Benutzeranleitung / Produktwartung TL-R460 des Produzenten TP-Link
Zur Seite of 57
.
COPYRIGHT & TRADEMARKS S pecifications are subject to change without notice. is a registered trademark of TP-LINK T echnologies Co., Lt d. Other brands and product names are trademarks or registered trademarks of their respective holders.
Package contents .............................................................................................................. 1 Chapter 1: About this Guide .............................................................................................
5.9.1 Oray.net DDNS ........................................................................................ 36 5.9.2 Comexe.cn DDNS .................................................................................... 36 5.10 System T ools ...........
TL-R460 Cable/DSL Router User Guide Package content s The following contents should be found in your box: One TL-R460 Cable/DSL Router One AC power Adapter for TL-R460 Cable/DSL Router Qui.
TL-R460 Cable/DSL Router User Guide Chapter 1: About this Guide Thank you for choosing the TL -R460 Cable/DSL Router . This router provides dedicated solutions for Small Office/Home Of fice (S OHO) networks. With you r network all connected, your local network can share Internet access, f iles and fun for multiple PCs through one ISP account.
TL-R460 Cable/DSL Router User Guide Chapter 2: Introduction 2.1 Overview of the Router The TL-R460 Cable/DSL Router integrates a 4 - po r t s w i t ch , firewall, and NA T -router . Its design is dedicated to Small Office/Home Of fi ce (SOHO) netw ork solutions.
TL-R460 Cable/DSL Router User Guide indicate connections. V iewed from left to ri ght. T able 2-1 describes the LEDs on the front panel of the router .
TL-R460 Cable/DSL Router User Guide Chapter 3: Connecting the Router 3.1 System Requirement s Broadband Internet Access Service (DSL/Cable/Ethernet) One DSL/Cable modem that has an RJ45 co nne.
TL-R460 Cable/DSL Router User Guide Swit ch/Hub To WAN To L A N 1 W A N 234 RESET （） XDSL C able Ether net 、、 Figure 3-1 Hardware Installation of the TL-R460 Cable/DSL Router - 6 -.
TL-R460 Cable/DSL Router User Guide Chapter 4: Quick Inst allation Guide After connecting the TL-R460 router into your network, you should configure it. This chapter describes how to c onfigure the basic f unctions of your TL-R460 Cable/DSL Router . These procedure s only take you a fe w minutes.
TL-R460 Cable/DSL Router User Guide your PC and the router has been established. Figure 4-2 Failed result of Ping command If the result displayed is similar to what show n in figure 4-2, it means that your PC has not connected to the router . If so, refer to the following steps for a solution.
TL-R460 Cable/DSL Router User Guide Note : If the above screen does not prompt, it means that your web-browser has been set to a proxy . Go to T ools menu>Internet Op tions>Connections>L AN Settings, in the screen that appears, cancel the Us ing Proxy checkbox, and click OK to finish it.
TL-R460 Cable/DSL Router User Guide ISP. These fields are case s ensitive. If you have difficult y with this process, please contact your ISP. If you choose " Dyn a mi c I P ", the router will automatically receive the IP parameters from your ISP without needing to enter any parameters.
TL-R460 Cable/DSL Router User Guide Chapter 5: Configuring the Router This chapter describes eac h web page's key functions. 5.1 login After your successful login, you can confi gure and manage the router . There are nine main menus on the left of the web- based utility .
TL-R460 Cable/DSL Router User Guide Figure 5-1 Router S tatus 5.3 Quick Setup Please refer to Section 4.2: "Quick Installation Guide." 5.4 Network Figure 5-2 the Network menu There are three submenus under the Network menu (shown in figure 5-2): LAN , WA N and MAC Clone.
TL-R460 Cable/DSL Router User Guide MAC Address - The physical address of the r outer , as seen from the LAN. The value can't be changed. IP Address - Enter the IP address of your router in dotted-decimal notation (factory default: 192.168.
TL-R460 Cable/DSL Router User Guide This page displays the W AN IP paramete rs assigned dynamically by your ISP , including IP address, Su bnet Mask, Default Gateway , etc. Click the Renew button to renew the IP p arameters from your ISP . Click the Release button to release the IP parameters.
TL-R460 Cable/DSL Router User Guide Figure 5-5 WAN - S tatic IP You should type the following paramet ers into the spaces provided: IP Address - Enter the IP address in dotted-decimal notation provided by your ISP . Subnet Mask - Enter the subnet Mask in dotted-dec imal notation provided by you r ISP , usually is 255.
TL-R460 Cable/DSL Router User Guide Click Logout to end 802.1x authentication. 3. If you choose PPPoE, you should enter the following parameters (figure 5-6): Figure 5-6 WAN - PPPoE User Name/Passw ord - Enter the User Name and Password provided by your ISP .
