



















Symbol END013-5 The following show the symbols used for the equipment. Be sure that you understand their meaning before use.
Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws, electric equipment and batteries and battery pack(s) that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Read instruction manual.
Do not expose to moisture.
Only for EU countries
Do not dispose of electric equipment or battery pack together with household waste material! In observance of the European Directives, on Waste Electric and
Intended use ENE014-1 The tool is intended for trimming hedges.
Ni-MH Li-ion

14. Do not operate the tool at no-load unnecessarily. 15. Immediately switch off the motor and remove the battery cartridge if the cutter should come into contact with a fence or other hard object. Check the cutter for damage, and if damaged repair immediately. 16. Before checking the cutter, taking care of faults, or removing material caught in the cutter, always switch off the trimmer and remove the battery cartridge. 17. Switch off the trimmer and remove the battery cartridge before doing any maintenance work. 18. When moving the hedge trimmer to another location, including during work, always remove the battery cartridge and put the blade cover on the cutter blades. Never carry or transport the trimmer with the cutter running. Never grasp the cutter with your hands. 19. Clean the hedge trimmer and especially the cutter after use, and before putting the trimmer into storage for extended periods. Lightly oil the cutter and put on the cover. The cover supplied with the unit can be hung on the wall, providing a safe and practical way to store the hedge trimmer. 20. Store the hedge trimmer with the cover on, in a dry room. Keep it out of reach of children. Never store the trimmer outdoors. 21. Never point the shear blades to yourself or others. 22. If the blades stop moving due to the stuck of foreign objects between the blades during operation, switch off the tool and remove the battery cartridge, and then remove the foreign objects using tools such as pliers. Removing the foreign objects by hand may cause an injury for the reason that the blades may move in reaction to removing the foreign objects. 23. Avoid dangerous environment. Don't use the tool in damp or wet locations or expose it to rain. Water entering the tool will increase the risk of electric shock. 24. Do not dispose of the battery(ies) in a fire. The cell may explode. Check with local codes for possible special disposal instructions. 25. Do not open or mutilate the battery(ies). Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed. 26. Do not charge battery in rain, or in wet locations. 27. Check the hedges and bushes for foreign objects, such as wire fences or hidden wiring before operating the tool.
Save all warnings and instructions for future reference.
1. Keep all parts of the body away from the cutter blade. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. A moment of inattention while operating the hedge trimmer may result in serious personal injury. 2. Carry the hedge trimmer by the handle with the cutter blade stopped. When transporting or storing the hedge trimmer always fit the cutting device cover. Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades. 3. Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring. Cutter blades contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 4. DANGER - Keep hands away from blade. Contact with blade will result in serious personal injury. 5. Do not use the hedge trimmer in the rain or in wet or very damp conditions. The electric motor is not waterproof. 6. First-time users should have an experienced hedge trimmer user show them how to use the trimmer. 7. The hedge trimmer must not be used by children or young persons under 18 years of age. Young persons over 16 years of age may be exempted from this restriction if they are undergoing training under the supervision of an expert. 8. Use the hedge trimmer only if you are in good physical condition. If you are tired, your attention will be reduced. Be especially careful at the end of a working day. Perform all work calmly and carefully. The user is responsible for all damages to third parties. 9. Never use the trimmer when under the influence of alcohol, drugs or medication. 10. Work gloves of stout leather are part of the basic equipment of the hedge trimmer and must always be worn when working with it. Also wear sturdy shoes with anti-skid soles. 11. Before starting work check to make sure that the trimmer is in good and safe working order. Ensure guards are fitted properly. The hedge trimmer must not be used unless fully assembled. 12. Make sure you have a secure footing before starting operation. 13. Hold the tool firmly when using the tool.
SAVE THESE INSTRUCTIONS.

