DE
Hitachi logo
Offizielle Bedienungsanleitung

Hitachi DH18DSL

84 Seiten·1.3 MB·Akkubohrschrauber·PDF·ENJA
Hitachi DH18DSL
Inhaltsverzeichnis 3 Abschnitte 〰ㅃ潶敲䙟䑈ㄴ䑓䱟坅 · 〰呡扬敟䑈ㄴ䑓䱟坅 · 〱䕮束䑈ㄴ䑓䱟坅 AnzeigenAusblenden
Page 1 of the Hitachi DH18DSL user manual — Handling instructions
Seite 1 · Zum Vergrößern klicken
Seite 1

Cordless Rotary Hammer Akku-bohrhammer Marteau perforateur à batterie Martello perforatore a batteria Snoerloze boorhamer Martillo perforador a batería Martelo perfurador a bateria

DH 14DSL • DH 18DSL

Hitachi DH18DSL — DH 14DSL • DH 18DSL diagram (page 1)
Abb. 1

Read through carefully and understand these instructions before use. Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen. Lire soigneusement et bien assimiler ces instructions avant usage. Prima dell’uso leggere attentamente e comprendere queste instruzioni. Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen. Leer cuidadosamente y comprender estas instrucciones antes del uso. Antes de usar, leia com cuidado para assimilar estas instruções.

Handling instructions

Bedienungsanleitung Mode d’emploi Instruzioni per l’uso Gebruiksaanwijzing Instrucciones de manejo Instruções de uso

