

elements. Children less than 8 years of age shall be kept away unless continuously supervised.

Use



1 Induction cooking zone

Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which functions operate.

1 ON / OFF To activate and deactivate the hob.
2 Lock / The Child Safety Device To lock / unlock the control panel.
To show for which zone you set the time.
2 Control panel

7 / - To increase or decrease the time.
8 / - To set a heat setting.
9 Power function To activate and deactivate the function.
The cooking zone is deactivated.
- The cooking zone operates.
Automatic Heat Up function operates.
Power function operates.
+ digit There is a malfunction.
A cooking zone is still hot (residual heat).
Lock / The Child Safety Device function operates.
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off function operates.
The induction cooking zones make the heat necessary for cooking process directly in the bottom of the cookware. The glass ceramic is heated by the heat of the cookware.
There is a risk of burns from residual heat.
The function deactivates the hob automatically if:
Touch for 1 second to activate or deactivate the hob.

To activate the function for a cooking
zone if there is no on the display: touch
then chose the highest heat setting 9 and
touch again. Immediately touch to set a desired heat setting.
To deactivate the function: change the heat setting.
This function makes more power available to the induction cooking zones. The function can be activated for the induction cooking zone only for a limited period of time. After this time the induction cooking zone automatically sets back to the highest heat setting.
change the heat setting. After some time comes on and the hob deactivates. The relation between the heat setting and the time after which the hob deactivates:
Refer to “Technical information” chapter.
Heat setting The hob deacti-
To activate the function for a cooking
, 1 - 2 6 hours
zone: touch . comes on.
To deactivate the function: touch or .
Count Down Timer You can use this function to set how long the cooking zone should operate for a single cooking session.
Touch to increase the heat setting. Touch
First set the heat setting for the cooking zone then set the function.
to decrease the heat setting. Touch and
at the same time to deactivate the cooking zone.
To set the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on.
If you activate this function you can get a necessary heat setting in a shorter time. The function sets the highest heat setting for some time and then decreases to the correct heat setting.
To activate the function or change the
time: touch or of the timer to set the time (00 - 99 minutes). When the indicator of the cooking zone starts to flash slowly the time counts down.
To activate the function the cooking zone must be cold.
zone with . The indicator of the cooking zone starts to flash quickly. The display shows the remaining time.
To activate the function for a cooking
touch ( comes on). Immediately touch until the correct heat setting comes on. After 3
zone with and touch . The remaining time counts back to 00. The indicator of the cooking zone goes out.
seconds comes on.
To deactivate the function: touch .
vates after · 5 4 hours

When the time comes to an end, the sound operates and 00 flashes. The cooking zone deactivates.
for 4 seconds. comes on. Deactivate the
hob with .
To override the function for only one
To stop the sound: touch .
cooking time: activate the hob with .
Minute Minder You can use this function as a Minute Minder when the hob is activated and the cooking zones do not operate. The heat setting display
comes on. Touch for 4 seconds. Set the heat setting in 10 seconds. You can operate
the hob. When you deactivate the hob with the function operates again.
shows .
or of the timer to set the time. When the time comes to an end, the sound operates and 00 flashes.
To stop the sound: touch .
The function has no effect on the operation of the cooking zones.
You can lock the control panel while cooking zones operate. It prevents an accidental change of the heat setting.
Set the heat setting first.
To activate the function: touch . comes on for 4 seconds. The Timer stays on.
To deactivate the function: touch . The previous heat setting comes on.
When you deactivate the hob, you also deactivate this function.
This function prevents an accidental operation of the hob.
with . Do not set the heat setting. Touch
for 4 seconds. comes on. Deactivate the
hob with .
with . Do not set the heat setting. Touch

