Benutzeranleitung / Produktwartung WESY86303 des Produzenten Weider
Zur Seite of 36
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing or damaged parts, we will guarantee complete satisfac- tion through direct assistance from our factory .
2 T ABLE OF CONTENTS LIMITED W ARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .
3 IMPORT ANT PRECAUTIONS W ARNING: T o reduce the risk of serious injury , read the following important precautions before using the training system. 1. It is the responsibility of the owner to ensure that all users of the training system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 78 in. W idth: 64 in. Length: 70 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arm Weight Stacks Backrests Leg Press Plate Ab Pulley Station W ARNING DECAL W ARNING DECAL Thank you for selecting the versatile WEIDER ® 8630 t raining system.
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet • Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y BAG ONE” and “FRAME ASSEMBL Y BAG TWO.” Press two 2” Square Outer Caps (58) onto the Weight Base (14) in the indicated locations. Press a 2” Square Inner Cap (56) into the end of the Weight Base.
4. Slide the Front Seat Frame (8) onto the indi- cated 5/16” x 2 1/2” Carriage Bolts (49) in the P ress Base (13). Hand tighten two 5/16” Nylon Locknuts (40) onto the Carriage Bolts.
8. Lubricate the insides of the holes in the T op Weights (24) as shown. Slide a T op Weight o nto each set of Weight Guides (23). 9. Attach the T op Frame (2) to the Ab Upright (1) with two 5/16” x 2 3/4” Bolts (55), two 5/16” W ashers (20), and two 5/16” Nylon Locknuts (40).
1 1. Attach the Leg Press Plate (1 1) to the Adjustment T ube (10) with a 5/16” x 2 1/2” B olt (39), two 5/16” W ashers (20), and a 5/16” Nylon Locknut (40). Be sure that the Leg P ress Plate and Adjustment T ube are ori- ented as shown. Press a 1 3/4” Square Inner Cap (48) into the Adjustment T ube (10).
10 15. Attach a Press Arm (7) to one side of the Press Frame (12) with two 5/16” x 2 1/2” Bolts ( 39) and two 5/16” Nylon Locknuts (40). A ttach the other Press Arm (7) to the Press Frame (12) in the same manner . 16. Press a 1” Round Inner Cap (70) into one of the Press Arms (7).
1 1 18. Press a 1 3/4” Square Inner Cap (48) into the lower end of the Left Fly Arm (6). Wet the l ower end of the Left Fly Arm with soapy water . Slide a 10” Pad (22) onto the Left Arm. Repeat this step with the Right Fly Arm (5). 19. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.
12 21. Wrap the Butterfly Cable (89) around a 3 1/2” Pulley (82) as shown. Attach the Pulley and a C able T rap (80) to the bracket on the Leg Press Upright (4) with a 3/8” x 2” Bolt (50) a nd a 3/8” Nylon Locknut (42). T he Cable T rap must be oriented as shown and be positioned to hold the Cable in the groove of the Pulley .
13 25. Identify the Rear Cable (87)—this is the shortest Cable. Slide one end of the Rear C able onto the 5/16” x 3” Bolt (92). Thread another 5/16” Nylon Jam Nut (91) onto the B olt, b ut do not fully tighten it. Leave enough room between the two Jam Nuts for the Cable to pivot.
14 29. Identify the Press Cable (88)—this is the longest Cable. Attach the end of the Press C able (88) to the Large “U” Bracket (84) with a 1/4” Nylon Locknut (44) and a 1/4” W asher ( 37).
15 32. Route the Press Cable (88) over the indicated 3 1/2” Pulley (82) attached to the Pulley P lates (31). T he Cable must be routed from the direction shown. Refer to the inset draw- i ng. B e sure that the Cable is between the Cable T rap (80) and the Pulley , and that the Cable T rap is positioned to hold the Cable in place.
16 36. Route the Press Cable (88) over the indicated 3 1/2” Pulley (82) attached to the Press F rame (12). B e sure that the Cable T rap (80) is turned to hold the Cable in place a nd that the Cable is between the Pulley and the crossbar on the Press Frame.
17 40. Note: The 3 1/2” Pulley (82) used in this step was attached in step 38. It is shown r emoved for easier part identification. R oute the Press Cable (88) around the 3 1/2” Pulley (82). Be sure that the Cable T rap (80) is turned to hold the Cable in place and that the Cable is routed as shown.