Page 2 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 2 · Zum Vergrößern klicken
Seite 2
Hitachi DH18DSL — 〰呡扬敟䑈ㄴ䑓䱟坅 diagram (page 2)
Abb. 2
Hitachi DH18DSL — 〰呡扬敟䑈ㄴ䑓䱟坅 diagram (page 2)
Abb. 3
Hitachi DH18DSL — 〰呡扬敟䑈ㄴ䑓䱟坅 diagram (page 2)
Abb. 4
Page 3 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 3 · Zum Vergrößern klicken
Seite 3
EnglishDeutschFrançaisItaliano 1Rechargeable batteryBatterieBatterie rechargeableBatteria ricaricabile 2LatchSchnapperLoquetFermo 3Battery coverBatterieabdeckungCouvercle de pileCoperchio per la batteria 4TerminalsAnschlüsseBornesTerminali 5Ventilation holesBelüftungslöcherOrifices de ventilationFori di ventilazione 6PushDrückenPousserSpingere 7HandleHandgriffPoignéeImpugnature 8Pull outHerausziehenTirer vers l’extérieurEstrarre 9InsertEinsetzenInsérerInserire 0ChargerLadegerätChargeurCaricatore APilot lampKontrollampeLampe témoinSpia BLineLeitungLigneLinea CDrill bitBohrerForet de perçagePunta del trapano DPart of SDS-plus shankTeil des SDS-plus SchaftesElément de la tige SDS plusParte dell’asta SDS plus EFront capVordere AbdeckungCapuchon avantProtezione davanti FGripSpannbackeAttache coulissantePresa davanti GDust cupStaubschaleGodet a poussièreContenitore a polvere HDust collector (B)Staubfang (B)Collecteur à poussière (B)Camera a polvere (B)
NederlandsEspañolPortuguês 1Oplaadbare batterijBatería recargableBateria recarregável 2VergrendelingEngancheLingüeta 3BatterijdekselTapa de bateríaTampa da bateria 4AansluitpuntenTerminalesTerminais 5VentilatieopeningenOrificios de ventilaciónOrifícios de ventilação 6DrukkenPresionarApertar 7HandgreepAsideroCabo 8UittrekkenSacarRetirar 9InstekenInsertarInserir 0AcculaderCargadorCarregador AControlelampjeLámpara pilotoLâmpada piloto BLijnLíneaLinha CBoorstukBrocaBroca DOnderdeel van SDS Plus schachtParte del SDS más vástagoCabo de peça SDS-plus EVoorkapCubierta frontalTampa da frente FGreepSujetadorMordente GStofvangkapCopa de polvoReceptáculo para poeira HStofverzamelaar (B)Colector de polvo (B)Coletor de poeira (B)
Page 4 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 4 · Zum Vergrößern klicken
Seite 4
Hitachi DH18DSL — 〰呡扬敟䑈ㄴ䑓䱟坅 diagram (page 4)
Abb. 5
Page 5 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 5 · Zum Vergrößern klicken
Seite 5
EnglishDeutschFrançaisItaliano CDrill bitBohrerForet de perçagePunta del trapano DPart of SDS-plus shankTeil des SDS-plus SchaftesElément de la tige SDS plusParte dell’asta SDS plus EFront capVordere AbdeckungCapuchon avantProtezione davanti FGripSpannbackeAttache coulissantePresa davanti IPush buttonDruckknopfPoussoirTasto da premere JForward rotationVorwärtsdrehungRotation avantRotazione in avanti KReverse rotationRückwärtsdrehungRotation inverseRotazione indietro LPush the R sideDie R Seite drückenPousser sur le côté RSpingere il lato R MPush the L sideDie L Seite drückenPousser sur le côté LSpingere il lato L NR indicationR AnzeigeIndication RIndicazione R OL indicationL AnzeigeIndication LIndicazione L PChange leverWechselknopfBouton de changementRotella di cambio Q“ ” mark“ ” zeichenRepère “ ”Contrassetgno “ ” R“ ” mark“ ” zeichenRepère “ ”Contrassegno “ ” SDrill chuckBohrfutterMandrin porte-feretMandrino TChuck adaptorBohrutteradapterRaccord de mandrinAdattatore per mandrino UBitBohrerspitzenMèchePunta VSocketFassungPrisePresa WDepth gaugeTiefenmesserJauge de profondeurCalibro profondità XMounting holeBefestigungsöffnungOrifice de montageForo d’inserimento della bacchetta di arresto YSide handleHandgriffPoignée lateraleLaterale ZTaper shank adapterKegelschaftadapterRaccord de queue coniqueAdattatore per gambo conico [CotterDornClavetteCoppiglia \RestAuflageSupportAppoggio
NederlandsEspañolPortuguês CBoorstukBrocaBroca DOnderdeel van SDS Plus schachtParte del SDS más vástagoCabo de peça SDS-plus EVoorkapCubierta frontalTampa da frente FGreepSujetadorMordente IDruktoetsPulsadorBotão de pressão JVoorwaartse draairichtingRotación hacia la derechaRotação para frente KTerugwaartse draairichtingRotación hacia la izquierdaRotação inversa LDruk aan de R kantPresione el lado RApertar o lado R MDruk aan de L kantPresione el lado LApertar o lado L NR aanduidingIndicación RIndicação R OL aanduidingIndicación LIndicação L POmstelknopPerilla de cambioSeletor Q“ ”-markeringMarca “ ”Marca “ ” R“ ”-markeringMarca “ ”Marca “ ” SBoorkopPortabrocasMandril TBoorkopadapterAdaptador del portabrocasAdaptador do mandril UBoorstukBrocaPalhetão VAansluithusCuboEncaixe WDiepte-maatlatCalibre de profundidadSonda XMontagegatAgujero de montajeOrifício de montagem YZijgreepMango lateralEmpunhadura lateral ZVernauwde schachtadaptorAdaptador de la espigaAdaptador de cabo cônico [CotterChavetaCavilha \SteunApoyoSuporte
Page 6 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 6 · Zum Vergrößern klicken