TL-R460 Cable/DSL Router User Guide that you wish to have the Internet connec ting last unless a new link is requested. Caution : Sometimes the connection cannot be disconnected although you specify a time to Max Idle T ime. This is because t here may still be active applications in the background, which may cause f ee accounted by your ISP .
TL-R460 Cable/DSL Router User Guide 5.4.3 MAC Clone You can configure the MA C address of the WAN port on this page, figure 5-8: Figure 5-8 MAC Address Clone Some ISPs require that you register the MAC address of your adapter, which is connected to your cable, DSL modem or Ethernet duri ng installation.
TL-R460 Cable/DSL Router User Guide 5.5.1 DHCP Settings The router is set up by default as a DHCP (Dy namic Host Configuration Prot ocol) server , which provides the TCP/IP conf iguration for all the PCs that are connected to the router on the LAN.
TL-R460 Cable/DSL Router User Guide DHCP Client att ached to t he router (figure 5-1 1): Figure 5-1 1 DHCP Clients List Index - The index of the DHCP Client Client Name - The name of the DHCP client MAC Address - The MAC address of the DHCP client Assigned IP - The IP address that the router has allocated to the DHCP client.
TL-R460 Cable/DSL Router User Guide Assigned IP Address - The IP address of the router reserved. To Reserve IP addresses: 1. Enter the MAC address (The format fo r the MAC address is XX-XX-XX-XX-XX-XX.) and IP address in dotted-decimal not ation of the computer you wish to add.
TL-R460 Cable/DSL Router User Guide Figure 5-14 Virtual Servers Service Port - The numbers of External Ports. Y ou can type a service port or a range of service ports (the format is XXX – YYY , XXX is S tart port, YYY is End port).
TL-R460 Cable/DSL Router User Guide 3. Click the Save button. To delete a service entry: 1. Clear the entry's all in formation except for the Protocol pull-down list. 2. Click the Save button. To delete all service entries: 1. Click the Clear All button.
TL-R460 Cable/DSL Router User Guide T rigger Port - The port for outgoing traffic. An outgoing connection using this port will "T rigger" this rule. T rigger Protocol - The protocol used for Trigger Port s, either TCP , UDP , or All (all protocols supported by the router).
TL-R460 Cable/DSL Router User Guide Note: 1. When the trigger connection is released, the according ope ning ports will be closed. 2. Each rule allowed to be used only by one host on LAN synchronously . The trigger connection of other hosts on LAN will be refused.
TL-R460 Cable/DSL Router User Guide Enable UPnP - UPnP can be enabled or di sabl ed by clicking the Enable or Disable button. As allowing this may present a risk to securi ty, this feature is disabled by default. Current UPnP Settings Table - this table displays the current UPnP information.
TL-R460 Cable/DSL Router User Guide Figure 5-19 Firewall Settings Enable Firew all - The general firewall switch is on or off. Enable IP Address Filtering - Set IP Address Filteri ng is enabled or disabled. There are two default filtering rules of IP Address Filtering, either Allow or Reny passing through the router.
TL-R460 Cable/DSL Router User Guide To disable the IP Address Filteri ng feature, keep t he default setting, Disabled . To set up an IP Address Filt ering entry, click Enable Firewall and Enable IP Address Filtering on the Firewall page, and click the Add New… button.
TL-R460 Cable/DSL Router User Guide Click the Disable All button to disable all entries. Click the Delete All button to delete all entries You can change the entry’s order as desired.
TL-R460 Cable/DSL Router User Guide Figure 5-23 Add or Modify a Domain Filtering entry To add or modify a Domain Filteri ng entry, follow these instructions: 1. Effective Time - Enter a range of time in HHMM format, which point to the range time for the entry to take effect.
TL-R460 Cable/DSL Router User Guide 5.7.4 MAC Filtering Like the IP Address Filtering page, the MAC Address Filtering page (shown in figure 5-24) allows you to control access to the Internet by users on your local network based on their MAC addresses.
TL-R460 Cable/DSL Router User Guide Click the Enable All button to enable all entries. Click the Disable All button to disable all entries. Click the Delete All button to delete all entries. Click the Next button to go to the next page and click the Previous button to return to the previous page.
TL-R460 Cable/DSL Router User Guide router's password. After succe ssfully entering the password, you will be able to access the router's w eb-based utility. Note: Be sure to change the router's default password to a very secure password .
TL-R460 Cable/DSL Router User Guide value between 5 ~ 3600 packets. When the current UPD-FLOOD Packets numbers are beyond the set value, the router will st art up the blocking function immediately . Enable TCP-SYN-FLOOD Att ack Filtering - Enable or Disable the TCP-SYN- FLOOD Attack Filtering.
