
Unpack all the materials. The installation and connection of this appliance has to be done by approved specialists.
The manufacturer cannot be held responsible for damage caused by building-in or connection errors. This appliance can only be used when installed in a well-equipped kitchen unit with an
adapted and approved work-surface. This domestic appliance is exclusively for the cooking of food, to the exclusion of any other
domestic, commercial or industrial use. Remove all labels and self-adhesives from the ceramic glass. Do not change or alter the appliance. The cooking plate cannot be used freestanding nor can it be used as a work-surface. The appliance must be grounded and connected in accordance with local standards. Do not use any extension cord to connect it. The appliance cannot be used above a dishwasher or tumble-dryer: steam may damage
the electronic appliances.
Switch the heating zones off after use. Keep an eye on the food when using grease or oils: it may quickly ignite. Be careful not to burn yourself while or after using the appliance. Make sure no cable of any fixed or movable appliance comes in contact with the glass or
the hot saucepan. Magnetic objects (credit cards, floppy disks, calculators) should not be placed near the
appliance when it is running. Metallic objects such as knives, forks, spoons and lids should not be placed on the hob
because they can get hot. Use proper induction saucepans. In general, do not place any metallic object on the glass
surface, except heat-resistant containers. If the appliance is switched on too soon or in case of residual heat, other materials could melt or ignite. Never cover the appliance with a cloth or a protection sheet. It can get very hot and catch
fire. This appliance cannot be used by people (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they are given supervision or instruction concerning the use of the appliance by someone responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Raw pan bottoms or damaged saucepans (not enamelled cast iron pots,) may damage the
ceramic glass. Sand or other abrasive materials may damage the ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. Do not hit the edges of the glass with a saucepan. Make sure that the ventilation system of the appliance works according to the
manufacturer’s instructions. Do not put or leave empty saucepans on the vitroceramic hobs. Sugar, synthetic materials or aluminium sheets must not be exposed to hot areas. These
may cause cracks or other alterations of the vitroceramic glass by cooling: switch the appliance off and remove them immediately (be careful: do not burn yourself). Never put any hot container on the control panel. If a drawer is situated under the embedded appliance, make sure the space between the
content of the drawer and the inferior part of the appliance is large enough (2 cm). This is essential to guarantee correct ventilation. Never put an inflammable object (e.g. spray) in the drawer situated under the vitroceramic
hob. Any cutlery drawer must be heat-resistant.
In case of a malfunction, switch off the appliance and turn off the electrical supply. If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the
after sales service. Repair should be done by specialists. Do not open the appliance yourself. WARNING: If the surface is cracked, switch off the appliance to avoid the possibility of an
electric shock.
Make sure that the pan is always placed in the middle of the cooking zone. The bottom of
the pan has to cover the cooking zone as much as possible. For people with a pacemaker, the magnetic field could influence its function. We
recommend you to retrieve further information from the retailer or the doctor. Do not use aluminium or synthetic containers: they can melt on hot cooking zones.
THE USE OF EITHER POOR QUALITY POTS OR ANY INDUCTION ADAPTOR PLATE FOR NON-MAGNETIC COOKWARE RESULTS IN A WARRANTY BREACH.
IN THIS CASE, THE MANUFACTURER CANNOT BE HELD RESPONSIBLE
FOR ANY DAMAGE CAUSED TO THE HOB AND/OR ITS ENVIRONMENT.

Type Total Power Heating zone Nominal
1st Booster Power*
2nd Booster Power*
3700 W 2 zones 220 x 180 mm 2100 W 2600 W 3700 W 100 mm
3772 Wok 3200 W 314 mm 2000 W 2500 W 3200 W -
* The given power may change according to the dimensions and material of the pan.
Timer display Power display Keep warm



On/Off key Locking key

Display Designation Description 0 Zero The heating zone is activated. 1…9 Booster level Selection of the cooking level. U No pan detection No pan or inadequate pan. A Heat accelerator Automatic cooking. E Error message Electronic failure. H Residual heat The heating zone is hot. P Power The Power is activated.
Super Power The Super Power is activated. U Keep warm Maintain automatically 42, 70 or 94°C. II Stop&Go The hob is in pause.
The cooling system is fully automatic. The cooling fan starts at a low speed when the calories generated by the electronic system reach a certain level. The ventilation starts its high speed level when the hob is intensively used. The cooling fan reduces its speed and stops automatically when the electronic circuit has cooled down enough. STARTING-UP AND APPLIANCE MANAGEMENT
Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent because this can create a blue-tinted colour on the glass surface.
An induction coil is located under each heating zone. When it is working, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone. Of course the pan has to be adapted:
All ferromagnetic pans are recommended (please verify this thanks to a little magnet): cast
iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms,…(see also p. 57 Pan quality) Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic, stoneware,… The induction heating zone adapts automatically to the size of the pan. With a diameter that is too small, the pan doesn’t work. This diameter varies in function of the heating zone diameter. If the pan is not adapted to the induction hob , the display will show [ U ].
Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. In case of normal use, press only one key at a time.

