DE
Makita logo
Offizielle Bedienungsanleitung

Makita LS800D

88 Seiten·891 KB·Akkusäge·PDF·ENJA
Makita LS800D
Inhaltsverzeichnis 15 Abschnitte F Scie à coupe d’onglet mixte sans fil Manuel d’instructions · I Sega a quartabuono composta a batteria Istruzioni per l’uso · E Sierra de inglete mixta a batería Manual de instrucciones · P Serra de esquadria composta a bateria Manual de instruções · … AnzeigenAusblenden
Page 1 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 1 · Zum Vergrößern klicken
Seite 1
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 1)
Abb. 1 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…

F Scie à coupe d’onglet mixte sans fil Manuel d’instructions

I Sega a quartabuono composta a batteria Istruzioni per l’uso

E Sierra de inglete mixta a batería Manual de instrucciones

P Serra de esquadria composta a bateria Manual de instruções

Page 2 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 2 · Zum Vergrößern klicken
Seite 2
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 2)
Abb. 2 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 2)
Abb. 3 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 2)
Abb. 4 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 2)
Abb. 5 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Page 3 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 3 · Zum Vergrößern klicken
Seite 3
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 3)
Abb. 6 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 3)
Abb. 7 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 3)
Abb. 8 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 3)
Abb. 9 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Page 4 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 4 · Zum Vergrößern klicken
Seite 4
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 4)
Abb. 10 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 4)
Abb. 11 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 4)
Abb. 12 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 4)
Abb. 13 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Page 5 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 5 · Zum Vergrößern klicken
Seite 5
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 5)
Abb. 14 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 5)
Abb. 15 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 5)
Abb. 16 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 5)
Abb. 17 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Page 6 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 6 · Zum Vergrößern klicken
Seite 6
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 6)
Abb. 18 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 6)
Abb. 19 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Makita LS800D — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions diagram (page 6)
Abb. 20 · F Scie à coupe d’onglet mixte sans fil Manuel d’inst…
Page 7 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 7 · Zum Vergrößern klicken
Seite 7

Symbols The followings show the symbols used for tool. Be sure that you understand their meaning before use.

Symboles Nous donnons ci-dessous les symboles utilisés pour l’outil. Assurez-vous que vous en avez bien compris la signification avant d’utiliser l’outil.

Symbole Die folgenden Symbole werden für die Maschine verwendet. Machen Sie sich vor der Benutzung unbedingt mit ihrer Bedeutung vertraut.

Simboli Per questo utensile vengono usati i simboli seguenti. Bisogna capire il loro significato prima di usare l’utensile.

Symbolen Voor dit gereedschap worden de volgende symbolen gebruikt. Zorg ervoor dat u de betekenis van deze sym- bolen begrijpt alvorens het gereedschap te gebruiken.

Símbolos A continuación se muestran los símbolos utilizados con esta herramienta. Asegúrese de que entiende su sig- nificado antes de usarla.

Símbolos O seguinte mostra os símbolos utilizados para a ferramenta. Certifique-se de que compreende o seu signifi- cado antes da utilização.

Symboler Nedenstående symboler er anvendt i forbindelse med denne maskine. Vær sikker på, at De har forstået sym- bolernes betydning, før maskinen anvendes.

Symboler Det följande visar de symboler som används för den här maskinen. Se noga till att du förstår deras innebörd innan maskinen används.

Symbolene Følgende viser de symblene som brukes for maskinen. Det er viktig å forstå betydningen av disse før maski- nen tas i bruk.

Alla on esitetty koneessa käytetyt symbolit. Opettele näiden merkitys, ennen kuin käytät konetta.

Σύµλα Τα ακλυθα δεί νυν τα σύµλα πυ ρησιµπιύνται για τ µη άνηµα. Βεαιωθείτε τι καταλααίνετε τη σηµασία τυς πριν απ τη ρήση.

❏ Read instruction manual. ❏ Lire le mode d’emploi. ❏ Bitte Betriebsanleitung lesen. ❏Leggete il manuale di istruzioni. ❏Lees de gebruiksaanwijzing. ❏Lea el manual de instrucciones.

❏Leia o manual de instruções. ❏Læs brugsanvisningen. ❏Läs bruksanvisningen. ❏Les bruksanvisingen. ❏Katso käyttöohjeita. ❏∆ιαάστε τις δηγίες ρήσης.

