Benutzeranleitung / Produktwartung NVR-0216 des Produzenten LevelOne
Zur Seite of 71
User Manual V er . 1.1 NVR-0204/0208/0216 4-CH/8-CH/16-C H Netw ork Video Recorder.
English Use r ’ s Manual English Use r ’ s Manual LevelOne Network Video R ecorder Table of Contents Copyrights, T rademarks & G PL 3 System Requi rements 4 Product Desc ription 5 Hardware Illust ration 6 I/O Ports and RS-485 7 LEDs Definitio n 8 Install Hard Di sk 9 Connect to t he NVR 12 1.
English Use r ’ s Manual LevelOne Network Video R ecorder Copyrights , Trademarks & GPL Copyright © 2 0 0 9 D i g i t a l D a t a C o m m u n i c a t i o n s G m b H . Trademarks LevelOne NVR-0204/0208/0216 Network Video R e corder (NVR) is a registered trademark o f Digital Data Communications GmbH.
.
5 English Use r ’ s Manual LevelOne Network Vid eo R ecorder System Requirements The fo llowing are minimum system requirements for the system to op er ate LevelOne Network Video Recorder (NVR): Ope.
6 English Use r ’ s Manual Product Description The LevelOne Network Video Recorder is designed for use w ithin a surveillance system, and performs recordings and playbacks pictures fro m network cam er as in the sy stem.
7 English Use r ’ s Manual Hard w are Illustr ation (Front) 6 LevelOne NVR Se ries Network Vid eo R ecorder.
8 English Use r ’ s Manual I/O Ports and RS-485 (Rear) Pin Signal 1 DCIN 2 GND 3 ~ 10 Alarm input 11 Out1 12 Out2 13 Out3 14 Out4 15 RS485+ 16 RS485- 7 LevelOne NVR Se ries Network Vid eo R ecorder.
9 English Use r ’ s Manual LEDs Definition Green Solid green when the hard disk is mounted and being accessed Red Solid red for disk fail HDD x 2 Amber Solid amber when disk is full Blinking when recycling Amber Solid amber for activity on a 1G bps network.
10 English Use r ’ s Manual Install Hard Disk Start b y removing the screws on the side: Push the top housing forward Then lift it up . The NV R supports S ATA I or SATA I I hard disks .
1 1 English Use r ’ s Manual R emov e the hard drive cov er plate Pull out the hard drive tr ay holder Place the hard driv e on the tra y and p ush it inward to se cure the hard drive 10 LevelOne NV.
English Use r ’ s Man ual LevelOne Network Vid eo R ecorder Connect the SA T A cab le to the hard driv e Put the hard drive tr ay cover plate back Place the top housing back and secure it with the b.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Connect to the NVR There are various ways y o u ca n co nnect to the NVR and below are the suggested methods for different network setup: . The NVR is placed in a netw ork with a DHC P serv er: Conn ect to the NVR by using “Search NVR” Utility .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Once the installation is c omplete, check the “Launch the Search AP” option and click “Finish”: The s earch should start automatica.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Y ou wi ll be prompted for th e NVR ’ s login inf ormation be fore proceeding to change device’ s IP address.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder A ccess NVR w ith its default IP address The NVR come s with a p re-configured static IP “ 192.168.101.50 ” . Howev er , it is only u sed when there is no DHCP server presented in the network.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1. Live Vie w NVR-0216 Camera List PTZ Control Live Video Live Video Control Buttons NVR-0208 The 8 channel NVR comes with an 8-video split window view with one v ideo displays o n a larg er wi ndow .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder NVR-0204 The “Live View” page provides the follow ing functions: . R etriev e camera’ s video stream . R etriev e camera’ s status . P erform Live Sequence Viewing . PTZ Control . P erform PTZ Preset Sequence viewing .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.1 Retrieve camera’s video stream The camera list is expanded and displayed on the Liv e View page. . Click “ All ” t o display vid eos in the 8-v ideo mode (NVR-0208) o r 16 - video mode (NVR-0216) .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.3 Perform Sequence Viewing Sequence view is a f unction that a llows you to view multiple video streams from certain camer as in sequence automatically with having to select them one by one.