To select the power with the slider, slide your finger on the “SLIDER” zone. You can already have direct access if you put your finger directly on the chosen level.
Power selection zone “SLIDER” and

Start up / switch off the hob: Action Control panel Display To start press key [ 0/I ] [ 0 ] To stop press key [ 0/I ] nothing or [ H ]
Start up / switch off a heating zone: Action Control panel Display To set slide on the “SLIDER“ [ 1 ] to [ P ] (adjust the power) to the right or to the left To stop slide to [ 0 ] on “SLIDER“ [ 0 ] or [ H ] If no action is taken within 20 seconds ,the electronics return in waiting position.
timer setting zone · “SLIDER“ Direct access

Pan detection This cooktop is fitted with an interactive control system that makes it very easy and comfortable to use. After switching on the cooktop, when you put a cookware on the glass, the control system automatically detects it. This system also automatically indicates you which slider control to use by displaying a [ 0 ] over it. You then just have to set the expected cooking level. Pan detection ensures a perfect safety. Induction does not work:
If there is no pan on the heating zone, or if this pan is not adapted to induction. In this case
it is impossible to increase the power and the display shows [ U ]. This symbol disappears when an induction pan is put on the heating zone. If the pan is removed from the heating zone the operation is stopped. The display shows [
U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level set before. After use, switch the heat element off: do not let the pan detection [ U ] active.
After the switch off of a heating zone or the complete stop of the hob, the heating zones are still hot and the symbol [ H ] indicates this on the display. The symbol [ H ] disappears when the heating zones can be touched without danger. Do not touch the heating zones and do not put any heat sensitive objects on them, as long as the residual heat indicators are switched on. There are risks of burns and fire.
Power [ P ] and Super Power[
] grant a boost to the selected heating zone. When this function is activated, the heating zones work during 10 minutes at an ultra- high speed. This is meant to be used for heating up big quantities of water very quickly (for e.g. pasta).
Start up / Stop the Power: Action Control panel Display Start up the Power Slide to the end of the “SLIDER” [ P ] Or press directly on the end of the “SLIDER” Stop the Power Slide on the “SLIDER“ [ 9 ] to [ 0 ]
Start up / Stop Super Power: Action Control panel Display Start up Power Slide to the end of the “SLIDER” [ P ] Or press directly on the end of the “SLIDER” Start up Super Power Re-press key [ + ] [
and P ] Stop Super Power Slide on the “SLIDER“ [ P ] to [ 0 ] Stop Power Slide on the “SLIDER“ [ 9 ] to [ 0 ]
Power management: The whole cooking hob is equipped with a maximum potential. When the Power function is activated, the electronic system automatically orders to reduce the power level of another heating zone, in order to avoid exceeding the maximum potential. The display blinks [ 9 ] during a few seconds, then shows the maximum of power allowed :
Heating zone selected Other heating zone: (example: Booster level 9) [ P ] is displayed [ 9 ] goes to [ 6 ] or [ 8 ] depending the type of zone

Timer The timer can be used simultaneously with all the heating zones, and this with different time settings (from 1 to 999 minutes) for each heating zone.
Setting and modification of the cooking time : Action Control panel Display Select the power level slide on the “SLIDER“ [ 1 ] to [ P ] Select the timer Press simultaneously key [ - ] and [ + ] Timer display on of the timer until the desired display is on Decrease the time Press key [ - ] of the timer [ 60 ] to 59, 58... Increase the time Press key [ + ] of the timer Time increase After a few seconds, the [ min ] display stops blinking. The time is confirmed and the timer starts.
To stop the cooking time: Action Control panel Display Select the Timer Press simultaneously key [ - ] and [ + ] Timer display on of the timer until the desired display is on Stop the time Press key [ - ] of the timer [ 000 ] If several timers are activated, repeat the process.
Egg timer function: Egg timer is an independent function. It stops as soon as a heating zone starts working in the “Keep warm” Function (see below). When the hob is switched off, the timer continues until it has reached the selected time. Action Control panel Display Activate the hob press display [ 0/I ] [ 0 ] Select the Timer Press simultaneously key [ - ] and [ + ] [ 000 ] of the timer Decrease the time Press key [ - ] of the timer [ 60 ] to 59, 58... Increase the time Press key [ + ] of the timer Time increase After a few seconds, the [ min ] display stops blinking. The time is confirmed and the timer starts.
Automatic stop at the end of the cooking time: As soon as the selected cooking time has finished, the timer display is blinking [ 000 ] and a sound rings. To stop the sound and the blinking, press the key [ - ] and [ + ].

