DE
Makita logo
Offizielle Bedienungsanleitung

Makita DF331D

72 Seiten·13.1 MB·Akkubohrschrauber·PDF·ENJA
Makita DF331D
Inhaltsverzeichnis 26 Abschnitte IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25 · ENGLISH (Original instructions) · Intended use · Noise · … AnzeigenAusblenden
Page 1 of the Makita DF331D user manual — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25
Seite 1 · Zum Vergrößern klicken
Seite 1
Makita DF331D — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25 diagram (page 1)
Abb. 1 · IT Trapano avvitatore a batteria ISTRUZIONI PER L’US…

IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25

Makita DF331D — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25 diagram (page 1)
Abb. 2 · IT Trapano avvitatore a batteria ISTRUZIONI PER L’US…
Page 2 of the Makita DF331D user manual — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25
Seite 2 · Zum Vergrößern klicken
Seite 2
Makita DF331D — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25 diagram (page 2)
Abb. 3 · IT Trapano avvitatore a batteria ISTRUZIONI PER L’US…
Page 3 of the Makita DF331D user manual — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25
Seite 3 · Zum Vergrößern klicken
Seite 3
Makita DF331D — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25 diagram (page 3)
Abb. 4 · IT Trapano avvitatore a batteria ISTRUZIONI PER L’US…
Page 4 of the Makita DF331D user manual — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25
Seite 4 · Zum Vergrößern klicken
Seite 4
Page 4 of the Makita DF331D user manual — IT Trapano avvitatore a batteria ISTRUZIONI PER L’USO 25
Page 5 of the Makita DF331D user manual — EC Declaration of Conformity
Seite 5 · Zum Vergrößern klicken
Seite 5

ENGLISH (Original instructions)

Makita DF331D — ENGLISH (Original instructions) diagram (page 5)
Abb. 5 · ENGLISH (Original instructions)
Model:DF331DDF031D Drilling capacitiesSteel10 mm Wood21 mm Fastening capacitiesWood screw5.1 mm x 63 mm Machine screwM6 No load speedHigh (2)0 - 1,700 min-1 Low (1)0 - 450 min-1 Overall length189 mm157 mm Rated voltageD.C. 10.8 V Battery cartridgeBL1015, BL1020BBL1040BBL1015, BL1020BBL1040B Net weight1.1 kg1.3 kg0.94 kg1.1 kg
  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications and battery cartridge may differ from country to country.
  • Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Intended use

The tool is intended for drilling and screw driving in wood, metal and plastic.

Noise

The typical A-weighted noise level determined accord- ing to EN60745:

Model DF331D Sound pressure level (LpA) : 70 dB(A) or less Uncertainty (K) : 3 dB(A) The noise level under working may exceed 80 dB (A).

Model DF031D Sound pressure level (LpA) : 70 dB(A) or less Uncertainty (K) : 3 dB(A) The noise level under working may exceed 80 dB (A).

EC Declaration of Conformity

Vibration

For European countries only Makita declares that the following Machine(s): Designation of Machine: Cordless Driver Drill Model No./ Type: DF331D, DF031D Conforms to the following European Directives: 2006/42/EC They are manufactured in accordance with the following standard or standardized documents: EN60745 The technical file in accordance with 2006/42/EC is available from: Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium 25.2.2015

The vibration total value (tri-axial vector sum) deter- mined according to EN60745:

Model DF331D Work modedrilling into metal Vibration emission (a h,D ) : 2.5 m/s
2 or less Uncertainty (K)1.5 m/s
Model DF031D Work modedrilling into metal Vibration emission (a h,D ) : 2.5 m/s
2 or less Uncertainty (K)1.5 m/s

Yasushi Fukaya Director Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

Page 6 of the Makita DF331D user manual — Installing or removing battery cartridge
Seite 6 · Zum Vergrößern klicken
Seite 6

General power tool safety warnings

4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical atten- tion right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any con- ductive material. (2) Avoid storing battery cartridge in a con- tainer with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 °C (122 °F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. Follow your local regulations relating to dis- posal of battery. SAVE THESE INSTRUCTIONS. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery car- tridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room tem- perature at 10 °C - 40 °C (50 °F - 104 °F). Let a hot battery cartridge cool down before charging it.

Cordless driver drill safety warnings

1. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. 2. Hold power tool by insulated gripping sur- faces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. 3. Hold power tool by insulated gripping sur- faces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. 4. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Do not leave the tool running. Operate the tool only when hand-held. 8. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 9. Some material contains chemicals which may be toxic. Take caution to prevent dust inhala- tion and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Installing or removing battery cartridge

Important safety instructions for battery cartridge

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
[ Fig.11. Red indicator 2. Button 3. Battery cartridge]
Page 7 of the Makita DF331D user manual — Speed change
Seite 7 · Zum Vergrößern klicken
Seite 7

To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

Switch action

[ Fig.31. Switch trigger]
Makita DF331D — Switch action diagram (page 7)
Abb. 6 · Switch action

To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

Lighting up the front lamp

[ Fig.41. Lamp]

The tool is equipped with a battery protection system. This system automatically cuts off power to the motor to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on the tool and stop the application that caused the tool to become overloaded. Then pull the switch trigger again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the switch trigger again. Low battery voltage: The remaining battery capacity is too low and the tool will not operate. If you pull the switch trigger, the motor runs again but stops soon. In this situation, remove and recharge the battery.

Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out approximately 10 seconds after releasing the switch trigger.

Reversing switch action

[ Fig.51. Reversing switch lever]
Makita DF331D — Reversing switch action diagram (page 7)
Abb. 7 · Reversing switch action

Indicating the remaining battery capacity

Only for battery cartridges with "B" at the end of the model number [Fig.2: 1. Indicator lamps 2. Check button]

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for coun- terclockwise rotation. When the reversing switch lever is in the neutral posi- tion, the switch trigger cannot be pulled.

