Benutzeranleitung / Produktwartung Cisco 12406 des Produzenten Cisco Systems
Zur Seite of 340
Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Cisco 1 20 06 and Cisco 1 2406.
THE SPECIFICA TIONS AND INFORMA TION REGARDIN G THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WIT HOUT NO TICE. ALL ST A TEMENTS, INFORMA TION, AND RECOMMEND A TION S IN THIS MANUAL ARE BELIEVED TO BE A CCURA TE BUT ARE PRESENTED WITHOUT W ARRANTY OF ANY KIND, EXPRESS OR IMPL IED.
Cisco 12006 and Cisco 12406 Router Installation and Conf iguration Gui de Copyright © 20 01-2006, Cisco Systems, Inc. All r ights reserved. CCVP , the Cisco logo, and W elcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the W ay W e W ork, Liv e, Play , and Learn is a service mark of Cisco Systems, Inc.
.
v Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 CONTENTS Preface xiii Audience xiii Purpose xiii Organization xiv Document Conventions xv Obtaining Documentation xvi Cisco.
Contents vi Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Switch Fabric Card Slots 1-8 Alarm Card Slots 1-8 Chassis Backplane 1-8 Power 1-9 Cooling 1-9 Multigig.
vii Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Contents Technical Specifications 1-52 CHAPTER 2 Preparing for Installation 2-1 Tools and Equipment 2-2 Safety .
Contents viii Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Connecting to the Co nsole and Auxiliary Ports 3-14 GRP Console and Auxilia ry Ports 3-14 PRP Consol.
ix Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Contents Formatting a Flash Memory Card 3-67 Specify a Boot Image 3-68 Flash Memory Console Com mands 3-69 Booti.
Contents x Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Upgrade the FPGA Image on a Line Card 5-7 Using the diag Command 5-8 Cisco 12000 Series Route r Line Ca.
xi Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Contents Adding an RP or Line Card 6-51 Installing a Line Card Cable-Management Bracket 6-52 Reconnecting Cables.
Contents xii Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 I NDEX.
xiii Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Preface Audience The Cisco 12006 and Cisco 12406 Rou ter Installation and Conf igur ation Guide is written for hardware in stallers and syst em adminis trators of Cisco routers.
xiv Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Organization The Cisco 12006 and Cisco 12406 Rou ter Installation and Conf igurat ion Guide contains the follo wing chap ters, appendix, and index.
xv Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Document Conventions This publication u ses the follo wing con ventions: • Ctrl- represents the key labeled Contr ol . For e xample, the key combination Ctrl-z means hold do wn the Control ke y while you press the z key .
xvi Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T imesaver Means the described action saves time . Y ou can sa ve time by performing the action described in the paragrap h. War ni ng This warning symbol means danger .
xvii Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Product Documentation DVD Cisco documentation and additi onal lite rature are av ailable in the Product Documentation D VD package, which may ha ve shipped wit h your product.
xviii Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Instructions for o rdering documentation using the Ord ering tool are at this URL: http://www .cisco.com/uni vercd/cc/td/ doc/es_inpck/pdi.htm • Nonregist ered Cisco.
xix Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 A current list of security ad visories and notic es for Cisco products is available at this URL: http://www .
xx Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The link on this page has the curr ent PGP ke y ID in use. Obtaining Technical Assistance Cisco T echnical Support pro vides 24-hour -a-day aw ard-winning technical assistance.
xxi Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Submitting a Service Request Using the online T A C Service Request T ool is the fastest w ay to open S3 and S4 service requests. (S3 and S4 service request s are those in which your n etwork is minimally impaired or fo r which you require product information .
xxii Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Se verity 3 (S3)—Op erational performance of your n etwork is impai red, but most busin ess operations remain functional . Y ou and Cis co will commit resourc es during normal business hours to rest ore service to s atisfactory levels.
xxiii Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 solve t hem, using real-world case studies and b usiness strategies t o help readers make sound technology in ves tment decisions. Y ou can access iQ Magazine at this URL: http://www .
xxiv Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
CH A P T E R 1-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 1 Product Overview This chapter pro vides an ov ervie w of the Cisco 12006 and Cisco 12406 series routers.
Chapter 1 Product Overview Product Description 1-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 These two router models are d ifferentiated by the switching cap acity of the switch fabric installed i n the router: • Cisco 12006 Router —2.
1-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Product Description Figur e 1 -1 Cisco 12006 and Cisco 12406 rout er (Fr ont V iew) W ith a chassis height of 18.5 inches (46.9 cm), four Cisco 12006 and Cisco 12406 routers can be installed in a sin gle standard 7-foot (2.
Chapter 1 Product Overview Product Description 1-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Cisco 12006 and Cisco 12406 rout ers hav e the follo wing key feat ures: • Route Processor (RP)—Slot 5 (bottom slot ) is the r ecommended slot for the first RP .
1-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Product Description • All power modules a nd other field repl aceable units (FRU s), e xcept for the air blower module and the power distribution unit (PDU), can be removed from the front of the chassis.
Chapter 1 Product Overview Product Description 1-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 1 -2 Cisco 12006 and Cisco 12406 rout er (Rear View) • Fiber Cable Management—Fiber cable management wit h support for high-density fiber Fast Ethernet (FE) ports.
1-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Physical and Functional De scription Physical and Functional Description The main ph.
Chapter 1 Product Overview Chassis 1-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Switch Fabric Card Slots The switch fabric circuitry resides in fi ve fabric card slots: two for CSCs and thre e for SFCs. (See Figure 1-1 .
1-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Chassis Power Because a Cisco 1200 6 or Cisco 12406 Router can be conf igured with e.
Chapter 1 Product Overview Multigigabit Crossb ar Switch Fabric 1-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Multigigabit Crossbar Switch Fabric Cisco 12006 and Cisco 12406 r outer switch fab ric circuity provides synch ronized gigabit-speed interconnect ions for the line cards and the RP .
1-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Multigigabit Crossbar Switch Fabric • System clock—The system cl ock synchronizes data transfers between line cards or between the RP and a line card, through the switch fabri c.