Seite 6
Hitachi DH18DSL — 〰呡扬敟䑈ㄴ䑓䱟坅 diagram (page 6)
Abb. 6
Page 8 of the Hitachi DH18DSL user manual — 〰呡扬敟䑈ㄴ䑓䱟坅
Seite 8 · Zum Vergrößern klicken
Seite 8
Symbols WARNING The following show symbols used for the machine. Be sure that you understand their meaning before use.Symbole WARNUNG Die folgenden Symbole werden für diese Maschine verwendet. Achten Sie darauf, diese vor der Verwendung zu verstehen.Symboles AVERTISSEMENT Les symboles suivants sont utilisés pour l’outil. Bien se familiariser avec leur signification avant d’utiliser l’outil.Simboli AVVERTENZA Di seguito mostriamo i simboli usati per la macchina. Assicurarsi di comprenderne il significato prima dell’uso. Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.Lesen Sie sämtliche Sicherheitshinweise und Anweisungen durch. Wenn die Warnungen und Anweisungen nicht befolgt werden, kann es zu Stromschlag, Brand und/ oder ernsthaften Verletzungen kommen.Lire tous les avertissements de sécurité et toutes les instructions. Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des incendies et/ou des blessures graves.Leggere tutti gli avvertimenti di sicurezza e tutte le istruzioni. La mancata osservanza degli avvertimenti e delle istruzioni potrebbe essere causa di scosse elettriche, incendi e/o gravi lesioni. Only for EU countries Do not dispose of electric tools together with household waste material! In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.Nur für EU-Länder Werfen Sie Elektrowerkzeuge nicht in den Hausmüll! Gemäss Europäischer Richtlinie 2002/96/EG über Elektround ElektronikAltgeräte und Umsetzung in nationales Recht müssen verbrauchte Elektrowerkzeuge getrennt gesammelt und einer umweltgerechten Wiederververtung zugeführt werden.Pour les pays européens uniquement Ne pas jeter les appareils électriques dans les ordures ménagères! Conformément à la directive européenne 2002/96/EG relative aux déchets d’équipements électriques ou électroniques (DEEE), et à sa transposition dans la législation nationale, les appareils électriques doivent être collectés à part et être soumis à un recyclage respectueux de l’environnement.Solo per Paesi UE Non gettare le apparecchiature elettriche tra i rifiuti domestici. Secondo la Direttiva Europea 2002/96/CE sui rifiuti di apparecchiature elettriche ed elettroniche e la sua attuazione in conformità alle norme nazionali, le apparecchiature elettriche esauste devono essere raccolte separatamente, al fine di essere reimpiegate in modo eco-compatibile. Symbolen WAARSCHUWING Hieronder staan symbolen afgebeeld die van toepassing zijn op deze machine. U moet de betekenis hiervan begrijpen voor gebruik.Símbolos ADVERTENCIA A continuación se muestran los símbolos usados para la máquina. Asegúrese de comprender su significado antes del uso.Símbolos AVISO A seguir aparecem os símbolos utilizados pela máquina. Assimile bem seus significados antes do uso. Lees alle waarschuwingen en instructies aandachtig door. Nalating om de waarschuwingen en instructies op te volgen kan in een elektrische schok, brand en/of ernstig letsel resulteren.Lea todas las instrucciones y advertencias de seguridad. Si no se siguen las advertencias e instrucciones, podría producirse una descarga eléctrica, un incendio y/o daños graves.Leia todas as instruções e avisos de segurança. Se não seguir todas as instruções e os avisos, pode provocar um choque eléctrico, incêndio e/ou ferimentos graves. Alleen voor EU-landen Geef elektrisch gereedschap niet met het huisvuil mee! Volgens de Europese richtlijn 2002/96/EG inzake oude elektrische en elektronische apparaten en de toepassing daarvan binnen de nationale wetgeving, dient gebruikt elektrisch gereedschap gescheiden te worden ingezameld en te worden afgevoerd naar een recycle bedrijf dat voldoet aan de geldende milieu-eisen.Sólo para países de la Unión Europea ¡No deseche los aparatos eléctricos junto con los residuos domésticos! De conformidad con la Directiva Europea 2002/96/CE sobre residuos de aparatos eléctricos y electrónicos y su aplicación de acuerdo con la legislación nacional, las herramientas eléctricas cuya vida útil haya llegado a su fin se deberán recoger por separado y trasladar a una planta de reciclaje que cumpla con las exigencias ecológicas.Apenas para países da UE Não deite ferramentas eléctricas no lixo doméstico! De acordo com a directiva europeia 2002/96/CE sobre ferramentas eléctricas e electrónicas usadas e a transposição para as leis nacionais, as ferramentas eléctricas usadas devem ser recolhidas em separado e encaminhadas a uma instalação de reciclagem dos materiais ecológica.
Page 9 of the Hitachi DH18DSL user manual — GENERAL POWER TOOL SAFETY WARNINGS
Seite 9 · Zum Vergrößern klicken
Seite 9

