Benutzeranleitung / Produktwartung 1063 des Produzenten Patton electronic
Zur Seite of 67
OnSite 1052 &1063 Series Metro-Optical T ranspor t Access Nodes Getting Star ted Guide Sales Office: +1 (301) 975-1000 T echnical Suppor t: +1 (301) 975-1007 E-mail: support@patton.
Patton Electronics Company , Inc. 7622 Rickenbacker Drive Gaithersburg, MD 20879 USA T el: +1 (301) 975-1000 F ax: +1 (301) 869-9293 Support: +1 (301) 975-1007 W eb: www .patton.com E-mail: support@patton.com Copyright © 2009, Patton Electronics Company .
3 Summar y T able of Contents 1 Product Overview .......................................................................................................................................... 14 2 Application Overview .....................................
4 T able of Contents Summary Table of Contents ........................................................................................................................... 3 Table of Contents ............................................................
5 OnSite Series Getting Started Guide OnSite System Installation ....................................................................................................................................29 Mounting the Chassis to an EIA/TIA 19-Inch Rack ...
6 OnSite Series Getting Started Guide Model OS1052 ......................................................................................................................................................60 Trunk Interfaces ..............................
7 List of Figures 1 OnSite Model 1052 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2 OnSite Model 1063 . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 List of T ables 1 General conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 Mouse conventions . . . . . . . . . . . . . . . . . . . . . . . . . .
9 About this guide This guide describes how to install a P atton OnSite S eries M odel 1052 and1063 Metr o-Optical T ransport Access N ode. For detailed configuration and management instructions, refer to the OnSite 1052 & 1063 S eries Administr ator’ s Refer ence Guide , which is located on the CD-R OM that came with your unit and at www .
10 OnSite Series Getting Started Guide Structure This guide contains the following chapters and appendices: • Chapter 1 describes the OnSite S eries M etro-Optical T ransport Access N odes • Chapt.
11 OnSite Series Getting Started Guide T ypographical conventions used in this document This section describes the typographical conventions and terms used in this guide.
12 OnSite Series Getting Started Guide Safety when using electricity F ollow these guidelines when working on equipment power ed by electricity: • Locate the emergency power-off switch in the r oom in which you are working. Then, if an electrical acci- dent occurs, you can quickly turn off the pow er .
13 OnSite Series Getting Started Guide Electrostatic Discharge Damage Electrostatic discharge (ESD) can damage equipment and impair electrical cir cuitry . I t can occur if electronic printed circuit cards ar e improperly handled and can cause complete or intermittent failures.
14 Chapter 1 Product Over view Chapter contents Introduction ..........................................................................................................................................................15 OnSite Platforms ................
Introduction 15 OnSite Series Getting Started Guide 1 • Product Overview Introduction The OnSite S eries is family of ultra-compact, micro multi-service provisioning platforms (µMSPP s).
Introduction 16 OnSite Series Getting Started Guide 1 • Product Overview Figure 2. OnSite Model 1063 The OS1052 and OS1063 systems have two expansion slots.
Introduction 17 OnSite Series Getting Started Guide 1 • Product Overview Figure 3. OS1052 Base System F igure 2 sho ws the front panel of the OS1063 system. The OS1063 uses a future bus connector for access to the 21 E1 or T1 ports on the base system.
18 Chapter 2 Application Over view Chapter contents OS1052 Application ..............................................................................................................................................19 OS1063 Application ................
OS1052 Application 19 OnSite Series Getting Started Guide 2 • Application Overview OS1052 Application The advanced modular design of the P atton OnSite OS1052 pro vides unequaled flexibility in its class in terms of service offerings, capacity and functional upgrades.
OS1052 Application 20 OnSite Series Getting Started Guide 2 • Application Overview The base OS1052 system is configured with: • 2 STM-1 • 8 E1/T1 • 2 Ethernet • 10/100Base-TX T wo expansion module slots allow increasing system capacity bey ond the initial base configuration.
OS1063 Application 21 OnSite Series Getting Started Guide 2 • Application Overview OS1063 Application The advanced modular design of the P atton OnSite OS1063 pro vides unequaled flexibility in its class in terms of service offerings, capacity and functional upgrades.
OS1063 Application 22 OnSite Series Getting Started Guide 2 • Application Overview The base OS1063 system is configured with: • 2 STM-1 • 21 E1/T1 T wo expansion module slots allow increasing system capacity bey ond the initial base configuration.
23 Chapter 3 Installation Over view Chapter contents Introduction ..........................................................................................................................................................24 Unpacking and Inspection ...
Introduction 24 OnSite Series Getting Started Guide 3 • Installation Overview Introduction This chapter provides the pr ocedures for installing the OnS ite OS-10 system. Unpacking and Inspection Do not unpack the OS-10 system until you ar e ready to install it.
Site Environment 25 OnSite Series Getting Started Guide 3 • Installation Overview Site Environment The OS-10 system can be mounted in a rack or on a wall. The location of the chassis and layout of your equip- ment rack or wiring room are extr emely important for proper system operation.
