
Unpack all the materials.
The installation and connection of this appliance has to be done by approved specialists. The manufacturer cannot be held responsible for damage caused by building-in or connection errors.
This appliance can only be used when installed in a well-equipped kitchen unit with an adapted and approved work-surface.
This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use.
Remove all labels and self-adhesives from the ceramic glass.
Do not change or alter the appliance.
The cooking plate cannot be used freestanding nor can it be used as a work-surface.
The appliance must be grounded and connected in accordance with local standards.
Do not use any extension cord to connect it.
The appliance cannot be used above a dishwasher or a tumble-dryer: steam may damage the electronic appliances.
Switch the heating zones off after use.
Keep an eye on the food when using grease or oils: it may quickly ignite.
Be careful not to burn yourself while or after using the appliance.
Make sure no cable of any fixed or movable appliance comes in contact with the glass or the hot saucepan.
Magnetic objects (credit cards, floppy disks, calculators) should not be placed near the appliance when it is running.
Metallic objects such as knives, forks, spoons and lids should not be placed on the hob because they can get hot.
Use proper induction saucepans. In general, do not place any metallic object on the glass surface, except heat-resistant containers. If the appliance is switched on too soon or in case of residual heat, other materials could melt or ignite.
Never cover the appliance with a cloth or a protection sheet. It can get very hot and catch fire.
This appliance cannot be used by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are given supervision or instruction concerning the use of the appliance by someone responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

Raw pan bottoms or damaged saucepans (not enamelled cast iron pots) may damage the ceramic glass.
Sand or other abrasive materials may damage ceramic glass.
Avoid dropping objects, even little ones, on the vitroceramic.
Do not hit the edges of the glass with a saucepan.
Make sure that the ventilation system of the appliance works according to the manufacturer’s instructions.
Do not put or leave empty saucepans on the vitroceramic hobs.
Sugar, synthetic materials or aluminium sheets must not be exposed to the hot areas. These may cause cracks or other alterations of the vitroceramic glass by cooling: switch the appliance off and remove them immediately (be careful: do not burn yourself).
Never put any hot container on the control panel.
If a drawer is situated under the built-in appliance, make sure that the space between the content of the drawer and the inferior part of the appliance is large enough (2 cm). This is essential to guarantee correct ventilation.
Never put any inflammable object (e.g. spray) in the drawer situated under the vitroceramic hob. Any cutlery drawer must be heat-resistant.
In case of a malfunction, switch off the appliance and turn off the electrical supply.
If the ceramic glass is cracked or fissured, you must unplug the appliance and contact the after sales service.
Repair should be done by specialists. Do not open the appliance yourself.
For people with a pacemaker, the magnetic field could influence its function. We recommend you to retrieve further information from the retailer or the doctor.
Do not use aluminium or synthetic containers: they can melt on hot cooking zones.

Type Total Power Position of the heating zone
3753 2800 W 2 zones Ø145 mm
3754 5600 W 4 zones Ø145 mm
USE OF THE APPLIANCE
Timer display Bridge display
Timer display Power display Timer keys


“Slider” (front zone) Clean function
On/Off key Locking key Pause/Recal
Display Designation Description 0 Zero The heating zone is activated. 1…9 Booster level Selection of the cooking level. E Error message Electronic failure. H Residual heat The heating zone is hot. II Stop&Go The hob is in pause.

The cooling system is fully automatic. The cooling fan starts at a low speed when the calories generated by the electronic system reach a certain level. The ventilation starts its high speed level when the hob is intensively used. The cooling fan reduces its speed and stops automatically when the electronic circuit has cooled down enough. STARTING-UP AND APPLIANCE MANAGEMENT
Clean your hob with a damp cloth and then dry the surface thoroughly. Do not use detergent because this can create a blue-tinted colour on the glass surface.
An induction coil is located under each heating zone. When it is working, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone. Of course the pan has to be adapted:
All ferromagnetic pans are recommended (please verify it thanks to a little magnet): cast iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms…
Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic, stoneware,… The induction heating zone adapts automatically to the size of the pan. With a diameter that is too small, the pan doesn’t work. This diameter varies in function of the heating zone diameter. If the pan is not adapted to the induction hob the display will show [ U ].
Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. In case of normal use, press only one key at a time.
To select the power with the slider, slide your finger on the “SLIDER” zone. You can already have direct access if you put your finger directly on the chosen level.
Power selection zone “SLIDER” and