Press the check button on the battery cartridge to indi- cate the remaining battery capacity. The indicator lamps light up for few seconds.

Makita DF331D — Indicating the remaining battery capacity diagram (page 7)
Abb. 8 · Indicating the remaining battery capacity
Indicator lampsRemaining capacity LightedOff 75% to 100% 50% to 75% 25% to 50% 0% to 25%

Speed change

[ Fig.61. Speed change lever]
Makita DF331D — Speed change diagram (page 7)
Abb. 9 · Speed change
Page 8 of the Makita DF331D user manual — Installing or removing driver bit/ socket bit
Seite 8 · Zum Vergrößern klicken
Seite 8
Position of speed change leverSpeedTorqueApplicable operation 1LowHighHeavy loading operation 2HighLowLight loading operation
Makita DF331D — Installing or removing driver bit/ socket bit diagram (page 8)
Abb. 10 · Installing or removing driver bit/ socket bit

To change the speed, switch off the tool first. Select the "2" side for high speed or "1" for low speed but high torque. Be sure that the speed change lever is set to the correct position before operation. If the tool speed is coming down extremely during the operation with "2", slide the lever to the "1" and restart the operation.

[ Fig.71. Adjusting ring 2. Graduation 3. Arrow]

The fastening torque can be adjusted in 19 steps by turning the adjusting ring. Align the graduations with the arrow on the tool body. You can get the minimum fastening torque at 1 and maximum torque at marking. The clutch will slip at various torque levels when set at the number 1 to 18. The clutch does not work at the marking. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. The following shows the rough guide of the relationship between the screw size and graduation.

Makita DF331D — Installing or removing driver bit/ socket bit diagram (page 8)
Abb. 11 · Installing or removing driver bit/ socket bit

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Makita DF331D — Installing or removing driver bit/ socket bit diagram (page 8)
Abb. 12 · Installing or removing driver bit/ socket bit

Installing or removing driver bit/ socket bit

For Model DF031D (optional accessory) [Fig.9]

Use only driver bit/socket bit that has inserting portion shown in the figure. Do not use any other driver bit/ socket bit. For tool with shallow driver bit hole

For Model DF331D (optional accessory) [Fig.8: 1. Sleeve 2. Close 3. Open]

Use only these type of driver bit. Follow the procedure 1. (Note) Bit-piece is not necessary.

Turn the sleeve counterclockwise to open the chuck jaws. Place the driver bit/drill bit in the chuck as far as it will go. Turn the sleeve clockwise to tighten the chuck. To remove the driver bit/drill bit, turn the sleeve counterclockwise.

For tool with deep driver bit hole

A=17mm B=14mmTo install these types of driver bits, follow the procedure 1. A=12mm B=9mmTo install these types of driver bits, follow the procedure 2. (Note) Bit-piece is necessary for installing the bit.
Makita DF331D — Installing or removing driver bit/ socket bit diagram (page 8)
Abb. 13 · Installing or removing driver bit/ socket bit
1. To install the driver bit, pull the sleeve in the direction of the arrow and insert the driver bit into the sleeve as far as it will go. Then release the sleeve to secure the driver bit. [ Fig.10: 1. Driver bit 2. Sleeve]
2. To install the driver bit, pull the sleeve in the direction of the arrow and insert the bit-piece and driver bit into the sleeve as far as it will go. The bit-piece should be inserted into the sleeve with its pointed end facing in. Then release the sleeve to secure the driver bit. [ Fig.11: 1. Driver bit 2. Bit-piece 3. Sleeve]

A=12mm B=9mm

Page 9 of the Makita DF331D user manual — Screwdriving operation
Seite 9 · Zum Vergrößern klicken
Seite 9

To remove the driver bit, pull the sleeve in the direction of the arrow and pull the driver bit out.

Drilling operation

First, turn the adjusting ring so that the pointer points to the marking. Then proceed as follows.

Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the drill bit into the workpiece.

Installing hook

Drilling in metal To prevent the drill bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the drill bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The excep- tions are iron and brass which should be drilled dry.

[ Fig.121. Groove 2. Hook 3. Screw]

The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, loosen the screw and then take it out.

Installing driver bit holder

Optional accessory [ Fig.131. Driver bit holder 2. Driver bit]

Fit the driver bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the driver bit holders. Driver bits 45 mm-long can be kept there.

OPERATION

CAUTION: Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part can- not be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

Using the tool as a hand screwdriver

Hold the tool firmly with one hand on the grip and the other hand on the bottom of the battery cartridge to control the twisting action. [Fig.14]

Switch off the tool. Move the reversing switch lever to the neutral position. Turn the adjusting ring so that the arrow points to the marking. Turn the tool.

Screwdriving operation

Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger as soon as the clutch cuts in.

Page 10 of the Makita DF331D user manual — OPTIONAL ACCESSORIES
Seite 10 · Zum Vergrößern klicken
Seite 10

Using holster

1. Thread a waist belt or similar through holster holder. [ Fig.16: 1. Holster holder 2. Waist belt]
2. Put the tool in the holster and lock it with the holster button. [ Fig.17 ]

You can keep two driver bits at the front of the holster.

MAINTENANCE

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

  • If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
  • Drill bits
  • Driver bits
  • Socket bits
  • Bit piece
  • Driver bit holder
  • Holster
  • Plastic carrying case
  • Hook
  • Makita genuine battery and charger

Optional accessory

Frage zu Makita DF331D stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita DF331D

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita DF331D PDF-Anleitung

72 Seiten·13.1 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…