Planning Your Site 26 OnSite Series Getting Started Guide 3 • Installation Overview • Distribution rack requir ements The following sections pro vide further details for each area. Operating Environment Requirements Y ou need to verify that your site meets all environmental and safety requir ements.
Planning Your Site 27 OnSite Series Getting Started Guide 3 • Installation Overview Power Supply Requirements T o operate your OS-10 equipment safely , follow these requirements: • Ensure that your po wer supply meets the site po wer requir ements of the equipment to be installed.
Planning Your Site 28 OnSite Series Getting Started Guide 3 • Installation Overview Mechanical Recommendations for the Rack The following information will help you plan y our equipment rack configuration: • U se a rack made of steel or aluminum. • Install equipment in the lo wer half of the rack first to avoid making the rack top heavy .
Tools and Equipment for Installation and Maintenance 29 OnSite Series Getting Started Guide 3 • Installation Overview T ools and Equipment for Installation and Maintenance Y ou need the following to.
OnSite System Installation 30 OnSite Series Getting Started Guide 3 • Installation Overview Note T ake care to load the rack so that it is not top heavy . Note Do not co ver vents that would r estrict airflow . Leav e a minimum of a half-rack space above and belo w the OS-10 system for adequate ven- tilation.
OnSite System Installation 31 OnSite Series Getting Started Guide 3 • Installation Overview Note Do not co ver vents that would r estrict airflow . Leav e a minimum of a half-rack space above and belo w the OS-10 system for adequate ven- tilation. 3.
OnSite System Installation 32 OnSite Series Getting Started Guide 3 • Installation Overview Mounting the Chassis on the W all Note When choosing a wall-mounting location, consider the cable limita- tions and the wall structure. U se the four L brackets pro vided for rack mounting to mount the chassis on a wall.
OnSite System Installation 33 OnSite Series Getting Started Guide 3 • Installation Overview Installing the Chassis Ground Connection The OS-10 system chassis requires a r eliable earth ground connection. Y ou must connect the chassis to a reli- able earth ground.
OnSite System Installation 34 OnSite Series Getting Started Guide 3 • Installation Overview Note The DC-to-DC converter has dual power inputs (A and B po wer). The system continues to operate normally if either the A or B power input fails. The system uses natural convection for heat dissipation (that is, it does not use fans).
OnSite System Installation 35 OnSite Series Getting Started Guide 3 • Installation Overview Powering On the OS-10 System with AC Power T o power on the OS-10 system using AC po wer , follo w these steps: 1. Connect the AC po wer cable to the OS-10 system and then to the wall outlet.
OnSite System Installation 36 OnSite Series Getting Started Guide 3 • Installation Overview Figure 13. Wiring the OS-10 System for DC Power 1. Choose an available circuit from a DC po wer source and identify both the positive and negativ e leads for this circuit.
OnSite System Installation 37 OnSite Series Getting Started Guide 3 • Installation Overview 5. Connect the positive lead of the circuit to the return dir ection for “ A” power on the OS-10 system termi- nal block. See wiring 2-A in F igure 7. Note The terminal block indicates the return direction for “ A” power by the letter R.
OnSite System Installation 38 OnSite Series Getting Started Guide 3 • Installation Overview 9. Connect the negative lead of the circuit to the “B” po wer input lead on the OS-10 system terminal block. See wiring 3-B on figure 13 on page 36. Note The terminal block indicates the “B” power lead b y the letter B.
39 Chapter 4 System Management Access Chapter contents Introduction ..........................................................................................................................................................40 General Overview .........
Introduction 40 OnSite Series Getting Started Guide 4 • System Management Access Introduction This chapter provides the pr ocedures for configuring and monitoring the local serial and LAN management (LM) ports, and the inband management channel (IMC) for remote management communications.
Ethernet LAN Management Port 41 OnSite Series Getting Started Guide 4 • System Management Access F igure 15 pr ovides a close-up view of the two management ports. The figure includes the location of the RJ-45 connector pins for both ports. Figure 15.
Serial Management Port 42 OnSite Series Getting Started Guide 4 • System Management Access T able 11 provides the pin assignments for the RJ-45 connector . Serial Management Port The physical connector for the RS-232 SERIAL management port is an RJ-45 connector .
Gaining Access to the System 43 OnSite Series Getting Started Guide 4 • System Management Access Gaining Access to the System There are two ways of gaining access to the system management functions. O ne way is through the SERIAL port and the command line interface (CLI).
Gaining Access to the System 44 OnSite Series Getting Started Guide 4 • System Management Access 8. T ype the following CLI command to save the IP settings (address, net mask, and default gateway)fo.
Web-Based Management Interface 45 OnSite Series Getting Started Guide 4 • System Management Access See “W eb-Based M anagement Interface ” on page 45 for a description of the W eb-based management interface features.
Web-Based Management Interface 46 OnSite Series Getting Started Guide 4 • System Management Access After successful completion of the login, the browser displays the O nSight DM splash screen fr om which you can select the language of your choice (English or Chinese, currently).