All the cooking zones are equipped with an automatic cooking device. The cooking zone starts at full power for a certain amount of time, then automatically reduces its power until it reaches the pre-selected power level.
Start-up:
Action Control panel Display
Power level selection slide on the “SLIDER“ to [ 7 ] [ 7 ] is blinking with [ A ] (for example « 7 ») and stay 3s
Switching off the automatic cooking:
Action Control panel Display
Power level selection slide on the “SLIDER“ [ 0 ] to [ 9 ]
This function temporarily puts an end to the hob’s entire cooking activity, and allows restarting with the same settings.
Engage stop&go press [ II ] [ II ] and control light on Stop stop&go press [ II ] “Slider” animated Press on the animated “slider” previous settings
After switching off the hob [ 0/I ], it is possible to recall the last settings.
cooking stages of all cooking zones (Booster) minutes and seconds of programmed cooking zone-related timers Keep warm function Automatic cooking The recall procedure is the following:
Press the key [ 0/I ] Then press [ II ] before the light stops blinking. The previous settings are activated again.
This function allows the cooking zones to reach and automatically maintain a temperature of 42, 70 or 94°C, this to avoid liquids flowing over and pans burning.
To start the function « Keep warm » :
Action Control panel Display
42°C to engage Press once on area under [
] 70°C to engage Press twice on area under [
] [ U ] and [
] 94°C to engage Press 3 times on area under [
] [ U ] and [
] To stop Slide on the “SLIDER“ [ 0 ] to [ 9 ] or press area under [
] [ U ] and [
] until [ 0 ] [ 0 ] The maximum duration of keeping warm is 2 hours.

This function allows the use of 2 cooking zones at the same time with the same features as a single cooking zone. Power function is not allowed. Action Control panel Display Activate the hob Press display [ 0/I ] [ 0 ] Activate the bridge Press simultaneously on area under
] of the 2 cooking zones Increase bridge Slide on the “SLIDER“ [ 1 ] to [ 9 ] which indicates the power Stop the bridge Press simultaneously on area under [
[ 0 ] and [
] [ 0 ] of the 2 cooking zones
To avoid modification of the setting of the cooking zones , particularly when cleaning, the control panel can be locked (with exception to the On/Off key [ 0/I ]). Action Control panel Display
Lock the hob Press [
] during 6s lock light on Unlock the hob Press [
] during 6s lock light off

aluminium with ferromagnetic bottom. Non-adapted materials : aluminium and stainless steel without ferromagnetic bottom,
copper, brass, glass, ceramic, porcelain. The manufacturers specify when their products are compatible induction. To check if pans are compatible:
Put a little water in a pan placed on an induction heating zone set at level [ 9 ].The water
will heat up in a few seconds when you are using the right induction pan. A magnet will stick on the bottom of an induction pan. Certain pans can make noise when they are placed on an induction cooking zone. This noise does not mean that there is something wrong with the appliance, nor does it influence its function.

The cooking zones will, up to a certain limit, automatically adapt to the diameter of the pan. Nevertheless, the bottom of the pans must have a minimum diameter according to the corresponding cooking zone. The pan should always be placed in the middle of the hob to obtain the best efficiency. The Wok pan must be adapted to the diameter and the shape of the ceramic glass cooking zone. Contact your seller to obtain a Wok pan with a 314 mm diameter.

(the values below are indicative)
1 to 2 Melting Reheating
Sauces, butter, chocolate, gelatine Dishes prepared beforehand 2 to 3 Simmering Defrosting
Rice, pudding, sugar syrup Dried vegetables, fish, frozen products 3 to 4 Steam Vegetables, fish, meat 4 to 5 Water Steamed potatoes, soups, pasta, fresh vegetables 6 to 7 Medium cooking Simmering
Meat, lever, eggs, sausages Goulash, roulade, tripe 7 to 8 Cooking Potatoes, fritters, wafers 9 Frying, roosting Boiling water
Steaks, omelettes, fried dishes Water P and
Frying, roosting Boiling water
Switch off the appliance before cleaning. Do not clean the hob when the glass is too hot: risk of burns.
Remove small spots with a damp cloth using washing-up liquid diluted in a little water. Then
rinse with cold water and dry the surface thoroughly. Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches
must be avoided at all costs. Never use steam driven or high-pressure appliances. Do not use objects that might scratch the ceramic glass. Ensure that the pan is dry and clean and that there is no dust on your ceramic hob or on the
pan. The use of rough saucepans will scratch the surface. Spillages of sugar, jam, jelly, etc. must be removed immediately to prevent a damaged
The hob or the cooking zone does not start:
The hob is badly connected to the electrical network. The safety fuse is cut off. The lock function is activated. The sensitive touch keys are covered with grease or water. An object is put on a sensitive touch key.
The control panel displays [ U ]:
There is no pan on the cooking zone. The pan is not compatible with induction. The pan’s bottom diameter is too small.

