Benutzeranleitung / Produktwartung FID 46 des Produzenten Body Solid
Zur Seite of 46
by Bo d y - S o lid ® FID46 Flat/Incline/Decline Bench OWNER’ S MANUAL & FID46 Assembly Instructions T able of Contents Safety Instructions . . . . . . . . . . . . . . . . . p. 3 Assembly Instructions . . . . . . . . . . . . p .3-10 W arning, Safety & Maintenance .
1 Important Safety Instructions Before beginning any fitness pr ogram, you should obtain a complete physical examination from your physician. Il est conseille de subir un examen medical complet avant d’entrepr endre tout programme d’exercise. Si vous avez des etourdissements ou des faiblesses, arr etez les exercices immediatement.
2 Assembly Instructions Y ou must review and follow the instructions in this Owner’ s Manual. If you do not assemble and use the PowerLIFT FID Bench according to these guidelines, you could void the Body-Solid warranty . Assembly of the PowerLIFT FID Bench takes professional installers about 45 minutes to complete.
STEP 1 A. Attach front leg (A) to mainframe (B) with brace plate (D) as shown using: two 29 (square neck carriage bolt 10mm x 95mm) two 36 (flat washer 10mm) two 32 (nylon lock nut 10mm) B.
4 STEP 1.
STEP 2 A. See Note 1. Install 210mm (8 1/4”) long bolt (21) thru left side of seat brace (H), and then seat pivot (G), and then thru right side seat brace (H), using the center hole on each seat brace as shown. Use the following: one 21 (hex bolt 10mm x 210mm partial thread) two 36 (flat washer 10mm) one 32 (nylon lock nut 10mm) B.
STEP 2 6.
STEP 3 A. See Note 1. Install all four handles (K, L, M, and N) on to seat braces (H) and back braces (J). Install as shown and described using: eight 26 (hex bolt 10mm x 40mm full thread) sixteen 36 (flat washer 10mm) eight 32 (nylon lock nut 10mm) B.
STEP 3 8.
STEP 4 A. Slide main post (T) into main post receiver of mainframe (B). Lock in place with adjustment pin (13). Note: this leg developer main post is adjustable to properly align the pivot point with your knee joint and accommodate all size users. B. Align pivot arm (R) with receiver of main post (T).
10 STEP 4.
11 W arning , Safety & Maintenance Be sure that all users car efully read and understand all warning, safety and maintenance labels on the bench before each use. Failur e to do so may cause serious injury . It is imperative that you retain this Owner’ s Manual and be sure all warning labels are legible and intact.
Safety Guidelines Successful resistance training pr ograms have one prominent feature in common...safety . Resistance training has some inherent dangers, as do all physical activities.
PHRASES, TERMS, TIPS & GUIDELINES AEROBIC Exercise that primarily uses oxygen to burn fuel at low to moderate levels of intensity . Running and jogging are examples of aer obic exercise. ANAEROBIC Exercise that primarily uses the body’ s stored fuel for energy .
PHRASES, TERMS, TIPS & GUIDELINES POWER Power is the rate of perfor ming work. Power during a r epetition is defined as the weight lifted times the vertical distance the weight is lifted divided by the time to complete the repetition.
NUTRITION Good nutrition is a diet in which foods are eaten in proper quantities and with the needed distribution of nutrients to maintain good health.
EXERCISE PRESCRIPTION Sets Sets are defined as a combination of any number of r eps of one exercise. The number of sets used in a workout is directly r elated to training results. T ypically , two to three sets are used by intermediate and advanced lifters to achieve optimum gains in strength.
TRAINING TIPS FOR BEGINNER’S As a beginner , one of the most common mistakes is doing too much. Because beginners often make good gains quickly , many fall into the trap of thinking that more is better . This may be true later in the training equation, but not for the novice.
COMMON TRAINING MIST AKES 1. Lack of Adequate W arm-Up and Inadequate Flexibility A warmed muscle is a more flexible muscle that’ s better able to lift heavier weights and work in a full range of motion. Those warmed muscles also greatly reduce your chance of training injuries.
SE TTING UP YOUR PERSONAL PROGRAM It is important to first establish specific and realistic goals. Y ou should deter mine your long term goal and then set a series of short ter m goals that will help you attain your long term goal.
DE TERMINE YOUR TRAINING ME THOD There ar e three basic types of weight training methods: 1. T raining for muscular endurance and definition 2. T raining for strength 3. T raining for power and muscle mass Y ou should select a training method that reflects both your pr esent fitness level and your long term goals.
EX E R C I S E TI P S CHEST This powerful muscle group is the cornerstone of a well-developed upper body . T o most thoroughly work your pecs, include both pressing and fly movements and vary the angle of the bench from decline to flat to incline.
ANA TOMY CHART 22 FRONT VIEW Note: These illustrations depicting exaggerated musculature ar e not in the textbook anatomical position. As such, they are inexact for medical purposes but are useful for a general understanding.
SHOR T -TERM GOALS Date Set Date Accomplished Goal Reward ** Date Set Date Accomplished Goal Reward ** Date Set Date Accomplished Goal Reward ** LONG-TERM GOALS Goal Reward! * Make several copies of this page to keep track of your goals and accomplishments.
WEIGHT TRAINING EXERCISE L O G BEGINNER’S SAMPLE WORKOUT ROUTINE Keep track of your changes and impr ovements. It’ s a great motivational tool!* S= Sets R= Repetitions per set W= W eight used * Make several copies of this page to keep track of your progress.
WEIGHT TRAINING EXERCISE L O G SAMPLE WORKOUT ROUTINE WHEN TRAINING FOR STRENGTH Keep track of your changes and impr ovements. It’ s a great motivational tool!* S= Sets R= Repetitions per set W= W eight used * Make several copies of this page to keep track of your progress.