GENERAL POWER TOOL SAFETY WARNINGS

c) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. d) Remove any adjusting key or wrench before

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit.

turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of

Cluttered or dark areas invite accidents. b) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. c) Keep children and bystanders away while

operating a power tool. Distractions can cause you to lose control.

dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust related hazards.

2. Electrical safety a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. b) Avoid body contact with earthed or grounded

4. Power tool use and care a) Do not force the power tool. Use the correct

power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does

surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet

not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. c) Disconnect the plug from the power source

and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children

conditions. Water entering a power tool will increase the risk of electric shock. d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an

and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools. Check for misalignment

extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits

3. Personal safety a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b) Use personal protective equipment. Always wear

etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

eye protection. Protective equipment such as dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

Page 10 of the Hitachi DH18DSL user manual — PRECAUTIONS FOR CORDLESS ROTARY HAMMER
Seite 10 · Zum Vergrößern klicken
Seite 10
5. Battery tool use and care a) Recharge only with the charger specified by the

10. When drilling in wall, floor or ceiling, check for buried electric power cord, etc. 11. Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted battery. 12. Wear ear protections Exposure to noise can cause hearing loss. 13. Do not touch the bit during or immediately after operation. The bit becomes very hot during operation and could cause serious burns. 14. Use auxiliary handles supplied with the tool. Loss of control can cause personal injury. 15. Always hold the body handle and side handle of the power tool firmly. Otherwise the counterforce produced may result in inaccurate and even dangerous operation. 16. Wear a dust mask Do not inhale the harmful dusts generated in drilling or chiseling operation. The dust can endanger the health of yourself and bystanders.

manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create a risk of injury and fire. c) When battery pack is not in use, keep it away

from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output. In the cases of 1 and 2 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function. 1. When the battery power remaining runs out, the motor stops. In such case, charge it up immediately. 2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again. Furthermore, please heed the following warning and caution. WARNING In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions. 1. Make sure that swarf and dust do not collect on the battery. During work make sure that swarf and dust do not fall on the battery. Make sure that any swarf and dust falling on the power tool during work do not collect on the battery. Do not store an unused battery in a location exposed to swarf and dust. Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.). 2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock. 3. Do not use an apparently damaged or deformed battery. 4. Do not use the battery in reverse polarity. 5. Do not connect directly to an electrical outlets or car cigarette lighter sockets. 6. Do not use the battery for a purpose other than those specified. 7. If the battery charging fails to complete even when a specified recharging time has elapsed, immediately stop further recharging.

6. Service a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

PRECAUTION Keep children and infirm persons away. When not in use, tools should be stored out of reach of children and infirm persons.

PRECAUTIONS FOR CORDLESS ROTARY HAMMER

1. Always charge the battery at a temperature of 0 – 40°C. A temperature of less than 0°C will result in over charging which is dangerous. The battery cannot be charged at a temperature higher than 40°C. The most suitable temperature for charging is that of 20 – 25°C. 2. Do not use the charger continuously. When one charging is completed, leave the charger for about 15 minutes before the next charging of battery. 3. Do not allow foreign matter to enter the hole for connecting the rechargeable battery. 4. Never disassemble the rechargeable battery and charger. 5. Never short-circuit the rechargeable battery. Short- chircuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery. 6. Do not dispose of the battery in fire. If the battery is burnt, it may explode. 7. When using this unit continuously, the unit may overheat, leading to damage in the motor and switch. Please leave it without using it for approximately minutes. 8. Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inflammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger. 9. Using an exhausted battery will damage the charger.

Page 11 of the Hitachi DH18DSL user manual — SPECIFICATIONS
Seite 11 · Zum Vergrößern klicken
Seite 11

8. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container. 9. Keep away from fire immediately when leakage or foul odor are detected. 10. Do not use in a location where strong static electricity generates. 11. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use. CAUTION 1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately. If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately. There is a possibility that this can cause skin irritation. 3. If you find rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the first time, do not use and return it to your supplier or vendor. WARNING If an electrically conductive foreign object enters the terminals of the lithium ion battery, a short-circuit may occur resulting in the risk of fire. Please observe the following matters when storing the battery. Do not place electrically conductive cuttings, nails, steel wire, copper wire or other wire in the storage case. Either install the battery in the power tool or store by securely pressing into the battery cover until the ventilation holes are concealed to prevent short-circuits (See Fig. 1).