Symbolit

Page 8 of the Makita LS800D user manual — F Scie à coupe d’onglet mixte sans fil Manuel d’instructions
Seite 8 · Zum Vergrößern klicken
Seite 8

❏To avoid injury from flying debris, keep holding the saw head down, after making cuts, until

the blade has come to a complete stop.

❏Pour éviter toute blessure résultant du vol de débris, tenez l’outil avec sa tête dirigée vers

le bas lorsque la coupe est terminée, jusqu’à ce que la lame soit complètement arrêtée.

❏Um Verletzungen durch herausgeschleuderte Teile zu vermeiden, halten Sie den

Maschinenkopf nach Ausführung von Schnitten abgesenkt, bis die Trennscheibe völlig zum Stillstand gekommen ist.

❏Per evitare le ferite causate dalle schegge volanti, mantenere abbassata la testa della

fresa dopo i tagli finché la lama non si è fermata completamente.

❏Na het maken van sneden, moet u de zaagkop omlaag blijven houden totdat het zaagblad

volledig tot stilstand is gekomen, om mogelijke verwonding door vliegende brokstukken te voorkomen.

❏ Para evitar heridas a causa de restos volanderos, después de efectuar los cortes mantenga bajada la cabeza del tronzador hasta que el disco se pare completamente.

❏Para evitar injúrias causadas por fragmentos que se soltem, mantenha a cabeça da serra

para baixo, depois de fazer cortes, até que a lâmina esteja completamente parada.

❏For at undgå tilskadekomst forårsaget af flyvende afskær skal savhovedet holdes nede

efter afskæringen, indtil skiven er helt standset.

❏Håll såghuvudet nedåt, efter avslutad kapning, tills klingan har stannat helt, för att undvika

skador från flygande skräp.

❏For å forhindre skader fra spon og flis som spres omkring, må saghodet holdes nede etter

at kuttene er gjort helt til bladet har stoppet.

❏Estä lentävien roskien aiheuttama loukkaantuminen pitämällä sahan kärkiosa sahauksen

jälkeen alhaalla, kunnes terä on kokonaan pysähtynyt.

❏Για να απφύγετε τραυµατισµ απ ιπτάµενα γρέ!ια, κρατάτε τν κπτη πρς τα

κάτω, αφύ κάνετε την κπή, µέ ρι η λεπίδα να σταµατήσει εντελώς.

❏For your safety, remove the chips, small pieces, etc. from the table top before operation.

❏A des fins de sécurité, débarrassez la table de tous les copeaux et autres petits débris

avant le travail.

❏Zur Sicherheit sollte die Tischplatte vor dem Betrieb von Spänen, Kleinteilen usw. gesäu-

bert werden.

❏Per la propria sicurezza, rimuovere le bave, scorie, ecc., da sopra il tavolo dopo il lavoro.

❏Voor uw veiligheid, verwijder spaanders, brokstukjes, enz. van het tafelblad alvorens het

gereedschap te bedienen.

❏Para su propia seguridad, quite las virutas, pequeÞos trozos, etc., de encima de la mesa

antes de realizar la operaciün de corte.

❏Para sua segurança, retire as aparas, peças pequenas, etc. de cima da bancada antes de

começar a operação.

❏For Deres sikkerheds skyld skal alle metalspåner, små dele og så videre fjernes fra bor-

dets overflade før anvendelse.

❏Ta bort spån, småpartiklar osv. från sågbordets ovansida före användningen, för din egen

säkerhets skull.

❏Av sikkerhetsmessige årsaker må spon, metallstykker, etc. fjernes fra bordet før arbeidet

starter.

❏Poista oman turvallisuutesi vuoksi lastut, pienet kappaleet yms pöydän pinnalta ennen

työskentelyä.

❏Για την ασφάλεια σας , απµακρύνετε τα υπλείµατα, µικρά κµµάτια κλπ. απ τ

τραπέ!ι πρτύ ρησιµπιείσετε τ µη άνηµα.

