Benutzeranleitung / Produktwartung 883886-01 des Produzenten Wyse Technology
Zur Seite of 56
Inst allation Guide Wyse Device Manager™ Release 4.9.1 Issue: 042012 PN: 883886-01 Rev . N.
Copyright Notices © 2012, Wyse T echnology Inc. All rights reserved. This manual and the software and firmware described in it are copyrighted. Y ou may not reproduce, transmit, transcribe, store in .
Content s 1 Introduction 1 About this Guide 2 Finding the Information Y ou Need in th is Guide 2 Wyse T echnical Support 2 Related Document ation and Services 2 Wyse Online Community 2 2 Prep aring fo.
iv Contents This page intentionally blank..
1 Introduction Wyse Device Manager TM (WDM) software is the premi er enterprise solution for managing network intelligent devices simply , remotely , and secu rely .
2 Chapter 1 About this Guide This guide pr ovides the step -by-step instru cti ons you need to inst all and configur e a WDM environment. It also includes the requ irements you must address before you beg in the installation procedures.
2 Prep aring for Inst allation This chapter contain s the pre-installa tion requ irements you must co mplete to pr epare the environment for WDM inst a llation and configuration.
4 Chapter 2 • WDM Workgroup Edition Only : · Y ou do not need to obtain special lic enses to inst all WDM (you will use the WDM Workgroup Sale s Key that appears by default in the InstallShield Wizar d ). · Ensure your F TP service is running (see al so "How the WDM Installer Inst alls and Configures FTP") .
Preparing for Installation 5 • Upgrading Curre n t W DM Installations Only: · Planning for Upgrading - WDM 4.9.1 support s an upgrade from WDM version 4.9.0 ONL Y . Y ou cannot upgr ade from any other version. IMPORT ANT : Af ter upgrading to WDM 4.
6 Chapter 2 Hardware Requirement s Depending on your operating system, be sure the machine( s) to which you will install WDM meets or exce eds the minimum system requirements shown in T able 1 for 32-.
Preparing for Installation 7 Communication Port Requirement s T o perform their full range of management functions, WDM sof tware components require certain por ts to remain open on your servers, routers, an d switches.
8 Chapter 2 Upgrading Requirement s WDM 4.9.1 support s an upgrade from WDM version 4.9.0 ONL Y . Y ou cannot up grade from any other version. IMPORT ANT : Af ter upgrading to WDM 4.9.1, you must upgrade all devices with the latest HAgent p ackages available to ensure your devices can be manage d using WDM.
Preparing for Installation 9 Requirement s for Managing PCoIP Devices PCoIP devices (running ThreadX firmware) requir e a DNS Service Location (SRV ) resource record to perform the followin g actions: • Partial Check-In (heartbeat ) - Where the device performs a heartbeat check-in every 5 minutes (this amount of time is not configurable).
10 Chapter 2 Figure 2 Service Location (SR V) 3. Select the Service Location (SR V ) resource reco rd type and th en click Create Record to open the New Resource Record dialog bo x. Figure 3 New Resource Record 4. Use the following guidelines ( Domain is automatically sh own) : • Enter _Pcoip- tool in the Se rvice box.
3 Inst alling or Upgrading WDM W orkgroup Edition This section provides the deta iled procedures yo u must complete to install or upgr ade WDM Workgroup Edition .
12 Chapter 3 Inst alling or Upgrading Procedures (WDM Workgroup Edition) The WDM Workgroup Edition installation wizard automati cally detect s whether a new insta llation or an upgrade in sta llation is ne ede d, and guides you thro ugh the process. Use the following guidelines: 1.
Installing or Up grading WDM Workgroup Edition 13 • Be Sure to Carefully Follow the WDM Prerequisi te Utility - It finds out what you have and what you need , and then guides you throug h all the steps needed for your environment.
14 Chapter 3 This page intentionally blank..
4 Inst alling or Upgrading WDM Enterprise Edition This section provides the deta iled procedures yo u must complete to install or upgr ade WDM Enterprise Edition .
16 Chapter 4 About Evaluation Licensing If you are installing WDM Enterprise Edition for evalua tio n, yo u mu st use an Enterprise Evaluation License Key to install and use WDM for 30 days.
