Benutzeranleitung / Produktwartung BE-0901E-AC-PC des Produzenten Brother
Zur Seite of 246
BE-0901E-AC-PC BE-1201B-AC-PC PC Control t ype Please read this manual be fore using the machine. Please kee p this m anual w ithi n easy reach for qui ck reference.
.
BE-0901E-AC-PC • BE-1201B-A C-PC 1 Thank you v ery much for buying a BROTHER sew ing machine. Before using your new machine, please read the safety instructions below and t he explanations given in the instruction manual.
2 BE-0901E-AC-PC • BE-1201B-A C-PC 2 Notes on safety DA NG ER Wait at least 5 m inutes after turnin g off the p ower s witch a nd disconn ectin g the p ower cord f rom the wa ll outlet bef ore o p enin g the f ace p late of the control box. T ouchin g areas where hi g h volta g es ar e p resent can resu lt in severe in jury .
BE-0901E-AC-PC • BE-1201B-A C-PC 3 Installation Avoid setting up the se wing m achine near sources of str ong electric al noise such as high-f requency weldi ng equipm ent. If this pr ecaution is not tak en, incorrec t machine o peratio n m ay result.
4 BE-0901E-AC-PC • BE-1201B-A C-PC Maintenance and inspection Maintenanc e and ins pection of the se wing machine s hould on ly be carr ied out b y a qual ified te chnician. Ask your Brother dealer or a qualif ied electrici an to car ry out an y mainten ance and inspect ion of the e lectrica l system .
BE-0901E-AC-PC • BE-1201B-A C-PC 5 3 W arni ng labels * The following warning labels appear on the sewing machine. Please follow the instr uctions on the labels at all times when using the machine. If the labels have been removed or are di fficult to read, please conta ct your nearest Brother dealer .
6 BE-0901E-AC-PC • BE-1201B-A C-PC ! ! ! ! BE-1201B- A C-PC W1750 3 5 4 Finger gua rd Bel t cover 3 4 2 6 1 Finger gua rd Guard cover ! ! ! ! BE-0901E-AC-PC.
BE-0901E-AC-PC • BE-1201B-A C-PC 7 Before S t arting Operation Do not for ce open the shutter f or direct c ontact with the m agnetic area. Do not bri ng disk s near magnetic matter s such as magnetic screwdri ver or the b ack s ide of the programm er .
8 BE-0901E-AC-PC • BE-1201B-A C-PC Protecting data in floppy disks Write-protection is av ailable for a floppy disk to prevent undesired dat a delet ion. A write-protected disk is read-only . It is recommended to pr ovide w r ite-protection f or disks which contain important data.
BE-1204B-BC • BE-1206B-B C 9 Procedure of Re ading This Manual Explanation of model s This manual explains two models: - BE-0901E-AC-PC - BE-1201B-AC-PC Explanation for individual model is provided by identifying the model name. Check t he model before using the machine.
10 BE-0901E-AC-PC• BE-1201B-A C-PC Contents Content s SAFETY INSTRUCTIONS............................................................................................................ ..................................... 1 Before St arting Operation .
BE-0901E-AC-PC • BE-1201B-A C-PC 11 Contents Chapter 4 Selecting and T ransferring E mbroidery Dat a Functions (Command Ref erence) .................................................................................................. ..................
12 BE-0901E-AC-PC• BE-1201B-A C-PC Contents Changing Dat a .................................................................................................................. .......................................... 5-23 Changing S tart ...........
BE-0901E-AC-PC • BE-1201B-A C-PC 13 Contents Setting the Machin e ....................................................................................................................................................6-25 Needle Bar ...................
14 BE-0901E-AC-PC• BE-1201B-A C-PC Contents Chapter 7 Operation of Machine 1. Operating Procedur es .............................................................................................................................................. 7-2 1-1 Power Source .
BE-0901E-AC-PC • BE-1201B-A C-PC 15 Contents Chap ter 9 Maintenan ce 1. Cleaning .....................................................................................................................................................................9-2 1-1 Cleaning a nd Lubrication of Rot ary Hook .
16 BE-0901E-AC-PC• BE-1201B-A C-PC Contents.
Chapter 1 An Introduction of Embroider y Machine.
1-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 1 An Introduction of Embroidery Machine 1. S pecificatio ns Embr oidery m achine used 9 needle em broider y m achine head 12 needle em broidery m achine hea d Applicat ion Pattern em broider y Sewing sp eed Maxim um 1200 rpm Sewing area Max.
BE-0901E-AC-PC • BE-1201B-A C-PC 1-3 Chapter 1 An Int roduction of Embroidery Machine.
1-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 1 An Introduction of Embroidery Machine 2. Sof tw are 2-1 Necessary S y stems The following systems are needed for installing the software.
BE-0901E-AC-PC • BE-1201B-A C-PC 1-5 Chapter 1 An Int roduction of Embroidery Machine 2-2 Configurati on of Sof tware This software is mainly composed of the following four programs.
1-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 1 An Introduction of Embroidery Machine Relationship among Programs W he n the software is s tarted, the program (1) for actuating the machine star ts first. Next, embroidery data is called by the program (2).
BE-0901E-AC-PC • BE-1201B-A C-PC 1-7 Chapter 1 An Int roduction of Embroidery Machine 2-5 Basic Operation of Sof t w are This section explains the basics of using the so ftware. It covers only the operating procedures that a r e commonly used for the softw are.
1-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 1 An Introduction of Embroidery Machine ! ! ! ! Double-click Press the left mouse button twice continuously . Do no t leave a long p ause in between. "Double-click [xx]" means moving the white arrow pointer to "xx" and p ressing the left button twice continuously .
BE-0901E-AC-PC • BE-1201B-A C-PC 1-9 Chapter 1 An Int roduction of Embroidery Machine Names of Screen Component s Names of major component s on the screen of the machine controller are described below : W1363Q ! ! ! ! Menu Processing of software is ca r ried out by givi ng relative commands.
1-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 1 An Introduction of Embroidery Machine Selectio n of Menu Processing of software is carried out by giving a com mand. A command can be given by the mouse as described below: 1. Move the arr ow pointer to a menu name and clic k there.
Chapter 2 Prep aration of Embroidery Machine.
2-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 1. Names of Ma chine Component s ! ! ! ! BE-0901E-AC-PC W1651 ! ! ! ! BE-1201B- A C-PC W1652 Thread guide bar Thread.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-3 Chapter 2 Preparation of Embroidery Machi ne 2. Inst allation DA NG ER Em broider y m achines s hould be installed o nl y by trai ned engin eers. Electr ic wiring s hould be laid by your distrib utor or elec tric ex perts.
2-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne Loosen thumb bolt [1]. Adjust the operation panel position for ease of use, and t ighten thumb bolt [1 ]. 2-3 Inst allation of Operation Panel W1653 2-4 Mounting of Guard Bar W1751 Attach guard bar [1] to the machine.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-5 Chapter 2 Preparation of Embroidery Machi ne 1. At tach two th read guide support bars [2] to the cotton stand assembly [ 1], while fitting into the two hol es. 2. Mount the thread guide assembly [3] on the thread guide support bar s [2] using t he two screws [4].