causing fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it. 4. Charge the battery cartridge if you do not use it for a long period (more than six months).
1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. For commercial transports e.g. by third parties, forwarding agents, special requirement on packaging and labeling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required. Please also observe possibly more detailed national regulations. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. 11. When disposing the battery cartridge, remove it from the tool and dispose of it in a safe place. Follow your local regulations relating to disposal of battery. 12. Use the batteries only with the products specified by Makita. Installing the batteries to non-compliant products may result in a fire, excessive heat, explosion, or leak of electrolyte. 13. If the tool is not used for a long period of time, the battery must be removed from the tool.
Battery protection system (Lithium-ion battery with star marking) (Fig. 2) Lithium-ion batteries with a star marking are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: • Overloaded:
SAVE THESE INSTRUCTIONS.
The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on the tool and stop the application that caused the tool to

become overloaded. Then pull the switch trigger again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the switch trigger again. • Low battery voltage:
The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.
Indicating the remaining battery capacity (Only for battery cartridges with “B” at the end of the model number.) (Fig. 3) Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds.
capacity Lighted Off Blinking
battery.
have malfunctioned.
CAUTION: • Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. (Fig. 4) For your safety, this tool is equipped with a dual switching system. To turn on the tool, press the lock-off button and triggers A and B. Release either one of the two pressed triggers to turn off. The sequence of switching is unimportant as the tool only starts when both switches are activated.
Indication lamp (Fig. 5) Running the tool allows the indication lamp to show the battery cartridge capacity status. When the tool is also overloaded and has stopped during operation, the lamp lights up in red. Refer to the following table for the status and action to be taken for the indication lamp.

cartridge conditions. 010970
Press the chip receiver on the shear blades so that its slits overlap with the nuts on the shear blades. (Fig. 14) At this time, the chip receiver needs to be installed so that its hooks fit into grooves in the shear blade unit. (Fig. 15) To remove the chip receiver, press its lever on both sides so that the hooks are unlocked.
CAUTION: • Do not cut off dead trees or similar hard objects. Failure to do so may damage the tool. (Fig. 7) Hold the trimmer with both hands and pull the switch trigger A or B and then move it in front of your body. (Fig. 8) As a basic operation, tilt the blades towards the trimming direction and move it calmly and slowly at the speed rate of 3 - 4 seconds per meter. (Fig. 9) To cut a hedge top evenly, it helps to tie a string at the desired hedge height and to trim along it, using it as a reference line. (Fig. 10) Attaching the chip receiver (optional accessory) on the tool when trimming the hedge straight can avoid cut off leaves’ being thrown away. (Fig. 11) To cut a hedge side evenly, it helps to cut from the bottom upwards. (Fig. 12) Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job.
Cleaning the tool Clean out the tool by wiping off dust with a dry or soap- dipped rag.
Blade maintenance Smear the blade before and once per hour during operation using machine oil or the like.

OPTIONAL ACCESSORIES
Removing the shear blades (Fig. 16) Reverse the tool and loosen four screws and remove the under cover.
NOTE: • Be careful not to get your hands dirty as grease is applied in the shear blade driving area. (Fig. 17) Loosen four screws and remove the blades. Remove the washer and sponge from the shear blades and put them aside. They are required for the later installation. (Fig. 18) If the sleeves are still left in the holes of the gear, remove the gear and push the sleeves out of it with a screwdriver or the like.
Noise ENG905-1 The typical A-weighted noise level determined according to EN60745-2-15:
Model DUH481, DUH483, DUH521 Sound pressure level (LpA): 75 dB (A) Uncertainty (K): 2.5 dB (A) The noise level under working may exceed 80 dB (A).
Model DUH523 Sound pressure level (LpA): 77 dB (A) Uncertainty (K): 2.5 dB (A) The noise level under working may exceed 80 dB (A).
Installing the shear blade (Fig. 19) Remove the blade cover from the old shear blades and fit it onto the new ones to avoid contact with blades. (Fig. 20) Adjust the hole positions by turning the gear as illustrated. (Fig. 21 & 22) Apply some grease provided with the new shear blades as illustrated. (Fig. 23) Put the removed sponge in the same position as the old one. Make sure that the sleeves provided with the new shear blades are put on the pins of the blade. Place the new shear blades on the tool so that the pins fit in the holes of the gear. If the sleeves on the pins come off mistakenly, put them into the holes of the gear beforehand. (Fig. 24) Install the blade and tighten the four screws and put the removed washer in the same position as the old one. (Fig. 25) Install the under cover on the tool and tighten the four screws firmly.
Vibration ENG900-1 The vibration total value (tri-axial vector sum) determined according to EN60745-2-15:
Storage The hook hole in the tool bottom is convenient for hanging the tool from a nail or screw on the wall. (Fig. 26) Remove the battery cartridge and put the blade cover on the shear blades so that the blades are not exposed. Store the tool out of the reach of children carefully. Store the tool in the place not exposed to water and rain. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

EC Declaration of Conformity For European countries only The EC declaration of conformity is included as Annex A to this instruction manual.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.