Installing or Up grading WDM Ente rprise Edition 17 Use the following guidelines: Tip Use the Correct Key - For all WDM Enterprise Edition installations or upgrades ( Ty p i c a l or Custom ) be sure .
18 Chapter 4 • If Y ou are Upgrading - Be sure to use th e correc t system administrator password ( SA Password ) for the current inst allations of your WDM Enterprise Edition . • For Ty p i c al Inst allations and Upgrade s, Use Defaults - It is recommended to use the InstallShield Wizard recommendations.
Installing or Up grading WDM Ente rprise Edition 19 Det ailed Custom Installation and Upgrade Instructions Whether you ar e pe rf or min g a Custom installation or upgrade on a single server o r multiple servers, yo u must inst all or upgrade the WDM componen t s in the following order: 1.
20 Chapter 4 WDM Dat a base Installation T ips Y ou Need to Know Depending on how you are installing, use the follo wing guidelines when pr ompted for Database configuration s during an insta llation .
Installing or Up grading WDM Ente rprise Edition 21 Figure 8 SQL Server Properties • If you have already in st alled the WDM Database on a separat e server and you are currently inst alling other WDM component s on a server - the InstallShield Wizar d will prompt you for a WDM Database confirmation.
22 Chapter 4 Sof tware Repository Installation T ips Y ou Need to Know Depending on how you are installing, use the follo wing guidelines when pr ompted for Repository configurations during an install.
Installing or Up grading WDM Ente rprise Edition 23 · Windows Authentication - This is the most secure fo rm of authentication in IIS. When you log in, Windows NT validates yo ur login and on ly your user name is transmitted over the network . Y our password is not transmitte d.
24 Chapter 4 Administrator Console Installa tion T ips Y ou Need to Know If you are installing mult iple instances of the Administrator Console ( MM C Snap-in ) in your WDM en vironment and want to us.
A Activating Y our Sales Key This appendix includes the det ailed steps you must complete to activate your Sales Key (WDM Workgroup Sales Key or WDM Enterp ris e Sales Key ).
26 Appendix A Figure 14 Licensing Wizard 4. Note your Sales Key and Non-activa te d Key numbers as you will use them in the online WDM licensing form. Tip If the server on which you inst alled the Adm.
B Uninst alling WDM When using a Microsoft Window s re move program feature (such as Add and Remove Programs or Programs a nd Features ) to remove WDM, the da tabase server will require login credentials to complete the uninst allation of WDM.
28 Appendix B Figure 17 Microsof t data execut io n prevention message - exa mple Figure 18 IIS error message - example Open the IIS W eb Sites Properties dialog box (according to the IIS docu ment ation for your server version).
C Reference and T roubleshooting: FTP , IIS, and Firewall Information Although WDM automatically in stalls and configures everythin g you need for WDM use with respect to FTP , IIS, and the Windows Fi rewall, the following refe rence information ca n be useful for unde rstanding your environment and for various troubleshooting purposes.
30 Appendix C How the WDM Inst aller Inst alls and Configures FTP Depending on your server version, use one of the following sections to underst and how FTP is installed and configured for use wit h W.
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 31 Figure 21 Select Role Services 4. Under Role Services , expan d FTP Publishing Service , select the FT P Server and FTP Management Co nsole check boxes, and then click Next to open the Confirm Inst allation Selections window .
32 Appendix C Figure 23 Default FTP Site 5. In the tree pane, right-click on Default FTP Site , and then select Prope rties to open the Properties dialog box. Figure 24 Properties 6. Click the Security Account s tab and be sure that the Allow Anonymous Connections check box is selected .
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 33 7. Click the Home Directory tab and be sure that th e Read , Writ e and Log visits check boxes are selected. 8. Click Apply , and th en click OK . 9. Close the Internet Information Se rvices (IIS) Manager window .
34 Appendix C Inst alling and Configuri ng FTP on Windows Server 2008 R2 Before setting up your own FTP server in Wi ndows, you must be sure that Internet Information Services (IIS) has already been inst alled on the server . 1. On the taskbar , click St art > Administrative T ools > Server Manager to open the Server Manag er window .
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 35 Use the following guidelines to configure FTP on Windows Server 2008 R2: 1. On the taskbar , click St art > Administrative T ools > In ternet Informati on Serv ic es (IIS) Manager to open the Internet Information Se rvices (IIS) Manager window .