Chapter 1 Product Overview Multigigabit Crossb ar Switch Fabric 1-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Switch Fabric Switching Capacity and Router Type The Cisco 12006 Router is based o n a 2.5-Gbps switch fabric, wh ere each CSC or SFC provides a 2 .
1-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Maintenan ce Bus Maintenance Bus The Cisco 12006 and Cisco 12406 rout er maintenance bus and MBus modules manage the maintenance functions of the syst em.
Chapter 1 Product Overview Maintenance Bus 1-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Code Download A portion of the line car d operating softw are can be downloaded from the RP to the line card ove r the MBus.
1-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors Route Processors Each Cisco 12006 and C isco 12406 router has one main syst em (or route) processor .
Chapter 1 Product Overview Route Processors 1-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Route Processor Types T wo ty pes of RPs are av ailable for Cisco 1 2006 and Cisco 12406 routers, the Gigabit Route Pr ocessor (GRP), and th e Performance Route Processor (PRP).
1-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors Note GRP route memory conf igurations of 512 MB are compatible with only Product Number GRP-B=. Cisco IOS Release 12.
Chapter 1 Product Overview Route Processors 1-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 1-5 G R P L ayo ut Backplane connector S LO T -0 GIGABIT .
1-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors GRP Memory Components Ta b l e 1-1 lists the memory components on the GRP . Figure 1-5 shows the location of the DRAM and Flash SIMM on the GRP .
Chapter 1 Product Overview Route Processors 1-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Caution T o pre vent memo ry problems, DRAM DIMMs must be 3.3-v olt (V), 60-nanosecond (ns) de vices. Do not install othe r devices in th e DIMM sockets.
1-21 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors Flash memory also functions as a T ri vial File T ransfer Protocol (TFTP) server to allo w other servers to boot remotely from stored imag es or to copy them into their o wn Flash memory .
Chapter 1 Product Overview Route Processors 1-22 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 1 -7 GRP Alphanumer ic LED Displays (P artial F aceplate).
1-23 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors For e xample, when the boot f ield of the software conf iguration .
Chapter 1 Product Overview Route Processors 1-24 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Note EIA/TIA-232 is also re ferred to as RS-232. The auxiliary port i s an EIA/TIA-232 plug (male) that provides a data terminal equipment (DTE) interface.
1-25 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors Performance Route Processor This section provides info rmation about the PRP . The PRP is supported in both the Cisco 12406 Router and the Cisco 12006 Router.
Chapter 1 Product Overview Route Processors 1-26 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The Cisco IOS software images are sto red in Flash memory . T wo types of Flash memory ship with the PRP: 1. Onboard Flash memory—Sh ips as a single in-line memory module (SIMM).
1-27 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors Figur e 1 -9 PRP (Hor izo ntal Orie ntation) 1 Backplane connector.
Chapter 1 Product Overview Route Processors 1-28 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 PRP Memory Components PRP memory options and functi ons are listed in T able 1-4. Note If a single DIMM module is installed, it must be placed in bank 1 (U15).
1-29 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors SDRAM SDRAM stores routing tabl es, protocol s, and netw ork accounting applications, and runs the C isco IOS software.
Chapter 1 Product Overview Route Processors 1-30 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 the Flash disk contai ns the Cisco IOS softwar e image. A 64-MB A T A Flash disk ships by def ault with the PRP . Ta b l e 1-5 lists the supporte d Flash disk sizes and their Cisco product nu mbers.
1-31 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Route Processors At the end of the boot process, the LEDs are controlled by the Cisco IOS software (via the MBus), and the content displaye d is designated by the Cisco IOS software.
Chapter 1 Product Overview Route Processors 1-32 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Flash Disk Slots The PRP includes two Flash disk (PCMCIA) slots. Either slot can support an A T A Flash disk or a T ype 1 or T ype 2 linear Flash memory card.
1-33 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Line Cards Line Cards Cisco 12006 and Cisco 12406 rout ers come pre-installed with the number and type of line cards that you o rdered.
Chapter 1 Product Overview Line Cards 1-34 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 1- 10 S a m p l e L i n e C a r d s H10781 Status LEDs Alphanum.
1-35 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Line Cards Alarm Cards Cisco 12006 and Cisco 12406 routers ha ve tw o alarm card slots.
Chapter 1 Product Overview Line Cards 1-36 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Alarm Output Function The alarm output function co nsists of a group of relays, LEDs, and their associated driv ers connected to an output port on the MBus module.
1-37 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Power Subsystems Power Source Monitoring The alarm card monitors the po wer modules and signals when there is a conditi on outside the normal r ange of operation.
Chapter 1 Product Overview Power Subsystems 1-38 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Note Cisco 12006 and Cisco 12406 ro uters can be eith er A C po wered or DC po wered; the router cannot accept two different ty pes of po wer modules at the same time.
1-39 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Power Subsystems Figur e 1 -12 AC P ow er Distr ibution Unit Depending on whet her the router is configured for nonredundant or redundant po wer operation, the router ships with either on e or two 14-foot (4.
Chapter 1 Product Overview Power Subsystems 1-40 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 AC-Input Power Supply The A C-input po wer supply is a remo vable p ower module that installs in one of the bottom two b ays on the front of the chassis (see Figure 1-1 ).
1-41 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Power Subsystems An A C-input po wer supply (shown in Fi gure 1-13) has the followi.
Chapter 1 Product Overview Power Subsystems 1-42 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • T wo LEDs on the faceplate to pro vide status information. Ta b l e 1-6 summarizes t he function of these indicator s.
1-43 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Power Subsystems Figur e 1 -14 DC Po wer Distr ibution Unit DC-input po wer is connected through the DC PDU on the chassis rear panel.
Chapter 1 Product Overview Power Subsystems 1-44 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 power should be connected to the terminal block. A negati ve lead is connected to the top port, a positi ve lead to the middle port, and a ground lead to the bottom port.
1-45 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Power Subsystems Figur e 1 -16 DC-Input P ow er Entry Modul e A DC-input PEM (sh own in Figure 1-16) has the follo wing features: • A circuit breaker switch on the facepl ate turns the PEM on and of f.
