Benutzeranleitung / Produktwartung SDS des Produzenten Perle Systems
Zur Seite of 162
IOLAN SDS/SCS/STS/MDC Command Line Interface Reference Guide Version 3.7 Part #5500210-14 December 2008.
Copyright S tatement This document must not be repro duced in any way whatsoever , either printed or electronicall y , without the consent of: Perle Systems Limi ted, 60 Renfrew Drive Markham, ON Canada L3R 0E1 Perle reserves the right to make change s without further notice, to any products to improve reliability , function, or design.
IOLAN SDS/SCS/STS/MDC CLI Re ference Guide, V ersion 3.7 3 Preface ........................ ....................................................... 13 About This Book .............. .................................... ...................... 13 Intended Audience .
4 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Show Console ............ ................................. ................................. ........... 26 Show Custom-App ............... ....................................................
5 Show TruePort ........... .................................................................. ........... 38 Email Commands ................... .............................. ...................... 39 Set Email-Alert Server . ................. ......
6 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Kill Line ............ ............................................................................. ........... 51 Kill Session............. .......................................... ........
7 Set Termtype ......... .......................................... .............. ............... ........... 76 Show Line............ ............................................ .............. ............... ........... 77 Line Service Commands . .
8 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Delete Modem........... ................................................. ................ .............. 97 Set Modem ................ .........................................................
9 Show Server ............. ................................................................. ............ 108 Show WINS............... ................................................. ................ ............ 108 Gateway Commands ..............
10 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete VPN Exception.......... ........................................................ ......... 122 Show VPN Exception .... ............................................................ ....
11 Netload .............. ............................................ ............................ ............ 130 Netsave ................ ........................................................ .............. ............ 131 Custom Factory Default .
12 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Line ................ ...................................................................... 142 Set Line Service ....... .................................................................
IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 13 Preface About This Book This guide provides the information you need to : z configure the IOLAN using the Command Line Interface (CLI) Intended Audience This guide is for adm inistrators who will be configuring th e IOLAN.
Contacting T ech nical Support 14 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Cont acting T echnical Support Making a T echnical Support Query Who T o Cont act If you bought your produ ct from a registered Perle supplier, you must contact their T echnical Supp ort department; they are qualified to deal with you r problem.
15 Contacting T echnical Support Rep air Procedure Before sending a IOLAN for repair, you must contact your Perle supplier . If, however , you boug ht your product directly from Perle you can contact direct ly . Customers who are in Europe, Afri ca or Middle East can submit repair d etails via a websit e form.
Contacting T ech nical Support 16 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7.
IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 17 Introduction Chapter 1 1 This book provides the command line interface (CLI) options availabl e for the IOLAN. The commands are grouped by function. CLI Conventions This section explains how to interpret the CLI s yntax.
CLI Conventions 18 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Command Shortcut s When you type a command, you can specify the shortest unique ve rsion of that command or you can press the ESC or TA B key to complete the command.
IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 19 Server Commands Chapter 2 2 This chapter defines all the CLI commands a ssociated with configuring the IOLAN server parameters. Server Commands Set Console Set Custom-App Description Sets the flow control and baud rate on IOLAN models that have a dedicated console port.
Server Commands 20 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Port-Buffering Description Configures port buffering. User Level Admin Syntax set port-buffering [duplicate -nfs-to-sysl.
Server Commands 21 Server Commands Set Server Description Sets server parameters. User Level Admin Syntax set server [auto-obtain-dns o n|off] [auto-obtain-gw on|off] [auto-obtain-wins on|off] [banner.
Server Commands 22 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 dhcp-update-dns The DHCP server will update the DNS server when the IOLAN requests a DHCP IP address (the communicati on between the DNS server and the DHCP server must already be set up in your network).
Server Commands 23 Server Commands password-limit The number of attempts a user is allowe d to enter a password for a serial port connection from the network, before the conn ection is terminated and the user has to attempt to login again.
Server Commands 24 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Server session-escape-string A configurable string that allows access to a port to view the multisession screen options, allowing the various options while accessing the pa rticular port on the IOLAN.
