Benutzeranleitung / Produktwartung 2000 des Produzenten Xantrex Technology
Zur Seite of 40
90-01 15-00 10/97 Fltman.pm65 OWNER'S MANUAL FLEET POWER INVERTER/BA TTER Y CHARGERS FLEET POWER 1000 FLEET POWER 2000 FLEET POWER 2500 Fleet Power 1000 & 2000 models are certified by UL to comply with FED spec-KKK-A1822, SAE spec-SAE-JRR1, for emergency vehicle application.
90-01 15-00 10/97 Fltman.pm65 INTRODUCTION General safety information for installation and operation is contained throughout this manual where it applies and are not included in this summary .
90-01 15-00 10/97 Fltman.pm65 T ABLE OF CONTENTS 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Things Y ou Should Know . . . . . . . . . . . . . . . 5 Circuit Breaker Protection Electronic Protection Power Sharing Power Switch Remote Control Programming Operation .
90-01 15-00 10/97 Fltman.pm65 INTRODUCTION This owner's manual describes the Fleet Power Inverter/Chargers from Heart Interface. These units perform three distinct functions: 1. DC to AC power inverting. 2. Automatic transfer switching between inverter power and incoming AC power .
90-01 15-00 10/97 Fltman.pm65 THINGS YOU SHOULD KNOW The optional Fleet Power Remote Control Panel provides a power switch, system status LEDs, DC V olts and DC Amps LED bargraphs.
90-01 15-00 10/97 Fltman.pm65 Power Switch The Power Switch is located on the front panel. This switch controls ON/OFF and RESET for the inverter . Expect a 3 second delay when the power switch is turned ON before the unit is activated.
90-01 15-00 10/97 Fltman.pm65 REMOTE CONTROL P ANEL V olts bargraph will stop indicating battery voltage and display the dip switch settings. It will return to indicating battery voltage only after the unit has been reset. DC Amps Bargraph These LEDs approximate DC input current in inverter mode and DC output current in battery charger mode.
90-01 15-00 10/97 Fltman.pm65 REMOTE CONTROL P ANEL Dip Switches On the back of the Fleet Power remote control panel is a set of 8 dip switches which are used to make several adjust- ments. On the switch block, each switch is numbered . . .1 through 8 and the ON posi- tion is indicated.
90-01 15-00 10/97 Fltman.pm65 REMOTE CONTROL P ANEL Use the 5 Amp setting for small genera- tors, or for charging deeply discharged batteries. Dip Switch Status Y ou can check the position of the dip switches by quickly cycling the power switch OFF/ON twice.
90-01 15-00 10/97 Fltman.pm65 Status LED Purpose INV/ CHRG (Inverter/Charg Pow er on ligh t. It will be i lluminate d whenever t he power swi tch is on (inver ter on) o r when there is incom ing AC power an d the charge r comes on. AC Input Illuminates when incoming AC power h as been appl ied and t he transfer relays have engaged.
90-01 15-00 10/97 Fltman.pm65 Feature Switch Num ber Set Point Equalize or 3 Stage Charging 1 Toggle On/Off Equalize (D o not leave on.) Off 3 Sta ge Charging* Battery Type 2 3 On On Warm Gel Cell (>80 deg. F.) Off On Cool Gel Cell (<80 deg. F.) On Off Warm Wet Cell (>80 deg.
90-01 15-00 10/97 Fltman.pm65 BA TTERIES BA TTER Y TYPES Use only deep-cycle batteries with your Fleet Power Inverter/Charger . These fall into two broad categories, wet cell and gel cell. Wet Cell Batteries T rue deep-cycle wet cell batteries are characterized by relatively thick plates that are alloyed with antimony .
90-01 15-00 10/97 Fltman.pm65 BA TTERIES Beware of so-called maintenance- free batteries . These batteries have cal- cium alloyed with the lead and hold the liquid electrolyte in a sponge-like material. They are sealed and water cannot be added. Do no confuse them with true gel cell batteries, they will not hold up to deep discharging.
90-01 15-00 10/97 Fltman.pm65 BA TTERIES Always use proper terminals for your interconnecting battery cables which are appropriate to handle the current.
90-01 15-00 10/97 Fltman.pm65 BA TTERIES T o achieve 50% cycling you should calculate your Amp-hour consumption between charging cycles and use a battery bank with twice that capacity . T o calculate Amp-hour consumption first look at the rating plate on your AC appli- ance or tools.
90-01 15-00 10/97 Fltman.pm65 Battery Charging Completely recharging wet cell deep- cycle batteries requires the battery voltage to be raised beyond what is known as the gassing point. This is the voltage at which the battery begins to bubble and gas is given off.
90-01 15-00 10/97 Fltman.pm65 BA TTER Y CHARGING NOTE: Fleet Power battery chargers are on whenever there is AC power connected to the charger input, regardless of the condi- tion of the On/Off switch.
90-01 15-00 10/97 Fltman.pm65 Gel cell batteries can accept a higher rate of charge. Consult the manufacturer for specifications. Stage 2 - Acceptance Charge The acceptance stage immediately follows the bulk charge stage. During this stage the battery voltage is held constant at the bulk charge voltage limit and the current gradu- ally ramps down.
90-01 15-00 10/97 Fltman.pm65 charging cycle. The battery voltage will increase to 16.3 using the cool temperature wet cell setting. This will cause the battery bank to gas profusely and will accomplish the following: 1.