Chapter 1 Product Overview Power Subsystems 1-46 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Three LEDs on the faceplate to provide status information. Ta b l e 1-7 summarizes t he function of these indicator s.
1-47 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Blower Module Power Distribution The router chassis back plane distributes -48 VDC power th roughout the router and to all cards in the card cage s.
Chapter 1 Product Overview Blower Module 1-48 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 If the air temperature inside the RP and line card cage rise s, the system en vironmental monit or shuts down all intern al power to prev ent equipment damage from excessi ve heat.
1-49 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Blower Module • OK—Left LED; Green.
Chapter 1 Product Overview Cable-Management System 1-50 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The air filters are located on the right of th e front side of the chassis. The air filters are housed behind a door that i s spring-loaded in the closed position.
1-51 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 1 Product Overview Cable-Management System On line cards with multiple ports, th e line card cable-manag ement bracket keeps the network interf ace cables organ ized when your remov e and replace the line card.
Chapter 1 Product Overview Field-Replacea ble Units 1-52 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Field-Replaceable Units The field-replaceable units (FR U.
CH A P T E R 2-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 2 Preparing for Installation This chapter pro vides specif ic information about prepari ng your site for the installati on of Cisco 12006 and Cisco 12406 Routers.
Chapter 2 Preparing for Installation Tools an d Equipmen t 2-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Tools and Equipment Cisco 12006 and Cisco 12406 Routers can be installed with a minimum number of tools.
2-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Safety and Compliance General Safety Guidelines • Nev er attempt to lift an object that might be too heavy for you to lift by yourself.
Chapter 2 Preparing for Installation Safety and Compliance 2-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Cisco 12006 and Cisco 12406 Routers wit h an A .
2-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Safety and Compliance Compliance and Safety Information The Cisco 12006 and Cisco 12406 routers are desig ned to meet the regul atory compliance and safety appro val requi rements.
Chapter 2 Preparing for Installation Preventing Electrostatic Disc harge Damage 2-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Hav e a second person help lift t he equipment; av oid lifting the eq uipment alone.
2-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Preventing Electrostatic Discharge Damage Attaching an ESD-Preventive Strap Attach an ESD antistatic strap to your bo dy and to an open metal part of the chassis on the Cisco 12006 and Cisco 12406 Router ( Figure 2-1 ).
Chapter 2 Preparing for Installation Safety with Electricity 2-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Safety with Electricity The line cards, redundant.
2-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines Site Requirement Guidelines This section prov.
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 air is too warm, an o vertemperature condition can occur w ithin the router .
2-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines Equipment Dimensions and Site Layout Figure 2-2 sho ws the footprint and o uter dimensions of the chassis for Cisco 12006 and Cisco 12406 Routers.
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T o help maint ain trouble-free operation, c.
2-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines in the rack. Ensure th at cables from other equip ment do not impair access to the card cages, requiring you to disc onnect cables unneces sarily to perform equipment maintenance or up grades.
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Power Connection Guidelines Cisco 12006 and Cisco 124 06 Routers can be configured w ith either an A C -input power subsystem or a DC-input power subsystem .
2-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines Figur e 2-3 A C P ow er Plugs Ta b l e 2-1 A.
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Power Connection Guidelines for DC-Powered R.
2-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines • On Cisco 12006 and Cisc o 12406 Routers .
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Use a cable lug with two holes at 0.63" (16 mm) centers to connect to the chassis with two 6.
2-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Requirement Gu idelines The dual-hole lug is crimped onto a grounding wire of a wire size and length determined b y your router location and f acility en vironment.
Chapter 2 Preparing for Installation Site Requirement Guidelines 2-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Site Wiring This section presents sit e wiring guidelines for setting up the plan t wiring and cabling at your site.
2-21 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Unpacking and Repacking the Router Most data centers cann ot resolve the in frequent but potentially catastrophic problems just described wi thout pulse meters and other special equipment.
Chapter 2 Preparing for Installation Site Preparation Chec klist 2-22 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Site Preparation Checklist Cisco 12006 and Cisco 12406 Routers co me with a site log. Ke ep this in a common place near the router where anyo ne who performs tasks can ha ve access to it.
2-23 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 2 Preparing for Installation Site Preparation Checklist Ta b l e 2-2 Sample Site Log Date Description .
Chapter 2 Preparing for Installation Site Preparation Chec klist 2-24 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
CH A P T E R 3-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 3 Installing the Router This chapter describes ho w to do the initial installation and setup of Cisco 12006 and Cisco 12406 Routers.
Chapter 3 Insta lling the Router Installing a Router 3-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Installing a Router This section e xplains the procedures.
3-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Installing a Router Installing the Rack-Mount Brackets (Optional) The router ac.
Chapter 3 Insta lling the Router Installing a Router 3-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 3-1 Installing the O ptional Rack-Mou nt Brac ket.
3-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Installing a Router Installing Center-Mount Brackets (Optional) T o install the.
Chapter 3 Insta lling the Router Installing a Router 3-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Tools and Equipment Required Y ou need the following it e.
3-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Installing a Router Installing the Chassis in a Rack This section e xplains ho w to install Cisco 12006 and Cisco 12406 Routers in a rack.
Chapter 3 Insta lling the Router Installing a Router 3-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T o install the chassis in a rack, see Figure 3-3 and follow these steps: Step 1 Mov e the router as close to the installation location as possible without interferi ng with the installation process.
3-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Supplemental Bonding and Grounding Connectio ns Installing the Chassis on a Tabletop or Flat Surface Follo w the steps belo w to install a Cisco 12006 Router or Cisco 1240 6 Router on a tabletop or stable flat surface.
Chapter 3 Insta lling the Router Supplemental Bond ing and Grounding Connec tions 3-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 3-4 Supplemental Bonding and Gr ounding P ort fo r NEBS Compliance Use a dual-hole lug to connect to the chassi s with two 6.
3-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting RP and Line Card Cables Figur e 3-6 Cr imping the Lug Note The thre.