Server Commands 25 Server Commands Set Service validation-criteria Any values that are entered in the validation criteria m ust match the peer certificate for an SSL connection; any fiel ds left blank wi ll not be validated against the peer certificate.
Server Commands 26 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Console Show Custom-App Show Server Show Port-Buffering httpd HTTP daemon process in the IOLAN on port 80. snmpd SNMP daemon process in the IOLAN on port 16 1. spcd SPC (T ruePort) daemon process in the IOLAN that supports T ruePo rt Full Mode on UDP port 668.
Server Commands 27 Hardware Commands Show Modbus Hardware Commands Set Ethernet Show Hardware SSH Server Commands Set SSH-Server See Keys and Certificates in the IOLAN User’ s Guide for information abou t th e keys and certificates that need to be uploaded or downloaded with the IOLANs SSH server .
SSH Server Commands 28 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show SSH-Server authentication dsa An authentication method used by SSH version 2. Use DSA authen tication for the SSH session. authentication passw ord The user types in a pa ssword for authentication.
Server Commands 29 SSL/TLS Commands SSL/TLS Commands Set SSL Server Description Sets the default SSL/TLS parameters for the server . User Level Admin Syntax set ssl server [version any|t slv1|sslv3] [.
SSL/TLS Commands 30 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Server Cipher-suite organisation-unit Up to a 64 character entry fo r the u nit in the organisation; for example, Payroll. This field is case sensitive in order to successfully match the inform ation in the peer SSL/TLS certificate.
Server Commands 31 Modbus Commands Show SSL Modbus Commands Set Modbus Gateway key-exchange The type of key to exchange for the encryption format: z Any —Any key exchange that is valid is used (this does not, however , include ADH keys). z RSA —This is an RSA key exchange using an RSA key and certificate.
Modbus Commands 32 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Modbus req-next -delay A delay , in milliseconds, to allow serial sl ave(s) to re-enable receivers before issuing next Modbus Master request.
Server Commands 33 Authentication Commands Authentication Commands Set Authentication Set Authentication Local Description Sets the authentication method for the IOLAN.
Authentication Commands 34 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Authentication Kerberos Set Authentication LDAP Description Configures Kerberos authentication settings.
Server Commands 35 Authentication Commands Set Authentication NIS Add RADIUS Delete RADIUS Description Sets NIS authentication parameters. User Level Admin Syntax set authentication nis [domai n < string >] [primary < config_host >] [secondary < config_host >] Options domain The NIS domain name.
Authentication Commands 36 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Authentication RADIUS Description Sets RADIUS parameters. User Level Admin Syntax set authentication radius [ac .
Server Commands 37 Authentication Commands Set Authentication T ACACS+ Set Authentication SecurID Description Configures T A CACS+ au thentication settings.
T ruePort Ba ud Commands 38 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Authentication T ruePort Baud Commands Set T ruePort Remap-Baud Show T ruePort Description Shows the authentication settings. If you ty pe just the show authentication command, the configured primary and sec ondary authenti cation methods are displayed.
Server Commands 39 Email Commands Email Commands Set Email-Alert Server Show Email-Alert Server Description Configures email alert se ttings for the server .
Clustering Commands 40 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Clustering Commands Add Clustering Slave-IP Delete Clustering Slave-IP Description Adds a slave IOLAN to the clus tering group.
Server Commands 41 Clustering Commands Set Clustering Slave-IP Show Clustering Slave-IP Description Modify the parameter associated with a specific port in a clustering group.
Dynamic DNS Commands 42 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Dynamic DNS Commands Set Dynamic-DNS Set Dynamic-DNS SSL Description Configures the dynamic DNS parameters.
Server Commands 43 Dynamic DNS Commands country A two character count ry code; for example, US. This fi eld is case sensitive in order to successfully match the information in the peer SS L/TLS certificate. state-province Up to a 128 character entry for the s tate/pr ovince; for example, IL.
Dynamic DNS Commands 44 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Dynamic-DNS SSL Cipher-Suite Description Sets the SSL/TLS cipher suite parameters for the connection between the IOLAN and the DNS server .