Page 9 of the Makita LS800D user manual — IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE
Seite 9 · Zum Vergrößern klicken
Seite 9

ENGLISH

Explanation of general view

1 Battery cartridge 2 Push button 3 Socket wrench 4 Wrench holder 5 Blade case 6 Stopper pin 7 Bolts 8 Hex bolt 9 Center cover 10 Safety cover (Safety guard) 11 Arrow 12 Shaft lock 13 Hex bolt (left-handed) 14 Outer flange 15 Saw blade 16 Inner flange 17 Spindle 18 Dust nozzle 19 Dust bag 20 Fastener 21 Kerf board 22 Left bevel cut

23 Straight cut 24 Adjusting bolt 25 Guide fence 26 Turn base 27 Periphery of blade 28 Top surface of turn base 29 Miter scale 30 Pointer 31 Grip 32 Lock lever 33 Lever 34 Loosen 35 Tighten 36 Bevel scale 37 Pointer 38 Arm 39 Vise rod 40 Vise arm 41 Vise knob 42 Holder 43 Holder assembly 44 Vise knob

45 Base 46 Vise shaft 47 Projection 48 Rods 12 49 Lock-off button 50 Handle 51 Switch trigger 52 Lock lever 53 Apply pressure in parallel with blade 54 Set plate 55 Screw 56 Hex bolt 57 Triangular rule 58 Screw 59 45° bevel angle adjusting bolt 60 0° bevel angle adjusting bolt 61 Sub arm 62 Screw 63 Limit mark 64 Screwdriver 65 Brush holder cap

SPECIFICATIONS Model LS800D Blade diameter 210 mm – 216 mm Hole (arbor) diameter

For European countries 30 mm For all countries other than European countries 25.4 mm or 25 mm Max. cutting capacities (H x W) with blade 216 mm in diameter

Miter angleBevel angle 0°45° (left) 0°61 mm x 122 mm45 mm x 122 mm 45° (left and right)61 mm x 85 mm45 mm x 85 mm

No load speed (min-1) 2,000 Dimensions (L x W x H) 528 mm x 430 mm x 486 mm Net weight (with battery cartridge) 9.3 kg Rated voltage D.C.18 V

  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Note: Specifications may differ from country to country.

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE

ENC004-1 1. Before using battery cartridge, read all instruc- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using bat- tery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

Intended use The tool is intended for accurate straight and miter cut- ting in wood.

Safety hints For your own safety, please refer to the enclosed safety instructions.

Page 10 of the Makita LS800D user manual — ENGLISH
Seite 10 · Zum Vergrößern klicken
Seite 10
5. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 6. Do not short the battery cartridge: (1) Do not touch the terminals with any conduc-

10. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 11. Make sure the shaft lock is released before the switch is turned on. 12. Be sure that the blade does not contact the turn base in the lowest position. 13. Hold the handle firmly. Be aware that the saw moves up or down slightly during start-up and stopping. 14. Do not perform any operation freehand. The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. Never use your hand to secure the workpiece. 15. Keep hands out of path of saw blade. Avoid con- tact with any coasting blade. It can still cause severe injury. 16. Never reach around saw blade. 17. Make sure the blade is not contacting the work- piece before the switch is turned on. 18. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade. 19. Wait until the blade attains full speed before cut- ting. 20. Stop operation immediately if you notice any- thing abnormal. 21. Do not attempt to lock the trigger in the ON posi- tion. 22. Shut off power and wait for saw blade to stop before servicing or adjusting tool. 23. Be alert at all times, especially during repetitive, monotonous operations. Don’t be lulled into a false sense of security. Blades are extremely unforgiving. 24. Always use accessories recommended in this manual. Use of improper accessories such as abrasive wheels may cause an injury. 25. Don’t abuse cord. Never yank cord to disconnect it from the receptacle. Keep cord away from heat, oil, water and sharp edges. 26. Do not use the saw to cut other than wood or similar materials. 27. Connect compound miter saws to a dust collect- ing device when sawing. 28. Select saw blades in relation to the material to be cut. 29. Take care when slotting. 30. Replace the kerf board when worn.

tive material. (2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or

rain. A battery short can cause a large current flow, overheating, possible burns and even a break- down. 7. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 8. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 9. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the bat- tery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room tempera- ture at 10°C – 40°C (50°F – 104°F). Let a hot bat- tery cartridge cool down before charging it. 4. Charge the Nickel Metal Hydride battery car- tridge when you do not use it for more than six months.

ADDITIONAL SAFETY RULES FOR TOOL 1. Be aware that this tool is always in an operating condition, because it does not have to be plugged into an electrical outlet. 2. Wear eye protection. 3. Do not operate saw without guards in place. 4. Don’t use the tool in the presence of flammable liquids or gases. 5. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 6. Use only flanges specified for this tool. 7. Be careful not to damage the arbor, flanges (especially the installing surface) or bolt. Dam- age to these parts could result in blade break- age. 8. Make sure that the turn base is properly secured so it will not move during operation. 9. For your safety, remove the chips, small pieces, etc. from the table top before operation.