SPECIFICATIONS

POWER TOOL

ModelDH14DSLDH18DSL No-load speed Save/Power0 – 750 min–1 / 0 – 1500 min–1 Full-load impact rate Save/Power0 – 3100 min–1 / 0 – 6200 min–1 CapacityDrillingConcrete16 mm Steel13 mm Wood18 mm Rechargeable batteryBSL1430: Li-ion 14.4 V (3.0 Ah, 8 cells)BSL1830: Li-ion 18 V (3.0 Ah, 10 cells) Weight2.1 kg2.2 kg Do not use the “SAVE“ mode when boring holes with the wood drill. There is a likelihood that the motor will burn out. CHARGER OPTIONAL ACCESSORIES (sold separately) Model UC18YRSL 1. Battery Charging voltage 14.4 V 18 V (1) BSL1430: DH14DSL Weight 0.6 kg STANDARD ACCESSORIES 1 Side handle 1 DH14DSL 2 Depth gauge 1 (2LSCK) 3 Charger 1 (2) BSL1830: DH18DSL DH18DSL 4 Plastic case 1 (2LSCK) 5 Battery 2 6 Battery cover 1 DH14DSL (NN) Without charger, plastic case, DH18DSL (NN) battery and battery cover Standard accessories are subject to change without notice.
ModelUC18YRSL Charging voltage14.4 V 18 V Weight0.6 kg
DH14DSL (2LSCK) DH18DSL (2LSCK)1 Side handle 1 2 Depth gauge 1 3 Charger 1 4 Plastic case 1 5 Battery 2 6 Battery cover 1 DH14DSL (NN) DH18DSL (NN)Without charger, plastic case, battery and battery cover

It may be convenient to prepare some extra batteries.

Page 12 of the Hitachi DH18DSL user manual — 〱䕮束䑈ㄴ䑓䱟坅
Seite 12 · Zum Vergrößern klicken
Seite 12
2. Tool and adapter
Hitachi DH18DSL — 〱䕮束䑈ㄴ䑓䱟坅 diagram (page 12)
Abb. 7

Adapter for slender shaft (SDS-plus shank) Drill bit (Slender shaft)

Page 13 of the Hitachi DH18DSL user manual — APPLICATIONS
Seite 13 · Zum Vergrößern klicken
Seite 13

Drilling holes in concrete or tile

BATTERY REMOVAL/INSTALLATION

Drill bit (slender shaft) Outer dia. Overall length Effective length 3.4 mm 90 mm 45 mm 3.5 mm

1. Battery removal Hold the handle tightly and push the battery latches (2 pcs.) to remove the battery (See Figs. 1 and 2 ). CAUTION

Never short-circuit the battery. 2. Battery installation Insert the battery while observing its polarities. (See Fig. 2)

Outer dia. Overall length Effective length 4.0 mm 110 mm 50 mm

CHARGING

5.0 mm 110 mm 50 mm 160 mm 100 mm 5.5 mm 110 mm 50 mm 6.5 mm 160 mm 100 mm 7.0 mm 160 mm 100 mm 8.0 mm 160 mm 100 mm 8.5 mm 160 mm 100 mm 9.0 mm 160 mm 100 mm

Before using the power tool, charge the battery as follows. 1. Connect the charger’s power cord to a receptacle. When the power cord is connected, the charger’s pilot lamp will blink in red. (At 1-second intervals) 2. Insert the battery into the charger. Firmly insert the battery into the charger until the line is visible, as shown in Fig. 3, 4. 3. Charging When inserting a battery in the charger, charging will commence and the pilot lamp will light continuously in red. When the battery becomes fully recharged, the pilot lamp will blink in red. (At 1-second intervals) (See Table 1) (1) Pilot lamp indication

12.0 mm 166 mm 100 mm 260 mm 200 mm 12.7 mm 166 mm 100 mm 14.0 mm 166 mm 100 mm 15.0 mm 166 mm 100 mm

The indications of the pilot lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

16.0 mm 166 mm 100 mm 260 mm 200 mm

Drilling anchor holes

Taper mode Morse taper No.1

W 1/4” W 5/16”

W 3/8”

Optional accessories are subject to change without notice.

APPLICATIONS

Rotation and hammering function Drilling anchor holes Drilling holes in concrete Drilling holes in tile Rotation only function Drilling in steel or wood

(with optional accessories) Tightening machine screws, wood screws

Show 8 more labels / short text on this page
SDS-plus Drill bit · Taper shank adapter · A-Taper · B-taper · Anchor setting · Anchor setting adapter · Anchor size · (with optional accessories)
Page 14 of the Hitachi DH18DSL user manual — PRIOR TO OPERATION
Seite 14 · Zum Vergrößern klicken
Seite 14

Indications of the pilot lamp

The pilot lamp lights or blinks in red.

Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds)

Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for 0.1 seconds. (off for 0.1 seconds)

Malfunction in the battery or the charger

The pilot lamp lights in green.

Battery overheated. Unable to charge (Charging will commence when battery cools).