TL-R460 Cable/DSL Router User Guide Figure 5-29 S tatic Routing T o add st atic routing entries: 1. Enter the following data: Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.
TL-R460 Cable/DSL Router User Guide 5.9.1 Oray.net DDNS If your selected dynamic DNS Service Provider is www.oray.net . The page shown in figure 5-30 will appear: Figure 5-30 Oray .net DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the User Name for your DDNS account.
TL-R460 Cable/DSL Router User Guide Figure 5-31 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. T ype the domain names your dynamic DNS service provider gave. 2. T ype the User Name for your DDNS account. 3. T ype the Passw ord for your DDNS account.
TL-R460 Cable/DSL Router User Guide 5.10.1 Time Y ou can set the time manually or get GMT from the Internet for the router on this page (shown in figure 5-33): Figure 5-33 T ime settings Time Zone - Select your local time zone from this pull down list.
TL-R460 Cable/DSL Router User Guide New firmware versi ons are posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use.
TL-R460 Cable/DSL Router User Guide Figure 5-36 Reboot the router Click the Reboot button to reboot the router. Some settings of the router will take effect only after rebooting, which include: • Change LAN IP Address. (Syste m will reboot automatically) • MAC Clone (system will reboot automatically) • DHCP service function.
TL-R460 Cable/DSL Router User Guide 5.10.6 Log This page (shown in figure 5-38) allows you to query the Logs of the router. Figure 5-38 System Log The router can keep logs of all traffic. Y ou can query the logs to find what happened to the router. Click the Refresh button to refresh the logs.
TL-R460 Cable/DSL Router User Guide Statistics Table: IP A ddress The IP address displayed with statistics Packets The total amount of packets rece ived and transmitted by the router. Total Bytes The total amount of bytes receiv ed and transmitted by the router.
TL-R460 Cable/DSL Router User Guide Appendix A: F AQ 1. How do I configure the router to access Internet by ADSL users? 1) First, configure the ADSL modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL modem to the W AN port on t he router .
TL-R460 Cable/DSL Router User Guide your browser , and then click "MAC Clone" submenu link. On the "MAC Clone" page, if your PC’ s MAC address is a proper MAC address, click the "Clone MAC Address" button and your PC’s MAC address will fill in the "W AN MAC Address" field.
TL-R460 Cable/DSL Router User Guide Figure A-5 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the router , you must change the WEB management port number to avoid interference.
TL-R460 Cable/DSL Router User Guide Appendix B: Configuring the PCs In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows 95/98. First make sure your Ethernet Adapter is working, refer to the adapter ’s manual if needed.
TL-R460 Cable/DSL Router User Guide window that appears. An example is shown in the following figure: Figure B-3 Configuration tab 3) Click on Properties . The following TCP/IP Properties window will display and the IP Address tab is open on this window by default.
TL-R460 Cable/DSL Router User Guide Figure B-5 Gateway tab c. Choose Disable DNS on the DNS c onfiguration tab, as shown in the following figure: Figure B-6 DNS Configuration tab • Setting IP address manually a. Select S pecify an IP address on IP Ad dress tab, as shown in the following figure.
TL-R460 Cable/DSL Router User Guide Figure B-7 IP Address t ab b. T ype the router ’s LAN IP address (t he default IP is 192.168.1.1) into the N ew g at e way field on the Gateway tab, and click on the Add button, as shown in the figure: Figure B-8 Gateway tab c.
TL-R460 Cable/DSL Router User Guide click Add button . Shown below: Figure B-9 DNS Configuration tab Now , all the configurations are finished, it will take ef fect after reboot.
TL-R460 Cable/DSL Router User Guide Appendix C: S pecifications General S tandards IEEE 802.3, 802.3u Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Ports One 10/100M Auto-Negotiation WAN RJ45 port.
TL-R460 Cable/DSL Router User Guide Appendix D: Glossary DDNS ( D ynamic D omain N ame S ystem) - The capability of assigning a fixed host and domain name to a dynamic Internet IP address.
TL-R460 Cable/DSL Router User Guide Appendix E: Cont act Information For help with the installation or operation of the TP-LINK TL-R460 Cable/DSL Router, please contact us.
Ein wichtiger Punkt beim Kauf des Geräts TP-Link TL-R460 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie TP-Link TL-R460 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für TP-Link TL-R460 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von TP-Link TL-R460 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über TP-Link TL-R460 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon TP-Link TL-R460 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von TP-Link TL-R460 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit TP-Link TL-R460. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei TP-Link TL-R460 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