Server Commands 45 PCI Commands Show Dynamic-DNS PCI Commands Set PCI Card Show PCI hmac Select the key-hashing for message authenticat ion method for your encryption type: z Any z MD5 z SHA1 The default is Any . Description Shows the dynamic DNS setting s.
PCI Commands 46 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set PCI Wireless-W AN Show Wireless-W AN Description Configures the wireless W AN parameters.
Server Commands 47 IPv6 Commands IPv6 Commands Set IPv6 Show IPv6 Description Configures the basic IPv6 settings. User Level Admin Syntax set ipv6 [dhcpv6-settings ipv 6-address on|off] [dhcp-settings.
IPv6 Commands 48 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Add Custom-IPv6 Description User Level Admin Syntax add custom-ipv6 [eth1|eth2] m ethod auto network-prefix < network_prefi.
Server Commands 49 IPv6 Commands Set Custom-IPv6 Delete Custom-IPv6 Description Configures custom IPv6 network and IP addresses. User Level Admin Syntax set custom-ipv6 [eth1|eth2] < config_ip v6_a.
IPv6 Router Advertise ments 50 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 IPv6 Router Advertisement s Set IPv6-Router -Advertisement Show IPv6-Router-Advertisement Description Configures IPv6 rout er advertisements.
IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 51 User Commands Chapter 3 3 This chapter defines all the CLI commands avai lable to users who are logged into the IOLAN. Commands for Users Logged Into the IOLAN Admin Help Kill Line Kill Session Logout Description Changes a Normal-level user to the Admin user .
Commands for Users Logged Into the IOLAN 52 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Menu Ping Resume Rlogin Screen Description Switches from a command line based interface to Menu mode of operation.
User Commands 53 Commands for Users Logged Into the IOLAN Set T ermtype Set User Description Sets the type of terminal bei ng used for the current session.
Commands for Users Logged Into the IOLAN 54 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User Session rou ti n g Determines the ro uting mode used for RIP p a ckets on the PPP and SLIP interfaces for this user . V alues are: z None —RIP packets are neither received nor sent by the IOLAN.
User Commands 55 Commands for Users Logged Into the IOLAN Show Line Users SSH Description Shows the users who are on the line. User Level Admin Syntax show line users Description St arts an SSH session to th e specified host/IP address.
Commands for Users Logged Into the IOLAN 56 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Syslog Console Show Sessions Show T ermtype Star t ssh-2-cipher -list Select the order of negotiati.
User Commands 57 Commands for Users Logged Into the IOLAN Te l n e t Description Starts a telnet session to the specified host/IP address. User Level Normal, Admin Syntax telnet < hostname/IP_addre.
Configuring Users 58 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Ve r s i o n Configuring Users Add User Delete User escape Defines the escape character . Returns you to the command line mode. This value is in hexadecimal with a default value of 1d (ASCII value GS ).
User Commands 59 Configu ring Users Set Default User Description Configures the Default User . When adding a new user , the profile of the default user will be used to assign th e values of the va rious parameters of the new user .
Configuring Users 60 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 framed-mtu Used for User Service PPP or SLIP , specifies the maximum size of packets, in bytes, being transferred across the link.
User Commands 61 Configu ring Users level The access that a user is allowed: z Admin —The admin level user has total access to the IOLAN. Y ou can create more than one admin user account but we recomm end t hat you only ha ve one. They can monitor and configure t he IOLAN.
Configuring Users 62 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User sess-timer The amount of time, in seconds, that the Session Timer will run. Use t his timer to forcibly close a user ’ s sess ion (connection). When the Session Timer expires, the IOLAN will end the connection.
User Commands 63 Configu ring Users framed-compression Used for User Service PPP or SLIP , determines whether V an Jacobsen Compression is used on the link. VJ compression is a mean s of reducing the standard TCP/IP header from 40 octets to approximately 5 octets.
Configuring Users 64 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 hotkey-pre fix The prefix that a user types to control the current session. The default value is hex 01 , which corresponds to Ctrl-a ( ^a ) (hex value 02 would be Ctrl-b (^b), etc.
User Commands 65 Configu ring Users netmask This is used for the PPP or SLIP Service type s. Only used for IPv4. If the remote user is on a sub net , e nter the network’ s subnet mask. For example, a subnet mask of 255.255.0.0. password The password the user will need to enter to login to the IOLAN.
