.

suitable for them in the wooden board. Apply the bit to the screw head grooves and gently drive the screws into the holes. After rotating the rotary hammer at low speed for a

while until the wood screw is partly driven into the wood, squeeze the trigger more strongly to obtain the optimum driving force. CAUTION:

Exercise care in preparing a pilot hole suitable for the wood screw taking the hardness of the wood into consideration. Should the hole be excessively small or shallow, requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged. 6. Using depth gauge (Fig. 10) (1) Loosen the knob on the side handle, and insert the

LUBRICATION

Low viscosity grease is applied to this rotary hammer so that it can be used for a long period without replacing the grease. Please contact the nearest service center for grease replacement when any grease is leaking form loosened screw. Further use of the rotary hammer with lock off grease will cause the machine to seize up reduce the service life. CAUTION:

depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position according to the

A special grease is used with this machine, therefore, the normal performance of the machine may be badly affected by use of other grease. Please be sure to let one of our service agents undertake replacement of the grease.

depth of the hole and thighten the knob securely. 7. How to use the drill bit (taper shank) and the taper shank adapter (1) Mount the taper shank adapter to the rotary hammer.

(Fig. 11)

Page 13 of the Hitachi DH24PB-2 user manual — CAUTION:
Seite 13 · Zum Vergrößern klicken
Seite 13

CAUTION:

MAINTENANCE AND INSPECTION

Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed. MODIFICATION:

1. Inspecting the drill bits Since use of a dull tool will cause motor malfunctioning and degraded efficiency, replace the drill bit with new ones or resharpen them without delay when abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very ”heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Inspecting the carbon brushes (Fig. 18) The motor employs carbon brushes which are consumable parts. When they become worn to or near “wear limit”, it could result in motor trouble. When an auto-stop carbon brush is equipped, the motor will stop automatically. At that time, replace both carbon brushes with new ones which have the same carbon brush numbers shown in Fig. 18. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders. 5. Replacing a carbon brush (Fig. 19) Disassembling (1) Loosen the three screws on the handle cover, and

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts (i.e. code numbers and/or design) may be changed without prior notice.

Blue: -Neutral Brown: -Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE: This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markets except The United Kingdom.

remove the handle cover. (2) Lift out the brush holder together with the carbon

brush, while being very careful not to forcibly pull the lead wires within the brush holder. (3) Withdraw the brush terminal, and remove the carbon

brush from the brush holder. Reassembling (1) Place a new carbon brush into the brush holder, and

connect the brush terminal to the carbon brush. (2) Return the brush holder and other parts to their

original positions, as illustrated in Fig. 19. (3) Place the lead wire in the specified position. Be very

careful not to allow the lead wire to contact the armature or rotating parts of the motor. (4) Replace the handle cover, while being careful to

Information concerning airborne noise and vibration The measured values were determined according to EN50144.

ensure it does not pinch the lead wire, and secure it firmly with the three screws. CAUTION:

The typical A-weighted sound pressure level: 90 dB (A). The typical sound power level: 103 dB (A).

Should the lead wire be pinched by the handle cover or come in contact with the armature or rotating parts of the motor, a serious danger of electric shock to the operator will be created. Excercise extreme caution in disassembling and reassembling the motor, following the above procedures exactly. Do not attempt to disassemble any parts other than those necessary to effect replacement of the carbon brush. 6. Service parts list A: Item No. B: Code No. C: No. Used D: Remarks

Wear ear protection.

The typical weighted root mean square acceleration value: 8.0 m/s2.

Frage zu Hitachi DH24PB-2 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Hitachi DH24PB-2

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Hitachi DH24PB-2 PDF-Anleitung

82 Seiten·2.1 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…