DE
Makita logo
Offizielle Bedienungsanleitung

Makita DDF459

52 Seiten·1.2 MB·Akkubohrschrauber·PDF·ENJA
Makita DDF459
Inhaltsverzeichnis 18 Abschnitte P Furadeira / Parafusadeira a Bateria Manual de instruções · ENGLISH (Original instructions) · Explanation of general view · SPECIFICATIONS · … AnzeigenAusblenden
Page 1 of the Makita DDF459 user manual — P Furadeira / Parafusadeira a Bateria Manual de instruções
Seite 1 · Zum Vergrößern klicken
Seite 1
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 1)
Abb. 1 · P Furadeira / Parafusadeira a Bateria Manual de inst…

P Furadeira / Parafusadeira a Bateria Manual de instruções

Page 2 of the Makita DDF459 user manual — P Furadeira / Parafusadeira a Bateria Manual de instruções
Seite 2 · Zum Vergrößern klicken
Seite 2
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 2)
Abb. 2 · P Furadeira / Parafusadeira a Bateria Manual de inst…
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 2)
Abb. 3 · P Furadeira / Parafusadeira a Bateria Manual de inst…
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 2)
Abb. 4 · P Furadeira / Parafusadeira a Bateria Manual de inst…
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 2)
Abb. 5 · P Furadeira / Parafusadeira a Bateria Manual de inst…
Show 4 more labels / short text on this page
012970 012128 · 012971 012972 · 012973 012975 · 012974 012976
Page 3 of the Makita DDF459 user manual — P Furadeira / Parafusadeira a Bateria Manual de instruções
Seite 3 · Zum Vergrößern klicken
Seite 3
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 3)
Abb. 6 · P Furadeira / Parafusadeira a Bateria Manual de inst…
Makita DDF459 — P Furadeira / Parafusadeira a Bateria Manual de instruções diagram (page 3)
Abb. 7 · P Furadeira / Parafusadeira a Bateria Manual de inst…

012977 012798 · 012979 012978

Page 4 of the Makita DDF459 user manual — GEB088-1
Seite 4 · Zum Vergrößern klicken
Seite 4

ENGLISH (Original instructions)

Explanation of general view

1 Red indicator 2 Button 3 Battery cartridge 4 Star marking 5 Switch trigger 6 Lamp

7 Reversing switch lever 8 Speed change lever 9 Adjusting ring 10 Graduation 11 Arrow 12 Sleeve

13 Groove 14 Hook 15 Screw 16 Bit holder 17 Bit 18 Vent

SPECIFICATIONS

ModelDDF459 CapacitiesSteel13 mm Wood38 mm Wood screw6 mm x 75 mm Machine screwM6 No load speed (min–1)High (2)0 – 1,500 Low (1)0 – 400 Overall length179 mm Rated voltageD.C. 18 V Battery cartridgeBL1815 / BL1815N / BL1820BL1830 / BL1840 / BL1850 Net weight1.4 kg1.7 kg
  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications and battery cartridge may differ from country to country.
  • Weight, with battery cartridge, according to EPTA-Procedure 01/2003

3. Hold power tool by insulated gripping surfaces, when performing an operation where the fas- tener may contact hidden wiring. Fasteners con- tacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 4. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Do not leave the tool running. Operate the tool only when hand-held. 8. Do not touch the drill bit or the workpiece imme- diately after operation; they may be extremely hot and could burn your skin. 9. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

ENE034-1 Intended use The tool is intended for drilling and screw driving in wood, metal and plastic.

GEA010-1 General Power Tool Safety Warnings

SAVE THESE INSTRUCTIONS.

GEB088-1

CORDLESS DRIVER DRILL SAFETY WARNINGS 1. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury. 2. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Page 5 of the Makita DDF459 user manual — Installing or removing battery cartridge (Fig. 1)
Seite 5 · Zum Vergrößern klicken
Seite 5

ENC007-8

  • Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instruc- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using bat- tery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conduc- tive material. (2) Avoid storing battery cartridge in a con- tainer with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain.

To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

  • CAUTION:
  • Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.
  • Battery protection system The tool and battery are equipped with a protection system. This system automatically cuts off power to the tool to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions:
  • Overloaded: The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, release the switch trigger on the tool and stop the application that caused the tool to become overloaded. Then pull the switch trigger again to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before pulling the switch trigger again.
  • Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.

A battery short can cause a large current flow, overheating, possible burns and even a break- down. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. Follow your local regulations relating to disposal of battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the bat- tery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room tempera- ture at 10°C – 40°C (50°F – 104°F). Let a hot bat- tery cartridge cool down before charging it. 4. Charge the battery cartridge once in every six months if you do not use it for a long period of time.