Autonomous Alarm Messages 47 OnSite Series Getting Started Guide 4 • System Management Access Autonomous Alarm Messages Y ou can configure the system to generate autonomous alarm messages that can be received and display ed by an SNMP-based network management system (NMS).
Autonomous Alarm Messages 48 OnSite Series Getting Started Guide 4 • System Management Access T o remove an existing SNMP trap r eceiver , follo w these steps: 1. Select a trap receiv er on the SNMP T rap Receivers page. 2. Click on Delete to remo ve the trap receiver .
Engineering Orderwire (EOW) 49 OnSite Series Getting Started Guide 4 • System Management Access Engineering Orderwire (EOW) If the system is equipped with the factory-installed AUX (auxiliary) board, you can use A UX port 1 (AUX 1) for voice communications between two or more inter connected OnSite OS-10 S eries systems.
Engineering Orderwire (EOW) 50 OnSite Series Getting Started Guide 4 • System Management Access Figure 21. Location of signal pins on the EOW port (AUX 1) RJ-11 connector The EO W port supports dual-tone multifrequency (DTMF) signaling to identify EO W stations within an OnSite OS-10 subnetwor k.
Engineering Orderwire (EOW) 51 OnSite Series Getting Started Guide 4 • System Management Access Note In addition to supporting selective calling of EO W stations using the station ID, the EO W also supports a party-line function that allows calling and communicating with all EO W stations at once (party-line function) by dialing *000.
Engineering Orderwire (EOW) 52 OnSite Series Getting Started Guide 4 • System Management Access At this point, the called station begins to ring if another telephone set is connected to the EO W port of that station. Note T o call and communicate with all EO W stations at once (par ty-line function), dial *000.
53 Chapter 5 Contacting Patton for assistance Chapter contents Introduction ..........................................................................................................................................................54 Contact information .
Introduction 54 OnSite Series Getting Started Guide 5 • Contacting Patton for assistance Introduction This chapter contains the following information: • “Contact information ” —describes ho w to contact P atton technical suppor t for assistance.
Warranty Service and Returned Merchandise Authorizations (RMAs) 55 OnSite Series Getting Started Guide 5 • Contacting Patton for assistance Return for credit policy • Less than 30 days: N o Charge. Y our credit will be issued upon receipt and inspection of the equipment.
56 Appendix A Compliance information Chapter contents Compliance ...........................................................................................................................................................57 EMC ........................
Compliance 57 OnSite Series Getting Started Guide A • Compliance information Compliance EMC • EN 55022 Class A • FCC part 15 Class A Safety • EN 60950 • UL 60950 Radio and TV Inter ference T.
Declaration of Conformity 58 OnSite Series Getting Started Guide A • Compliance information If trouble is experienced with this equipment, for repair or warranty information, please contact our company .
59 Appendix B Specifications Chapter contents Model OS1052 ......................................................................................................................................................60 Trunk Interfaces .....................
Model OS1052 60 OnSite Series Getting Started Guide B • Specifications Model OS1052 T runk Interfaces STM-1: G.707, G.783 Optics: G.957 S-1.1, L-1.1 and L-1.2 options Client Interfaces E1: G.703, 75-ohm and 120-ohm options T1: G.703, 100-ohm Ethernet 10/100B ase-TX: 802.
Model OS1052 61 OnSite Series Getting Started Guide B • Specifications Operations Local and remote software do wnload and upgrade (FTP/TFTP) Loopbacks: facility and terminal ALS (automatic laser shutdown): G.
Model OS1063 62 OnSite Series Getting Started Guide B • Specifications Model OS1063 T runk Interfaces STM-1: G.707, G.783 Optics: G.957 S-1.1, L-1.1 and L-1.2 options Client Interfaces E1: G.703, 75-ohm and 120-ohm options T1: G.703, 100-ohm Ethernet 10/100B ase-TX: 802.
Model OS1063 63 OnSite Series Getting Started Guide B • Specifications Operations Local and remote software do wnload and upgrade (FTP/TFTP) Loopbacks: facility and terminal ALS (automatic laser shutdown): G.
64 Appendix C T erms and Acronyms Chapter contents Abbreviations ......................................................................................
Abbreviations 65 OnSite Series Getting Started Guide C • Terms and Acronyms Abbreviations Abbreviation Meaning A AIS Alarm Indication Signal AMI Alternate Mark Inversion AU Administrative Unit AUX A.
Abbreviations 66 OnSite Series Getting Started Guide C • Terms and Acronyms L LCAS Link Capacity Adjustment Scheme LFD Loss of Frame Delineation LOF Loss of Frame LOP Loss of Pointer LP Low-order Pa.
Abbreviations 67 OnSite Series Getting Started Guide C • Terms and Acronyms T TDM T ime Division Multiplexing TIA T elecommunications Industr y Association TIM T race Identifier Mismatch TNV T elec.
Ein wichtiger Punkt beim Kauf des Geräts Patton electronic 1063 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Patton electronic 1063 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Patton electronic 1063 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Patton electronic 1063 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Patton electronic 1063 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Patton electronic 1063 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Patton electronic 1063 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Patton electronic 1063. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Patton electronic 1063 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