Engli sh Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.4 PTZ Control PTZ control provides functions to pan, tilt, zoom a PT Z camera as w ell as the ability to adjust camera focus and iris Camera(s) that are currently being select ed for live viewing will be l isted in the P TZ drop-down menu.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.5 Perform PTZ Preset View ing There are three functions provided in the “Preset” se ction: .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder A uto Pa n Viewing Start b y selecting a PTZ camera from the drop-down list: Use the Auto P an Control buttons to pan right, left and stop auto pan Autopan P an Left Stop pan Certain cameras do not support bidirectional pan movements.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.6 Live Video Control Buttons Each live video window comes with control b uttons wi th functions described below: T ake a snapshot of a li.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Take a snapshot of a live video T o take a snapshot of a live video, click the button an d the snapshot of the video will be display ed in .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Full Screen View of a Live Video T o view a video in f ull screen, click t he button. T o exit f ull screen video, double-click anyw here on the video. Turn O n/Off A udio of a Live Video Y ou ca n retrieve audio f rom a particular camera.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 1.7 Change Web UI Display Language Y ou can change th e web UI display lan guage f rom the current login username link lo cated at the upper-ri ght hand co rner .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 2. Playba ck Methods to sear ch playback Playback video contro l buttons Channels to b e played back Playback video Playback is a fun ction that allows you to play o ne or more vi deos that were previously recorde d by a chosen recording method or due to an event trigger .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 2.1 Methods to Search Pla y back Vide os The NVR offers three methods to quickly help users find videos that were previously recorded: . Search by time: Specify a time rang e and search videos recorded within that range .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder . R esults will the n be displayed in a “Date/Ch annel” table and box es marked in blue represent videos found in those dates: .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder . Click on t he ce ll box again will start playing ba ck the videos if y ou have reached the end of search results: . Videos found f rom other camer as that were reco rded at the same time will also be played.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Search by event . Start by selecting which channel(s) you w ould like to p erform a search on: * Selected cha nnels will be mark ed in red . Select “Search by ev ent” from the “ Search Method” drop-down list and click “Go” to start the search: .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder . Y ou may a lso specify a new start time to search and display results from then on. Y ou can restrict the number of results to be displayed at once (max.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Search by event (Most Recent) This function quickly d isplay s the most recent event recordings f rom the selected ch annels, displaying th e mo st recent result top down.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 2.2 Export Playback Videos to AVI Files User can export the recorded p lay back videos stored on NVR-0216 to a local computer and save them in A V I file format. The files can then be p lay ed on the PC by a 3rd party m edia play er such as VLC play er or W indows Me dia player .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Specify the starting and e nding hours of the video b y entering numbers in the text boxes Hit the “Start ” button to start exporting.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3. Sy stem Setup 3.1 System Configurations The “S ystem Configur ations” page provides u sers o ptions to setup the device quickly and properly .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder By default, the recorder is set t o obtain IP address from DHCP server , it sh ould be s ufficient in most network environments, a nd most likely you sh ould n ot need to alter anything in this page.
Engli sh Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.1.2 Time and Date Set the time and date by se lecting the time zone according to y our lo cation.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.1.3 User Account The recorder can be accessed by m ultiple users simultaneously . Y ou can add, remove, and e dit users by usin g options provided in this page to keep user information organized.
menu name English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.1.4 Group Privilege Group Privilege is where you can create multiple customized acc ess po licies for situations if you need the recorder to be accessed by users other than the administrator .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Choose what t ype of privilege you would like this group to have f rom the “Privilege T ype” drop -down menu Its access privilege will then be display ed.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.1.5 Disk Setup Once you install a hard disk to th e recor der , you w ould need to initialize it so that it can be ready for recording.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.2 Channel Configurations 3.2.1 Add a Camera The NVR provides two options for ad ding a new camera. Users have the option to let the reco rder automatically fin d the c amer as or it is possible to enter camera’ s information and add it manually .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 2. After t hat, the search should begin and its status should be displ ay ed: 3. F ou nd cameras should be listed a nd simply select a camera f rom the list and press “Configure” 4. Its corresponding information should be d isplay e d in the “Cam er a Information” section.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder If cameras are mar ked with “*” in the search res ult, it means those cam eras are already con figured and connecte d to NVR-0216 .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.2.2 OSD Settings The OSD (On Screen Display) allows users to add informational text message and embed it onto the video. By d efault, this f unction is turned off . T o a dd texts to one or more videos, 1.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.2.3 PTZ Preset Settings The recorder supports PTZ camer as and can set multiple p reset points o r retrieve and man age preset po ints that are set in the cam er a. T his is helpful if you need to monitor mu ltiple spots in one area f rom a particular camera.
