Benutzeranleitung / Produktwartung 78-6897-01 des Produzenten Cisco Systems
Zur Seite of 87
Feedback on the ATM Switch Router Quick Software Configuration Guide 78-6897-01 Thank you for taking the time to fill out this response card. Your input is important to us and helps us to provide you with better documentation. If you have comments about this document, please complete this self-addressed response card and mail it to us.
.
170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Cisco Systems, Inc. Corporate Headquarters Tel: 800 553-NETS (6387) Fax: 408 526-4000 408 526-4100 ATM Switch Router Quick Softwa.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED.
EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, R egistrar, Strat aV iew Plus, Stratm, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. in the U.S. and certain other countries.
Contents v CONTENTS About This Guid e ix Purpos e ix Audienc e ix Organizatio nx Related Documentatio nx Convention s xi Cisco Connection Onlin e xii Documentation CD-RO M xiii Chapter 1 Using the Com.
ATMSwitch Router Quick Software Configuration Guide vi Chapter 3 Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnel s 3-1 Configuring SVC s 3-1 Configuring the Route r 3-2 C onfiguring Signaling on .
Contents vii LANE Configuration Example s 4-9 Verifying Connectivit y 4-15 Confirming Connectivity between the ATM Switch Router and the Router s 4-16 Displaying the LANE Client Configuration on the A.
ATMSwitch Router Quick Software Configuration Guide viii.
About This Guide ix About This Guide This preface describes the purpose, audience, organization, and conventions of this AT M Switch Router Quick Software Configuration Guide, and provides information on how to obtain related documentation. Purpose This guide is intended as a starting place for configuring the ATM switch router.
Organization ATMSwitch Router Quick Software Configuration Guide x Organization This guide is organized as follows: Related Documentation This guide is part of the ATM switch router software documenta.
About This Guide xi Conventions Conventions This document uses the following conventions: Notes use the following conventions: Note Means reader take note . Notes contain helpful suggestions or references to material not covered in the publication. Convention Description boldface font Commands and keywords are in boldface .
Cisco Connection Online ATMSwitch Router Quick Software Configuration Guide xii Timesavers use the following conventions: Timesaver Means the described action saves time . You can save time by performing the action described in the paragraph. Tips use the following conventions: Tips Means the following are useful tips.
About This Guide xiii Documentation CD-ROM You can access CCO in the following ways: • WWW : http://www.cisco.com • WWW : http://www-europe.cisco.com • WWW : http://www-china.cisco.com • Telnet : cco.cisco.com • Modem : From North America, 408526-8070; from Europe, 33164464082.
Documentation CD-ROM ATMSwitch Router Quick Software Configuration Guide xiv.
CHAPTER Using the Command-Line Interface 1-1 1 Using the Command-Line Interface This chapter describes what you need to know about the Cisco IOS software (the software that runs the ATM switch router).
Getting Help ATMSwitch Router Quick Software Configuration Guide 1-2 Getting Help You can use the question mark (?) and arrow keys to help you enter commands.
Using the Command-Line Interface 1-3 Understanding Interface Numberin g Tips If you are having difficulty entering a command, check the prompt and then enter the question mark (?) for a list of available commands. You might be in the wrong command mode or using the wrong syntax.
Understanding Interface Numberin g ATMSwitch Router Quick Software Configuration Guide 1-4 Card Numbering Card numbering starts at 0 and increments by 1 from top to bottom, as shown in Figure1-1. The card number slots are silkscreened on the left side of each slot.
Using the Command-Line Interface 1-5 Subcard Numbering Subcard Numbering Subcards are numbered from 0 to 1, left to right. Subcards include half-width port adapters and full-width interface modules (such as an OC-12 interface module). Two half-width port adapters can occupy one chassis slot.
Understanding Interface Numberin g ATMSwitch Router Quick Software Configuration Guide 1-6 Processor Card Numbering The CPU interface on the processor card is addressed as either ethernet 0 or atm 0 , depending on the type of configuration. The other interfaces on the processor card start with 0 and increment by 1.