Configuring Users 66 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set User Session Show Default User Show User Description Configures a users session settings . See Set User Session on page 54 for a description of the options. User Level Admin Syntax set user .
IOLAN SDS/SCS/STS/MD C CLI Reference Guide, V ersion 3.7 67 Line Commands Chapter 4 4 This chapter defines all the CLI commands associat ed with configuring the IOLAN ’ s l ine parameters.
Line Commands 68 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 connection-method Determines how a modem will wo rk on the line. Select from the following options: z Direct Connect —Indicates that the re is not a modem on the l ine. This is the default.
Line Commands 69 Line Commands break Specifies how a break is interpreted: z off —The IOLAN ignores the break key completely and it is not passed through to the host. This is the default setting. z local —The IOLAN deals with the break locally . If the user is in a session, the break key has the same effect as a hot key .
Line Commands 70 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 keepalive Enables a per -connection TCP keepalive f eature. After the configured number of seconds, the connection will send a gratuit ous ACK to the network peer , thus either ensuring the connection stays active OR cau sing a dro pped connection condition to be recognized.
Line Commands 71 Line Commands stop-bits Specifies the number of stop bits that follow a byte. The 1.5 opt ion is only available on the 1-port and 2-port models, but not on the m odem of the SDS1M or SDS3M models.
Line Commands 72 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Line Interface The SCS, STS, and MDC IOLAN mo dels support the EIA-232 interf ace only . Therefor e, you do not need to specify interface eia-232 in the command syntax; you only need to specify the command options (e.
Line Commands 73 Line Commands Set Line Service tx-driver-contr ol Used with a EIA-485 serial interface, if y our applica t ion supports RTS (Request T o Send), select this optio n.
Line Commands 74 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Syntax set line .|< number >|* service bidir < config_host > < server_port > < host_port > set line .|< number >|* service direct| silent rlogin < config_host > set line .
Line Commands 75 Line Commands rlogin Sets the line for a remote login connection. raw Creates a connection where no authentication takes place and data is passed unchanged. telnet Sets the line for a telnet connection. ssh Sets the line for an SSH connection.
Line Commands 76 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Modem Set T ermtype client-initiated When this option is turned on, the IOLAN will wait for a connection from th e T ruePo rt host (see the TruePort documentation for in formation on how to set up this feature on the T ruePort host).
Line Commands 77 Line Commands Show Line Option wyse60|vt100|ansi|dumb|tvi925|ibm31 51te|vt320|hp700|t erm1|term2|term3 Specifies the type of term inal connected to the line: z Dumb z WYSE60 z VT100 z.
Line Service Commands 78 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Line Service Commands Set Custom-App Set Rlogin-Client Set T elnet-Client Description Y ou can create a custom application that can run on a specific se rial line in IOLAN using the Perle SDK.
Line Commands 79 Line Service Commands Set SSH-Client echo Defines the echo character . When Line Mode is On , typing the echo character echoes the text locally and sends only completed lines to the ho st. This value is in hexadecimal with a default value of 5 (ASCII value ^E ).
Line Service Commands 80 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 auto-login Creates an automatic SSH login, using the Name and Password values. name The user ’ s name when Auto Login is enabled. password The user ’ s password when Auto Login is enabled.
Line Commands 81 Line Service Commands Set PPP Description Configures the Lines PPP settings. User Level Admin Syntax set ppp wireless-wan|line .|< number >|* [accm < 8_hex_digits >] [addr.
Line Service Commands 82 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 ipaddr -neg Specifies whether or not IP address negotiatio n will take place. IP address negotiation is where the IOLAN allow s the remote end to sp ecify its IP address.
Line Commands 83 Line Service Commands netmask The ne two rk s ub net mas k. F or ex amp le, 25 5.2 55. 0.0 . If your user is authenticated by RADIUS and the RADIUS parameter Fr amed-Netmask is set in the RADIUS file, the IOLAN will use the value in the RADIUS f ile in preference to the value configured here.
