Benutzeranleitung / Produktwartung RY52905 des Produzenten Ryobi
Zur Seite of 24
OPERA TOR’S MANUAL TP30 GAS PRUNER R Y52504/R Y52905 SA VE THIS MANUAL FOR FUTURE REFERENCE Y our pruner has been engineered and manufactured to our high standard for dependability , ease of operation, and operator safety . When pr operly cared for , it will give you years of rugged, trouble-free performance.
2 Introduction ..................................................................................................................................................................... 2 General Safety Rules ...................................
3 WARNING! Read and understand all instructions. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . READ ALL INSTRUCTIONS For safe operation, read and understand all instructions before using this product.
4 Kickback is a dange rous reactio n that can lead to serious injury. Kickback may occur when the moving chain con- tacts an object at the upper portion of the tip of the guide bar or when the wood closes in and pinches the chain in the cut.
5 SYMBOLS Some of the following symbols may be used on this product. Please study them and lear n their meaning. Pr oper inter - pretation of these symbols will allow you to operate the pr oduct better and safer . SYMBOL NAME DESIGNA TION/EXPLANA TION Safety Alert Precautions that involve your safety .
6 SYMBOLS SERVICE Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for r epair . When servic- ing, use only identical replacement parts.
7 FEA TURES Fig. 1 PRODUCT SPECIFICA TIONS Engine Displacement....................................................................................................................................................... 30cc Bar length .....................
8 A TT ACHING THE “J” HANDLE See Figure 2. Hold the top and bottom clamp snugly in position on the shaft housing so that the handle will be located to the operator’s left. Insert the end of the handle between the clamps. Align the bolt holes and push the long bolt (1/4-20 x 1-1/2 in.
9 Reinstall the bolt, lock washer, and hex nut to secure. Connect the latch on the shoulder harness to the strap hanger. ASSEMBL Y CONNECTING THE POWER HEAD TO THE EXTENSION SHAFT AND PRUNER A TT ACH- MENT See Figure 4. The pruner attachment connects to the power head, or for extra reach to an extension shaft, by means of a coupler device.
10 ASSEMBL Y FILLING T ANK Clean surface around fuel cap to prevent contamina- tion. Loosen fuel cap slowly. Rest the cap on a clean surface. Carefully pour fuel into the tank. Avoid spillage. Prior to replacing the fuel cap, clean and inspect the gasket.
11 WARNING: Do not allow familiarity with this product to make you ca re le ss. Re mem be r t hat a car eles s frac ti on of a se con d is sufficient to inflict serious injury . WARNING: Always wear safety goggles or safety glasses with side shields, a hard hat, and safety shoes when op- er a ti n g po we r t o ol s .
12 OPERA TION Fig. 7 CUTTING GUIDE Fig. 6 NOTE: For second and final cuts (fro m top of limb or branch), hold fr ont cutting guide against the limb being cut. This will help steady the limb and make it easier to cut. Allow chain to cut for you; exert only light downward pressur e.
13 OPERA TION Fig. 12 POSITION FOR ST ARTING See Figure 9. Lay the pruner on the gr ound and ensure that no objects or obstructions ar e in the immediate vicinity . Make sure nothing can come in contact with the bar and chain. Fig. 10 Fig. 9 ST ARTING AND STOPPING See Figures 10 - 12.
14 fLA TS APPROX .050 in. Fig. 14 Fig. 13 WARNING: When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust.
15 MAINTENANCE REPLACING THE BAR AND CHAIN See Figures 15 - 20. WARNING: T o avoid possible serious injury , stop engine before re- placing the bar , chain, or performing any maintenance operation. Remove the bar nut and drivecase cover. The bar cont ains a bar stud slot that fit s over the bar stud.
16 IDLE SPEED ADJUSTMENT See Figure 21. If the chain turns at idle, the idle speed screw needs adjusting on the engine. T urn the idle speed scr ew counterclockwise to reduce the idle RPM and stop the chain movement. If the saw chain still moves at idle speed, contact a service dealer for adjustment and discontinue use until the repair is made.
17 MAINTENANCE CUTTING CORNER SIDE PLA TE DEPTH GAUGE TOE GULLET HEEL RIVET HOLE TOP PLA TE P ARTS Of A CUTTER Fig. 24 HOW TO SHARPEN THE CUTTERS See Figures 24 - 27. Be careful to file all cutters to the specified angles and to the same length, as fast cutting can be obtained only when all cutters are uniform.
18 MAINTENANCE CLEANING AIR FIL TER SCREEN See Figure 28-29. For proper performance and long life, keep air filter clean. Remove the air filter cover by pushing down on the latch with your thumb while gently pulling on the cover . Brush the air filter screen lightly to clean.
19 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE REMEDY Engine will not start. No spark. No fuel. Engine is flooded. Starter rope pulls harder now than when new . Cle an or rep lace s par k plug. Res et spa rk plu g gap. Refer to S pa rk Pl ug Re p la ce m en t ea rli er in t his ma nual.
20 W ARRANTY LIMITED WARRANTY ST A TEMENT T echtronic Industries North America, Inc., warrants to the original retail purchaser that this R YOBI ® brand outdoor product is free from defect in material and workmanship and agrees to repair or replace, at T echtronic Industries North America, Inc.
21 W ARRANTY THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) ST A TEMENT ONL Y APPLIES TO MODEL NUM- BERS REQUIRED TO MEET THE CARB REQUIREMENTS. The U.S. Environmental Protection Agency (EP A), the California Air Resources Board (CARB), and T echtronic Industries North America, Inc.
22 EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED P ARTS LIST Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours or Y early or Y early CA T AL YST MUFFLER ASSEMBL Y ............
23 NOTES.
987000-194 10-18-07 (REV :01) OPERA TOR’S MANUAL TP30 GAS PRUNER R Y52504/R Y52905 W ARNING: The engine exhaust fr om this product contains chemicals known to the State of Califor nia to cause cancer , birth defects, or other repr oductive harm. CALIFORNIA PROPOSITION 65 TECHTRONIC INDUSTRIES NOR TH AMERICA, INC.
Ein wichtiger Punkt beim Kauf des Geräts Ryobi RY52905 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ryobi RY52905 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ryobi RY52905 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ryobi RY52905 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ryobi RY52905 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ryobi RY52905 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ryobi RY52905 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ryobi RY52905. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ryobi RY52905 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