Using the Command-Line Interface 1-7 Example of Interface Numbering Example of Interface Numbering Figure1-5 shows a Catalyst8540MSR chassis populated with several half-width port adapters and full-width interface modules. In this example, 12/0/3 is called out in the last interface module installed in the chassis.
Undoing a Command or Feature ATMSwitch Router Quick Software Configuration Guide 1-8 Undoing a Command or Feature If you want to undo a command you entered or disable a feature, you can enter the keyword no before most commands; for example, no atm router pnni .
Using the Command-Line Interface 1-9 Saving Configuration Changes To see a complete list of available more commands, enter the more ? command: Switch# more ? access-lists List access lists accounting .
Where to Go Next ATMSwitch Router Quick Software Configuration Guide 1-10 Where to Go Next Now that you have learned some CiscoIOS software basics, you can begin to configure the ATM switch router. Remember that: • You can use the question mark (?) and arrow keys to help you enter commands.
CHAPTER Getting Started 2-1 2 Getting Started This chapter describes basic software configuration of the ATM switch router, and includes the following sections: • Naming the ATM Switch Router • As.
Naming the ATM Switch Router ATMSwitch Router Quick Software Configuration Guide 2-2 Take these steps: Example Switch> enable Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# hostname Nevada_Switch Nevada_Switch(config)# Verify Switch# more system:running-config ! version xx.
Getting Started 2-3 Assigning a Password Assigning a Password Configure an administrative password on the ATM switch router to prevent unauthorized configuration changes.
Setting Up Remote Administrative Access ATMSwitch Router Quick Software Configuration Guide 2-4 Setting Up Remote Administrative Access You can configure the Ethernet interface on the processor card (CPU card) so that you can Telnet to the ATM switch router and configure it remotely.
Getting Started 2-5 Setting Up Remote Administrative Access Example Switch> enable Switch# configure terminal Switch(config)# ip route 172.20.52.0 255.255.255.0 ethernet 0 Switch(config)# interface ethernet 0 Switch(config-if)# ip address 172.20.52.
Setting Up Remote Administrative Access ATMSwitch Router Quick Software Configuration Guide 2-6.
CHAPTER Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-1 3 Configuring SVCs, PVCs, Sof t PVCs, PVPs, and V P Tunnels This chapter describes how to configure switched virtual circuits (SVCs), .
Configuring SVCs ATM Switch Router Quick Software Configuration Guide 3-2 If the SVC terminates on a router, ho wever, configuration is required on the r outer w here the SVC terminates. For your convenience, t he router configuration is d escribed in this section.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-3 Configuring the Router C onfiguring Signaling on t he R oute rs Configure PVCs for QSAAL and ILMI signaling on the main ATM interfaces of both the source and destination routers that terminate the SVC.
Configuring SVCs ATM Switch Router Quick Software Configuration Guide 3-4 Example Router> enable Router# configure terminal Enter configuration commands, one per line.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-5 Configuring the Router Example Router> enable Router# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)# interface atm 0.1 multipoint Router(config-subif)# ip address 193.
Configuring SVCs ATM Switch Router Quick Software Configuration Guide 3-6 Determining the NSAP Address Determine the ATM network service access point (NSAP) address for both the source and destination routers. The NSAP addresses is required to complete the SVC.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-7 Configuring the Router Example Switch# show interface atm 0.1 ATM0.1 is up, line protocol is up Hardware is ATMizer BX-50 Internet address is 192.153.185.65/27 MTU 4470 bytes, BW 155520 Kbit, DLY 100 usec, rely 255/255, load 1/255 NSAP address: 47.