The control panel displays [ E ]:
The electronic system is defective. Disconnect and reconnect the hob. Call after sales service.
One or all cooking zone(s) are cut off:
The safety system functioned. This system works when you forgot to switch off the cooking zone. One or more sensitive touch keys are covered. The pan is empty and its bottom overheated. The hob also has an automatic reduction of the power level (see Booster function), and is
switched off automatically when there is a possibility of overheating.
The ventilation system is still working after switching off the hob:
This is not a failure, the fan continues to protect the electronic device. The fan stops automatically.
The automatic cooking system does not start:
The cooking zone is still hot [ H ]. The highest Booster level is set [ 9 ].
The control panel displays [ U ]:
See chapter “Keep warm“.
The control panel displays [ II ]:
See chapter “Stop&Go“.
The materials of packaging are ecological and recyclable. The electronic appliances are composed of precious metals. Ask your commune for
recycling possibilities.

Don't throw your appliance in the household refuse. Get in touch with the waste collection centre of your
commune that is adapted to the recycling of household appliances.

The installation is the exclusive responsibility of specialists. The user of this appliance is held to respect the legislation and the standards enforced in his home country. How to stick the gasket: The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. Its installation has to be done carefully, in accordance with the illustration below.

Stick the gasket (2) two millimetres from the external edge of the glass, after removing the protection sheet (3).
Fitting - installing:
The dimensions are:

Width Depth Width Depth Radius Width Depth Thickness 3762 350 490 386 526 8 380 520 4 3772 370 490 386 526 8 380 520 5.4 Ensure that there is a distance of 50 mm between the hob and the wall or sides. The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed
with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or device can be higher than the hob. The piece of furniture or the support in which the hob is to be fitted, as well as the edges of
furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C. The strips on the mural edges need to be heat-resistant. Do not install the hob above a non- ventilated oven or a dishwasher. To ensure good air circulation of the electronic device, maintain a space of 20 mm under
the bottom of the hob casing. If a drawer is placed under the work, avoid putting flammable objects in this drawer (e.g.
sprays) or non-heat-resistant objects. Materials which are often used to make worktops expand on contact with water. To protect
the cutout edge, apply a coat of varnish or special sealant. Particular care must be given when applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. The gasket guaranties a correct seal when used in conjunction with smooth worktop surfaces. The safety gap between the hob and the cooker hood placed above must respect the
indications of the hood manufacturer. Respect a distance of at least 760 mm if you do not have further instructions. The connection cable cannot be subjected to mechanical constraint (e.g. a drawer) after
construction.

The installation of this appliance and the connection to the electrical network should be
entrusted only to an electrician who is aware of the normative regulations and respects them scrupulously. The electrical parts should always be protected after the building-in. The necessary data of connection are on the stickers placed on the bottom of the
appliance. The appliance should be separated from the mains by using a multipolar circuit breaker.
The contact opening must be at least 3 mm. The electrical circuit must be separated from the mains by adapted devices, such as circuit
breakers, fuses or (differential) contactors. If the appliance is not fitted with an accessible plug, disconnecting means must be
incorporated in the fixed installation, in accordance with the installation regulations. The inlet hose must be positioned so that it does not touch any of the hot parts of the hob or
oven.
This appliance can only be connected to a network 230 V~ 50/60 Hz. You should always connect the earth wire. Respect the connection diagram. Use the connecting cable that is attached to the device. The green / yellow wire corresponds to the earth wire, the blue wire corresponds to the neutral wire and the brown wire correspond to the phase.
Mains Connection Cable diameter Cable Protection calibre
230V~ 50/60Hz 1 Phase + N 3 x 2,5 mm² H 05 VV - F H 05 RR - F 16 A *
* calculated with the simultaneous factor following the standard EN 60 335-2-6/1990
We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been
equipped with a faulty earth connection.



16572/0
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.