90-01 15-00 10/97 Fltman.pm65 BA TTER Y CHARGING 1. Do not equalize gel cell batteries with the remote programmed for wet cells. 2. Always monitor the equalize charge. Provide proper ventilation for battery fumes. Do not allow any sparks during equalizing.
90-01 15-00 10/97 Fltman.pm65 BA TTER Y CHARGER VOL T AGE SETTINGS 21 d n a e p y T y r e t t a B e r u t a r e p m e T / e g a t l o V k l u B e m i T x a M t a o l F e g a t l o V e z i l a u q E e g a t l o V l l e C t e W t l o V 2 1 e r u t a r e p m e T m r a W r h 1 / 0 .
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION PRECAUTIONS AC Output Remote Jack AC Inputs Chassis Ground Lug CAUTION T o reduce the risk of electric shock and prevent premature failure due to corrosion, do not mount where exposed to rain or spray . CAUTION T o prevent fire, do not obstruct ventilation openings.
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION Key Installation Points The Power Switch must be turned OFF before you begin. 1. Observe proper polarity when connecting batteries. Reverse DC polarity will result in damage to the unit and will void the warranty .
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION 15. If multiple battery banks are to be charged, a battery selector switch can be installed, allowing the banks to be charged either individually or simultaneously .
90-01 15-00 10/97 Fltman.pm65 This procedure will connect the chassis of your unit to AC ground. In addition, the AC input and AC output green wires are connected to chassis ground. It is important to connect these wires to the AC ground bus in the circuit breaker panel.
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION Do not connect incoming AC from any source to the AC output of the inverter/ charger . This is known as back-feeding and will damage the unit and void the warranty . connect in the same fashion as the AC input wires.
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION Persons with heart problems or other conditions which make them susceptible to electric shock may still be injured by ground faults on circuits protected by the GFCI Receptacle.
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION Fleet Power inverter/chargers are not protected against DC reverse polarity . Be very careful to connect the negative and positive cable correctly or damage will result and the warranty will be void.
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION OPTION 1 29 15, 20 or 30 Amp Shore Power Inverter Runs Entire Panel In this system, the shore power is the only external AC power source available. The entire circuit breaker panel is connected to the output of the inverter/charger .
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION OPTION 2 30 Amp Shore Power and Generator . Inverter Runs Entire Panel. This system has 2 sources of AC power , shore power and generator .
90-01 15-00 10/97 Fltman.pm65 INST ALLA TION OPTION 3 50 Amp Shore Power/Generator Inverter Runs 30 Amp Sub-Panel. In this system the main circuit breaker panel contains many loads that will not operate from the inverter such as air conditioning, stove, water or space heater .
90-01 15-00 10/97 Fltman.pm65 32 INST ALLA TION OPTION 4 (Dual AC Input) Fleet Power 2500 Only • 50 Amp 120 V olt Shore Power Service • Generator The transfer switch shown, switches, either manually or automati- cally , between generator and shore power .
90-01 15-00 10/97 Fltman.pm65 DC WIRING OPTIONS DC Wiring #1 - T wo Battery* System Using Manual Battery Switch This system is simple and effective, providing the user with the ability to choose between either battery for inverter use or charging.
90-01 15-00 10/97 Fltman.pm65 DC WIRING OPTIONS DC Wiring #3 - T wo Auxiliary Batteries* with Battery Switch and One Engine Battery This system allows the inverter to use either auxiliary battery . The engine battery can always be charged by the alternator , but cannot be discharged by the inverter .
90-01 15-00 10/97 Fltman.pm65 TROUBLESHOOTING LED Number In di cat ion LED 1 Illumi nates if the unit sh uts do wn for any r eason. LED 2 Over-temperature. Allow to cool. LED 3 The u nit detec ted a fa ilure. Ca ll He art Inte rfac e Technica l Supp ort.
90-01 15-00 10/97 Fltman.pm65 TROUBLESHOOTING 1. Digital clocks either employ an internal time base or derive their time base from the incoming AC waveform. The frequency is usually well regulated at 60 Hz. The clock either counts the number of peaks in the waveform or the number of times the waveform crosses zero volts.
90-01 15-00 10/97 Fltman.pm65 GLOSSAR Y Alternating Current (AC) An electric current that reverses direction at regular intervals. Sources of alternating current are shore power , generator power , inverter power or household current. Ampere (Amp, A) The unit of measure of electron flow rate of current through a circuit.
90-01 15-00 10/97 Fltman.pm65 Power Sharing The ability of the charger to reduce its output when the AC power being consumed by the charger and external AC loads connected to the output of the inverter are in excess of the input breaker rating. V olt The unit of measure for electric potential.
90-01 15-00 10/97 Fltman.pm65 SPECIFICA TIONS 39 MODEL Nominal Battery V oltage Battery V oltage Range Low Battery Cutout AC Input V oltage Range Frequency Regulation Inverter Output Power (Continuous.
90-01 15-00 10/97 Fltman.pm65 W ARRANTY Y our Heart Interface Fleet Power Inverter/Charger is under limited warranty for a period of 12 months from date of purchase. T erms of the warranty are detailed on the warranty registration card. Please complete this card and return it to Heart Interface to register your warranty .
Ein wichtiger Punkt beim Kauf des Geräts Xantrex Technology 2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Xantrex Technology 2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Xantrex Technology 2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Xantrex Technology 2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Xantrex Technology 2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Xantrex Technology 2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Xantrex Technology 2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Xantrex Technology 2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Xantrex Technology 2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