SAVE THESE INSTRUCTIONS.

Page 11 of the Makita LS800D user manual — Installing or removing saw blade
Seite 11 · Zum Vergrößern klicken
Seite 11

OPERATING INSTRUCTIONS

CAUTION: For all countries other than European countries The inner flange has a 25 mm diameter on one side and a 25.4 mm diameter on the other. The side with 25.4 mm diameter is marked by “25.4”. Use the correct side for the hole diameter of the blade you intend to use. Mounting the blade on the wrong side can result in dangerous vibration.

  • Installing or removing battery cartridge (Fig. 1)
  • Always switch off the tool before insertion or removal of the battery cartridge.
  • To remove the battery cartridge, withdraw it from the tool while pressing the push buttons on both sides of the cartridge.
  • To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Return the safety cover and center cover to its original position. Then tighten the hex bolt clockwise to secure the center cover. (Fig. 9) Release the handle from the raised position by pulling the stopper pin. Lower the handle to make sure that the safety cover moves properly.

Safety cover (Fig. 10) When lowering the handle, the safety cover rises auto- matically. The cover returns to its original position when the cut is completed and the handle is raised. NEVER DEFEAT OR REMOVE THE SAFETY COVER. In the interest of your personal safety, always maintain the safety cover in good condition. Any irregular operation of the safety cover should be corrected immediately. NEVER USE THE TOOL WITH A FAULTY SAFETY COVER. If the see-through safety cover becomes dirty, or sawdust adheres to it in such a way that the blade and/ or workpiece is no longer easily visible, remove the bat- tery cartridge and clean the cover carefully with a damp cloth. Do not use solvents or any petroleum-based clean- ers on the plastic cover.

Socket wrench (Fig. 2) The socket wrench is stored as shown in Fig. 2. When using the socket wrench, pull it out of the wrench holder. After using the socket wrench, return it to the wrench holder.

Bench mounting saw (Fig. 3 & 4) When the tool is shipped, the handle is locked in the low- ered position by the stopper pin. Release the stopper pin by lowering the handle slightly and pulling the stopper pin. This tool should be bolted with four bolts to a level and stable surface using the bolt holes provided in the tool’s base. This will help prevent tipping and possible injury.

Dust bag (Fig. 11) The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit the bag’s entry port over the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection.

Installing or removing saw blade

  • CAUTION:
  • Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade.
  • Use only the Makita socket wrench provided to install or remove the blade. Failure to do so may result in overtightening or insufficient tightening of the hex bolt. This could cause serious injury to operator or others in the general vicinity of the tool.

Positioning kerf board (Fig. 12 & 13) This tool is provided with the kerf boards in the turn base. The kerf boards are factory adjusted so that the saw blade does not contact the kerf boards. Before use, adjust the kerf boards as follows: First, remove the battery cartridge. Loosen the all screws (2 each on left and right) securing the kerf boards. Re- tighten them to the extent that the kerf boards can be easily moved by hand. Lower the handle fully and push in the stopper pin to lock the handle in the lowered position. Adjust the kerf boards so that the kerf boards just contact the sides of blade teeth slightly. Tighten the screws (do not tighten firmly). After adjusting the kerf boards, release the stopper pin and raise the handle. Then tighten the all screws securely.

Lock the handle in the raised position by pushing in the stopper pin. (Fig. 3) To remove the blade, use the socket wrench to loosen the hex bolt holding the center cover by turning it coun- terclockwise. Raise the safety cover and center cover. (Fig.5) Press the shaft lock to lock the spindle and use the socket wrench to loosen the hex bolt (left-handed) clock- wise. Then remove the hex bolt, outer flange and blade. (Fig. 6) To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. Install the outer flange and hex bolt, and then use the socket wrench to tighten the hex bolt (left- handed) securely counterclockwise while pressing the shaft lock. (Fig. 7 & 8)

Page 12 of the Makita LS800D user manual — Securing workpiece
Seite 12 · Zum Vergrößern klicken
Seite 12

Maintaining maximum cutting capacity (Fig. 14 & 15) This tool is factory adjusted to provide the max. cutting capacity for a 216 mm saw blade. When using a saw blade other than 216 mm saw blade, adjust the lower limit position of the blade as follows: First, remove the battery cartridge. Lower the handle completely. Use the socket wrench to turn the adjusting bolt until the periphery of the blade extends slightly below the top surface of the turn base at the point where the front face of the guide fence meets the top surface of the turn base. With the battery cartridge removed, rotate the blade by hand while holding the handle all the way down to be sure that the blade does not contact any part of the lower base. Re-adjust slightly, if necessary.

