Benutzeranleitung / Produktwartung ZWN 6120 L des Produzenten Zanussi
Zur Seite of 24
EN User manual Washing Machine ZWN 6120 L.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 First use _ _ _ _ _ _ .
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Always be sure, that there is no water leakage from ho- ses and their connections after the installation.
Product description 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adju stable feet 1 2 3 4 5 6 Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available).
Control panel Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot lights. These are presented by relevant numbers on the following pages.
Indicator pilot light (7) When selecting a washing programme both lights 7.1 and 7.2 illuminate. After having pressed the button 5 the only light corre- sponding to the running phase stays on. The machine starts working and the door is locked. The light 7.
Flap for powder or liquid detergent UP- The flap position if using POWDER detergent DOWN - The flap position if using LIQUID detergent during main wash If the flap is not in the desired position: MAX • Pull out the dispenser drawer until it stops. The flap is down and you wish to use powder detergent: • Turn the flap up.
The selector dial can be turned either clockwise or coun- terclockwise. Turn to position to reset programme/ Switching the machine off. At the end of the programme the selector dial must be turned to position , to switch the machine off.
If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to . After a few minutes the door can be opened (pay attention to the water level and temperature!) . After closing the door, it is necessary to select the pro- gramme and options again and to press button 5 .
Ink: depending on the type of ink, moisten the fabric first with acetone 1) , then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thor- oughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment COTTONS ECO 60° and 40° Main wash - Rinses Maximum spin speed at 1200 rpm Max. load 8 kg This programme can be selected for normally soiled cotton items.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment WOOL 40° Main wash - Rinses Maximum spin speed at 900 rpm Max. load 2 kg Washing programme for machine washable wool as well as for hand washable woollens.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment SPIN Drain and long spin Maximum spin speed at 1200 rpm Max. load 8 kg Separate spin for hand washed garments and after programmes with the Rinse Hold option selected.
Cleaning the pump The pump should be inspected regularly and particularly if: • the appliance does not empty and/or spin; • the appliance makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump; • a problem with water draining is detected (see chapter “What to do if.
Cleaning the water inlet filt ers Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked .
What to do if… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
Problem Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (cre ates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rota- tion of the drum.
Consumption values Programme Energy consumption (kWh) 1) Water consumption (litre) 1) Programme duration (minutes) 1) White Cottons 90 °C 2.1 65 145 Cottons 60 °C 1.4 63 120 Cottons 40 °C 0.6 63 140 Synthetics 40 °C 0.45 37 85 Delic ates 40 °C 0.
Unscrew the three bolts. Slide out the relevant plas- tic spacers. Open the porthole and re- move the polystyrene block fitted on the door seal. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.
The other end of the inlet hose which connects to the appliance can be turned as showe d in the picture. Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. Set the hose correctly by loosening the ring nut.
If the outlet spigot has not been used before, remove any blanking plug that may be in place. Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose (see above) to prevent waste from th e sink enter- ing the appliance.
your local council, your household waste disposal service or the shop where you purchas ed the product. Packaging materials The materials marked with the symbol are recyclable.
www.zanussi.com/shop 192985530-A-312011.
Ein wichtiger Punkt beim Kauf des Geräts Zanussi ZWN 6120 L (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Zanussi ZWN 6120 L noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Zanussi ZWN 6120 L - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Zanussi ZWN 6120 L reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Zanussi ZWN 6120 L erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Zanussi ZWN 6120 L besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Zanussi ZWN 6120 L verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Zanussi ZWN 6120 L. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Zanussi ZWN 6120 L gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