Line Service Commands 84 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 ruser This field is used to authenticate a user connect ing to this line. It is used in conjunction with the rpassword field. By specifying a name here , this line becomes dedicated to that user only .
Line Commands 85 Line Service Commands Set PPP Dynamic-DNS Set SLIP Description This option is only available when IP address negotiation ( ipaddr-neg ) is on . When enabled, the IOLAN will automatically updat e the DNS server with the specified host name and negotiated IP address for the PPP sessi on.
Line Service Commands 86 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set UDP ripaddr The IPv4 address of the remote end of the SLIP link. Choose an address that is part of the same network or subnetwork as the IOLAN.
Line Commands 87 Line Service Commands Set Vmodem both|in|out|none The direction in which inform ation is received or relayed: z None —UDP service not enabled. z In —LAN to serial. The IOLAN will listen on p ort value configured i n the DS Port parameter for messages coming from the learned or configured port.
Line Service Commands 88 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 failure-string String that is sent to the serial device when a connection fails. If no string i s entered, then the string NO CARRIER will be sent. host The target host name.
Line Commands 89 Line Service Commands style One of the following: z V erbose —Return codes (strings) are se nt to the connected device. z Numeric —The following characters can be sent to the conn.
Line Service Commands 90 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Vmodem-Phone Set SSL Line Description This command associates a phone number wi th an IP address and TCP port. This enables the existing modem application to issue a dial command with a phone number .
Line Commands 91 Line Service Commands type Specify whether the IOLAN will act as an SSL/TLS client or server . The default is Client . verify-peer Enable this option when you want the V alidat ion Criteria to match the Peer Certificate for authentication to pass.
Line Service Commands 92 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set SSL Line Cipher-suite Description Sets the SSL/TLS cipher s u ite parameters for the line.
Line Commands 93 Line Service Commands Set Modbus-Slave Line Set Modbus-Master Line Description Sets the Modbus slave pa rameters for the line. User Level Admin Syntax set modbus-slave line .
Line Service Commands 94 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Power-Management Line slave-ip The IP address of the TCP/Ethernet Modbus Slave. uid-range When Range Mo de is Hos t and you have sequential Modbus Slave IP addresses (for example, 10.
Line Commands 95 Line Service Commands Set Multihost Line Set Line Initiate-Connection Show Custom-App Show Interface Show Power-Management Description Configures multiple host s or a primary/back up .
Line Service Commands 96 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show PPP Show Rlogin-Client Show SLIP Show SSH-Client Show T elnet-Client Show Modbus Show UDP Show Vmodem Show Vmodem-Phone Description Shows the PPP line settings.
Line Commands 97 Modem Commands Modem Commands Add Modem Delete Modem Set Modem Show Modems Description Adds a modem. User Level Admin Syntax add modem < modem_name > < initi alization_string > Options < mo dem_name > The name of the modem.
Email Commands 98 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Email Commands Set Email-Alert Line Description This command configur es email alert parameters for the line.
Line Commands 99 Packet Forwarding Commands Show Email-Alert Line Packet Forwarding Commands Set Packet-Forwarding Line Description Shows how the line email alert is configured.
Packet Forwarding Commands 100 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 delay-between-messages The minimum time, in milliseconds, between mess ages that must pass before the data is forwarded by the IOLAN. The range is 0-65535. Th e default is 250 ms.
Line Commands 101 Packet Forwarding Commands eof2 When enabled, creates a sequen ce of characters that must be received to define the end of the frame (if the EOF1 char acter is not immediately foll o.
Packet Forwarding Commands 102 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Packet-Forwarding Line Description Shows the packet-forward ing settings for the line.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 103 Network Commands Chapter 5 5 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s network parameters. SNMP Commands Add Community Add T rap Description Adds an SNMP community (version 1 and version 2).
SNMP Commands 104 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete Community Delete T rap Set SNMP Description Deletes an SNMP community (version 1 and version 2).
Network Commands 105 SNMP Commands Set SNMP V3-Security Description Configures SNMP settings for the V ers ion 3 read-write and read-only user . User Level Admin Syntax set snmp v3-security readonly [.