Securing workpiece

WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. PERSONAL INJURY MAY ALSO RESULT. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. 1. Vertical vise (Fig. 19) The vertical vise can be installed in two positions on either the left or right side of the guide fence, or the holder assembly (optional accessory). Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod. (Note: When using the holder assembly, install it on the holder as shown in Fig. 19.) Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. Make sure that no part of the tool contacts the vise when lowering the handle fully. If some part contacts the vise, re-position the vise. Press the workpiece flat against the guide fence and the turn base. Posi- tion the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. The max- imum thickness of workpieces which can be secured by the vertical vise is 61 mm. 2. Horizontal vise (optional accessory) (Fig. 20 & 21) The horizontal vise can be installed on either the left or right side of the base. By turning the vise knob counterclocwise, the screw is released and the vise shaft can be moved rapidly in and out. To grip work- pieces, turn the vise knob gently clockwise until the projection reaches its topmost position, then fasten securely. If the vise knob is forced in or pulled out while being turned clockwise, the projection may stop at an angle. In this case, turn the vise knob back counterclockwise until the screw is released, before turning again gently clockwise. The maximum width of workpieces which can be secured by the horizontal vise is 122 mm. 3. Holders and holder assembly (optional accessory) The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally. Install them as shown in Fig. 22. Then tighten the screws firmly to secure the holders and the holder assembly. (Fig. 22) When cutting long workpieces, use the holder-rod assembly (optional accessory). It consists of two holder assemblies and two rods 12. (Fig. 23)

Positioning for adjusting the miter angle (Fig. 16) The turn base turns up to 52° to the left and right. Loosen the grip by turning counterclockwise. Turn the turn base while pressing down the lock lever. When you have moved the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise.

  • CAUTION:
  • When turning the turn base, be sure to raise the handle fully.
  • After changing the miter angle, always secure the turn base by tightening the grip firmly.

Positioning for adjusting the bevel angle (Fig. 17 & 18) The saw blade tilts up to 45° to the left. To adjust the bevel angle, loosen the lever at the rear of the tool. Push the handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel scale. Tighten the lever to secure the arm.

  • CAUTION:
  • When tilting the saw blade, be sure to raise the handle fully.
  • After changing the bevel angle, always secure the arm by tightening the lever.
Page 13 of the Makita LS800D user manual — Operation
Seite 13 · Zum Vergrößern klicken
Seite 13

Switch action (Fig. 24)

  • CAUTION:
  • During a bevel cut, it may create a condition whereby the piece cut off will come to rest against the side of the blade. If the blade is raised while the blade is still rotating, this piece may be caught by the blade, causing fragments to be scattered around which is dangerous. The blade should be raised ONLY after the blade has come to a complete stop.
  • When pressing down the handle, apply pressure in parallel with the blade. If a force is applied perpendicularly to the turn base or if the pressure direction is changed during a cut, the precision of the cut will be impaired. 4. Compound cutting Compound cutting is the process in which a bevel angle is made at the same time in which a miter angle is being cut on a workpiece. Compound cutting can be performed at angle shown in the table below.
  • CAUTION:
  • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
  • When not using the tool, remove the lock-off button and store it in a secure place. This prevents unauthorized operation.

To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, press in the lock-off button and pull the trigger. Release the switch trigger to stop.

Lock lever (Fig. 25)

For European countries only When cutting, push the lock lever to the left to release the handle from the raised position. When the cut is com- pleted, release the lock lever after returning the blade to its fully elevated position. The handle will be automati- cally locked in the raised position.

Miter angle Bevel angle

Left and right 45° Left 0° – 45°

Operation

Left and right 52° Left 0° – 40°

  • CAUTION: Do not apply excessive pressure on the handle when cutting. Too much force may result in overload of the motor and/or decreased cutting efficiency. 1. Press cutting (Fig. 26)
  • Workpieces up to 61 mm high x 122 mm wide can be cut in the following way.
  • Secure the workpiece with the vise. Switch on the tool and wait until the blade attains full speed before lowering gently into the cut. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position. 2. Miter cutting Refer to the previously covered “Positioning for adjusting the miter angle”. 3. Bevel cut (Fig. 27)
  • At a left 45° bevel angle, workpieces up to 45 mm high x 122 mm wide can be cut.
  • Loosen the lever and tilt the saw blade to set the bevel angle. Refer to the previously covered “Positioning for adjusting the bevel angle”. Secure the workpiece with the vise. Switch on the tool and wait until the blade attains full speed. Then gently lower the handle to the fully lowered position while applying pressure in parallel with the blade. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position.

