Benutzeranleitung / Produktwartung HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 des Produzenten Studer Innotec
Zur Seite of 26
STUDER INNOTEC TEL : ++41 (0)27 205 60 80 Rue des Casernes 57 FAX : ++41 (0)27 205 60 88 CH – 1950 Sion E-MAIL : info@studer-innotec.com User’s and installer’s Manual Sine wave Inverter, Battery.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 2/80 English description .................................................................................................................. 5 1 General Information .............................................
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 5/80 English description 1 General Information 1.1 Operating instructions This manual is part of the delivery pa ckage of every HP-COMPACT inverter-charger. It serves as guidelines for safe and e fficient operation of HP-COMPACT.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 6/80 1.4 Liability Disclaimer Respecting this manual, servicing and method of installation, functioning, application and maintenance of the appliance can not be controlled or supe rvised by STUDER INNOTEC.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 7/80 − Plenty of fresh water and soap must be ready at hand so that in case of acid coming in contact with skin, eyes and cl othes, the areas in question can be thoroughly washed. − If acid enters the eyes, you must thor oughly wash them with cold running water for at least 15 minutes.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 8/80 connection between Neutra l and earth in inverter mode only may be done by installing a bridge internally to the unit. Please contact your installer regarding th is point. (2) Remote control for remote adjustment of the input limi t.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 9/80 2.3 Battery connecting Lead-acid batteries are normally available in blocks of 2V, 6V or 12V. In most cases, to generate the necessary operating voltage and the capacity of the batteries for the HP-COMPACT many batteries have to be c onnected together in pa rallel and or in series.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 10/80 3 Mounting and installing 3.1 Installation place The location of the HP-COMPACT must be driven by the following criteria: − Protection from unauthoriz.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 11/80 A Battery +/- Connection terminal (M8) for battery cable (HPC 4400-24/6000- 48/8000-48 with fuse) B Reserved - C Remote contr. Connection termi nal for Remote Control RCC-01 D Transfer delay Slide switch for Transfer Delay E Equalize Slide switch for equalization of the Battery F Temp.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 12/80 charge, the same slide switch can be set in ON position. In case of doubt leave the setting in OFF position. This will allow an equalizing cycle (higher end of charge voltage) during the next charge process.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 13/80 including the battery. If afte r the fuse replacement and after re-connection of the battery with the right polarity, the HP-COMPACT remains out of order, it must be brought back to your merchant for service.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 14/80 4 Control 4.1 Display and control parameters.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 15/80 4.2 Light Emitting Diodes (LED) LED Marking LED lit LED blinks 1 AC IN Voltage corresponding to self-adjusted values is at the AC IN input.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 16/80 25 POWER MONITOR Display the value of the output power in % of Pnom (in Inverter Mode) and the charge cu rrent in Amps (in Charger Mode). In this mode the red LED indicates that power sharing is in use (>100A).
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 17/80 time, then it no longer switches on automat ically. The LED 13 remains lit. Press the push button 19 „ON/OFF“ in order to switch on the Inverter.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 18/80 4.6 The battery charger 4.6.1 Cycle of charge The full automatic HP-COMPACT Battery Char ger is adjusted at the factory so that most lead-acid and lead-gel batteries can be charged to the maximum.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 19/80 carried out for 20 minutes (factory setting). During such a charge cycle the LED 14 is lit and during equalizing it is blinking. Charge cycle with equalization can be started independently from the actual program.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 20/80 The measure system built in the HP-COMPACT takes into account t he battery voltage, the discharge and charge current as we ll as the undulation of the voltage. If the battery and the HP-COMPACT are used a ccording to their technical data, the battery state of charge is displayed accura tely.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 21/80 4.7.1 Set the transfer voltage threshold The voltage threshold of the transfer c an be adjusted between 150 to 230V with the turning knobs (23). From factory this val ue is 200V. Most appliances can work on this voltage.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 22/80 − Over temperature (LED 10 lit) − Overload (LED 11 lit) − Over or less voltage of batteri es (LED 12 lit or blinking) − HP-COMPACT is turned off manua lly or with a fault (LED 13 lit) In case this function is not wished, it mu st be modified by programming according to procedure in chap.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 23/80 actual temperatures, a te mperature sensor can be c onnected to the HP-COMPACT. The compensation through the sensor is –3mV/°C/Cell.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 24/80 5.2 Reset value (default settings) To come back to the default settings, press simultaneously on the push buttons 20/21 during at least 2 seconds. A beep wil l confirm the comeback to the factory settings.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 25/80 5.3.2 Table of voltage and timing threshold The voltage levels (low voltage, float c harge, end of charge and equalization) and the du-ration of the absorption charge can be changed.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 26/80 like this the Auxiliary Cont act works with the lowest set condition and stops when it has reached the highest program med condition through charging.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 27/80 5.5 Disabling some of the HP-COMPACT functions Each different function charger, inverter an d transfer can be disabled. This is useful for specific applications witch required to disable some of these three functions.
STUDER INNOTEC HP-COMPACT HP-COMPACT V5.4 28/80 8 Technical Data.
Ein wichtiger Punkt beim Kauf des Geräts Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