2-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 2-6 Lubrication to Needle Bar Case CA UTION Turn off the power switch before starti ng an y cleaning work , other wise the m achine m ay operate if the start switch is pres sed b y mistake, which co uld res ult in inj ur y .
BE-0901E-AC-PC • BE-1201B-A C-PC 2-7 Chapter 2 Preparation of Embroidery Machi ne 2-7 Connection of Personal Computer to Machines (fo r connecting 4 set s) Be sure to ground the per sonal computer . W1571 1. Turn of f the power of the personal co mputer and the machine.
2-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne W1656 4. Connect the control box connecto r SBUS2 of the first machine and the control box connector SBUS1 of the second machine using an IF cable. 5. Attach the side cover o f the con trol box.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-9 Chapter 2 Preparation of Embroidery Machi ne 2-8 Connection of Power Supply ! ! ! ! Connection of Power Supply of Embroidery M achine DA NG ER Be sure to con nect an e arth cable. Failure to do so m a y r esult in electric shock .
2-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! Uninterruptive po w er supply This unit is for protecting a personal computer from commercial power int erruption, voltage drop, and external noise. Use of an uninterruptive power supply is strongly recommended.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-1 1 Chapter 2 Preparation of Embroidery Machi ne 2-9 Inst allation of Sof tware Use an attached CD-R for installing software. If a personal computer with no CD-R drive unit is used, connect a drive unit to the co m puter .
2-12 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 3. Prep aration for Embroide ring CA UTION Turn off the power switch before s tarting preparatio n. Failure to do so m ay start the m achine uni ntentiona lly throug h an acc idental act ivation of th e ST ART switch , resulting in bodily injuries.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-13 Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! BE-1201B- A C-PC W1574 W1575 1. Pass an upper thread from the cotton stand through the holes of the thread guide right above each cotton stand bar .
2-14 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 1. O pen the rot ar y hoo k cover [1]. 2. Hold the knob [2] and ta k e out the bobbin case. 3. Close t he knob and take out the bobbin [3]. 1. Put a new bobbin in t he bobbin case.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-15 Chapter 2 Preparation of Embroidery Machi ne ! Attaching bobbin case W1581 3-3 Replacing and Select ing Needle W1582 * Relationship between materials and needles Material Needle Needle t hicknes s Denim Leather #14, #16, #18 Handker chief #9, #10 Shirt To w e l DB × K5 #1 1, #12, #13 [1] [2] 1.
2-16 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 3-4 Prep aration of Machine for Operat ion ! ! ! ! Check the follo wing before turning on the power Thread (1) A re.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-17 Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! When the mach i ne is turned on: "E-07" may appear on the operation p anel while a buzzer sounds intermittently .
2-18 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne If the machine is not ready to opera te because the needle bars in the driv e position are out of the normal position, "E-05" appears. Follow the steps below if this occurs.
BE-0901E-AC-PC • BE-1201B-A C-PC 2-19 Chapter 2 Preparation of Embroidery Machi ne 3-5 Att achment of Embroidery Hoop and Frame ! ! ! ! A ttaching a square frame and a flat hoop frame (st andard) W1591 1. Attach flat hoop frame (assembly) [1] to X carriage [2], and tighten two screws [3].
2-20 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! A ttaching a tubular round frame (optional) Note) W hen using a tubular r ound fr ame with the f ram e for it, rem ove table f rom the m achine. W1592 1. At tach two f rame sets [2] for tubular round frame to X carria ge [1] with two screws [3].
BE-0901E-AC-PC • BE-1201B-A C-PC 2-21 Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! A ttaching a sash frame set (optional) W1593 W1594 W1595 [6] [1] [6] [2] Projec tion Projec tion [3] [1] [4] [5] [7] 1. Turn of f the ma chine power sw itch. 2.
2-22 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne 5. Put mate rial over sash frame [8]. Att ach tw o clips 290 [9] to both v ertical sides securely . Also attach two clips 220 [10] to both horizontal sides securely .
BE-0901E-AC-PC • BE-1201B-A C-PC 2-23 Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! A djustment of upper thread Adjust upper thread tension to 0.
2-24 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 2 Preparation of Embroidery Machi ne ! ! ! ! Lo wer thread tension The standard tension of the lower thread is 0.15~ 0.3N. This tension m ay vary depending on the used thread. In general, press the bobbin case to a smooth vertical surface and hang the designated number of coins.
Chapter 3 Embroidering Procedures After installation of machine and setting-up of the personal computer (PC), st art embroidering. This chapter explains about the operation panel on the machine as well as precautions for the actual embroidering process.
3-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 3 Embroidering Procedures Functions of Oper ation Pane l Operation Panel W1667 S tarts em broidering. Restarts after moving the car riage to em broider ing start pos ition b y using the j og switc h. Restarts embr oidering after a s uspens ion.
B BE-0901E-AC -PC• BE-1201B -AC-PC 3-3 Chapter 3 Embroidering Procedures Check s the em broidering ar ea. Exits fr om embr oidering m ode. Press th is s witch while hold ing do wn swi tch simulta neously to stop embr oidering. Moves the hoop autom atical ly into t he embroider ing ar ea when th e embr oider y position is out of the are a.
3-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 3 Embroidering Procedures Flowchart of Prep arat ion for Embroiderin g Run PC. Run software ( → p age 3 -5) . Tu r n on the machine power . ( → pa ge 3-5) Register the m achine name for init ial start-up.
B BE-0901E-AC -PC• BE-1201B -AC-PC 3-5 Chapter 3 Embroidering Procedures Run the Sof tw are 1. Select [Program] - [Brother Embroidery System] – [Ecsc] from the S ta rt menu. The so ftware s tarts u p. T urn on the Machine Power W1596 W16 69 1. Chang e the Flat / Cap hoop select switch accor ding to the hoop to be used.
3-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 3 Embroidering Procedures Register the Machine Name Enter the machine name if the so ftware is run for the first time or when a new machine is connec t ed. 1. Ent er a machine na me. W1370Q 2. Click [OK].
B BE-0901E-AC -PC• BE-1201B -AC-PC 3-7 Chapter 3 Embroidering Procedures S t art Embro ide ring 1. Check t hat the READY lam p on the machine operation panel is on. W1372Q 2. Pr ess to check the embroidering area. 3. Pr ess t o sta rt embroidering .
3-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 3 Embroidering Procedures.
Chapter 4 Selecting and T ransferring Embroider y Dat a Clicking on the machine controller brings up a screen which allows selecting or transference o f registered embroidery data. M oving, copying, and deleting of embroidery data can also be car ried out on this screen.
4-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Functions (Command Re ference) File menu New Creates a new direc tory . ( → page 4-4) Exit of S electio n Transfers em broidery data to th e mac hine contro ller .
BE-0901E-AC-PC • BE-1201B-A C-PC 4-3 Chapter 4 Selecting and T ransf erring Embroidery Data Description of Screen W0964Q Exit of S election Exit Copy Move Dele te Rename List Image Sort by Name Sort.