timer setting zone · “SLIDER“ Direct access

Start up / switch off the hob:
Action Control panel Display To start press key [ 0/I ] [ 0 ] To stop press key [ 0/I ] nothing or [ H ]
Start up / switch off a heating zone:
Action Control panel Display To set slide on the “SLIDER“ [ 1 ] to [ 9 ] (adjust the power) to the right or to the left To stop slide to [ 0 ] on “SLIDER“ [ 0 ] or [ H ] If no action is taken within 20 seconds, the electronics return in waiting position.
Example of power increase: The segments from the power display are turning on one by one until the required power level is reached.

Required power level Current power level
Example of power decrease: The segments from the power display are turning off one by one until the required power level is reached.

Required power level · Current power level

After the switch off of a heating zone or the complete stop of the hob, the heating zones are still hot and the symbol [ H ] indicates this on the display. The symbol [ H ] disappears when the heating zones may be touched without danger. Do not touch the heating zones and do not put any heat sensitive objects on them, as long as the residual heat indicators are switched on. There are risks of burns and fire.
The timer can be used simultaneously with all the heating zones, and this with different time settings (from 1 to 999 minutes) for each heating zone.
Setting and modification of the cooking time :
Action Control panel Display Select the power level slide on the “SLIDER“ [ 1 ] to [ 9 ] Select the timer Press simultaneously key [ - ] and [ + ] Timer display on from the timer until the desired display is on Decrease the time Press key [ - ] from the timer [ 60 ] to 59, 58... Increase the time Press key [ + ] from the timer Time increase
After a few seconds, the [ min ] display stops blinking. The time is confirmed and the timer starts.
To stop the cooking time:
Action Control panel Display Select the Timer Press simultaneously key [ - ] and [ + ] Timer display on from the timer until the desired display is on Stop the time Press key [ - ] from the timer [ 000 ] If several timers are activated, repeat the process.
Egg timer function:
Egg timer is an independent function. It stops as soon as a heating zone starts working. When the hob is switched off, the timer continues until it has reached the selected time. Action Control panel Display Activate the hob press display [0/I] [ 0 ] Select the Timer Press simultaneously key [ - ] and [ + ] [ 000 ] from the timer Decrease the time Press key [ - ] from the timer [ 60 ] to 59, 58... Increase the time Press key [ + ] from the timer Time increase
After a few seconds, the [ min ] display stops blinking. The time is confirmed and the timer starts.
Automatic stop at the end of the cooking time:
As soon as the selected cooking time has finished, the timer display is blinking [ 000 ] and a sound rings.
To stop the sound and the blinking, press the key [ - ] and [ + ].

This function brakes all the hob’s cooking activity temporarily and allows restarting with the same settings.
Start up/stop the stop&go function:
Action Control panel Display
Engage stop&go press [ II ] [ II ] and control light on Stop the stop&go press [ II ] “Slider” animated Press on the animated “slider” previous settings
After switching off the hob [0/I], it is possible to recall the last settings.
cooking stages of all cooking zones (Booster)
minutes and seconds of programmed cooking zone-related timers The recall procedure is the following:
Press the key [0/I]
Then press [ II ] before the light stops blinking. The previous settings are activated again.
This function allows the use of 2 cooking zones at the same time (left zones, middle zones, right zones) with the same features as a single cooking zone. Booster function is not allowed. Action Control panel Display Activate the hob Press display [ 0/I ] [ 0 ] Activate the bridge Press simultaneously on [
] of the 2 cooking zones Increase bridge Slide on the “SLIDER“ [ 1 ] to [ 9 ] which indicates the power Stop bridge Press simultaneously on [
] [ 0 ] and [
] [ 0 ] of the 2 cooking zones
To avoid modification of the setting of the cooking zones , particularly when cleaning, the control panel can be locked (with exception to the On/Off key [ 0/I ]). Action Control panel Display Lock the hob Press [
] during 6s lock light on Unlock the hob Press [
] during 6s lock light off