TFTP Commands 106 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show SNMP TFTP Commands Set Server TFTP Host s Commands Add Host Delete Host Description Shows SNMP settings, including communities and traps. User Level Admin Syntax show snmp Description Configures the IOLANs TFTP client settings.
Network Commands 107 DNS/WINS Commands Set Host Show Host s DNS/WINS Commands Add DNS Add WINS Description Configures a host in the IOLAN host table. User Level Admin Syntax set host < config_host > < IP_ad dress > set host < config_host > fqdn < text > Options < config_host > The name of the host.
DNS/WINS Commands 108 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete DNS Delete WINS Show DNS Show Server Show WINS Description Deletes a DNS entry .
Network Commands 109 Gateway Commands Gateway Commands Add Gateway Description Adds a gateway . Y ou can configure up to twenty gateways. User Level Admin Syntax add gateway < config_host > def .
Gateway Commands 1 10 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Delete Gateway Set Gateway Show Gateways Description Deletes a gateway . User Level Admin Syntax delete gateway < config_gatewa y_host > Option < config_gateway_host > Y ou can view the configured gateways that can be deleted by typing delete gateway ? .
Network Commands 1 1 1 Logging Commands Logging Commands Set Syslog Show Syslog Description Configures the system log. User Level Admin Syntax set syslog [level emergency|alert|critical|er ror|warning.
RIP Commands 1 12 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 RIP Commands Add RIP Delete RIP Description Adds a RIP MD5 key . After pressing Enter , you will be prompted for the MD5 key value.
Network Commands 1 13 RIP Commands Set RIP Show RIP Description Configures the RIP MD5 key . After p ressing Enter , you will be prompted for the MD5 key value.
IPsec Commands 1 14 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Show RIP Peers IPsec Commands Once there is an active VPN tunnel , the IOLAN expects all connections to be established through a VPN tunnel.
Network Commands 1 15 IPsec Commands Options authentication-method Specify the authentication metho d that will be used between VPN peers to authenticate the VPN tunnel. Data Options: z Shared Secr et —A text-based secret that is used to authenticate the IPsec tunnel (case sensitive).
IPsec Commands 1 16 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 remote-external-ip-address When NA T T raver sal (NA T_T) is enabled, the remote VPN’ s public external IPv4 or IPv6 address or FQDN. If you want to accept a VPN connect ion from any host/network, you can enter %any in this field.
Network Commands 1 17 IPv6 T unnels Show IPsec IPsec IPv6 T unnels Add IPv6tunnel email Up to a 64 character entry for an email address; for example, acct@anycompany .com. This field is case sensitive in order to succe ssfully match th e information in the remote X.
IPv6 T unnels 1 18 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Set IPv6tunnel Show IPv6tunnel Delete IPv6tunnel Description Configures the speci fied IP v6 tunnel.
Network Commands 1 19 L2TP/IPsec L2TP/IPsec Once L2TP/IPsec is enabled, the IOLAN expects all conn ections to be estab lished through a VPN tunnel. T o allows hosts to connect outsid e of the VPN tunnel, you must configure VPN exceptions, see VPN Exceptions on page 121 for the command syntax.
L2TP/IPsec 120 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 country A two character country code; fo r example, US. This field is case sensitive in order to successfully match the information in the re mote X.509 certificate. An asterisk (*) works as a wildcard.
Network Commands 121 VPN Exceptions Show L T2P VPN Exceptions VPN exceptions allows specific hosts or any host in a network to conn ect to the IOLAN outside of a VPN tunnel. Add VPN Exception Set VPN Exception authentication- type Specify the authentication method that will be used for the L2TP tunnel.
VPN Exceptions 122 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Delete VPN Exception Show VPN Exception host-ip < ipv4/ipv6_address > The IP address of the host that will comm unicate with the IOLAN outside of the VPN tunnel. Field Format: IPv4 or IPv6 address Description Deletes a VPN exception.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 123 T i me Commands Chapter 6 6 This chapter defines all the CLI commands a ssociated with configuring the IOLAN’ s time parameters. Server Commands Set T ime Set T imezone Show Time Show T imezone Description Sets the IOLAN’ s system clock.