4-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Creating a Director y Creates a new directory . A dire ctory can be cr eated w ithin another directory . 1. Click and select a p arent directory in the window on the left.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-5 Chapter 4 Selecting and T ransf erring Embroidery Data T ransferrin g dat a T r ansfer registered embroidery dat a to the machine con troller or Embroidery data editor . 1. Double- click data, or click data and .
4-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data 3. Set the number o f feeds for trim. Select the number of feeds or specify the feed length for trimmi ng and cl ick [OK ]. The data is transferred and t he explorer ends automati cally .
BE-0901E-AC-PC • BE-1201B-A C-PC 4-7 Chapter 4 Selecting and T ransf erring Embroidery Data Copy Copies embroidery data. ! Select from the menu or drag the data icon to the destination. Select from Me nu 1. Click data for selection. 2. Select [Copy] from Edit menu or click .
4-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Moving Dat a Moves embroidery data to a dif f erent directory . ! Select from the menu or drag the data icon to the destination. Select from Me nu 1. Click data for selection.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-9 Chapter 4 Selecting and T ransf erring Embroidery Data Deleting Dat a Deletes embroidery data. 1. Click data for selection. The frame of s elected dat a becomes red. 2. Select [Delete] from Edit menu or click . W0979Q 3.
4-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Recreat e an icon Creates an icon of data f or other models. ! Icons of the data c r eated by the f ollowing models can be recreated. • BE-1204B-BC • BE-1204C-BC • BE-1206B-BC • BE-0901E-AC • BE-1201B-AC 1.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-1 1 Chapter 4 Selecting and T ransf erring Embroidery Data Select A ll Selects all the data in the folder displayed. ! Only copying, movement, and deletion by d r ag & drop are enabled when multiple patterns are selected simultaneously .
4-12 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Renaming Dat a Renames the regist ered embroidery data. ! Data name consist s of the name area and three characters called "extension" w hich indicates data type.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-13 Chapter 4 Selecting and T ransf erring Embroidery Data Finding Da t a Retrieves and views embroidery data . 1. Select [Find Files] from T ool menu. 2. Ent er the file name of embroidery data for search . Enter the file name correctly .
4-14 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data If the specified embroidery data is found, the data is displayed. W0985Q Finding Files With W il dcard Charac ters W ildcard characters can be used as a substitute of a single character or multiple characters.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-15 Chapter 4 Selecting and T ransf erring Embroidery Data A djustin g Screen Display Selects the information type to display on the screen. ! T ool bar If it is checked, the tool bar appears. ! S tatus bar If it is checked, the status bar appears.
4-16 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Reading Dat a in F loppy Disk Reads data in a f loppy disk and registers it as embroidery data . ! The following data format s can be registered. • DOS format data T aji m a Dat a with file name "xxxx.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-17 Chapter 4 Selecting and T ransf erring Embroidery Data 4. Set feed counts for thread breaka ge. Select the numbe r of feeds or specify the feed length for trimmi ng and cl ick [OK ]. W0971Q 5. Select the directory to save and n ame the file.
4-18 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Converting the Non DOS format data This function is no t available with W indows NT. V iewing Fi les T o v iew files of FDR, FMC and ZSK dat a, carry out the following steps: ! Vi ewing Details Click .
BE-0901E-AC-PC • BE-1201B-A C-PC 4-19 Chapter 4 Selecting and T ransf erring Embroidery Data ! V iewi ng Icon Click . W0990Q ! Preview and Refresh The data ima ge can be display ed before reading the da ta. Click the desired icon or the name for display .
4-20 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data 3. Select data t o read and clic k [OK]. W0992Q W0993Q 4. T he image of the selected p attern appears. T o convert the selected data into ECS da ta. Click [OK].
BE-0901E-AC-PC • BE-1201B-A C-PC 4-21 Chapter 4 Selecting and T ransf erring Embroidery Data 5. Set feed counts for thread breakage. Select the number of feeds or specify the feed length for trimmi ng and cl ick [OK ]. W1403Q 6. Select the directory to save the file and name the file.
4-22 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Reading Dat a in Pape r T ape Saves data in p aper tape as embroidery dat a. ! Paper taper reader is required for reading data . ! Before saving any dat a, check that the p aper tape reader is connected to PC correctly .
BE-0901E-AC-PC • BE-1201B-A C-PC 4-23 Chapter 4 Selecting and T ransf erring Embroidery Data 5. T he image of the selected pattern appears. W0970Q 6. Select the directory to save and n ame the file. Do not change extens ion ".ECS". W0997Q 7.
4-24 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data Settings for Dat a Reading Sets up the interface and data transfer speed of the pape r tape reader or external disk drive. 1. Select [Setup] from T ool menu.
BE-0901E-AC-PC • BE-1201B-A C-PC 4-25 Chapter 4 Selecting and T ransf erring Embroidery Data W riting Dat a in DST F ormat Convert the ECS data into DST data for saving. 1. Click the desired ECS data t o convert into DST data. 2. Select [ECS to DST conv er sion] from T ool menu.
4-26 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 4 Selecting and T ransf erring Embroidery Data V iew ing Pattern Information Detail information of embroidery data can be checked. ! The following items can be chec ked. Pattern n ame File nam e and path of em broider y data File V er sion V ersion n um ber of the f ile No.
Chapter 5 Editing Embroidery Dat a Clicking of the machine controller brings up a screen which allow s edit ing of embroidery data. This screen allows simple processing of embroi- dery data and display setting o f display .
5-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Functions (Command Re ference) File menu Open Selects em broider y data. ( → page 5-5) Merge Add oth er pattern to the pattern in e ditin g. ( → page 5-28) Save Sa ves the ed ited em broidery data over t he curren t file .
BE-0901E-AC-PC • BE-1201B-A C-PC 5-3 Chapter 5 Editing Embroidery Data Microstitc h Displa ys the pos ition of the stitch whose lengt h is t he desig nated len gth or less. ( → page 5-9) Needle bar and spe ed range Displa ys the settin g screen f or needl e bar and sp eed rang e.
5-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Description of Screen W1000Q Status ba r Open Save Zoom Out Horizontal F lip V ertica l Flip Point Sym mentry Help T ool bar A .
BE-0901E-AC-PC • BE-1201B-A C-PC 5-5 Chapter 5 Editing Embroidery Data Opening Embroidery Dat a This function is available with embroidery data editor .
5-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Setting Display Sets the condition of t he display screen. It ems wi th check m arks to the left ar e selected. Centering Brings the i mage to the c enter of the screen. Before selecting After se lecting W1002Q W10 03Q 1.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-7 Chapter 5 Editing Embroidery Data Zoom Out 1. Select [Zoom] - [Zoom Out] f rom Vi ew menu or click . Repeats zooming of the ima g e by the numb er of clicks. Before selecting After se lecting W1004Q W10 05Q Range 1.