WEIGHT TRAINING EXERCISE L O G INTERMEDIA TE AND ADV ANCED LIFTERS... Design your personal str ength training pr ogram. Keep track of your changes and impr ovements. It’ s a great motivational tool!* S= Sets R= Repetitions per set W= W eight used * Make several copies of this page to keep track of your progress.
STRE TCHING & FLEXIBILIT Y Flexibility is an important component of physical fitness and needs to be addressed in a resistance training pr ogram. The two main purposes for stretching are injury prevention and a faster rate of r ecover y from exer cise.
UPPER BACK Cross Arm in Front of Chest MUSCLE(S) AFFECTED: latissimus dorsi and teres major 1. Stand or sit with the right ar m slightly flexed (15° to 30°) and adducted across the chest. 2. Grasp the upper ar m just above the elbow , placing the left hand on the posterior side of the upper arm.
LOWER BACK Semi-Leg Straddle MUSCLE(S) AFFECTED: spinal erectors 1. Sitting, knees flexed 30 to 50 degrees, let the legs totally relax. 2. Point the knees outward; the lateral side of the knees may or may not touch the floor . 3. Lean forward from waist and r each forward with extended arms.
SHOULDER Seated Lean-Back MUSCLE(S) AFFECTED: deltoids and pectoralis major 1. Sitting with legs straight and ar ms extended, place palms on floor about 12 inches behind hips. 2. Point fingers away (backward) from body . 3. Slide hands backward and lean backward.
NECK Look Right and Left MUSCLE(S) AFFECTED: sternocleidomastoid 1. Stand or sit with head and neck upright. 2. T ur n head to the right using a submaximal concentric contraction. Hold for 10 seconds. 3. T ur n head to the left using a submaximal concentric contraction.
SIDES Side Bend with Straight Arms MUSCLE(S) AFFECTED: external oblique, latissimus dorsi and serratus anterior 1. Stand with feet 14 to 16 inches apar t. 2. Interlace the fingers with palms facing each other . 3. Reach upward with straight arms. 4. Keeping ar ms straight, lean fr om waist to left side.
Stretching the hamstrings with emphasis on insertion of the hamstrings and calves. Stretching the hamstrings with emphasis on the middle portion. Stretching the hamstrings with emphasis on the upper portion. ANTERIOR OF THIGH AND HIP FLEXOR Kneeling Quadriceps Stretch MUSCLE(S) AFFECTED: quadriceps 1.
Stretching the hamstrings with emphasis on insertion of the hamstrings and calves Stretching the hamstrings with emphasis on the middle portion Stretching the hamstrings with emphasis on the upper portion POSTERIOR OF THIGH Semistraddle (Figure Four) MUSCLE(S) AFFECTED: gastrocnemius, hamstrings and spinal erectors 1.
Stretching the hamstrings and groin with emphasis on insertion of the hamstrings and calves Stretching the hamstrings and groin with emphasis on the middle portion Stretching the hamstrings and groin .
GROIN Butterfly MUSCLE(S) AFFECTED: adductors and sartorius 1. Sitting with the upper body nearly ver tical and legs straight, flex both knees as the soles of the feet come together . 2. Pull feet toward body . 3. Place hands on feet and elbows on legs.
Stretching the calves standing on a step Preparing to stretch the achilles tendon by slightly bending the knee POSTERIOR OF LOWER LEG Step Stretch MUSCLE(S) AFFECTED: gastrocnemius and soleus; also, achilles tendon 1. Have ready a step or board 3 to 4 inches high.
Elliptical Machine #ETX4.0 Decathlon T readmill #ETDEC BUILD THE UL TIMA T E FITNESS CENTER with Cardio from 100 % Covered LIFE TIME W ARRANT Y Accessories Olympic Wei ght T ree #WT46 Strength T raini.
NOTES 39.
NOTES 40.
Reference Drawings 41 FID46 Flat/Incline/Decline Bench.
FID46 Hardware (continued) (shown in actual size) Inch mm 42 Key # spring lock washer 10mm QTY . 3 35 Key # flat washer 10mm QTY . 34 36 Key # flat washer 10mm x 30mm QTY . 3 34 Key # nylon lock nut 10mm QTY . 19 32 Key # hex bolt 8mm x 60mm partial thread QTY .
FID46 Hardware Inch mm 43 Key # hex bolt 10mm x 40mm full thread QTY . 8 26 Key # round allen head 10mm x 20mm full thread bolt QTY . 3 28 Key # square neck carriage bolt 10mm x 95mm QTY . 4 29 Key # hex bolt 10mm x 60mm partial thread QTY . 2 25 Key # hex bolt 10mm x 80mm partial thread QTY .
44 FID46 Mainframe Parts List FID46 Labels/Decals List FID46 Pads List Part numbers are requir ed when ordering parts. KEY# QTY P ART# DESCRIPTION A 1 FID46FL-A FRONT LEG B 1 FID46MF-B MAINFRAME C 1 F.
EXPLODED VIEW DIAGRAM Body-Solid FID46 Flat/Incline/Decline Bench © Copyright 2003. Body-Solid. All rights reser ved. Body-Solid reserves the right to change design and specifications when we feel it will improve the product. Body-Solid machines maintain several patented and patent pending features and designs.
Ein wichtiger Punkt beim Kauf des Geräts Body Solid FID 46 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Body Solid FID 46 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Body Solid FID 46 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Body Solid FID 46 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Body Solid FID 46 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Body Solid FID 46 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Body Solid FID 46 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Body Solid FID 46. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Body Solid FID 46 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