SNTP Commands 124 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 SNTP Commands Add SNTP Delete SNTP Set SNTP Description Adds an SNTP server . User Level Admin Syntax add sntp [server-1 < config_ho st >] [server-2 < config_host >] Options server -1 The name of the primary SNTP server from the IOLAN host table.
T ime Commands 125 T ime/Date Setti ng Commands Show SNTP Show SNTP-Info T ime/Date Setting Commands Set Date Set Summertime server -1 The name of the primary SNTP server from the IOLAN host table. V alid with U nicast and Multicast modes, although in Multicast mode, the IOLAN will only accept broadcasts from the speci fied host SNTP server .
T ime/Date Settin g Commands 126 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 Set Summertime Fixed Set Summertime Recurring offset The offset from UTC for your local time zone. Specify in the format of hours hh (valid -12 to +14) and minutes mm (valid 0 to 59 minutes) for the offset from UTC.
T ime Commands 127 T ime/Date Setti ng Commands Show Date Show Summertime end-time The time to end summer time and start stan dard time; uses the format hh:mm for a 24-hour clock (00 :00-23:59). end-week The week to end summer time and start standard time.
T ime/Date Settin g Commands 128 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 129 Administration Commands Chapter 7 7 This chapter defines all the CLI commands associ ated with configuring the IOLAN ’ s ad ministration parameters. Bootup Commands Reboot Reset Reset Factory Save Description Reboots the IOLAN.
TFTP File Transfer Commands 130 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set Bootup Show ARP Show Bootup TFTP File T ransfer Commands Netload Description Specifies remote the TFTP host and pathname for files to be loaded after a IOLAN reboot.
Administration Commands 131 TFTP File T ransfer Commands Net save configuration Specifies that you are going to download a new configuration file to the IOLAN.
Custom Factory Default 132 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Custom Factory Default Netload Set < filename > The complete path and file name fo r the file you are uploading from the IOLA N (this path should be relative to the default path of your TFTP server, wh ich may or may not allow drive letters).
Administration Commands 133 Keys and Certificates Commands Keys and Certificates Commands Netload Description Loads certificates and keys into the IOLAN.
Keys and Certificates Commands 134 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Net save ipsec < tunnel_name > When you config ure an IPsec tunnel with an Authentication Method of RSA Signature , you need to download the RSA key from the remote VPN gateway to the IOLAN for that specific tunnel.
Administration Commands 135 MOTD Commands MOTD Commands Set MOTD Show MOTD Description Specifies the server/file that contains the mes sage of the da y (MOTD) that is displayed when users log into the IOLAN.
MOTD Commands 136 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 137 S t atistics Commands Chapter 8 8 This chapter defines all the CLI commands asso ciated with co nfiguring the IOLAN’ s statistics parameters. Configuration S t atistics Show Net stat Show Net st at S tatistics Description Shows currently used TCP/UDP sockets/ports.
Run-T i me S tatistics 138 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show Modbus St atistics Show Routes Run-T ime St atistics Delete Arp Show Arp Show Serial Uptime Description Shows the Modbus statistics.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 139 IOLAN+ User Commands Chapter 9 9 Y ou can configure the IOLAN us ing the IOLAN+ menu. See the IOLAN+ User ’ s Guide for the command line interface and menu parameters. See IOLAN+ Interface in the IOLAN User ’ s Guide for a list of changes to the IOLAN+ menu.
IOLAN+ 140 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 141 I/O Commands Chapter 10 10 This chapter defines all the CLI commands associat ed with configuring the IOLAN’ s I/O parameters. Global I/O Commands Set IO UDP Description Sets the UDP settings fo r I/O unicast messages.
Set Line 142 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IO Failsafe Set IO Modbus Set IO T emperature-Scale Set Line Set Line Service Description Sets the failsafe (watchdog) settings for I/O. User Level Admin Syntax set io failsafe [mode on|off] [timeout < seconds >] Options mode Enables/disables the Failsafe T imer .
I/O Commands 143 Set IOChannel Set IOChannel Set IOChannel Mode Set IOChannel Digit al I/O Description Sets general I/O channel set tings for the sp ecified channel, these settings are available to all channels and I/O serial pins.