(2) Regarding the temperatures of the rechargeable

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while. CAUTION When the battery charger has been continuosly

battery The temperatures for rechargeable batteries are as shown in Table 2, and batteries that have become hot should be cooled for a while before being recharged.

Table 2 Recharging ranges of batteries

used, the battery charger will be heated, thus constituting the cause of the failures. Once the charging has been completed, give 15 minutes rest until the next charging. If the battery is recharged when it is warm due to

Temperatures at Rechargeable batteries which the battery can be recharged BSL1430, BSL1830 0°C – 40°C

battery use or exposure to sunlight, the pilot lamp map light in green. The battery will not be recharged. In such a case, let the battery cool before charging. When the pilot lamp flickers in red (at 0.2-second

(3) Regarding recharging time

Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.

intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.

Table 3 Charging time (At 20°C)

UC18YRSL Battery BSL1430, BSL1830 Approx. 45 min.

PRIOR TO OPERATION

NOTE:

1. Mounting the drill bit (Fig. 5, 6) CAUTION

The charging time may vary according to temperature and power source voltage. 4. Disconnect the charger’s power cord from the receptacle. 5. Hold the charger firmly and pull out the battery. NOTE:

To prevent accidents, make sure to turn the switch off. NOTE:

When using tools such as drill bits, etc., make sure to use the genuine parts designated by our company. (1) Clean the shank portion of the drill bit. (2) Insert the drill bit in a twisting manner into the tool

After operation, pull out batteries from the charger first, and then keep the batteries properly.

holder until it latches itself. (Fig. 5) The grip need not be adjusted during bit installation. (3) Check the latching by pulling on the drill bit. (4) To remove the drill bit, fully pull the grip in the

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted. When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.

direction of the arrow and pull out the drill bit. 2. Confirm that the battery is mounted correctly. 3. Installation of dust cup or dust collector (B) (Optional accessories) (Fig. 7, Fig. 8)

Show 14 more labels / short text on this page
Table 1 · Before charging · Blinks · While charging · Lights · Lights continuously · Charging complete · Blinks · Charging impossible · Flickers · Overheat Standby · Lights · Lights continuously · Charger
Page 15 of the Hitachi DH18DSL user manual — HOW TO USE
Seite 15 · Zum Vergrößern klicken
Seite 15

When using a rotary hammer for upward drilling operations attach a dust cup or a dust collector (B) to collect dust or particles for easy operation. Installing the dust cup

These data are for the referential values. The number of holes that can be drilled varies according to the sharpness of the used bit or the conditions of the concrete being drilled. CAUTION

Use the dust cup by attaching to the drill bit as shown in Fig. 7. When using a bit which has big diameter, enlarge the center hole of the dust cup with this rotary hammer. Installing dust collector (B)

When using this unit continuously, the unit may overheat, leading to damage in the motor and switch. Please leave it without using it for approximately 15 minutes.

When using dust collector (B), insert dust collector (B) from the tip of the bit by aligning it to the groove on the grip. (Fig. 8) CAUTION The dust cup and dust collector (B) are for exclusive

HOW TO USE

1. Switch operation When the switch trigger is depressed, the tool

rotates. When the switch trigger is released, the tool stops. The rotational speed of the rotary hammer can be

use of concrete drilling work. Do not use them for wood or metal drilling work. Insert dust collector (B) completely into the chuck

controlled by varying the amount that the switch trigger is pulled. Speed is low when the switch trigger is pulled slightly and increases as the switch trigger is pulled more. When releasing the switch trigger, the brake will

part of the main unit. When turning the rotary hammer on while dust

collector (B) is detached from a concrete surface, dust collector (B) will rotate together with the drill bit. Make sure to turn on the switch after pressing dust cup on the concrete surface. When using dust collector (B) attached to a drill bit that has more than 190 mm of overall length, dust collector (B) cannot touch the concrete surface and will rotate. Therefore, please use dust collector (B) by attaching to drill bits which have 166 mm, 160 mm, and 110 mm overall length. Dump particles after every two or three holes when

be applied for immediate stopping. 2. Rotation + Hammering Turn the change lever fully in the direction of the “

” mark to set “rotation + hammering”. (1) Mount the drill bit. (2) Pull the trigger switch after applying the drill bit

at all. Pushing slightly so that drill dust comes out gradually is just sufficient. CAUTION

drilling. Please replace the drill bit after removing dust

collector (B). 4. Selecting the driver bit Screw heads or bits will be damaged unless a bit appropriate for the screw diameter is employed to drive in the screws. 5. Confirm the direction of bit rotation (Fig. 9) The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the push button. The L-side of the push button is pushed to turn the bit counterclockwise. (See Fig. 9) (The L and R marks are provided on the body.) CAUTION