5-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Needle Penetration Chooses whethe r or not the nee dle pevetration p osit ions are di splayed.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-9 Chapter 5 Editing Embroidery Data Micros titch Displays the po sition of th e sti tch who se length is less th an th e desig nated length wi th . Len gth can be de sig nate d fro m 0. 0 to 1 .0 mm in un its of 0.
5-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Cha nge o f dis play c olor ! W he n the color of the embroidering sequence is changed, the color displayed on the screen is changed. W hen ending emb roidering or reading other data, the confirmation screen for saving the setting appears.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-1 1 Chapter 5 Editing Embroidery Data 2. Select a new color on the [Color selection] screen. W1018Q 3. W hen selecting a color from a color sample, click maker name or [User] and d ouble click [Color]. W1019Q 4. W hen finely adjusting t he selected color , click [ Medium color].
5-12 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data 5. Select an arbitrary color from basic colors. Click [Def ine Custom Colors] to create a medium color . W1021Q 6. Select a color by clic king on the color chart or by inputting a value, and click [OK].
BE-0901E-AC-PC • BE-1201B-A C-PC 5-13 Chapter 5 Editing Embroidery Data Changing needle bar allocation 1. Dr ag the embroidering sequence on t he needle bar numbe r . W1024Q Setting the rang e 1. Double click the desired needle bar ran ge to change.
5-14 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data T ool bar Shows/hides the to ol bar . The tool bar contains icons with the same functions a s the menu. 1. Select [T ool Bar ] from View m enu. Before selecting After se lecting W1028Q W10 29Q Stat us B ar Shows/hides the to ol statu s.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-15 Chapter 5 Editing Embroidery Data Back to Prev ious S tatus Undo Makes the edit or change invalid. The sc reen retu rns to the state before the change. ! The screen can re turn to 3 steps maximum. 1. Select [Undo] from the Edit menu or click .
5-16 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Editing Rot ate W0558Q ! A vailable range of rotation is -359 to 359 de g rees. ! W hen t he patterns to be repeated are grouped, the whole p at tern rotates. When t hey are not grouped, each pattern rota t es in each hoo p.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-17 Chapter 5 Editing Embroidery Data Horizo nt al Flip Flips the image horizontally . W0450Q W04 59Q 1. Select [Horizontal Flip] from Edit menu or click . V ertical F lip Flips the image vertically . W0450Q W04 60Q 1.
5-18 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data ! The number for repetition is 1 to 100 f or both vertical (Row) and horiz ontal (Column) directions. ! The unit for repetition can be set in inches . T o use the inch unit, set the length to [inch] on the [Configuration] of T ool menu of the machine controller .
BE-0901E-AC-PC • BE-1201B-A C-PC 5-19 Chapter 5 Editing Embroidery Data Margin setting with [ A ut o setting] selected The number is set automatically so as the number of repetitions to be the maximum within the sewing area.
5-20 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Resize Res ize s the i mage. W0450Q W13 95Q ! The available range of resizing is 50 to 200% in bot h the X and Y directions. ! Resizing changes the thread density alon g with the percenta ge.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-21 Chapter 5 Editing Embroidery Data Insert o r Delete C ode Codes of tr im, pause and colo r change can be inse rted or delete d by moving the ne edle to the desired position . 1. Select [Insert or delete code] from the Edit menu.
5-22 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Insert Lock S titch Find the pa ttern of [Sti tch] - [T rim] for [Befo re T rimming] an d find the pat tern of [T rim] - [Fee d] - [Stitch] - [Stitch] for [After T ri mming], then inse rt a lo ck stitch.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-23 Chapter 5 Editing Embroidery Data Changing Dat a Changing St art Changes the start position o f embr oidering. Options Functions Center , u pper left corner , m.
5-24 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Changing End Changes the end po sition of embroide ring. Options Functions Center , u pper left corner , m iddle l eft corner , lo wer left corner , m iddle top ed ge, m iddle bottom edge, upper right corner , m iddle rig ht corner , or lo wer right corn er of m ask .
BE-0901E-AC-PC • BE-1201B-A C-PC 5-25 Chapter 5 Editing Embroidery Data Mask Changes the mask tha t represen ts the periphe ry of embroidery data. Since the automa tic mask is a rectangle, the pa ttern within the hoop may be di splayed as an erro r .
5-26 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Group All patterns created in repetition are grouped as a sin gle pattern. ! The dif ference between the grouped p attern and the non-grouped p att ern is as follows: W1045Q W he n the p atterns are grouped • Each pattern is display ed in each mask.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-27 Chapter 5 Editing Embroidery Data Setting Group for Repeti tion 1. Select [Repeat] in the Edit menu or clic k . 2. Click the checkbox o f [Group] to put a check mark. W1033Q Selecting fr om Menu 1. Select [Group] from Change menu.
5-28 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Merge Merge other patterns to the pa t tern in editing. ! If the pattern to be merged is repetition data , it is automatically grouped and merged. ! If the pattern to be merged is grouped repetition data, it is merged at the specified position.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-29 Chapter 5 Editing Embroidery Data 3. T he pattern mask is displayed in a broken line. M ove the mask to the desired position for merging. Click the mouse. Move th e mouse w hile pre ssing the shift ke y . The mask move s horizon tally and v ertically .
5-30 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data Saving Dat a Saves the edited data. The edited data can be sav ed over the current file or renamed as a sep ar ate file. Save Saves the e dited data over the current file . The original da ta is deleted.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-31 Chapter 5 Editing Embroidery Data Save A s... Renames and sav es the edite d data as a new file. 1. Select [Save as...] from File menu. 2. Select the directory to save the new file. Enter a new f ile name. W1058Q 3.
5-32 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data V iew ing Pattern Information Detail information of embroidery data can be checked. ! The following items can be chec ked. No. of stitc hes The num ber of s titches in em broider y data No.
BE-0901E-AC-PC • BE-1201B-A C-PC 5-33 Chapter 5 Editing Embroidery Data Printing Dat a Prints data in editing. 1. Select [Print] from File menu or click .
5-34 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 5 Editing Embroidery Data.
Chapter 6 Embroidering The PC controls the m achine operation as w ell as set tin gs of the mach ine . Note tha t the menu which appears on the screen depends on whether the power to the machine is turned on or of f .
6-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Functions (Command Re ference) When the Po wer to the Machine is Off File m enu Save T he machine d ata is over written f or saving. ( → page 6-61) Save As The m achine data is saved as a differ ent name.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-3 Chapter 6 Embroidering Operation menu S tart Em broidering S tarts embr oidering. ( → page 6-52) St o p M a c h i n e Suspends embr oidering. ( → page 6- 53) Cancel Em broideri ng Cancels em broidering . ( → page 6-53) Home Pos ition Moves the home pos ition.
6-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Settin gs menu Needle Uses the sam e needle bar for all em broideri ng. ( → page 6-25) Same S peed Range Sets the head. ( → page 6- 26) Pause Sets whether to stop th e needle b ars tem porarily whe n changing al l the needle bars .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-5 Chapter 6 Embroidering Description of Screen W1060Q Needle bar and speed rang e Zoom in Zoom out Zoom in sp ecif ied rang e Fit to windo w Whole pat tern Needle .