Chapter 3 Insta lling the Router Connecting RP and Line Card Cables 3-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 3 Carefully rout e the interface cable t hro ugh the chassis cable-management bracket and across the card to the card interf ace port; do this for one cable at a time.
3-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting Alarm Card Cables Caution Carefully ad just the cable in the cabl e-management brack ets to pre vent an y kinks or sharp bends in the interf ace cable.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Connecting to the Console and.
3-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports Figur e 3-8 GRP Cons ole DCE and A uxiliary DTE P ort Co nnections Check your terminal documentation to d etermine the baud rate of the terminal you plan to use.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 GRP Console Port Signals The console port on the GRP req uires a straight-through EIA/TIA-23 2 cable.
3-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports Ta b l e 3-2 GRP A uxiliary P or.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 PRP Console and Auxiliary Ports The system console port on t he PRP is a DCE R J-45 receptacle for connecting a data terminal, which you must conf igure.
3-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports Caution The ports labeled Ethernet, 10B ASE-T , T oken Ring, Console, and A UX are safety extra-lo w voltage (SEL V) circuits.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 PRP Auxiliary Port Signals The auxiliary port on the PRP is a DTE, RJ-45 plug for connecting a modem or other DCE de vice (such as a CSU/DSU or another router) to the router .
3-21 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports Figur e 3-1 0 Flash Memory Card .
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-22 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Connecting the GRP to an Ethernet Network This section p rovides information f or conn ecting the GRP to an Ethernet network.
3-23 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports Note The RJ-45 and MII receptacl.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-24 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figure 3-13 shows the pin configuration on the Ethern et RJ-45 receptac le on the GRP .
3-25 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports War ni ng The ports labeled Ethernet, 10BASE-T , T oken Ring, Console, and AUX are safety extra-low voltage (SEL V) circuits.
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-26 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Note Use cables that comply with EIA/TIA-568 standards. (See Ta b l e 3-8 on page 3-29 and Ta b l e 3-9 on page 3-29 for cable recommendatio ns and specif ications.
3-27 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to the Console and Auxiliary Ports PRP Ethernet Connections Figure 3-15 sho ws a PRP RJ-45 receptacle and cable connector .
Chapter 3 Insta lling the Router Connecting to the Consol e and Auxiliary Ports 3-28 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Depending on y our RJ-45 cabling requir ements, use the con nector pinouts sho wn in Figure 3-16 or Figure 3-17 .
3-29 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to an AC Power Source Ta b l e 3-9 lists IEEE 802.3u physical characteristic s for 100B A SE-TX. Connecting to an AC Power Source This section presents the procedure for co nnecting your router to an A C power source.
Chapter 3 Insta lling the Router Connecting to an A C Power Source 3-30 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Caution The A C-input po wer supply weighs 14 pound s (6.4 kilograms). Use tw o hands when handling a po wer supply .
3-31 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to an AC Power Source Figur e 3-18 AC P ow er Distr ibution Unit T .
Chapter 3 Insta lling the Router Connecting to a DC Power Source 3-32 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 2 Locate the two A C power cords and remov e them from their shippi ng packaging. V erify that the A C po wer cords shipped with the po wer supplies are the co rrect type for your site.
3-33 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Connecting to a DC Power Source Figur e 3-19 DC PDU T o connect so urce DC pow.
Chapter 3 Insta lling the Router Connecting to a DC Power Source 3-34 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 3-20 DC PDU Po wer Connect or Block .
3-35 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Power On the Router Power On the Router T o power on th e router , follo w the.
Chapter 3 Insta lling the Router Power On the Router 3-36 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Note In a noisy en vironment, the blo wers might be dif ficult to hear; in that case, place your hand in front of the e xhaust vents at the rear of the chassi s to v erify that the blowers are operating.
3-37 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router Step 6 On the console terminal, verify that the console disp lays the system banner and that the system and all interf aces initializ e successfully .
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-38 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Conditions to Check Before System .
3-39 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router Overview of the Boot Process The ex.
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-40 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Line card cable- management brackets are attach ed to their respecti ve line cards.
3-41 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router RP Alphanumeric LED RP alphanumeric LEDs are loc ated at one e nd of the RP faceplate, near the ejector lev er .
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-42 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 RP Interfaces Using the RP LEDs T .
3-43 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router GRP Interfaces Using the GRP LEDs The GRP faceplate has eight device o r port LED activit y indicators.
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-44 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 As the router boots the Cisco IOS .
3-45 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router Figur e 3-24 PRP LEDs When you star.
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-46 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 If the R OM monitor prompt ( rommo.
3-47 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router Manually Booting the System If your.
Chapter 3 Insta lling the Router IOS Software Configuration for the Router 3-48 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Booting from the Ci sco IOS Softwa.
3-49 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router IOS Software Configuration for th e Router Router Configuration Y ou can perfo.
Chapter 3 Insta lling the Router Cisco IOS User Interface 3-50 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Global Configuration Mode The router can be conf igured manually using the gl obal configurat ion mode through the Cisco IOS command line i nterf ace (CLI).
3-51 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Cisco IOS User Interface R OM monitor m ode is a separate mo de used when the ro uter cannot boot prope rly .
Chapter 3 Insta lling the Router Cisco IOS User Interface 3-52 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Global Configuration Mode Global conf iguration commands appl y to features that af fect the system as a whole, rather than just one protocol or interf ace.
3-53 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es Configuration Changes This section describes ho w to conf igure the router .
Chapter 3 Insta lling the Router Configuration Changes 3-54 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The output sho wn in this example depends on the image versio n of the Cisco IOS software and th e way your rout er is equipped.
3-55 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es Current interface summary Interface IP-Address OK? Meth.
Chapter 3 Insta lling the Router Configuration Changes 3-56 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 interface POS15/0 shutdown no ip address ! interface SDCC15/0 shutdown no ip address ! end [0] Go to the IOS command prompt without saving this script.
3-57 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es Configure IP on this interface?[yes]: The script displa.
Chapter 3 Insta lling the Router Configuration Changes 3-58 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 chapter in the Security Configur ation Guide .