Configuring SVCs ATM Switch Router Quick Software Configuration Guide 3-8 Exampl e Router> enable Router# configure terminal Router(config)# interface atm 0.1 multipoint R outer(config- subif) # map-group hawaii Router(config- subif) # no shutdown Router(config-subif)# exit Router(config)# map-list hawaii Router(config-map-list)# ip 192.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-9 Configuring PVCs Configuring PVCs A PVC is a permanent logical connection that you must configure manually, from source to destination, through the ATM network. Once configured, the ATM network maintains the connection at all times, regardless of traffic flow.
Configuring PVCs ATM Switch Router Quick Software Configuration Guide 3-10 Table3-2 describes the in and out interfaces and associated VPIs/VCIs for the PVC shown in Figur e 3-2 .
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-11 Configuring the ATM Switch Router Note If the PVC terminates on an A TM switch router, you must terminate the connection on the route processor interface ATM 0 .
Configuring PVCs ATM Switch Router Quick Software Configuration Guide 3-12 Configuring the Router If the PVC terminates on a router, you must configure a PVC from the router to the ATM switch router. Take these steps: Step Command Purpose 1 Router> enable Router# Enter privileged EXEC mode.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-13 Configuring Soft PVCs Example Router> enable Router# configure terminal Router(config)# interface atm 0.
Configuring Soft PVCs ATM Switch Router Quick Software Configuration Guide 3-14 Figure3-3 illustrates how to set up soft PVCs. This example network is used throughout this section.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-15 Configuring the ATM Switch Router Determining t he Destination ATM Switch Router NSAP Address Determine the destination ATM switch router NSAP address for the interface. See the ATM switch router C in Figure3-3.
Configuring Soft PVCs ATM Switch Router Quick Software Configuration Guide 3-16 Verify Not applicable. Configuring the Source ATM Switch Router Most of the configuration for the soft PVC occurs on the source switch. See the ATM switch router B in Figure3-3.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-17 Configuring the Router Verify The following example displays the soft VC configuration of sw itch B, on interface 3/0/1 out to the ATM networ.
Configuring Soft PVCs ATM Switch Router Quick Software Configuration Guide 3-18 Example Router> enable Router# configure terminal Router(config)# interface atm 0.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-19 Configuring PVPs Configuring PVPs A VP connection is like a bundle of VCs, transporting all cells with a common VPI, rather than a specific VPI and VCI. A PVP is a provisioned VP (like a PVC).
Configuring PVPs ATM Switch Router Quick Software Configuration Guide 3-20 Take these steps: Example The following example shows how to configure the internal cross c onnect (within the switch) PVP on.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-21 Configuring VP Tunnels Configuring VP Tunnels A VP tunnel is a method of linking two private ATM networks across a public network that does not support SVCs. The VP tunnel provides a permanent path through the public network.
Configuring VP Tunnels ATM Switch Router Quick Software Configuration Guide 3-22 Take these steps: Example The following example shows how to configure the VP tunnel on VPI=99. Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z.
Configuring SVCs, PVCs, SoftPVCs, PVPs, and VPTunnels 3-23 Configuring VP Tunnels Verify When the VP tunnel is configured on both ends and the connection is up, the AutoCfgState displays “completed.” Switch# show atm interface atm 3/0/2.99 Interface: ATM3/0/2.
Configuring VP Tunnels ATM Switch Router Quick Software Configuration Guide 3-24.
CHAPTER Configuring LANE 4-1 4 Configuring LANE This chapter describes how to configure LAN Emulation (LANE) on the ATM switch router, and includes the following sections: • Understanding LANE on AT.
Understanding LANE on ATM ATMSwitch Router Quick Software Configuration Guide 4-2 Understanding LANE on ATM LANE is a protocol that allows devices attached to traditional LANs (such as Ethernet and Token Ring) to connect to ATM networks.
Configuring LANE 4-3 Implementing LANE • LANE server (LES)—A server that registers LECs to join the ELAN. In LANE 1.0, without Simple Server Redundancy Protocol (SSRP), each ELAN has only one Cisco LES, which handles LAN Emulation Address Resolution Protocol (LE_ARP) requests.