Special cooking function The special cooking function guarantees a satisfactory temperature to clean your teppan yaki (see Maintenance and cleaning chapter), to cook your fish or your meat Each zone has its own special cooking function. It is also possible to combine 2 cooking zones (bridge function), then to activate the clean function.
Start up/stop the clean function:
Action Control panel Display Activate the clean temperature press [
] one time [ ] is blinking Activate the temperature to cook fish press [
] two times [ ] is blinking Activate the temperature to cook meat press [
] three times [ ] is blinking
When the temperature is reached, the display becomes fixed.
Stop the function press [
] to [ 0 ] [ 0 ] or slide on the “SLIDER“ [ 0 ] à [ 9 ] COOKING ADVICES
Cooking levels Temperature (°C) 1 50 2 75 3 100 4 125 5 150 6 170 7 190 8 205 9 220 You can cook directly on the heating surface with or without fat (oil or grease). Avoid reaching the « smoking point » (too high temperature) when you are cooking with oil or fat. Food will lose its nutritive value. In order to conserve all the flavour and quality, be sure to adjust the right temperature in accordance with the type of cooking required.


Butter 130 / 4 150 Lard 170 / 6 200 Beef fat 180 / 6 210 Olive oil 180 / 6 200 Sunflower oil 200 / 7 220 Peanut oil 200 / 7 235 Coconut oil 200 / 7 240

Types of food Temperature (°C) Power Fish and seafood 170-180 6 Veal 160-180 6 Beef 200-210 8 Pork 180-210 7 Lamb 180-200 7 Poultry 160-180 6 Sausage 200 7-8 Fried egg 140 4-5 Pancake / omelette 140-160 5 Fruits 140-160 5 Vegetables 140-160 5 Simmering previously cooked rice 140-160 5 Simmering previously cooked pasta 140-160 5 MAINTENANCE AND CLEANING

Clean the control panel using a little washing-up liquid diluted in water or a recommended commercial vitroceramic product. Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be avoided at all costs. Dry the appliance with a clean rag. Spillages of sugar, jam, jelly, etc. must be removed immediately.
Cold cooking surface: Remove light marks with a damp cloth using washing up liquid diluted in a little water. Then rinse with cold water and dry the surface thoroughly with movements that follow the natural grooves of the cooking surface (no circular movements).
] becomes fixe (see paragraph " Special cooking function "). Put icicles on the cooking surface and remove light marks with a spatula and push them into the drain. Clean the drain with absorbent paper for example. Cold water can replace the icicles. Then dry the surface thoroughly with movements that follow the natural grooves of the cooking surface (no circular movements) with a clean rag. Some marks that come from acid naturally contained in food can be cleaned with lemon juice when the appliance is cold. Do not clean the hob if the glass is too hot: risk of burn. Highly corrosive or abrasive detergents and cleaning equipment likely to cause scratches must be avoided at all costs. Never use any steam-driven or pressure appliances.
] and wait to the [

The hob or the cooking zone does not start:
The hob is badly connected to the electrical network.
The safety fuse is cut off.
The lock function is activated.
The sensitive touch keys are covered with grease or water.
An object is put on a sensitive touch key.
The control panel displays [ E ]:
Disconnect and reconnect the hob.
Call after sales service.
One or all cooking zone(s) cut off:
The safety system functioned.
This system works when you forgot to switch off the cooking zone.
One or more sensitive touch keys are covered.
The pan is empty and its bottom overheated.
The hob also has an automatic reduction of Booster level and breaking Automatic overheating
The ventilation system is still working after switching the hob off:
This is not a failure, the fan continues to protect the electronic device.
The fan stops automatically.
The automatic cooking system does not start:
The cooking zone is still hot [ H ].
The highest Booster level is set [ 9 ].
The control panel displays [ II ]:
The materials of packaging are ecological and recyclable.
The electronic appliances are composed of precious metals. Ask your commune for recycling possibilities.