6-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Settings before T urning On the Machine Describes settings available before the machine is turned on .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-7 Chapter 6 Embroidering Display i ng the St atus Bar Shows/hides the status ba r . The status bar provides in formation on the current status and advice for operation. 1. Select [S tatus Bar] from V iew menu and put the check mar k.
6-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Language Chang es display language. ! The following three languages are displayed as "A vailable Languag es". English Dis plays Eng lish. Languages system uses Displa ys the system languag e of PC.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-9 Chapter 6 Embroidering Settings af ter T urning Po w er On Describes settings available after turning power on to the machine. T ool Bar Shows/hides the to ol bar . The tool bar contains icons with the same functions a s the menu.
6-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Zoom In Specified Range Enlarges the range specified with the mo use to the full windo w size. 1. Select [Zoom In S pecified Range] from Display menu or click . The arrow pointer turns into .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-1 1 Chapter 6 Embroidering Grid Displays 1 × 1 cm square grids on the ba ckground. 1. Select [Grid] from Vi ew menu and put the chec k mark. Before selecting After se lecting W1071Q W10 72Q Hoop Displays the outline of embro idery hoop .
6-12 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 2. Desig nate the adjusting position and click [OK]. The hoop is di splayed in a dis placed positi on. W1075Q Before selecting After se lecting W1076Q W10 77Q Needle Penetration Chooses whethe r or not the nee dle pene tration posi tions are displayed.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-13 Chapter 6 Embroidering Thread Color Displays the pattern using colors currently set to the ne edle bar . Clicking also provide s the same fun ction. 1. Select [Thread Color] from Vi ew menu and pu t the check mark.
6-14 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Changing display colors ! The color of needle bar chan ges to the actual color . ! Changing the thread spool also changes the display color . A confirmation screen to save appears before exiting from embroidering or retrieving other data.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-15 Chapter 6 Embroidering 2. Select a new color on the [Color selection] screen. W1018Q 3. W hen selecting a color from a color sample, click maker name or [User] and d ouble click [Color]. W1019Q 4. W hen finely adjusting t he selected color , click [ Medium color].
6-16 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 5. Select an arbitrary color from basic colors. Click [Def ine Custom Colors] to create a medium color . W1021Q 6. Click the color chart or enter values to create a new color , and click [OK].
BE-0901E-AC-PC • BE-1201B-A C-PC 6-17 Chapter 6 Embroidering Setting Ranges There are two methods for se tting ranges. W1085Q Changing all ranges 1. Click [Up] to increase range. Click [Down] to reduce range. One clicki ng changes t he range by one level .
6-18 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Grid Sett ing Sets the pi tch and the color o f grid. ! The grid inte rva l can b e se t at the incre ment of 1 mm (0.1 inch for inch u ni t). ! The value for setting is 1 - 100 m m (0.1 - 10 inches for inch unit).
BE-0901E-AC-PC • BE-1201B-A C-PC 6-19 Chapter 6 Embroidering 2. Select or create the bac k ground color . Refer to steps 5 to 7 on p age 6-16 for det ails. Before changing the background co lor After changin g the backgroun d colo r W1091Q W10 92Q Renaming M achine Rename the regist ered machine.
6-20 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering V ie wing Machin e Infor mation Detail speci fication of the machine can be di splayed. 1. Select [Machine Information] from Machine menu. 2. Click [OK] after checking the information. W1094Q Design Information Detail speci fication of the embroidery data can be checked.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-21 Chapter 6 Embroidering 1. Select [Cascade] or [T ile] from W indow m enu. W1095Q When [Casc ade] is selec ted When [T ile] is se lected W1096Q W10 97Q Minimizi ng and Aligning Window s W indows on the screen can be minimized to the icon size and aligned.
6-22 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering A rrange Icons Minimized windows that are scattered can be ali gned. ! This command is available for minimized w indows. 1. Select [Arrange Icons] from W i ndow menu. W1 10 0Q 2. T he minimized w indows are aligned.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-23 Chapter 6 Embroidering Language Chang es display language. Refe r to p age 6- 8. Copy ing Dat a to Other Machin es When multiple m achines are c onnected, the embroi dery data of a machine can be copied to another machine.
6-24 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 4. Cli ck [OK ]. W1 10 5Q The data , is copied. W1 10 6Q Configurati on Sets the environ ment of data reading and display . 1. Select [Configuration] fr om T ool menu. 2. Click and select the item for setting.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-25 Chapter 6 Embroidering Setting the Machine Performs the detail setting of the embr oidering st atus. Items that can be select ed in Setting menu are explained here. Needle Bar Patterns ar e sewn by one nee dle. 1.
6-26 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Same Sp eed Range Embroiders pa tterns at th e spe cified speed range. 1. Select [Same S peed Range] from Settings menu. 2. Click a speed range f or selection. W 111 0 Q 3. Click [OK]. The speed ra nge appears at the s pecified ar eas.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-27 Chapter 6 Embroidering Speed Range Specifies th e maximum speeds for r espective range s suitabl e for the hoop type . ! Actual embroidering speed depends on the pitch. ! Before shipment, "1" is set to the highest speed; "6" is set to the lowest speed.
6-28 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Hoop Feed Position Set the ba sic posit ion of the hoop (hoop feed position) for cancellation of emb r oidering. ! The hoop feed position can be se t only in the embroidering area surrounded by a red frame.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-29 Chapter 6 Embroidering Embroidery A rea Sets the em broidery a rea. 1. Select [Embroidery Area] from Settings menu. 2. Dr ag the embroidery area using the mouse for designation. W 111 6 Q The embroi dery area is displ ayed in li ght blue.
6-30 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 1. Select [Embroidery Hoop] and the type from Settings menu. W1732 The patt e rn direction an d embroidering a rea may vary dependi ng on the sel ected embroidery hoop t ype. Make sure that the selection is correct.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-31 Chapter 6 Embroidering W1 12 0Q When “Se mi-wide cap (A LL)” is se lected. Thread T rimming ! The following items can be set: Enable inchin g Sets inc hing m otion for thr ead trim m ing. Hoop movem ent after thread trim ming Sets the need le penetr ation len gth for trim m ing.
6-32 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Boring ! The following items can be set. Boring Sets whether or not bor ing is perf orm ed by attachin g a bori ng knife to t he needle bar . Shift data Shifts the hoop b y 12 mm while th e needle b ar with a boring k nife attach ed is sele cted.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-33 Chapter 6 Embroidering Thread Breakage Sensor The sensor fo r thread breakage can b e turned ON/OFF o r the sensor sensitivity fo r each needle bar can be set. ! The sensitivity can be set within the range of 1 - 100.
6-34 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Automatic S tep Back Sets the numb er of stitche s for auto matic step bac k if thr ead breakage occur s. ! The number of stitches that can be se t is from 0 to 255. ! Additional step-back can be made f or sensitivity value of the thread breakage sensor .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-35 Chapter 6 Embroidering End of embroidery Sets if the machine returns to the start poin t after end o f embro idery . 1. Select [End of embroidery] from Settings menu. W1753 2. Click the checkbox to put a chec k mark ( ) w hen the machine returns to the start point a fter end of embroidery .