3-59 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es • Protocols to be con f igured T o obtain this i nformation, consult your network adm inistrator .
Chapter 3 Insta lling the Router Configuration Changes 3-60 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Line Card Interfaces Because of the wide v ariety of l.
3-61 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es Note Y ou might ha ve to establish additional config uration parameters for the installed A TM line cards if you want to use all their capabilities.
Chapter 3 Insta lling the Router Configuration Changes 3-62 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 BOOTFLASH: GS Software (GSR-BOOT-M), Version 11.2(18)GS4, EARLY DEPLOYMENT RELE Getty uptime is 22 hours, 15 minutes System returned to ROM by reload System image file is "tftp://xxx.
3-63 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es no service tcp-small-servers ! hostname Router ! enable secret 5 $1$W6K5$W/p5Bq6IPLGJ/hS9VVP1g. enable password twink interface POS1/0 ip address 10.
Chapter 3 Insta lling the Router Configuration Changes 3-64 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Saving the Running Configuration Settings to NVRAM T o.
3-65 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Configuration Chang es ip cef distributed switch ip host biff 10.3.3.254 ! interface Ethernet0 ip address 10.3.1.1 255.888.0.0 no ip mroute-cache ! interface POS1/0 ip address 10.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-66 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Using Flash Memory Cards in the RP This s.
3-67 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP Removing the Flash Memory Card from an RP .
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-68 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T o format a ne w Flash memory card, follow these steps: Step 1 Insert the Flash memory card into slot 0 or slot 1 on the RP .
3-69 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP When you enter the rel o ad command, the specified file ( new .image ) on th e Flash memory card inserted in PCMCI A slot 0 is used to boot the system.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-70 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 slot1:/ Router# cd slot0: Router# pwd slo.
3-71 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP T o remo ve deleted f iles from a Flash me.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-72 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Booting from Flash Memory T o enable boot ing from Flash memory , set the boot f ield in the software confi guration register (bits 3 through 0) to a value between 2 and 15.
3-73 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP T o cop y a file to Flash memory , enter t.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-74 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Copying a Cisco IOS Software Image Y ou c.
3-75 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP Step 4 Reboot the syst em.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-76 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T o cop y a bootable Cisco IOS softw are image between Flash memory cards, follo w these step s: Step 1 Boot the router .
3-77 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP Copying Files Between RP Memory and a Flas.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-78 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 T o copy a configuration f ile named myfi.
3-79 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP An example of the copy startup-conf ig slo.
Chapter 3 Insta lling the Router Using Flash Memory Cards in the RP 3-80 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Copying a Configuration File from RP DRAM.
3-81 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router Using Flash Memory Cards in th e RP 5 1186 May 10 2002 16:56:50 myfile2 919715.
Chapter 3 Insta lling the Router If You Need More Information 3-82 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Locked Blocks in Flash Memory Cards A locked bl.
3-83 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 3 Installing the Router If You Need More Information W e appreciate your comments.
Chapter 3 Insta lling the Router If You Need More Information 3-84 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
CH A P T E R 4-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 4 Troubleshooting the Installation This chapter pro vides troubleshooti ng guidelines for Cisco 12006 and Cisco 12406 Routers.
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 – Flash memory SIMM (NVRAM).
4-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks Ta b l e 4-2 specifies th e content of the boot f ield , which defines a source fo r booting the def ault Cisco IOS software imag e required to run the router .
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Boot Field Settings The four .
4-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks If you enter the boot command .
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Note If a bootable Cisco IOS .
4-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks This command sequence sa ves t.
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Bits in the Software Configur.
4-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks Note If a bootable Cisco IOS s.
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Bit 8—Bit 8 of the softwar e configuration re gister controls the console Break key .
4-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks Bit 13—Bit 13 of the softw are config uration register determin es the system response to a bootload fa ilure.
Chapter 4 Troubleshooting the Installation Performing Other Co nfiguration Tasks 4-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 5 W ithin 5 seconds of turning on the router , press the Break key .
4-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Performing Other Configuration Tasks Step 8 Enter no in response to the system conf iguration dialog pr ompts until the follo wing instruction is displ ayed: Press RETURN to get started! Step 9 Press Return .
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 14 Exit global conf iguration mode by entering Ctrl-Z .
4-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems • Cooling subsystem—Consist s .
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • The RP sends the instructions to each line card t o power up. Each line card processor beg ins to perform its own bo ot process.
4-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems AC-Input Power Supply LEDs Figure 4-1 sho ws the location of the LEDs on t he power supply f aceplate.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Ta b l e 4-6 summarizes the function of these indicators .
4-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems DC-Input Power Ent ry Module LEDs Figure 4-2 sho ws the location of the LEDs on t he DC-input PEM.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Blower Module LEDs Figure 4-3 sho ws the location of the LEDs on t he blower module.
4-21 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems When the system is operating correct ly , you should see these LED states: • OK—Green.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-22 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 LEDs that normally should be on: .
4-23 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems Troubleshooting the Power Subsyste.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-24 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 – For installations i n North Americ a, the A C input p o wer ran ge is between 100 and 240 V A C, with a 20A service.
4-25 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems If the A C po wer source wiring appears t o be okay , but the po wer supply A C LED remains of f, go to Step 3 .
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-26 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 7 If a spare po wer supply is a vailable, repl ace the existing module with the spare.
4-27 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems • If Y es, go to Step 4 . Step 4 T u rn of f the PEM circuit breaker sw itch and check the DC power source: a.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-28 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 7 If a spare PEM is a vailable, repl ace the existing mod ule with the spare. If the OUTPUT OK LED th en goes on, the PEM is working norma lly .
4-29 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems on. If both displays are of f, the RP may not be properly seated in the backplane connector .
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-30 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Ta b l e 4-8 RP Alpha numer ic LED Displa y Messages LED Display 1 1. The messages shown do not indicate a specific sequence .
4-31 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems Troubleshooting the Line Cards Line cards can be installed in slots in th e card cage.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-32 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 EXPT INIT Initialize interrupt han.