18 44. Locate the remaining preassembled pair of Pulley Plates (31) and 3 1/2” Pulleys (82). Route the High Cable (85) under the indicated 3 1/2” Pulley (82). The end of the Pulley Plates (31) with two holes should be down- ward. Refer to the inset drawing.
19 48. Wrap the Low Cable (86) around a 3 1/2” Pulley (82). Attach the Pulley and a Cable T rap (80) to the Ab Upright (1) with the 3/8” x 3 3/4” Bolt (76) and a 3/8” Nylon Locknut (42). B e sure that the Cable T rap is in the indi- cated position.
51. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach the Small Backrest (18) to the Ab U pright (1) with two 1/4” x 2 1/2” Machine Screws (64) and two 1/4” W ashers (37). 52. Press a 1 1/2” Square Inner Cap (57) into the Rear Seat Frame (16).
55 56 57 SEA T ASSEMBL Y MISC. 21 58. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW T O USE THE TRAINING SYSTEM, beginning on page 22 of this manual. Before using the training system, pull each cable a few times to be sure that the cables move smoothly over the pulleys.
22 HOW T O USE THE TRAINING SYSTEM T he instructions below describe how each part of the training system can be adjusted. Refer to the exercise poster accompanying this manual to see how the training system should be set up for each exercise.
23 A TT ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (35) to the Low Cable (86) at the a b pulley station with a Cable Clip (33). A TT ACHING AND REMOVING THE SEA T T o attach the Seat (17), set the bracket on the Rear Seat Frame (16) onto the pins on the Ab Upright (1).
24 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the training system. Replace any worn parts immediately . The t raining system can be cleaned using a damp cloth and mild non-abrasive detergent.
26 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the High Cable (85), the Low Cable (86), the Rear Cable (87), the Press Cable (88), and the Butterfly Cable (89). Use the diagrams to be sure that the Cables have been assembled correctly .
27 High Cable (85) Rear Cable (87) Weight Stack— 5 High Pulley— 1 2 2 3 3 1 —T op Frame 4 —Weight Stack 4.
1/2" x 3/4" Abstandsstück (69) 2" Quadratische Innenkappe (56) 2" Quadratische Außenkappe(58) 1 3/4" Quadratische Innenkappe (48) 1" Runde Außenkappe (46) 1 1/2" .
3/8" Nylonkontermutter (43) 5/16" x 1 3/4" Bolzen (68) 3/8" x 2" Bolzen (50) 5/16" x 2 1/4" Bolzen (62) 5/16" x 2 1/2" Bolzen (39) 3/8" x 2 1/2" .
5/16" x 2" Augenbolzen (79) Kabelklammer (33) 3/8" x 5" Bolzen (74) 3/8" x 3 3/4" Bolzen (76) 5/16" x 2 3/4" Schraubenbolzen (77) 5/16" x 2 1/2" Schra.
P ART LIST—Model No. WESY86303 R0100A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
This chart is provided to help you identify the small parts used in assembly . Im po rta nt : Some parts m ay ha ve b ee n pre-assembled for shipping purposes; if you cannot find a part in the parts bags, check to see if it ha s bee n pre-assembled.
REMOVE THIS P AR T LIST/EXPLODED DRA WING FROM THE MANUAL! 81 REMOVE THIS P ART LIST/EXPLODED DRA WING FROM THE MANUAL. SA VE THE P ART LIST/EXPLODED DRA WING FOR FUTURE REFERENCE.
1 2 3 4 5 6 7 7 8 9 10 1 1 12 13 14 15 16 17 18 19 17 21 21 22 22 23 23 24 24 25 25 26 26 27 27 28 28 29 29 29 29 30 31 32 32 33 34 35 36 21 21 85 85 87 86 31 41 41 86 87 88 88 89 89 56 76 82 38 42 20.
3 4 5 6 7 12 13 14 1 19 1 21 22 22 23 23 24 24 25 25 26 26 27 27 31 32 32 33 34 35 36 21 21 8 85 87 8 31 4 86 8 7 88 8 89 8 9 5 50 3 2 0 56 82 80 43 42 50 40 69 4 0 6 9 6 7 67 40 68 37 44 40 37 68 44 .
ORDERING REPLACEMENT P ARTS T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- p ared to give the following information: 1.
Ein wichtiger Punkt beim Kauf des Geräts Weider WESY86303 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Weider WESY86303 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Weider WESY86303 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Weider WESY86303 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Weider WESY86303 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Weider WESY86303 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Weider WESY86303 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Weider WESY86303. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Weider WESY86303 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.