6-36 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Mendi ng Sets the de tails of mending . ! Items and descriptions are as follows: Automatic all y reset break age error Error is autom aticall y canceled when a thre ad break age occur s. 1.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-37 Chapter 6 Embroidering 2. Click [OK] when the items are set. W1 13 2Q Adj us t Adjustment valu e of the ne edle is set. ! The adjustment value is set at the increment of 0.1 mm. ! The setting range is -0.5 ~ 2 mm in X and Y directions.
6-38 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Driving shaf t Speeds u p the sta rtup of the ma in shaft . Select this func tion when sewing thick material. 1. Select [Driving shaft] from Settings menu and check it. W1738 2. W hen the item selection is completed, click [OK].
BE-0901E-AC-PC • BE-1201B-A C-PC 6-39 Chapter 6 Embroidering Short stitch speed reduct i on Reduces spee d when stitching in a designated pitch . ! The pitch can be desi gnated between 0.0 and 2.0 mm in units of 0.1 m m. ! The speed can be set between 400 rp m and the maximum speed o f the current hoop in unit s of 10 rpm.
6-40 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Thin / Thick Material Changes the timing o f needle drop and h oop movement. ! The timing can be switched for thick material or thin material. 1. Select [Thin / Thick material] from Settings menu.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-41 Chapter 6 Embroidering A rea T race Select the out s ide shape of area tracing before star ting sewing. ! The following two types can be selec ted. The selected outside shape is displayed on the s creen. Rectangl e Octagon W1 14 2Q W1 143Q 1.
6-42 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Default Settings Resets change s of the mach ine setting to the defaul t. ! Items for setting and initialization are as follows: S peed R ange Automatic all y selects the va lue suitable for the h oop t ype.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-43 Chapter 6 Embroidering 1. Sele ct [De faul t Se ttings] fr om S ettings menu. W1745 2. Click [OK]. Show Setting Shows the setting contents and defaults.
6-44 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 1. Sele ct [Show Settin g] from S etti ngs menu. W1746 2. Aft er chec king, check [OK]. W1648.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-45 Chapter 6 Embroidering Load Setting Load the setting. ! The set file has an extension of "ecm". 1. Select [Load setting] from Settings menu.
6-46 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Save Setting Saves the e dit settings. ! Save the setting files with an extension of "ecm". 1. Chang e the setting. 2. Select [Save setting] from Settings menu. W1755 3. Select the registration folder and put a file name.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-47 Chapter 6 Embroidering Load Hoop Load the optional hoop displayed in "Hoop" . ! The hoop file to be loaded has an extension of "ehp".
6-48 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering SPIDER _NET_FRAME 07T -3.ehp W1702 SPIDER _NET_FRAME 07T -4.ehp W1703 SPIDER _NET_FRAME 09T -1.ehp W0857Q SPIDER _NET_FRAME 09T -2.ehp W1704 SPIDER _NET_FRAME 09T -3.ehp W1705 SPIDER _NET_FRAME 09T -4.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-49 Chapter 6 Embroidering SPIDER _NET_FRAME 18T -1.ehp W0881Q SPIDER _NET_FRAME 18T -2.ehp W1722 SPIDER _NET_FRAME 18T -3.ehp W1723 SPIDER _NET_FRAME 18T -4.ehp W1724 SPIDER _NET_FRAME 19B.ehp W0885Q Tubular frame ◎ TUBULAR _FRAM E-05.
6-50 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering HOLDER_B ASE30X 28.ehp W0901Q HOLDER_B ASE30X 43.ehp W0902Q HOLDER_B ASE30X 48.ehp W1727 HOLDER_B ASE40X 43.ehp W1728 Tubular round fr ame ◎ TUBULAR _ROUND07.ehp W0905Q ◎ TUBULAR _ROUND09.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-51 Chapter 6 Embroidering 1. Select [Load hoop] from Se ttings menu. W1749 2. Select the folder a nd cl ick [Open ].
6-52 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Embroidering How to start embroidering and operation after the star t are explained here. St arting Embroidering ! The following screen appears when the edit data is retrieved fr om the explorer .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-53 Chapter 6 Embroidering 2. Pr ess the button. Embroidering starts. Embroidery data appears in gray , indicating the embroidering st a tus. W1 15 6Q Pause 1. Click . Can celing 1. Pr ess the button while pressing the button on the machine operation panel.
6-54 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Moving the Home Position Move the selected machine home position . 1. Select [Home Position] from Ope ration menu or click .
BE-0901E-AC-PC • BE-1201B-A C-PC 6-55 Chapter 6 Embroidering S t ep-forw ard/S tep-back Allows step-forward or step-back of stitches w ithout embroidering. ! Click to stop embroidering for step-forward/back mode. ! The special tool bar appears in the step-forward/back mode.
6-56 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Canceling step-forward/st ep-back 1. Click of the step f orward/back tool bar . The cross disappears and t he step forward/ba ck mode is canceled. W1 16 0Q Setting St ep-forw ard/Back Dist ance o r T i ming Select step -forwa rd/back distance or timing.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-57 Chapter 6 Embroidering Stepping Forward/Back Steps forward/bac k the stitche s actually . ! The functions of icons are as f ollows: W0927Q Returns to the start position. For re peating patterns, retu rns to the start pos ition of the current pattern.
6-58 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering 1. Select the icon and m ove the cross to the desired position for step forward/back. Forward B ackwar d W1 16 5Q W1 166Q S pecif y i ng the V alue S pecify the travel length from the embroidery star t point.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-59 Chapter 6 Embroidering Moving Embroidery Position Changes the position of embroidery data. ! Movement is allowed only in the embroidering area (within the red frame). 1. Select [Move Embroidery Position] from Operation menu or click .
6-60 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Centering Patte rn Moves the pattern to the machine home position. 1. Select [Move Pattern] f rom Operation menu.
BE-0901E-AC-PC • BE-1201B-A C-PC 6-61 Chapter 6 Embroidering Saving Dat a Saves the edited data. The edit ed data can be saved over the current file or renamed as a separate file. Save Saves the edited data ov er the current file. The original data is deleted.
6-62 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 6 Embroidering Running Othe r Programs Other programs can be st arted when the machine power is not turned on or when t he machine is in operation for embroidery . ! Th e fo llo wing p rogr am s ca n be start ed: Embr oidery data expl orer Allows tra nsfer and c opy of the embr oidery data.
Chapter 7 Operation of Machine.
7-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 7 Operation of Machine 1. Turn the power on to the machine. 2. W hen the machine is eq uipped with the shut-off sw it ch unit, Reset the emergency stop button. 3. W hen the machine is eq uipped with the shut-off sw it ch unit, Press the powe r switch.
BE-0901E-AC-PC • BE-1201B-A C-PC 7-3 Chapter 7 Operation of Machine 2. Machine Stop 2-1 Stopping the Machine w ith the stop switch unit W1607 ! ! ! ! Resetting Machine S top W1373Q 2-2 Emergency Sto.