Switch action (Fig. 3)

To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

FUNCTIONAL DESCRIPTION

Lighting up the lamp (Fig. 4)

Installing or removing battery cartridge (Fig. 1)

Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The lamp goes out just after releasing the trigger.

Page 6 of the Makita DDF459 user manual — ASSEMBLY
Seite 6 · Zum Vergrößern klicken
Seite 6

Installing the bit holder (Optional accessory) (Fig. 10) Fit the bit holder into the protrusion at the tool foot on either right or left side and secure it with a screw. When not using the driver bit, keep it in the bit holders. Bits 45 mm long can be kept there.

Reversing switch action (Fig. 5)

  • CAUTION:
  • Always check the direction of rotation before operation.
  • Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
  • When not operating the tool, always set the reversing switch lever to the neutral position.

OPERATION

CAUTION: • Always insert the battery cartridge all the way until it locks in place. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counter- clockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

Hold the tool firmly with one hand on the grip and the other hand on the bottom of the battery cartridge to con- trol the twisting action.

Speed change (Fig. 6)

  • CAUTION:
  • Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and “2” side, the tool may be damaged.
  • Do not use the speed change lever while the tool is running. The tool may be damaged.

Screwdriving operation (Fig. 12) First, turn the action mode changing ring so that the arrow on the tool body points to the marking. Adjust the adjusting ring to the proper torque level for your work. Then proceed as follows. Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the switch trigger as soon as the clutch cuts in.

To change the speed, first switch off the tool and then slide the speed change lever to the “2” side for high speed or “1” side for low speed. Be sure that the speed change lever is set to the correct position before opera- tion. Use the right speed for your job.

Adjusting the fastening torque (Fig. 7) The fastening torque can be adjusted in 17 steps by turn- ing the adjusting ring so that its graduations are aligned with the pointer on the tool body. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the m marking is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. The clutch is designed not to slip at the m marking. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.

Drilling operation First, turn the adjusting ring so that the pointer points to the m marking. Then proceed as follows.

  • CAUTION:
  • Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool.
  • There is a tremendous force exerted on the tool/bit at the time of hole break through. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
  • A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly.
  • Always secure small workpieces in a vise or with a similar hold-down device.
  • If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.
  • Do not pull the switch trigger repeatedly when the motor is locked. It may damage the tool.

ASSEMBLY

Installing or removing the driver bit or drill bit (Fig. 8) Turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Turn the sleeve clockwise to tighten the chuck. To remove the bit, turn the sleeve counterclockwise.

Installing the hook (Fig. 9) The hook is convenient for temporarily hanging the tool. This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool hous- ing on either side and then secure it with a screw. To remove, loosen the screw and then take it out.

Page 7 of the Makita DDF459 user manual — OPTIONAL ACCESSORIES
Seite 7 · Zum Vergrößern klicken
Seite 7

Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting to make a hole, make an indentation with a center-punch and ham- mer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The excep- tions are iron and brass which should be drilled dry.

  • ENG901-1
  • The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
  • The declared vibration emission value may also be used in a preliminary assessment of exposure.
  • WARNING:
  • The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
  • Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

MAINTENANCE

  • CAUTION:
  • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
  • Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

ENH101-17 For European countries only

EC Declaration of Conformity

Makita declares that the following Machine(s): Designation of Machine: Cordless Driver Drill Model No./ Type: DDF459 Conforms to the following European Directives:

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be per- formed by Makita Authorized Service Centers, always using Makita replacement parts.

2006/42/EC They are manufactured in accordance with the following Standard or standardized documents:

OPTIONAL ACCESSORIES

EN60745 The Technical file in accordance with 2006/42/EC is available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

31.12.2013

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

  • Drill bits
  • Screw bits
  • Socket bit
  • Safety goggles
  • Makita genuine battery and charger
  • Hook
  • Bit holder

Director Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

ENG905-1 Noise The typical A-weighted noise level determined according to EN60745:

Sound pressure level (LpA): 72 dB (A) Uncertainty (K): 3 dB (A) The noise level under working may exceed 80 dB (A).

ENG900-1 Vibration The vibration total value (tri-axial vector sum) determined according to EN60745:

Work mode: drilling into metal Vibration emission (ah, D): 2.5 m/s2 or less Uncertainty (K): 1.5 m/s2

Yasushi Fukaya · Wear ear protection

Frage zu Makita DDF459 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita DDF459

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita DDF459 PDF-Anleitung

52 Seiten·1.2 MB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…