Don't throw your appliance in the household refuse
Get in touch with the waste collection centre of your commune that is adapted to the recycling of the household appliances.

The installation is the exclusive responsibility of specialists. The user of this appliance is held to respect the legislation and the standards enforced in his home country. How to stick the gasket:

Stick the gasket (2) two millimetres from the external edge of the glass, after removing the protection sheet (3).
Fitting - installing:
The dimensions are:

Type Width Depth Width Depth Radius Width Depth Thickness 3753 360 490 386 526 8 380 520 6 3754 560 490 586 526 8 580 520 6
Ensure that there is a distance of 50 mm between the hob and the wall or sides.
The hobs are classified as “Y” class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or device can be higher than the hob.
The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C.
The mural rods of edge must be heat-resisting.
Do not install the hob to the top of a non- ventilated oven or a dishwasher.
To ensure good air circulation of the electronic device, maintain a space of 20 mm under the bottom of the hob casing.
If a drawer is placed under the work, avoid putting flammable objects in this drawer (for example: sprays) or non-heat-resistant objects.
Materials which are often used to make worktops expand on contact with water. To protect the cutout edge, apply a coat of varnish or special sealant. Particular care must be given when applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces.
The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. Respect a distance of at least 760 mm if you do not have further instructions.
The connecting cable cannot be subjected to mechanical constraint (e.g. a drawer) after construction.

The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician who is aware of the normative regulations and who respects them scrupulously.
The electrical parts should always be protected after the building-in.
The necessary data of connection are on the stickers placed on the bottom of the appliance.
The appliance should be separated from the mains by using a multipolar circuit breaker. The contact opening must be at least 3 mm.
The electrical circuit must be separated from the mains by using adapted devices, such as circuit breakers, fuses or (differential) contactors.
If the appliance is not fitted with an accessible plug, disconnecting means must be incorporated in the fixed installation, in accordance with the installation regulations.
The inlet hose must be positioned so that it does not touch any of the hot parts of the hob or oven.
This appliance can only be connected to a network 230 V~ 50/60 Hz.
You should always connect the earth wire.
Respect the connection diagram. 3753 :
Use the connecting cable that is attached to the device. The green / yellow wire corresponds to the earth wire, the blue wire corresponds to the neutral one and the brown wire corresponds to the phase.
Mains Connection Cable diameter Cable Protection calibre
230V~ 50/60Hz 1 Phase + N 3 x 2,5 mm² H 05 VV - F H 05 RR - F 16 A *
* calculated with the simultaneous factor following the standard EN 60 335-2-6/1990

3754 :
The connection box is located below the hob. To open the cover, use a medium screwdriver. Place it in the slits and open the cover.
Mains Connection Cable diameter Cable Protection calibre
230V~ 50/60Hz 1 Phase + N 3 x 2.5 mm² H 05 VV - F H 05 RR - F 25 A *
400V~ 50/60Hz 2 Phases + N 4 x 1.5 mm² H 05 VV - F H 05 RR - F 16 A *
*calculé avec le coefficient de simultanéité suivant Norme EN 60 335-2-6/1990
Monophase 230V~1P+N :
Put a bridge between terminal 1 and 2 and between 4 and 5. Attach the earth to the terminal “earth”. Attach the neutral N to the terminal 4 or 5. Attach the phase L to the terminal 1 or 2.
Biphase 400V~2P+N :
Put a bridge between terminal 4 and 5. Attach the earth to the terminal “earth”. Attach the neutral N to the terminal 4 or 5. Attach the phase L1 to the terminal 1 and phase L2 to the terminal 2.
We cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been
equipped with a faulty earth connection.





16570/0
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.