Implementing LANE ATMSwitch Router Quick Software Configuration Guide 4-4 Assigning Components to Interfaces and Subinterfaces The following rules apply to assigning LANE components to the major ATM interface and its subinterfaces: • The LECS always runs on the major ATM interface.
Configuring LANE 4-5 Configuring a LEC Configuring a LEC This section describes how to configure a LANE client connection from a remote ATM switch router to the processor card (CPU) of a local switch. This connection allows you to configure the ATM switch router remotely.
Configuring the LECS ATMSwitch Router Quick Software Configuration Guide 4-6 Configuring the LECS This section describes how to configure the LECS, and includes the following procedures: • Configuring the ATM Address of the LECS • Configuring the LECS Database You must configure the ATM address of the LECS on the ATM switch router.
Configuring LANE 4-7 Configuring the LECS Database For examples of these commands, see the section “LANE Configuration Examples” at the end of this chapter. Configuring the LECS Database Take these steps: 6 Switch(config)# atm address address Configure a new ATM address.
Configuring the LES/BUS ATMSwitch Router Quick Software Configuration Guide 4-8 For examples of these commands, see the section “LANE Configuration Examples” at the end of this chapter. Configuring the LES/BUS In Cisco’s implementation of LANE, the LES and BUS are treated as one LANE component.
Configuring LANE 4-9 LANE Configuration Examples LANE Configuration Examples The following examples show how to configure one Cisco 7505 router, one ATM switch router, and one Catalyst 5500 switch for a single ELAN. The ATM switch router contains the LECS, LES, BUS, and a LEC.
LANE Configuration Examples ATMSwitch Router Quick Software Configuration Guide 4-10 ATM Switch Router ATM_Switch# show lane default-atm-addresses interface ATM0: LANE Client: 47.00918100000000E04FACB401.00E04FACB402.** LANE Server: 47.00918100000000E04FACB401.
Configuring LANE 4-11 LANE Configuration Examples ATM_Switch# show lane config LE Config Server ATM0 config table: eng_dbase Admin: up State: operational LECS Mastership State: active master list of global LECS addresses (42 seconds to update): 47.00918100000000E04FACB401.
LANE Configuration Examples ATMSwitch Router Quick Software Configuration Guide 4-12 ATM_Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. ATM_Switch(config)# interface atm 0.1 ATM_Switch(config-subif)# lane client ethernet eng_elan ATM_Switch(config-subif)# end ATM_Switch# show lane client LE Client ATM0.
Configuring LANE 4-13 LANE Configuration Examples Current configuration: ! version 12.0 <Information deleted> ! interface ATM3/0 no ip address atm pvc 1 0 5 qsaal atm pvc 2 0 16 ilmi ! interface ATM3/0.1 multipoint lane client ethernet eng_elan ! <Information deleted> ! end router1# show inter atm 3/0.
LANE Configuration Examples ATMSwitch Router Quick Software Configuration Guide 4-14 ATM# configure terminal Enter configuration commands, one per line.
Configuring LANE 4-15 Verifying Connectivity Verifying Connectivity The following example shows how to use the show lane and ping commands to confirm the connection between the ATM switch router, rout.
LANE Configuration Examples ATMSwitch Router Quick Software Configuration Guide 4-16 LE Client ATM0.1 ELAN name: eng_elan Admin: up State: operational Client ID: 1 LEC up for 1 hour 34 minutes 46 seconds ELAN ID: 0 Join Attempt: 1 HW Address: 00e0.4fac.
Configuring LANE 4-17 Verifying Connectivity Success rate is 100 percent (5/5), round-trip min/avg/max = 1/202/1000 ms ATM_Switch# ping 172.16.0.3 Type escape sequence to abort.
LANE Configuration Examples ATMSwitch Router Quick Software Configuration Guide 4-18.