36 Appendix C Figure 30 Binding and SSL Settings 4. Keep the default value for IP Address as All una ssigned and port as 21 . 5. Select the St art FTP site automa tically check box, change the SSL op tion to No SSL , and then click Next . Figure 31 Authenticatio n and Authorization Information 6.
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 37 Inst alling and Confi guring FTP on Windows 7 Before setting up your own FTP server in Wi ndows, you must be sure that Internet Information Services (IIS) has already been inst alled on the server .
38 Appendix C Figure 33 Internet Infor mation Services (IIS) Manager 2. In the tree pane, right-click on Sites , and then select Add FTP Site to begin cre ating an FTP site. Figure 34 Add FTP Site 3. Enter the FTP site name , select th e Physic al path for the FTP root directory , and then click Next .
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 39 Figure 35 Binding and SSL Settings 4. Keep the default value for IP Address as All una ssigned and port as 21 . 5. Select the St art FTP site automa tically check box, change the SSL op tion to No SSL , and then click Next .
40 Appendix C How the WDM Inst aller Inst alls and Configures IIS Depending on your operating system , use one of the following sections to unde rstand how IIS is inst alled and configured fo r use with WD M (information is presented as if you would complete the procedures manually): • "Installing IIS 7.
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 41 5. Under Roles Services , expand W eb Server , exp and Common HTTP F eatures , and then select the HTTP Redirection check box. 6. Under Web Server , ex pand Application Development and then s elect the ISAPI Extensions check box.
42 Appendix C Inst alling WebDA V Extension for IIS 7.0 1. Download the 32-bit Installa tion Package of the WebDA V Extension for IIS 7.0 from: http://blogs.iis.net/r obert_mc murray/archive/2008/03/12/ webdav-extension-for-windows-s erver-2008-r t m-is-released.
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 43 Inst alling IIS 7.5 on Windows Server 2008 R2 By default, I IS 7.5 is no t installed on Window s Server 2008 R2. Y ou can install IIS by us ing the Add Roles wizard in Server Manager .
44 Appendix C Figure 42 Select Role Services continued 8. Under Role Services , expan d Performance , and then be sure that each option is cleared ( S tatic Content Compression and Dynamic Content Compression should be cleared).
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 45 Figure 43 DefaultAppPool - Advanced Set tings c. Right-click the DefaultAppPool and select Advanced Sett ings to open th e Advanced Settings window . Figure 44 Advanced Sett ings d.
46 Appendix C Inst alling IIS 7.5 on Windows 7 By default, IIS 7.5 is not installed on Wi ndows 7. Y ou can install IIS by using the Tu r n Windows Feat ures on or off wizard in Prog rams and F eatures . 1. On the taskbar , click Start > C on tr o l P a n el to open Control Panel .
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 47 Figure 46 Internet Infor mation Services exp anded 5. Expand W eb Management T ools , and then select the IIS 6 Management Comp atibility , IIS Managemen t Console , and IIS Management Script s and T ools check boxes.
48 Appendix C Figure 47 Request Filtering 9. Under World Wide Web Services, expand Security , select the Basic Authent ication and Windo ws Authentication check boxes, and then be sure that the Request Filtering option is cleared. 10. Click OK to install IIS.
Reference an d T roub les hooting: FTP, IIS, an d Firew all Information 49 Using Windows Firewall wi th WDM If you are using Wind ows Firewall with your WDM Workgroup Edition or your WDM Enterprise Ed.
50 Appendix C This page intentionally blank..
51 Ta b l e s 1 Server Hard ware Requirem ents for 32-bit O S 6 2 Server Hard ware Requirem ents for 64-bit O S 6 3 Server Sof tware Requirements 6 4 Communication Port s 7.
Inst allation Guide Wyse De vice Manager TM Release 4.9.1 Issue: 0420 1 2 Written and publishe d by: Wyse T echnology Inc. , April 2012 Created using Fra m eM a ke r ® and Acrobat ®.
Ein wichtiger Punkt beim Kauf des Geräts Wyse Technology 883886-01 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Wyse Technology 883886-01 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Wyse Technology 883886-01 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Wyse Technology 883886-01 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Wyse Technology 883886-01 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Wyse Technology 883886-01 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Wyse Technology 883886-01 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Wyse Technology 883886-01. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Wyse Technology 883886-01 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