4-33 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems Troubleshooting by Using the Alarm Cards The alarm cards are installed in the al arm card slots immediately beneath the clock and scheduler card slots.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-34 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 If there are no faults on the SFCs (SFC 0, SFC 1, or SFC 2), the green LED labeled ENABLED for each SFC should be on, and the yellow LED labeled F AIL for each SFC should be of f.
4-35 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 4 Tr oubleshooting the Installation Problem Solving with Subsystems Troubleshooting the Cooling Subsys.
Chapter 4 Troubleshooting the Installation Problem Solving with Subsystems 4-36 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • The follo wing console monitor.
CH A P T E R 5-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 5 Field Diagnostics for the Cisco 12000 Series Router Field diag nostics are a v ailable for all C.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Diagnostics Overview 5-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Smaller Cisco IOS image.
5-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router FPGA Overview While diagnostics are running, the line card being tested is controlled by the diagnostic software.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router FPGA Overview 5-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The follo wing sample Cisco IOS b oot text sho ws an FPGA upgrade message in bold tex t.
5-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router FPGA Overview Loading muckier/award/c12k-fdiagsbflc-mz.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using Diagnostic s 5-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Field Diag eeprom values: run.
5-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using Diagnostics Note All Cisco Systems field diagnostics images a vailable on Cisco.com are backw ard and forwar d compatible with an y Cisco IOS 12.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • For TFTP boot servers, the source path w ould typically be tftp:// tftp_server_ ip_addr ess/my_dir ectory /c12k-fdiagsbflc-mz.
5-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command Note Starting with Cisco IOS Release 12.0(22)S, the line card f ield diagnostics image is unb undled from the main Cisco IOS image.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 tftp Specifies that the source of the diagnostic image is a TFTP server . This k eyword must be follo wed by the so ur ce-path .
5-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command wait (Optional) Stop s the automatic reloading of the Cisco I OS software on the line card afte r the successful completion of the f ield diagnostic testing.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 update-fpga (Optional) Upda tes flash memo ry with field-pro grammable gate array (FPG A) image( s) from the current f ield diagnostics do wnload image.
5-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command In some cases when field di agnostics indicates a card F AILURE, you may want to bring the line card back on line manual ly .
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Output Examples The follo wing example sho ws the output wh en f ield diag nostics are performed on the line card in slot 7.
5-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command 5d20h: %GRP-4-RSTSLOT: Re.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 FDIAG_STAT_IN_PROGRESS(.
5-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command FD 3> GSR Field Diagnostics V6.01 FD 3> Compiled by award on Tue Apr 9 07:22:53 PDT 2002 FD 3> view: award-conn_isp.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The follo wing example sho ws the output of a line card test with the update-fpga option specif ied.
5-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Command COMPLETED Field Diags: pi.
Chapter 5 Field Diagnostics for the Cisco 12000 Series Router Using the diag Comm and 5-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
CH A P T E R 6-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 6 Maintaining the Router The Cisco 12006 or Cisco 12406 Router is equ ipped as ordered and is ready to install and start up when it lea ves the factory .
Chapter 6 M aintaining the Router Powering Down th e Router 6-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 • Removing and Installing a Clock an d Sc hedule.
6-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Front Door on Ci sco 12006 and Cisco 12406 Enhanced Series Router Step 4 V erify that the follo wing conditions are true: a.
Chapter 6 M aintaining the Router Removing and Installing the Front Door on Cisco 12006 a nd Cisco 12406 Enhanced Series Router 6-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 1 Open the front door b y pressing the righ t latch button ( Fi gure 6-1 ).
6-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Front Door on Ci sco 12006 and Cisco 12406 Enhanced Series Router Step 2 Remov e the front door b y lifting the ( top and bottom) hinge pins to free the door from the chassis ( Fig ure 6-2 ).
Chapter 6 M aintaining the Router Removing and Installing the Front Door on Cisco 12006 a nd Cisco 12406 Enhanced Series Router 6-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 4 Remov e the bu mpers and piv o t blocks from the door as shown in Fi gure 6-3 .
6-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Cleaning or Replacing the Air Filters Step 6 Attach the front door to the chassis: a. Remov e the hinge pins from the hi nges on the right side of the chassis.
Chapter 6 M aintaining the Router Cleaning or Replacing the Air Filters 6-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Use the following procedure to clean or replace the air filters.
6-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing an d Replacing the Blower Modu le Step 2 V isually check the c ondition of the air f ilters to determin e whether to clean them or install new replacements.
Chapter 6 M aintaining the Router Removing and Replacing the Blower Modu le 6-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Use the follo wing procedure to remo ve and replace the blo wer module. Step 1 Remov e the blo wer module from the chassis ( Figure 6-5 ): a.
6-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing an d Replacing the Blower Modu le Step 2 Install the ne w blo wer module ( Figure 6-6 ): a.
Chapter 6 M aintaining the Router Removing and Replacing the Blower Modu le 6-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 6-6 Installing the Bl owe.
6-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing AC and DC Power Subsystem Components Step 3 Check the .
Chapter 6 M aintaining the Router Removing and Replac ing AC and DC Power Subs ystem Components 6-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 The follo win.
6-15 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing AC and DC Power Subsystem Components Caution Ne wer , 1900 W DC po wer supplies require the upgr aded PDU.
Chapter 6 M aintaining the Router Removing and Replac ing AC and DC Power Subs ystem Components 6-16 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 DC Power Supply (PWR-GSR6-DC=) Used to replace 1400 W po wer supplies only .
6-17 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing AC and DC Power Subsystem Components Installing Upgrade Kits When installing a po wer system upgrade kit, repl ace the follo wing components.
Chapter 6 M aintaining the Router Removing and Replacing an AC PEM 6-18 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Removing and Replacing an AC PEM This section contains the procedure to remov e and replace an AC PEM from the chassis.
6-19 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PEM Use the follo wing procedure to remo ve and replace an A C power supply . Caution Y ou cannot mix po wer supply types within the chassis.
