Benutzeranleitung / Produktwartung ASR1002 des Produzenten Cisco Systems
Zur Seite of 36
Q UICK S TART G UIDE Cisco ASR 1002 Router 1 Documentation and R esources 2 Prepare for Installation 3 Rac k-Mount the Router 4 Connect the Rou ter to the Network 5 Star t the System 6 Configuring the.
2 1 Documentation and Resources Documentation for the Cisco 1000 Series Ag gregation Services Routers documen tation is online with the exception of the regulatory compliance a nd sa fety documentation and the Cisco 1000 Se ries Aggregation Servic es Routers documentation flyer .
3 2 Prepare for Installation This section contains information about tools and parts, wa rnings, site preparation information, and information for rack-mount and equipment shelf or tabletop in stallation. War n in g Only trained and qualified p ersonnel should instal l, replace, or service this equipment.
4 Prepare for Rack-Mount Installation Before you begin the rack-mounting tasks: • Decide whether or not you want to front-mount or rear -mount the chassis.
5 Attach the Rack-Mount Bracke ts—Chassis Rear-Mounted T o install the rack-mount on a Cisco ASR 1002 Router fo r a rear rack-mount configuration, follow these steps: Step 1 Locate the threaded ear holes in the rear sides of the chassis. Step 2 Position the rear rack-mount bracket t op hole with the chassis from the back (See Figure 2 ).
6 Figure 3 shows the Cisco ASR 1 002 Router in a four -post rack. Figur e 3 Installing the Cisco A SR 1 0 02 Router in a F our -Post Rac k - Fr ont and Rear Rack-Mounting Note Because the rack-mount brack ets support the weight of the entire chassis, be sure to use all screws to fasten the two rack-mount brackets on the chassis to the rack posts.
7 Ti p T o allow spac e to attach the cable-management brackets to the c hassis in the rack easily , make certain that you use th e rack-mount bracket ear holes specified in Step 9. Step 8 Hold the chassis in position against th e mounting rails and follow these steps: a.
8 Caution If you are using a two-post rack, secure the rack to the floor surface to prevent tipping and avoid bodily injury and component damage. Step 1 Pos ition the chassis so the front is clos est to you and lift it carefully into the rack. T o prevent injury , avoid any sudden twists or moves.
9 Figure 5 Attac hing the Cabl e-Management Brack et to the Cisco ASR 1 0 02 Router Step 3 Using the bottom rack-mount ear hole, insert the screw th rough cable-management bracket and into the chassis rack-mount bracket. Figure 5 shows the cable-management brac kets attached to the chassis.
10 Figur e 6 Cisco A SR 1 002 Router Gr ound Connect or Locati on and eUSB P anel Door Step 1 Use the wire stripper to strip one end of the A W G #6 wire approximately 0.75 inches (19.05 mm). Step 2 Insert the A WG #6 wire into the wi re receptacle on the grounding lug.
11 Step 5 Locate the chassis gro und connector on the side of your c hassis. Step 6 Insert the two screws through the holes in the groundi ng lug. Step 7 Use the Number 2 Phillips screwdriver to carefully ti ghten th e screws until the grounding lug is held firmly to the chassis.
12 Figur e 8 Cisco ASR 1 0 02 Integr at ed Rout e Processor Console and A uxiliary Por t Connectors Step 3 After you establish normal router operat ion, you can disconnect th e terminal.
13 Step 3 Configure to a fixed speed through th e command-line interface (CLI) commands. Connect the Shared Port Adapter Cables The instructions for connecting the cables for the shared port adapters .
14 Proceed to the “Start the System” section on page 14 to complete the installation . 5 Start the System Before you start the system, yo u must connect power to it. Connect AC Power to t he Cisco ASR 1002 Router This section provides instructions for installing the AC power su pply into the Cisco A SR 1002 Router .
15 Figur e 1 1 AC P ow er Supply for the Cisco A SR 1 002 Router Table 1 describes the AC power suppl y LEDs on the Cisco ASR 1002 Router . T able 1 Cisco ASR 1 0 02 Router AC P ower Supply LEDs Note T o connect an AC power sup ply to the Cisco ASR 1002 Router , follow the steps in Installing the AC Power Supply, page 31 .
16 Figure 12 shows the DC power supply for the Cisco ASR 1002 Router . Figur e 12 DC P o wer Su pply fo r the Cisco A SR 1 0 02 Router Table 2 describes the DC power suppl y LEDs on the Cisco ASR 1002 Router .
17 Note The color coding of the DC-input power supply leads depends on the color coding of the DC power source at your site. T ypically , green or green/yellow is used for ground. Make ce rtain the lead color co ding you choose for the DC-input power supply matches lead colo r codi ng used at the DC power source.