English Use r ’ s M anual LevelOne Network Vid eo R ecorder 3.2.4 PTZ Preset Sequence Once you have m ultiple preset p oints def ined for a came r a, it is conv enient fo r monitoring to set up the sequencing viewi ng among those preset point and let the recorder automatically switch between them for you.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.2.5 E-Map Monitor E-Map monitor is a function th at alerts users w henever there is an ev ent triggered (e.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Then click and dr ag the camer a icon to m ov e the camera to define its location. Access the E-Map M onitor page from t he up per- right h.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.3 Event Configurations The “Event Configurations” section allows use rs to d efine conditions that constitute an event, i ts correspond ing trigger action and when it will be triggered.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Trigger action Now tha t you have the event trigger duration and interv al def ined, choose what action to be taken during an event trigger.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder The recorder does not c ontrol camer a’s input or output ports in a way to let y ou pair recorder itself with a cam era’s input or output p ort for ev ent receiving or triggering.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.3.3 Event Servers Event servers are t o be used with event trigger act ions. In case of unus ual motion detected by the camera or a disk f ailure, the recorder can send notification with th e acceptable f ormat (image/t xt) to a destined event serv er according to the conf ig ur ation.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 4. Enter the username and password of the FT P serv er if it’s required 5. Check “Use Passiv e Mode” if it’s required or leav e it unchecked to use active mode 6.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Configuring an HTTP s erver 1. Start by giving it a name as well 2. Enter the hostname or the IP add ress of the HT TP server 3. Enter the port that ’ s used to communicate with the server 4.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Configuring an SMTP server 1. Enter the hostname or the IP add ress of the SMTP serv er 2. Enter the port of the SMTP server 3. Specify the sender’ s name in the “Sender ’ s name” field 4.
E nglish Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.3.3 Event Triggers W e have finished defining how an event wil l be triggered and w hich serv ers will be receiving notifications in the pre vious two sect ions, n ow we can finis h up the event configur ation by setting: .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder . Define which system ev ents should trigger the recorder to send out notifications . Define how the notifications will be sent and where t.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.4 Recording Configurations The “recording configur ations” gives use rs the over all control of how and when a reco rding is performed and the quality of different types of re cordings performed on e ach channels.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder The “recording configur ations” giv es use rs the over all contro l of how and when a reco rding is performed and the qua lity of different types of recordings performed on e ach channels.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.4.2 Schedule Recordi ng Here y ou ca n define the time range of the schedule reco rding for all channels. To c onfigure a schedule recording: 1. Use the “Camera” drop-down menu and select a camer a first 2.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3. Y ou can also u se the “Quick Configuration” to define recording time r ange inst ead of clicking c ell boxes one by o ne on th e time table.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.5 System Options Sy stem O ptions gives use rs a glance of t he ov erall system sta tus and allows users to perform main tenance tasks such as upgrading firmware, restore/backup device settings or reboo t device ….
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.5.2 Logs and Reports “Logs and R eports” k eeps a record of what’ s been happening to the device and provides basic information for troubleshooting 3.5.3 Maintenance “Maintenance” provides functions for users to: .
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Reboot the NVR R eboot NVR-0216 after you upload a n ew f irmw are. Y ou would need to manually reboot t he system for the new f irmw are to take effect.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder Reset the NVR to Factory Default T o rese t the recorder back to its factory d efault, click “Default” button and begin the process: Th.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder 3.5.4 DO Status This is where you can get the curre nt status of t he NVR-0216 digital ou tput ports. Y ou can also change their status from this page. 3.5.5 Disk Status “Disk Statu s” gives you more detailed information of the h ard drive that is currently installed in the NVR.
English Use r ’ s M anual LevelOne Network Vid eo R ecorder 3.5.6 Ups Configuration Connect the UPS to the NVR ’s DI/DO port for se nding and receiving signals between the UPS and the NVR. Re fer to the diagram below to connect the UPS with its RS-232 interface to the NVR ’ s DI/DO po rt.
English Use r ’ s Manual LevelOne Network Vid eo R ecorder NVR recording time table for reference (it maybe different test res ult with each env ironment) 70 LevelOne NVR Se ries Network Vid eo R ec.
Ein wichtiger Punkt beim Kauf des Geräts LevelOne NVR-0216 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie LevelOne NVR-0216 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für LevelOne NVR-0216 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von LevelOne NVR-0216 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über LevelOne NVR-0216 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon LevelOne NVR-0216 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von LevelOne NVR-0216 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit LevelOne NVR-0216. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei LevelOne NVR-0216 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