Chapter 6 M aintaining the Router Removing and Replacing an AC PEM 6-20 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 4 Remov e the PEM from the chassis ( Figur e 6-8 ): a. Loosen the captiv e screw on each ejector le ver .
6-21 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PEM Step 5 Install the ne w pow er supply ( Figure 6-9 ): a. Slide the po wer supply into the bay until it mates with its backplane connector .
Chapter 6 M aintaining the Router Removing and Replacing an AC PEM 6-22 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 6 Plug the power supply ca ble into its AC outlet. Step 7 Po wer on the circuit breake r to that A C outlet.
6-23 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PEM Step 3 Check the po wer supply status indica.
Chapter 6 M aintaining the Router Removing and Replacing an AC PDU 6-24 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Removing and Replacing an AC PDU Use the following procedure to re mov e and replace an A C PDU.
6-25 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PDU Caution The system must be powered of f to re mov e and replace the PDU .
Chapter 6 M aintaining the Router Removing and Replacing an AC PDU 6-26 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Figur e 6-1 1 Unseating the AC P ower Supp.
6-27 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PDU Step 5 Release the retention clip and disconnec t each po wer supply cord from the PDU (see Figure 6-10 ).
Chapter 6 M aintaining the Router Removing and Replacing an AC PDU 6-28 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 7 Remov e the PDU fr om the chassis ( Figure 6-13 ): a. Loosen the (4 ) capti ve scre ws on the PDU.
6-29 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing an AC PDU Step 9 Install the blo wer module ( Figure 6-14 ): a. Position the alig nment holes on the blo wer module with the guide pins on the chassis and PDU.
Chapter 6 M aintaining the Router Removing and Replacing an AC PDU 6-30 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 13 Reinstall the po wer supplies ( Figure 6-15 ): a. Push the po wer supply i nto its bay until it mat es with its PDU connector .
6-31 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PEM The A C Input Po wer and DC Output Po wer indicators on the po wer supplies should light.
Chapter 6 M aintaining the Router Removing and Replacing a DC PEM 6-32 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Use the follo wing procedure to remo ve and replace a DC po wer supply . Caution Y ou cannot mix po wer supply types within the chassis.
6-33 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PEM Step 3 Remov e the po wer supply from the chassis ( Figure 6-1 7 ): a. Loosen the captiv e screw on each ejector le ver .
Chapter 6 M aintaining the Router Removing and Replacing a DC PEM 6-34 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 4 Install the ne w pow er supply: a. Slide the po wer supply into the bay until it mates with its backplane connector .
6-35 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PEM Step 5 Po wer on the circuit breake r . Step 6 Set the po wer switch to the On position. The A C Input and DC Outpu t power ind icators on the front of the po wer supply should light.
Chapter 6 M aintaining the Router Removing and Replacing a DC PEM 6-36 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 3 Check the po wer supply status indic.
6-37 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PDU Removing and Replacing a DC PDU Use the following procedure to remo ve and replace a DC PDU. be for e beginning this procedure, read the “Installation Gu idelines” section on page 6-14 .
Chapter 6 M aintaining the Router Removing and Replacing a DC PDU 6-38 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Caution The system must be powered of f to re mov e and replace the PDU .
6-39 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PDU Step 3 Loosen the captiv e screw on each ejector le v er and pi vot the lev ers open to unse at the po wer supply from its PDU connector ( Figure 6-20 ).
Chapter 6 M aintaining the Router Removing and Replacing a DC PDU 6-40 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 4 Remov e the blo wer module ( Figure 6-21 ): a. Lift the blo wer module handle to it s raised (carrying) position.
6-41 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PDU Step 5 Disconnect the DC po wer leads from the PDU po wer connector bl ocks in the follo wing order ( Figure 6-22 ): a.
Chapter 6 M aintaining the Router Removing and Replacing a DC PDU 6-42 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 6 Remov e the PDU fr om the chassis ( Figure 6-23 ): a. Loosen the (4 ) capti ve scre ws on the PDU.
6-43 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PDU Step 8 Install the blo wer module ( Figure 6-24 ): a. Position the alig nment holes on the blo wer module with the guide pins on the chassis and PDU.
Chapter 6 M aintaining the Router Removing and Replacing a DC PDU 6-44 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 9 Reconnect the DC power leads to the PDU power connector blocks in th e follo wing order ( Figure 6-25 ): a.
6-45 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Replacing a DC PDU Step 11 Reinstall the po wer supplies: a. Push the po wer supply i nto its bay until it mat es with its PDU connector .
Chapter 6 M aintaining the Router Removing and Replacing a DC PDU 6-46 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 12 Power on the power supplies. The Output Po wer OK and Input Po wer OK indicators on the po wer supplies should light.
6-47 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing an RP or a Line Card Removing and Installing an RP or a Line Card Line cards can occupy any slot, slot 0 (the top slot) thro ugh slot 4, in the RP and line card cage.
Chapter 6 M aintaining the Router Removing and Insta lling an RP or a Line Card 6-48 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Tools and Equipment T o remo .
6-49 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing an RP or a Line Card Figur e 6-28 Removing an RP or L.
Chapter 6 M aintaining the Router Removing and Insta lling an RP or a Line Card 6-50 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Step 8 Immediately place the .
6-51 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing an RP or a Line Card Step 6 Grasp the edges of the metal card carri er with both hands to support and guide the RP or line card into the slot alignment groov es in the card cage.
Chapter 6 M aintaining the Router Removing and Insta lling an RP or a Line Card 6-52 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Caution Handle line cards by the metal card carrie r edges only; avoid touching the board itself or an y connector pins.
6-53 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing an RP or a Line Card The Cisco 12000 Series Router li.
Chapter 6 M aintaining the Router Removing and Insta lling an RP or a Line Card 6-54 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Reconnecting Cables to a Line.
6-55 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing an RP or a Line Card Step 2 Attach an appropriate number of velcro straps t o support the networ k interface cables, through the slots in the cable-management bracket: a.
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-56 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guid.
6-57 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Al.
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-58 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guid.
6-59 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Al.
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-60 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guid.
6-61 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Al.
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-62 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guid.