18 Step 9 Connect the ground, positive, and ne gative leads to the power source. Step 10 T urn the branch source breake r on. Step 11 T urn the power supply sw itch to the On (I) position. Step 12 V erify that the LED s illuminate. This completes the procedure fo r connecting DC-input power .
19 Step 1 T urn on power . The green OK LED on the power supply tu rns on. (Both power supplies are required in the Cisco ASR 1002 Router .) Step 2 Listen for the fans; you should immediately hear th em operating. Step 3 During the boot process, observe the system LEDs.
20 Table 4 pro vides information about the Cisco ASR1 000-ESP5 LED s in the Cisco ASR 1002 Router as the system starts. T able 4 Cisco ASR1 0 00-ESP5 and ASR1 0 00-ESP1 0 LED Activity During the boot process, observe the syst em LEDs. The ST A TUS LED comes on immediatel y as amber , then turns to green when the Cisco IOS is booted.
21 %IOSXEBOOT-4-DEBUG_CONF: (rp/0): Using DEBUG_CONF file /misc/scratch/debug.conf Feb 13 13:00:38.546 R0/0: %PMAN-3-PROCFAIL_IGNORE: All process failures are being ignored due to debug settings.
22 *Feb 13 13:01:28.701: %LINK-5-CHANGED: Interface GigabitEthernet0, changed state to administratively down *Feb 13 13:01:29.728: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Feb 13 13:01:14.738: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of 5) ready.
23 Router> enable Step 3 At the password prompt, enter your system password. If an en able password has not been se t on your system, this step may be skipped.
24 for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: n First, would you like to see the curr.
25 no ip address ! interface GigabitEthernet0/0/1 shutdown no ip address ! interface GigabitEthernet0/0/2 shutdown no ip address ! interface GigabitEthernet0/0/3 shutdown no ip address ! interface Gig.
26 Enter your selection [2]: Router#reload Proceed with reload? [confirm] *Jan 11 06:59:29.476: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload command. System Bootstrap, Version 12.2(20071105:235056) [gschnorr-mcp_rommon_rel_1_25 101], DEVELOPMENT SOFTWARE Copyright (c) 1994-2007 by cisco Systems, Inc.
27 Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec.
28 Save the Running Conf iguration to NVRAM T o store the configuration or changes to your startup configur ation in NVRAM, use the copy run ning-config startup-config command to save your configura tion changes to the startup config uration so that the changes will not be lost if the software reloads or a powe r outage occu rs.
29 Power Off the Cisco ASR 1002 Router This section explains how to shut down the Cisco ASR 1002 Router . It is recommended that before turning off all power to the chassis, you issue the reload command. This insures that the operating system cleans up all the file systems.
30 Step 2 Using the handles on both sides of the module, with two ha nds, gently insert the Cisco ESP5 or -ESP10 into the top chassis slot. Note Handle the Cisco ESP5 and ESP10 by the carrier edges only ; never touch the printed circuit board components or connector pins.
31 Step 9 Power on the router by turning the power switch to the on (I) position. Replace a Power Supply in the Cisco ASR 1002 Router This section provides instructions for removing and replaci ng the AC power supply and the DC power supply in a Cisco ASR 1002 Router .
32 Figur e 14 Cisco ASR 1 0 02 Router A C P ower Cord b. T ake the power cord and run it below the handles of the pow er supply in slot 1 (the power supply you are connecting) and the power supply in slot 0 (left) as shown in Figure 15 . Make sure the power cord is hanging loosely so that it cannot be disconnected from the AC power inlet.
33 Note Using a tie wrap for the AC pow er cable is optional and n o t necessary . However , if you do attach the AC power cable to a power supply tab and th en you remo ve the AC power cable for some reason, check for any damage to the cable after you cut the tie wrap off.
34 Step 7 Replace the DC power supply within five minutes o r the system will shutdown. Y ou have completed the procedure for removing a DC pow er supply from the Cisco ASR 1002 Ro uter . Installing the DC Power Supply This section provides information about replacing a DC power suppl y in the Cisco ASR 1002 Router .
35 Figur e 18 Cisco ASR 1 0 02 Ro uter DC Po wer Supply Step 5 Insert the stripped end of the ground lead all the w ay into th e ground lead receptacle on the DC-input power supply , and tighten the receptacle screw usi ng a 3.5 mm fla t-blade screwdriver to a torque of 0.
Americas Headquarters Cisco Systems, Inc. 170 W est T asman Drive San Jose, CA 95134-1706 USA www .cisco.com T el: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Asia Pacific Headquarters Cisco Systems, Inc. 168 Robinson Road #28-01 Capital T ower Singapore 068912 www .
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems ASR1002 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems ASR1002 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems ASR1002 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems ASR1002 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems ASR1002 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems ASR1002 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems ASR1002 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems ASR1002. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems ASR1002 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