When the drill bit touches construction iron bar, the bit will stop immediately and the rotary hammer will react to revolve. Therefore please grip the side handle and handle tightly as shown in Fig. 11. 3. Rotation only Turn the change lever fully in the direction of the “

” mark to set “rotation only”. (Fig. 10) To drill a wood or metal material using the optional drill chuck and chuck adapter, proceed as follows. Installing drill chuck and chuck adapter: (Fig. 12) (1) Attach the drill chuck to the chuck adaptor. (2) The part of the SDS-plus shank is the same as the

The push button cannot be switched while the power tool is turning. To switch the push button, stop the power tool, then set the push button. 6. Continuous drilling The number of holes that can be drilled in concrete after one recharge is shown in Table 4.

drill bit. Therefore, refer to the item of “Mounting the drill bit” for attaching it. CAUTION

Application of force more than necessary will

not only expedite work at all, but will deteriorate the tip edge of the drill bit and reduce the service life of the rotary hammer in addition. Drill bit may snap off while withdrawing the

Bit dia. Depth Possible continuous

(mm) (mm) drilling number (holes) DH14DSL DH18DSL *3.5 65 110 4 98 122 5 80 113 6 30 72 105 8 55 77 10 48 64 12 41 57 14 34 47 16 22 32

rotary hammer from the drilled hole. For withdrawing, it is important to use a pushing motion. Do not attempt to use the rotary hammer in the

rotation and striking mode with the drill chuck and chuck adapter attached. This would seriously shorten the service life of every component of the machine. 4. When driving wood screws (Fig. 13) (1) Selecting a suitable driver bit

Employ plus-head screws, if possible, since the driver bit easily slips off the heads of slotted-head screws.

* Use an adapter for a small diameter bit.

Table 4

Page 16 of the Hitachi DH18DSL user manual — LUBRICATION
Seite 16 · Zum Vergrößern klicken
Seite 16

(2) Tightening wood screws

Prior to tightening wood screws, make pilot holes suitable for them in the wooden board. Apply the bit to the screw head grooves and gently drive the screws in the holes. CAUTION

State of lamp Battery Remaining Power

The battery remaining power is enough.

Exercise care in preparing a pilot hole suitable for the wood screw taking the hardness of the wood into consideration. Should the hole be excessively small or shallow, requiring much power to drive the screw into it, the thread of the wood screw may sometimes be damaged. 5. Using depth gauge (Fig. 14) (1) Loosen the knob on the side handle, and insert the

The battery remaining power is a half.

The battery remaining power is nearly empty. Re-charge the battery soonest possible.

depth gauge into the mounting hole on the side handle. (2) Adjust the depth gauge position according to the

depth of the hole and tighten the knob bolt securely. 6. How to use the drill bit (taper shank) and the taper shank adapter (1) Mount the taper shank adapter to the rotary hammer.

As the remaining battery indicator shows somewhat differently depending on ambient temperature and battery characteristics, read it as a reference. NOTE: Do not give a strong shock to the switch panel or

(Fig. 15) (2) Mount the drill bit (taper shank) to the taper shank

adapter. (Fig. 15) (3) Turn the switch ON, and drill a hole to prescribed

break it.It may lead to a trouble. To save the battery power consumption, the

depth. (4) To remove the drill bit (taper shank), insert the

remaining battery indicator lamp lights while pressing the remaining battery indicator switch. 9. How to use the LED light Every time you press the light switch on the switch panel, the LED light lights or goes off. (Fig. 19) To prevent the battery power consumption, turn off the LED light frequently. CAUTION Do not expose directly your eye to the light by

cotter into the slot of the taper shank adapter and strike the head of the cotter with a hammer supporting on the rest. (Fig. 16) 7. Switching between the “SAVE“ and the “POWER“ modes The hammering force of the hammer can be increased or decreased to conform with intended usage, by operating the shift knob as per Fig. 17. Adjust the force to match the usage intended. (1) “SAVE“ mode ... decreased hammering force

looking into the light. If your eye is continuously exposed to the light, your eye will be hurt. NOTE: To prevent the battery power consumption caused