7-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 7 Operation of Machine 3. Permission for Hoop M ovement W1374Q • When the compu ter has given a command to move the e mbroidery hoop, "HOOP" is displayed while blinking on the operation panel.
BE-0901E-AC-PC • BE-1201B-A C-PC 7-5 Chapter 7 Operation of Machine 4. Jog Sw itches 4-1 Hoop Movement to S t art Posi tion The hoop can be moved be f ore star ting embroidering and the start position can be set arbitrarily .
7-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 7 Operation of Machine 5. A r ea Chec k 5-1 Externa l T racing W1278Q If is p ressed in other cases than "area over", the rect angular outline of the p attern is traced. 5-2 Automatic Hoop Movement in A rea W1279Q • If "area over" is displayed, press .
BE-0901E-AC-PC • BE-1201B-A C-PC 7-7 Chapter 7 Operation of Machine 6. Hoop Fe ed Position • In order to ease m ounting and dismoun ting of the embroidery hoop, ano ther needle position can be set as a hoop feed position in the movable area addi tionally to the current needle position.
7-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 7 Operation of Machine 7. Measures again st Thread Bre akage 7-1 Remedies W1610 1. If embroidering is suspended due to thread breaka ge, “E- 0A” is displayed while blinking on the operation panel. 2. Cor rect the broken thread and p a ss it throu gh again.
BE-0901E-AC-PC • BE-1201B-A C-PC 7-9 Chapter 7 Operation of Machine 8. Inching Mode 8-1 Inching Mode duri ng Embroideri ng (Forcible Hoop Movement) • Movin g the f rame greatl y in the inching m ode m ay cause an interfer ence with the mac hine. Pay utm ost car e in the inc hing m ode.
7-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 7 Operation of Machine.
Chapter 8 Creating Production Report Records and controls th e machine operation. The production report can be created based on this data. Detaile d inf ormat ion of pr oductio n report allo ws effic ient embr oidering contr ol.
8-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Functions (Command Re ference) File menu Open Repor t File O pens the repor t file. ( → page 8- 4) Save As CSV Saves th e current r eport d ata in CSV f ormat. ( → page 8- 18) Print Prints the rep ort.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-3 Chapter 8 Creating Production Report Description of Screen W1 17 7Q Status bar Save as CSV Detaile d Data Thread Bre akage for Each Pattern Thread Bre akage for .
8-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Displaying Re port Displays the machine operation status in the form of report. ! The following reports can be display ed: Details Displa ys detail data while the mac hine is in operat ion.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-5 Chapter 8 Creating Production Report Display Example of Deta ils Displays the machine in formation ch ronologically that a re collected within the specified period . The following informat ion is indicated under the "Reason " column: Display Con tents Power O N The m achine po wer was tur ned on.
8-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Display Example of Thread Breakage Information on Needle Ba r Displays the information on thread brea k age occu rrences with head numbers an d needle bar numbers. Three needle bar s with frequent th read breakage are in dicated .
BE-0901E-AC-PC • BE-1201B-A C-PC 8-7 Chapter 8 Creating Production Report Display Example of Thread breakage Information in Pa ttern Displays thr ead brea kage infor mation fo r each p attern. Display Con tents n th The pattern was embr oidered for th e "n"th t ime.
8-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Display Example of Output Information Displays the production information that a re collected during the speci fied perio d.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-9 Chapter 8 Creating Production Report Det ails of reas on for stopp age Interrupt ed Frequency and t otal time s topped b y the operator S toppage du e to thre ad.
8-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Display Example of T ot al Output Inform ation Displays the out put information per pattern on multiple machines that are s elected. Display Con tents Number The pattern embroider ed durin g the specif ied p eriod is n umber ed.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-1 1 Chapter 8 Creating Production Report Disp lay in graph The total output information is displayed with the graph. Displayed here is the screen of the number of embroidered cloths. W1 18 6Q Click tab to display the total e m broidering time, etc, with the graph.
8-12 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Setting Display Items Sets display items for each p roduction report. ! The following tab wi ndows can be set: General Item s related to the overall d isplay of the output r eport.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-13 Chapter 8 Creating Production Report ! Collate Selects the data collection period. If month, week or day is selected , set the end date or end hour . ! St o r a g e Selects the data save period. Det a ils W1 18 8Q ! Main items to be displayed Displays each event and the time.
8-14 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Thread Breakage Info rmation on Needle Bar W1 18 9Q ! Main items to be displayed No.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-15 Chapter 8 Creating Production Report Outpu t Informa tion T ime is calcu lated to the unit of secon d , but the display unit is in minute. This may re sult in minor diffe rences. W1 19 1Q ! Items to be display ed T otal stitches The total num ber of em broidery st itches f rom s tart to end No.
8-16 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report T ot al Outp ut In format ion T ime is calcu lated to the unit of secon d , but the display unit is in minute. This may re sult in minor diffe rences. W1 19 2Q ! Items to be display ed T otal stitches The total number of embr oidery stitches from start to end No.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-17 Chapter 8 Creating Production Report Recess T ime Setting Sets the ti me not to be in cluded in the cal culation. Thi s time is displayed on the " Output" r eport as "Time Exc lud ed". W1 19 3Q ! T ar get machine Click and select the applicable machine for calculation.
8-18 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Save A s CSV ... Converts the production report dat a to CSV format that can be read in spreadshee t software. 1. Select [Save As CSV] from File menu o r click . 2. T he file name "Untitled.
BE-0901E-AC-PC • BE-1201B-A C-PC 8-19 Chapter 8 Creating Production Report Printing Productio n Report Prints the production r eport from a pr inter . Page Setup Printing metho d is set as requ ired. 1. Select [P age setup] from the Fi le menu. Setting screen is d isplaye d.
8-20 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 8 Creating Production Report Copying Report Da t a Copies the selected area as text data. This allow s use of the production report on othe r word processing sof tware . 1. Select [Select All] from Edit menu, or drag and select the area to be copied.
Chapter 9 Maintenance.
9-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 9 Maintenance CA UTION Turn off the power switch before starti ng mainte nance. Failure to do so m ay start the m achine uni ntentiona lly throug h an acc idental activ ation of th e ST ART switch , resulting in bodily injuries.
BE-0901E-AC-PC • BE-1201B-A C-PC 9-3 Chapter 9 Maintenance 1-2 Cleaning of Need le Plate Broken threads left around the movable or fixed knives or the thread holding plate may result in thread trimming failur e or p arts da mage. Clean them once a month.
9-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 9 Maintenance 2. Oiling T o ex tend the machine's service life, supply oil to the following places at re gular int ervals. The models BE-0901E-AC-PC and BE-1201B-AC-PC adopt centralized wick lubrication (including rotary hoo ks).
BE-0901E-AC-PC • BE-1201B-A C-PC 9-5 Chapter 9 Maintenance ! BE-1201B-AC-PC W1616 ! Daily oiling W1617 Supply oil to the top and the bo t tom of each needle bar (24 points ) daily as shown in the fi gur e. Supply oil to the points indicated by the arrows in the figure.