smaller diameter than the minimum receives only a part of the power generated by the cooking zone.
For induction cooking zones a strong electro-magnetic field creates the heat in the cookware very quickly.
Refer to “Technical information” chapter.
Use the induction cooking zones with correct cookware.
If you can hear:
The bottom of the cookware must be as thick and flat as possible.
The relation between the heat setting and the cooking zone consumption of power is not linear. When you increase the heat setting, it is not proportional to the increase of the cooking zone consumption of power. It means that the cooking zone with the medium heat setting uses less than a half of its power.
Induction cooking zones adapt to the dimension of the bottom of the cookware automatically to some limit.
The cooking zone efficiency is related to the diameter of the cookware. The cookware with a
The data in the table is for guidance only.
- 1 Keep cooked food warm. as neces- sary
Put a lid on the cookware.
Cookware material · Cookware dimensions

Turn halfway through.
9 Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.
Boil large quantities of water. Power function is activated.
What to do if...
Problem Possible cause Remedy
You cannot activate or operate the hob.
The hob is not connected to an electrical supply or it is connec- ted incorrectly.
Check if the hob is correctly con- nected to the electrical supply. Refer to the connection diagram.
as neces- sary

Problem Possible cause Remedy
The fuse is blown. Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a qualified electrician.
Activate the hob again and set the heat setting in less than 10 seconds.
You touched 2 or more sensor fields at the same time.
Touch only one sensor field.
There is water or fat stains on the control panel.
Clean the control panel.
An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated.
You put something on one or more sensor fields.
Remove the object from the sen- sor fields.
The hob deactivates. You put something on the sensor
Remove the object from the sen- sor field.
field .
Residual heat indicator does not come on.
The zone is not hot because it operated only for a short time.
If the zone operated sufficiently long to be hot, speak to an Au- thorised Service Centre.
Automatic Heat Up function does not operate.
The zone is hot. Let the zone become sufficiently cool.
The highest heat setting is set. The highest heat setting has the same power as the function.
The heat setting changes be- tween two levels.
Power management function op- erates.
Refer to "Daily use" chapter.
The sensor fields become hot. The cookware is too large or you put it too near to the controls.
Put large cookware on the rear zones if possible.
comes on. Automatic Switch Off operates. Deactivate the hob and activate it again.
comes on. The Child Safety Device or the Lock function operates.
Refer to "Daily use" chapter.
comes on. There is no cookware on the zone.
Put cookware on the zone.
The cookware is incorrect. Use the correct cookware. Refer to “Hints and tips” chapter.

Problem Possible cause Remedy
The diameter of the bottom of the cookware is too small for the zone.
Use cookware with correct di- mensions. Refer to “Technical information” chapter.
and a number come on. There is an error in the hob. Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house.
Connect it again. If comes on again, speak to an Authorised Service Centre.
comes on. There is an error in the hob be- cause a cookware boiled dry. Au- tomatic Switch Off and the over- heating protection for the zones operate.
Deactivate the hob. Remove the hot cookware. After approximate- ly 30 seconds, activate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware be- come sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter.
If you cannot find a solution...
Make sure, you operated the hob correctly. If not the servicing by a service technician or dealer will not be free of charge, also during the warranty period. The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet.
If you cannot find a solution to the problem yourself, contact your dealer or an Authorised Service Centre. Give the data from the rating plate. Give also three digit letter code for the glass ceramic (it is in the corner of the glass surface) and an error message that comes on.
Before you install the hob, write down the information bellow from the rating plate. The rating plate is on the bottom of the hob.
Serial number
Only use the built-in hobs after you assemble the hob into correct built-in units and work surfaces that align to the standards.






Protection box If you use a protection box (an additional accessory), the front airflow space of 2 mm and the protective floor directly below the hob are not necessary. The protection box accessory may not be available in some countries. Please contact your local supplier.
You can not use the protection box if you install the hob above an oven.
Model ZEL6640FBA PNC 949 595 594 01 Typ 60 GAP D5 AU 220 - 240 V 50 - 60 Hz Induction 7.4 kW Made in Germany Ser.Nr 7.4 kW ZANUSSI

The power of the cooking zones can be different in some small range from the data in the table. It changes with the material and dimensions of the cookware.
For optimal cooking results use cookware not larger than the diameter in the table.

