Benutzeranleitung / Produktwartung RP des Produzenten Zebra Technologies
Zur Seite of 22
Document: Chargers_F .pdf Rev . F , July , 2002 Mobile Printer Chargers MP Series, RP Series Encore Series, Cameo Series, QL Series User’ s Manual.
Proprietary Statement This manual contains proprietary information of Zebra T echnologies Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein.
Contents Introduction ................................................................................... 4 MP and RP Series Printers ............................................................................ 4 Cameo and Encore Series ..............
UMAN-Charge 4 Introduction This manual covers the use of all chargers currently of- fered by Zebra for use with MP , RP , Encore, Cameo and QL series mobile printers.
5 UMAN-Charge F a u lt F a st C h a rg e F u l F u ll C h a rg e F a u lt F a s t C h arg e R e a d y continued on next page UCLI72-4 Quad Charger Description The UCLI72-4 Quad Charger is designed to charge up to four Lithium-Ion (LIon) QL series Mobile Printer battery packs simultaneously .
UMAN-Charge 6 F u l l C h a r g e F a u l t F a s t C h a r g e R e a d y Note the orientation of the battery pack. Slide the battery pack into the charging bay until it stops. Then rock the battery pack back until it snaps into place. The amber indicator directly under the battery being charged will turn on if the battery is properly inserted.
7 UMAN-Charge F a u l t F a s t C h a r g e F a u l t F a s t C h a r g e F a u l t F a s t C h a r g e R e a d y P o w e r F u l l C h a r g e R e a d y F u l l C h a r g e R e a d y F u l l C h a r g e Refer to the chart below for a quick reference: Amber Green Battery Status On Off Charging On Flashing O.
UMAN-Charge 8 Charging Times QL220/320 QL 420 (A T16004-1) (A T16293-1) 80% charge 1.25 hrs 2.5 Hrs. Full Charge 2.5 hrs 5 hrs. These times are for completely discharged batteries. Bat- tery packs which are still partially charged will take less time.
9 UMAN-Charge continued on next page UCN72-4 Quad Charger Description The UCN72-4 Quad Charger is designed to charge up to four NiMH Encore and/or Cameo series batteries simulta- neously . Battery packs may be charged externally or while plugged into the printer .
UMAN-Charge 10 the battery pack to be charged. The charge indicator near the cable will either light steadily , or start to blink. On a fully charged battery , the indicator will go out after a few minutes, indicating a fully charged condition.
11 UMAN-Charge NCxx04 Series Quad Charger/Conditioners Description NC series Quad Chargers sequentially charge and/or condition up to 4 batteries. Charge time is approximately one hour per battery depending on battery’s state of charge. Condition cycle times vary with both the battery’s state of charge and with each model.
UMAN-Charge 12 Conditioning Battery Packs In order to extend battery life, battery packs should be conditioned periodically . The NC series Quad Chargers are equipped with a "Condition" mode, which fully discharges a battery pack followed by a full charge cycle.
13 UMAN-Charge The communications port should only be used by factory authorized personnel. NCxx04 Part Numbers Part Number* Used On Charge Method DC12127-1x MP5020/22 Battery Drop-In DC12255-1x MP503.
UMAN-Charge 14 Charging Tr i c kle Charging F ault Condition LI72 W all Charger Description The LI72 is a wall mounted fast charger with universal 1 10 to 230, 50-60 Hz. V AC input. Multiple A.C. plug configura- tions comply with most interna- tional standards.
15 UMAN-Charge Do not attempt to charge batteries with the LI72 while printing. Attempting to print while charging can result in improp- erly charged batteries. LI72 Models Model number Country of use V .A.C. A T15759-1 U.S. & Japan 1 10 A T15759-2 U.
UMAN-Charge 16 Charging Tr i c kle Charging T emperature too high/low UCN72 W all Charger Description The UCN72 is a wall mounted fast charger with universal 1 10 to 230, 50-60 Hz. V AC input. Multiple A.C. plug configu- rations comply with most interna- tional standards.
17 UMAN-Charge UCN72 Models Model number Country of use V .A.C. A T15244-1 U.S. & Japan 1 10 A T15244-2 U.K. 220 A T15244-3 Euro 220 A T15244-4 Aust 220 AT 15244-6* (varies w/line varies cord supplied) *This model is suppled with an IEC socket to allow use as an in- line charger .
UMAN-Charge 18 UC Series Charger/Conditioner IMPORT ANT: Never charge or condition battery packs while attempting to run the printer . Description The UC series of Charger/Conditioners is designed to charge and condition individual battery packs used on the MP , RP , Encore and Cameo series of portable printers.
19 UMAN-Charge The condition cycle for a fully charged battery is approxi- mately 90 minutes. If the “Charge OK” indicator blinks, disconnect the battery pack and wait until all the lights except the “Power “ light go out. Reconnect the battery and repeat step 3.
UMAN-Charge 20 T rickle Chargers Description These compact, cost effective chargers are designed to charge individual battery packs. T ypical charge time is 12 to 16 hours. Charging Batteries Plug the charge cable into the battery pack charger jack, and the Charger body into the appropriate A.
21 UMAN-Charge Product Support Contact the Product Support Help Desk at: Zebra T echnologies Corporation 30 Plan W ay W arwick, Rhode Island 02886.1012 USA Te lephone: +1 401.739.5800 Fax: +1 401.732.7808 e-mail: risupport@zebra.com Ask for the Help Desk In Europe: Zebra T echnologies Europe, Ltd.
Visit our W ebsite at www.zebra.com.
Ein wichtiger Punkt beim Kauf des Geräts Zebra Technologies RP (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Zebra Technologies RP noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Zebra Technologies RP - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Zebra Technologies RP reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Zebra Technologies RP erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Zebra Technologies RP besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Zebra Technologies RP verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Zebra Technologies RP. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Zebra Technologies RP gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