At the miter angle of left 45° and bevel angle of left 45°, workpieces 45 mm high x 85 mm wide can be cut. When performing compound cutting, refer to “Press cutting”, “Miter cutting” and “Bevel cut” expla- nations. 5. Cutting repetitive lengths (Fig. 28) When cutting several pieces of stock to the same length, ranging from 220 mm to 365 mm, use of the set plate (optional accessory) will facilitate more effi- cient operation. Install the set plate on the holder as shown in Fig. 28. Align the cutting line on your work- piece with either the left or right side of the groove in the kerf board, and while holding the workpiece from moving, move the set plate flush against the end of the workpiece. Then secure the set plate with the screw. When the set plate is not used, loosen the screw and turn the set plate out of the way.

Carrying tool (Fig. 3 & 29) Make sure that the battery cartridge is removed. Secure the blade at 0° bevel angle and the turn base at 52° miter angle to the right. Lower the handle fully and lock it in the lowered position by pushing in the stopper pin. Carry the tool by the carrying grip as shown in Fig. 29.

Page 14 of the Makita LS800D user manual — ACCESSORIES
Seite 14 · Zum Vergrößern klicken
Seite 14

MAINTENANCE

Replacement of carbon brushes (Fig. 36 & 37) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

Adjusting the cutting angle This tool is carefully adjusted and aligned at the factory, but rough handling may have affected the alignment. If your tool is not aligned properly, perform the following: 1. Miter angle Loosen the grip which secures the turn base. Turn the turn base so that the pointer points to 0° on the miter scale. Then turn the turn base slightly clock- wise and counterclockwise to seat the turn base cozily in the 0° miter notch. (Leave as it is if the pointer does not point to 0°.) Loosen the four hex bolts securing the guide fence using the socket wrench. (Fig. 30) Lower the handle fully and lock it in the lowered posi- tion by pushing in the lock pin. Square the side of the blade with the face of the guide fence using a trian- gular rule, try square, etc. Then securely tighten the hex bolts on the guide fence in the order from right side. (Fig. 31) Make sure that the pointer points to 0° on the miter scale. If the pointer does not point to 0°, loosen the screw which secures the pointer and adjust the pointer so that it will point to 0°. (Fig. 32) 2. Bevel angle i) 0° bevel angle

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.

To maintain product safety and reliability, repairs, mainte- nance or adjustment should be carried out by a Makita Authorized Service Center.

ACCESSORIES

If you need any assistance for more details regarding these accessories, ask your local Makita service center.

  • Dust bag
  • Holder
  • Socket wrench 10
  • Triangular rule
  • Lock-off button (Switch button)
  • Vertical vise
  • Carbide-tipped saw blade
  • Safety goggle
  • Holder-rod assembly
  • Vise assembly (horizontal vise)
  • Set plate
  • Holder assembly
  • Various type of Makita genuine batteries and chargers
  • Battery cover

Lower the handle fully and lock it in the lowered position by pushing in the lock pin. Loosen the lever at the rear of the tool. Turn the 0° bevel angle adjusting bolt (lower bolt) on the right side of the arm two or three revolutions counterclock- wise to tilt the blade to the right. (Fig. 33) Carefully sqaure the side of the blade with the top surface of the turn base using the triangular rule, try square, etc. by turning the 0° bevel angle adjusting bolt clockwise. Then tighten the lever securely. (Fig. 34) Make sure that the pointer on the sub arm points to 0° on the bevel scale on the arm. If it does not point to 0°, loosen the screw which secures the pointer and adjust the pointer so that it will point to 0°. (Fig. 35) ii) 45° bevel angle

Adjust the 45° bevel angle only after performing 0° bevel angle adjustment. To adjust left 45° bevel angle, loosen the lever and tilt the blade 45° to the left. Make sure that the pointer on the sub arm points to 45° on the bevel scale on the arm. If the pointer does not point to 45°, turn the 45° bevel angle adjusting bolt (upper bolt) on the right side of the arm until the pointer points to 45°. (Fig. 33)

Frage zu Makita LS800D stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita LS800D

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita LS800D PDF-Anleitung

88 Seiten·891 KB·Akkusäge·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…