Type of hob Built-In Hob
Number of cooking zones 4
Diameter of circular cooking zones (Ø)
Left front Left rear Right front Right rear
21.0 cm 18.0 cm 14.5 cm 18.0 cm
Energy consumption per cook- ing zone (EC electric cooking)
Left front Left rear Right front Right rear
168.0 Wh / kg 183.0 Wh / kg 174.0 Wh / kg 179.0 Wh / kg
Energy consumption of the hob (EC electric hob)
176.0 Wh / kg
EN 60350-2 - Household electric cooking appliances - Part 2: Hobs - Methods for measuring performance
You can save energy during everyday cooking if you follow below hints.
Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose
appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
Model identification ZEL6640FBA · Heating technology Induction
Häufige Probleme, wahrscheinliche Ursachen und Lösungen.
| Problem | Mögliche Ursache | Abhilfe | |
|---|---|---|---|
| You cannot activate or operate the hob. | The hob is not connected to an electrical supply or it is connec- ted incorrectly. | Check if the hob is correctly con- nected to the electrical supply. Refer to the connection diagram. | p.10 |
| The fuse is blown. | Make sure that the fuse is the cause of the malfunction. If the fuse is blown again and again, contact a qualified electrician. | p.11 | |
| Activate the hob again and set the heat setting in less than 10 seconds. | p.11 | ||
| You touched 2 or more sensor fields at the same time. | Touch only one sensor field. | p.11 | |
| There is water or fat stains on the control panel. | Clean the control panel. | p.11 | |
| An acoustic signal sounds and the hob deactivates. An acoustic signal sounds when the hob is deactivated. | You put something on one or more sensor fields. | Remove the object from the sen- sor fields. | p.11 |
| The hob deactivates. | You put something on the sensor field . | Remove the object from the sen- sor field. | p.11 |
| Residual heat indicator does not come on. | The zone is not hot because it operated only for a short time. | If the zone operated sufficiently long to be hot, speak to an Au- thorised Service Centre. | p.11 |
| Automatic Heat Up function does not operate. | The zone is hot. | Let the zone become sufficiently cool. | p.11 |
| Automatic Heat Up function does not operate. | The highest heat setting is set. | The highest heat setting has the same power as the function. | p.11 |
| The heat setting changes be- tween two levels. | Power management function op- erates. | Refer to "Daily use" chapter. | p.11 |
| The sensor fields become hot. | The cookware is too large or you put it too near to the controls. | Put large cookware on the rear zones if possible. | p.11 |
| comes on. | Automatic Switch Off operates. | Deactivate the hob and activate it again. | p.11 |
| comes on. | The Child Safety Device or the Lock function operates. | Refer to "Daily use" chapter. | p.11 |
| comes on. | There is no cookware on the zone. | Put cookware on the zone. | p.11 |
| comes on. | The cookware is incorrect. | Use the correct cookware. Refer to “Hints and tips” chapter. | p.11 |
| The diameter of the bottom of the cookware is too small for the zone. | Use cookware with correct di- mensions. Refer to “Technical information” chapter. | p.12 | |
| and a number come on. | There is an error in the hob. | Disconnect the hob from the electrical supply for some time. Disconnect the fuse from the electrical system of the house. Connect it again. If comes on again, speak to an Authorised Service Centre. | p.12 |
| comes on. | There is an error in the hob be- cause a cookware boiled dry. Au- tomatic Switch Off and the over- heating protection for the zones operate. | Deactivate the hob. Remove the hot cookware. After approximate- ly 30 seconds, activate the zone again. If the cookware was the problem, the error message goes out. Residual heat indicator can stay on. Let the cookware be- come sufficiently cool. Check if your cookware is compatible with the hob. Refer to “Hints and tips” chapter. | p.12 |
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.