6-63 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Alarm Card Step 6 Slide the card out of t he slot and place it directly into an antistatic bag or other ESD-pre venti ve co ntainer .
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-64 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Caution SFC ejector lev ers may not fit flush agains t th e SFC facepl ate.
6-65 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Alarm Card Removing and Installing an Alarm Card The two alarm cards occupy the card slots in the alar m card bay .
Chapter 6 M aintaining the Router Removing and Insta lling a Clock and Schedule r Card, Switch Fabric Car d, or Alarm Card 6-66 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guid.
6-67 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing a Clock and Scheduler Card, Switch Fabric Card, or Alarm Card Caution Alarm card capti ve scre ws must be tightened to ensure EMC compliance.
Chapter 6 M aintaining the Router Removing and Installing the Chassis 6-68 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Removing and Installing the Chassis Ins.
6-69 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Chassis Before You Begin Y ou will need to remov e all the components e xcept the air filter from the defective chassis and reinstall them in the replace ment chassis.
Chapter 6 M aintaining the Router Removing and Installing the Chassis 6-70 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Preparing the Defective Chassis T o pre.
6-71 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Chassis Disconnecting Line Card Interface Cables Disconnect the line card network interface cab les from each line card as instructed in the “Removing an RP or Line Card” section on page 6-48 .
Chapter 6 M aintaining the Router Removing and Installing the Chassis 6-72 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Transferring RP and Line Cards Y ou must remove the l ine cards and RP(s) from the line card and RP card cage, then install them in the card cage in the replacement chassis.
6-73 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Chassis Remove each CSC from its slot in the de fectiv e chassis as instructed in the “Removing a Cloc k and Scheduler Card ” section on pa ge 6-58 .
Chapter 6 M aintaining the Router Removing and Installing the Chassis 6-74 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Detaching the Supplemental Bonding and .
6-75 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Removing and Installing the Chassis • Mounted directly agai nst the rack fl.
Chapter 6 M aintaining the Router Removing and Installing the Chassis 6-76 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 Installing the Chassis in the Equipment.
6-77 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Chapter 6 Maintaining the Router Upgrading the RP and Line Card Memory Reconnecting Line Card Netw ork Interface Cables Reconnect line card network interface cabl es as described in the “Connecting RP and Line Card Cables” section on page 3-11 .
Chapter 6 M aintaining the Router Upgrading the RP and Line Card Memory 6-78 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
A-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 APPENDIX A Technical Specifications This appendix pro vides information and techni cal specifications fo r the Cisco 12006 and Cisco 12406 Routers.
Appendix A Technical Sp ecifications Specifications A-2 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Ta b l e A -1 Ph ysical Specifications Description Va l u e Chassis hei ght 18.5 in (46.9 cm) Chassis width 17.
A-3 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Appendix A Technical Sp ecifications Specifications The electrical specifications and values listed in T able A-2 are for a system equipped with t he A C-input po wer distribut ion unit (PDU) and A C-input po wer supply modu les.
Appendix A Technical Sp ecifications Specifications A-4 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Caution T o ensure that the chassis configurati on complies with the requir ed power budgets, use the on-line po wer calculator .
A-5 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Appendix A Technical Sp ecifications Specifications Caution Exhaust from other equipment vented directly into the Ci sco 12006 and Cisco 12406 Router air inlet may cause ov erheati ng.
Appendix A Technical Sp ecifications Specifications A-6 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Alarm Card Alarm Relay Connector Specifications The alarm card alarm relay connector is a standard DB-9 connector .
A-7 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03 Appendix A Technical Sp ecifications Specifications On Cisco 12000 Series Routers that support switching capaci.
Appendix A Technical Sp ecifications Specifications A-8 Cisco 12006 and Cisco 12406 Router Inst allation and Configuration Guide OL-11497-03.
IN-1 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 INDEX Numerics 100BASE-T Ethernet port GRP 1-24, 3-22 maximum cable lengths 3-29 PRP 1-32 specifications 3-29 .
Index IN-2 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 See also console port, auxiliary port auxiliary port description 1-24, 1-32 pinout (table) GRP 3-17 PRP.
IN-3 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index Flash memory card insertion 3-67 formatting Flash me mory card erases data 3-82 GRP soft reset (NMI) swi.
Index IN-4 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 configuration file, saving 3-64 interfaces 3-58, 3-61 register bit meanings 4-8, 4-11 boot field 4-8 ch.
IN-5 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index D DC-input PEM description 1-46 electrical codes 2-4 input current rati ng A-4 input power rating A-4 LE.
Index IN-6 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 description GRP 1-24, 3-22 PRP 1-32 interface configuration 3-59 EXEC command interpreter 3-51 F Fast E.
IN-7 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index description 1-24 Cisco IOS software images 1-17, 1-19 console port connections (figure) 3-15 description.
Index IN-8 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 troubleshooting AC-input power subsystem 4-23 DC-input power subsystem 4-26 lightning st orm, safety du.
IN-9 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index online insertion and remo val See OIR P passwords, re covering 4-14 PCMCIA description, slot 1-23 format.
Index IN-10 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 auxiliary port connections (figure) 3-18 description 1-32 pinout (table) 3-20 Cisco IOS software image.
IN-11 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index SELV circuit connections 3-19 saving the configu ration file 3-64 SDRAM PRP attribute summary (table) 1.
Index IN-12 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03 See switch fabric circuitry switch fabric circuitry identificat ion labels 1-12, A-7 overview 1-10 to .
IN-13 Cisco 12006 and Cisco 12406 Router I nstallation and Configuration Guide OL-11497-03 Index DC-input PEM A-4 W warnings circuit breaker s witch, DC-input PEM 3-32 connecting to SELV circuits 3-25.
Index IN-14 Cisco 12006 and Cisco 12406 Router Inst all ation and Configuration Guide OL-11497-03.
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems Cisco 12406 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems Cisco 12406 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems Cisco 12406 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems Cisco 12406 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems Cisco 12406 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems Cisco 12406 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems Cisco 12406 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems Cisco 12406. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems Cisco 12406 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