9-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 9 Maintenance ! Before operation. Before starting operation of the machine, move the needle case fully to the ri ght and the left, and use a cloth to wip.
Chapter 10 Adjustment.
10-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 10 Adjustment CA UTION If adjus tment should b e m ade while the power switch is turned on, pay speci al attenti on to your safe ty . Turn off the p ower s witch and p ull o ut th e p lu g before s tarting adjustm ent.
BE-0901E-AC-PC • BE-1201B-A C-PC 10-3 Chapter 10 Adjustment 1. Dism ount the pulley cov er and turn the pulley [1] until the pulley scale indicates 180° and the needle bar is set at the lowest position. (The pulley " " mark and the s t op mark " " a re aligned.
10-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 10 Adjustment ! W he n using the bottom dead cente r gauge W1619 W1621 W1222 W1624 W1625 [5] [6] [4] [1] [7] [8] [9] [3] [3] Tighten the bolt [9] so that the cleara nce can be even. Do not hit this sect ion.
BE-0901E-AC-PC • BE-1201B-A C-PC 10-5 Chapter 10 Adjustment 1. Turn the pulley [1] until the scale of pulley [1] indicates 180° (where the pulley indicat ion mark " " and the stop mark " " are aligned) and the needle bar is set at the low est position.
10-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 10 Adjustment 2. Adjust ment of T iming Betw ee n Needle and Rot ary Hook W1626 1. Select needle bar No. 1. The above figure sh ows mode l BE-0901E-AC-PC. For mo del BE-1201B- AC-PC, nee dle bar No. 12 corresponds to y .
BE-0901E-AC-PC • BE-1201B-A C-PC 10-7 Chapter 10 Adjustment 3. A d justment of Presser Foot Height W1627 W16 28 W1629 1. Turn the pow er switch off. 2.
10-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 10 Adjustment 4. A djustment of Thread T rimmer W1630 W1631 [1] [2] 10mm [3] [4] [5] 1.2mm 1. Br ing fixed knife e into contact w it h spring pin [2] of needle plate base [1], and tighten the screw .
BE-0901E-AC-PC • BE-1201B-A C-PC 10-9 Chapter 10 Adjustment 5. Thread Wiper A dju stment W1632 ! ! ! ! BE-1201B- A C-PC W1633 1. Move solenoid arm [1] in the direction o f the arrow w it h y our finger . Loosen three bol ts [3] and adjust t hread hook [2] for sm ooth movements.
10-10 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 10 Adjustment 6. A d justing the Belt T ension The belt T ension is adjusted to the optimum tension at the time of shipment from the factory . However , as the belt is used ,it becomes run in and may loosen around the ma chine pulley and mo tor pulley .
Chapter 1 1 Error code list.
11 - 2 BE-0901E-AC- PC• BE-1201B -AC-PC Chapter 1 1 Error code list Code Error Measures E-00 No error occurs. E-01 E-01ERROR 01Eith er motor of m ain sha ft, X - or Y -ax is has locked.. This is not usually dis played. E-02 Overtrav el occurs during home posit ion detecting m ovement.
BE-0901E-AC-PC • BE-1201B-A C-PC 11 - 3 Chapter 1 1 Error code list Code Error Measures E-21 Hoop overh ang (+X ) E-22 Hoop overh ang (+Y ) E-23 Hoop overh ang (+X , +Y) E-24 Hoop overhang (-X ) E-2.
11 - 4 BE-0901E-AC- PC• BE-1201B -AC-PC Chapter 1 1 Error code list Code Error Measures E-CB S pindle rota tion speed error Press the to cancel the error and pre ss the If the same error occur s again, ther e is a possi bility that the spindl e is overloaded.
Chapter 12 T roubleshooting If there is any indication of trouble with the machine, check and correct as described in t he table. If the trouble cannot be corrected, turn o ff the pow er and contact your distributor for corrective actions.
12-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 12 Troubleshooting Mechanical Section Problem Check point ! Thread br eakage • Is the m achine pr operl y threaded? • Is thread tension t oo high? .
BE-0901E-AC-PC • BE-1201B-A C-PC 12-3 Chapter 12 Troubleshooting Problem Check point ! Machine o peratio n abnorm al • Is any set sc rew of the ro tary encod er loosene d? • Is an y set screw of.
12-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 12 Troubleshooting Electrical Section Cautions • Be sure to turn of f the pow er of the machine and unplug the pow er cord before checking cable connections. • When y ou check connection of the cables as instructed in this manual, also check connection and continuity between connectors.
BE-0901E-AC-PC • BE-1201B-A C-PC 12-5 Chapter 12 Troubleshooting Symptom Meas ures The need le bar cas e lock error occurs. • Is the INDEX motor rotating? → If not, ref er to the b lock diagr am s howing the c able connec tions and chec k to see if connecti on from the INDEX m otor to the m ain PCB is pr oper .
12-6 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 12 Troubleshooting Symptom Meas ures The m ain shaft motor loc k error occurs. • Enter the encoder signal mode a nd manuall y turn the main shaft pulle y . → If it is ab norm ally heav y , the m ain shaft m echanism is fault y .
BE-0901E-AC-PC • BE-1201B-A C-PC 12-7 Chapter 12 Troubleshooting Symptom Meas ures Jump s olenoid does not oper ate. • Check to see if c onnection from the j um p solenoid to con nector P10 of the head PCB is proper . • Check the resistance value of the jum p soleno id which does not operate with the con nector s ection.
12-8 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 12 Troubleshooting.
Chapter 13 Connection and Inst allation of Optional Equipment.
13-2 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 13 Connection and Installation of Opti onal Equipment 1. A tt aching Bobbin Winder ! Mounting method W1636 W1637 3.
BE-0901E-AC-PC • BE-1201B-A C-PC 13-3 Chapter 13 Connection and Installation of Opti onal Equipment ! W indin g lower thread W1638 1. Turn on t he power switch. 2. Fit bobbin [1] to the bobbin winder sha ft [2]. 3. Pass a thread through thread guide [3].
13-4 BE-0901E-AC-PC • BE-1201B -AC-PC Chapter 13 Connection and Installation of Opti onal Equipment.
.
INSTRUC TION MANUAL BROTHER INDUSTRIE S, L TD. http://w ww .b rother .com/ 15-1.Naeshiro-cho, Mizuho-ku , Nagoya 467-8561, Jap an. Phone: 81- 52-824-2177 Printed in Ja pan BE-0901E-AC-PC, BE-1201B-AC-.
Ein wichtiger Punkt beim Kauf des Geräts Brother BE-0901E-AC-PC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Brother BE-0901E-AC-PC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Brother BE-0901E-AC-PC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Brother BE-0901E-AC-PC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Brother BE-0901E-AC-PC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Brother BE-0901E-AC-PC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Brother BE-0901E-AC-PC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Brother BE-0901E-AC-PC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Brother BE-0901E-AC-PC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