CHAPTER Configuring Tag Switching 5-1 5 Configuring Tag Switching This chapter describes how to configure tag switching, and includes the following sections: • Software Restrictions • Configuring .
Configuring Tag Switching on an ATM Switch Router ATMSwitch Router Quick Software Configuration Guide 5-2 C onfiguring Tag Switching on an ATM Switch Router This section describes how to configure tag.
Configuring Tag Switching 5-3 Enabling Tag Switching on the ATM Interface Examples Switch(config-if)# interface atm 1/0/1 Switch(config-if)# ip unnumbered loopback 0 Switch(config-if)# tag-switching ip Switch(config-if)# exit Switch(config)# Switch(config)# interface atm 0/0/3 Switch(config-if)# ip address 1.
Configuring Tag Switching on an ATM Switch Router ATMSwitch Router Quick Software Configuration Guide 5-4 Configuring the Routing Protocol Enable the routing protocol ( O SPF ) on the ATM switch router so that it can create routing tables, which identify routes through the network.
Configuring Tag Switching 5-5 Configuring the Routing Protocol Example Note An IP address of 1.1.1.1 with a subnet mask of 255.255.255.0 is entered as an IP network prefix of 1.1.1.0 with a subnet mask of 0.0.0.255. Likewise, an IP address of 1.2.1.1 with a subnet mask of 255.
Configuring Tag Switching on a Router ATMSwitch Router Quick Software Configuration Guide 5-6 Configuring Tag Switching on a Router This section describes how to configure tag switching between a router and an ATM switch router. Take these steps: Example Router# configure terminal Router(config)# interface atm 2/0.
Configuring Tag Switching 5-7 Tag Switching Configuration Example Verify Router# show tag-switching interface Interface IP Tunnel Operational ATM2/0.1 Yes No Ye s (ATM tagging) Tag Switching Configuration Example Figure5-1 shows an example tag switching network.
Tag Switching Configuration Example ATMSwitch Router Quick Software Configuration Guide 5-8 Router 5-2 Configuration The configuration between router R5-1, interface e0/1, and R5-2, interface e0/1, fo.
Configuring Tag Switching 5-9 Tag Switching Configuration Example The configuration of router R5-3, interface a2/0.1, follows: router_R5-3# configure terminal router_R5-3(config)# interface a2/0.1 router_R5-3(config-if)# ip address 189.25.12.13 255.255.
Tag Switching Configuration Example ATMSwitch Router Quick Software Configuration Guide 5-10 ATM Switch Router A6-4 Configuration The configuration of ATM switch router A6-4, interface a0/1/1, follows: atm_A6-4# configure terminal atm_A6-4(config)# interface a0/1/1 atm_A6-4(config-if)# no shutdown atm_A6-4(config-if)# ip address 189.
Index 1 INDEX A administrative access, configuring 2-4 B baud rate, for terminal emulation 1-1 BUS 4-3, 4-8 C card/subcard/port, defined 1-3 changes, saving 1-9 CLI, using 1-1to 1-10 command modes, un.
ATMSwitch Router Quick Software Configuration Guide Index 2 LEC 4-2, 4-5 LECS 4-2, 4-6 LES 4-3, 4-8 LES/BUS 4-8 M MAC addresses 4-2 modes, command 1-2 N naming the ATM switch router 2-1 numbering, car.
Index 3 U unauthorized access, preventing 2-3 undo See disabling V viewing the configuration 1-8 VP tunnels 3-21.
ATMSwitch Router Quick Software Configuration Guide Index 4.
Ein wichtiger Punkt beim Kauf des Geräts Cisco Systems 78-6897-01 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cisco Systems 78-6897-01 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cisco Systems 78-6897-01 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cisco Systems 78-6897-01 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cisco Systems 78-6897-01 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cisco Systems 78-6897-01 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cisco Systems 78-6897-01 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cisco Systems 78-6897-01. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cisco Systems 78-6897-01 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