Set IOChannel 144 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Digit al Input Description Sets the Digital input settings for the channel.
I/O Commands 145 Set IOChannel Set IOChannel Digit al Input (Serial Pins) Description Sets the Digital input settings for serial pi ns CTS, DSR, and DCD.
Set IOChannel 146 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Digit al Output latch Latches (remembers) the activity transition ( active-to-inactive or inactive-to-active). The latched status is maintained until it is read. Once it i s read, it will revert to the current status.
I/O Commands 147 Set IOChannel Set IOChannel Digit al Output (Serial Pins) output Specify how the chan nel output will be handled: z Manual —Y ou must manually manipulate the ch annel output. z Pulse —Activates and deactivates the channel out put activity in intervals after it is manually activat ed.
Set IOChannel 148 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Relay Description Sets the Relay output channel settings. User Level Admin Syntax set iochannel < relay_numb.
I/O Commands 149 Set IOChannel Set IOChannel Analog (T rue Analog) Description Sets the Analog input channel settings. User Level Admin Syntax set iochannel < analog_channel > type cu rrent|volt.
Set IOChannel 150 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Analog (T emperature) trigger - level Specify the value that will trigger an ala rm, the measurement is based on the Ty p e and Range that you specify . This value must not fall within the scope of the value used to clear an alarm.
I/O Commands 151 Set IOChannel range Specify the temperature range that you wa nt to measure. For R TD, t he range is: z 1 (Pt100 a=385 -50 to 150C) Th is is the default.
Set IOChannel 152 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel IOExtension clear -mode Specifies whether an act ivated alarm must be Manually cleared, or can be cleared when the input drops below th e specified value (when Tr i g g e r Ty p e is High ) or goes above the specified value (when Tr i g g e r Ty p e is Low ).
I/O Commands 153 Set IOChannel enabled When enabled, the di gital input channel o r DSR/DCD/CTS input serial signal pins can be connected to: z A Digital output or relay (if the I/O model suppo rts re.
Set IOChannel 154 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Set IOChannel Multihost server -initiated tcp-port The TCP Port that the channe l/serial signal pin will use to communicate to another IOLAN or a TCP/ IP application.
I/O Commands 155 Set IOChannel Set IOChannel IOExtension SSL Show IOChannel S t atus Kill IOChannel Description Configures the secure SSL/ TLS connection between the Digital/Relay I/O channel or serial signal pin and the host/IOLAN. For an explanation of the parameters, see Set SSL Line on page 90 .
I/O Channel Control Commands 156 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 Show IO Show IOChannel I/O Channel Control Commands The I/O commands in this section are used to manual ly manage the I/O channels. Digit al Output Description Shows global I/O information (for example, UDP , TruePort, Modbus).
I/O Commands 157 Calibrating Analog I nput (Analog/T empera ture) Digit al Input Relay Analog Input Calibrating Analog Input (Analog/T emperature) Calibrate Analog Reset Calibration Description Manages the Digital input channe l status.
Calibrating Analog I nput (Analog/T empera ture) 158 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 159 Power Commands Chapter 11 11 This chapter defines all the CLI commands a ssociated with configuring the IOLAN’ s power parameters. Power Commands Description Actively controls the RPS plug power .
Power Commands 160 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7.
IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersion 3.7 161 Glossary This chapter provides definitions for IOLAN terms. BOOTP (BOOT strap Protocol) An Internet protocol that enables a diskless workstation to discover its own IP address, the IP address of a BOOTP server on the network, and a file to be loaded into memory to boot the machine.
162 IOLAN SDS/SCS/STS/MDC CLI Reference Guide, V ersio n 3.7 P AP (Password Authentication Protocol) Standard authentication protocol for PPP connections. see CHAP RADIUS (Remote Authentication Dial In Users Services) An open standard network securit y server that communicates wi th the P AP protocol.
Ein wichtiger Punkt beim Kauf des Geräts Perle Systems SDS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Perle Systems SDS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Perle Systems SDS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Perle Systems SDS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Perle Systems SDS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Perle Systems SDS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Perle Systems SDS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Perle Systems SDS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Perle Systems SDS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