This can prevent thin drill bits which are less than 4.3 mm in diameter, from being bent or broken. (2) “POWER“ mode ... increased hammering force This can be used to speedily and efficiently drill

by forgetting to turn off the LED light, the light goes off automatically in about 15 minutes.

holes when the drill bits which are being used are greater than 4 mm in diameter. This can be used to drill holes into wood or metal. CAUTION

LUBRICATION

Do not drill holes in wood with the “SAVE“ mode. There is a likelihood that the motor will burn out because it can easily lock up due to the low power. 8. About Remaining Battery Indicator When pressing the remaining battery indicator switch, the remaining battery indicator lamp lights and the battery remaining power can be checked. (Fig. 18) When releasing your finger from the remaining battery indicator switch, the remaining battery indicator lamp goes off. The Table 5 shows the state of remaining battery indicator lamp and the battery remaining power.

Low viscosity grease is applied to this rotary hammer so that it can be used for a long period without replacing the grease. Please contact the nearest service center for grease replacement when any grease is leaking form loosened screw. Further use of the rotary hammer despite the grease shortage causes damage to reduce the service life. CAUTION A specific grease (FG-6A) is used with this machine, therefore, the normal performance of the machine may be badly affected by use of different grease. Please be sure to let one of our service centers to undertake replacement of the grease.

Table 5

Page 17 of the Hitachi DH18DSL user manual — GUARANTEE
Seite 17 · Zum Vergrößern klicken
Seite 17

MAINTENANCE AND INSPECTION

MODIFICATION

Hitachi Power Tools are constantly being improved and modified to incorporate the latest technological advancements. Accordingly, some parts may be changed without prior notice.

1. Inspecting the tool Since use of a dull tool will degrade efficiency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted. 2. Inspecting the mounting screws Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard. 3. Maintenance of the motor The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water. 4. Inspecting the carbon brushes (Fig. 20) The motor employs carbon brushes which are consumable parts. Since and excessively worn carbon brush can result in motor trouble, replace the carbon brush with new ones when it becomes worn to or near the “wear limit”. In addition, always keep carbon brushes clean and ensure that they slide freely within the brush holders. NOTE:

GUARANTEE

We guarantee Hitachi Power Tools in accordance with statutory/country specific regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a Hitachi Authorized Service Center.

When replacing the carbon brush with a new one, be sure to use the Hitachi Carbon Brush Code No. 328481. 5. Replacing carbon brushes Take out the carbon brush by first removing the brush cap and then hooking the protrusion of the carbon brush with a slotted head screw driver, etc., as shown in Fig. 22. When installing the carbon brush, choose the direction so that the nail of the carbon brush agrees with the contact portion outside the brush tube. Then push it in with a finger as illustrated in Fig. 23. Lastly, install the brush cap. CAUTION

Blue: -Neutral Brown: -Live As the colours of the wires in the mains lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal. NOTE: This requirement is provided according to BRITISH STANDARD 2769: 1984. Therefore, the letter code and colour code may not be applicable to other markers except United Kingdom.

Be absolutely sure to insert the nail of the carbon brush into the contact portion outside the brush tube. (You can insert whichever one of the two nails provided.) Caution must be exercised since any error in this operation can result in the deformed nail of the carbon brush and may cause motor trouble at an early stage. 6. Cleaning on the outside When the power tool is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, as they melt plastics. 7. Storage Store the power tool in a place in which the temperature is less than 40°C and out of reach of children. 8. Service parts list CAUTION

Information concerning airborne noise and vibration The measured values were determined according to EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 97 dB (A) Measured A-weighted sound pressure level: 86 dB (A) Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined according to EN60745.

Repair, modification and inspection of Hitachi Power Tools must be carried out by a Hitachi Authorized Service Center. This Parts List will be helpful if presented with the tool to the Hitachi Authorized Service Center when requesting repair or other maintenance. In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

Hammer drilling into concrete: Vibration emission value ah, HD = 10.8 m/s2 Uncertainty K = 2.2 m/s2

Page 18 of the Hitachi DH18DSL user manual — 〱䕮束䑈ㄴ䑓䱟坅
Seite 18 · Zum Vergrößern klicken
Seite 18

the power tool can differ from the declared value depending on the ways in which the tool is used. To identify the safety measures to protect the

operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

Frage zu Hitachi DH18DSL stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Hitachi DH18DSL

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Hitachi DH18DSL PDF-Anleitung

84 Seiten·1.3 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…