Benutzeranleitung / Produktwartung programming the cpu 314c-2dp des Produzenten Siemens
Zur Seite of 25
A utomation and Drive s - SCE T I A Training Document Page 1 of 25 Module Training Document for Comprehensive Automation Solutions Totally Integrated Automation (T I A) MODULE A5 Programming the CPU 3.
A utomation and Drive s - SCE T I A Training Document Page 2 of 25 Module This document has been written by Siemens AG for tr aining purposes for the project entitled "Siemens Automation Cooperates with Education (SCE)". Siemens AG accepts no responsibility fo r the correctness of the contents.
A utomation and Drive s - SCE T I A Training Document Page 3 of 25 Module SEITE: 1. Forew ord .............................................................................................................. 4 2. Notes on Using the CPU 314C-2DP .........
A utomation and Drive s - SCE T I A Training Document Page 4 of 25 Module 1. FOREWORD In terms of its contents, module A5 belongs to the teaching unit entitled "Basic Principles of STEP 7 Programming' .
A utomation and Drive s - SCE T I A Training Document Page 5 of 25 Module Hardw are and softw are needed 1 PC, operating system Windows 2000 Professional starting with SP4 /XP Professional starting with SP1/Server 2003 with 600 MHz and 512 RAM, free hard disk memory approx.
A utomation and Drive s - SCE T I A Training Document Page 6 of 25 Module 2. NOTES ON THE USE OF THE CPU 314C-2DP The CPU 314C-2DP is shipped with an integrated PROFIBUS DP interface and integrated inputs/outputs. The following PROFIBUS protocol profile s are available for the CPU 314C-2DP: - DP interface as master according to EN 50170.
A utomation and Drive s - SCE T I A Training Document Page 7 of 25 Module 2.1 OPERATING THE CPUS 31XC Operator control and display elements The following illustration shows the operator c ontrol and display elements of a CPU 31xC. The arrangement and number of elements in so me CPUs differ from this illustration.
A utomation and Drive s - SCE T I A Training Document Page 8 of 25 Module Status and fault/error displays The CPU has the following LED displays: Slot for the SIMATIC Micro Memory Card (MMC) A SIMATIC Micro Memory Card (MMC) is used as a memory module for the CPU 31xC.
A utomation and Drive s - SCE T I A Training Document Page 9 of 25 Module 2.2 MEMORY AREAS OF THE CPU 31XC Foreword Notes H H a a r r d d w w a a r r e e c c o o n n f f i i g g u u r r a a t t i i o .
A utomation and Drive s - SCE T I A Training Document Page 10 of 25 Module Retentivity Your CPU 31xC has retentive me mory. Retentivity is implement ed on the MMC and on the CPU.
A utomation and Drive s - SCE T I A Training Document Page 11 of 25 Module 3. CREATING THE HARDWARE CONFIGURATION FOR THE CPU 314C-2DP In Step 7, files are managed with the 'SIMATIC Manager'. Here, program blocks can be copied, for example, or called for further processing with other tools by clicking on them with the mouse.
A utomation and Drive s - SCE T I A Training Document Page 12 of 25 Module The hardware configuration of the PLC is mapped in the 'SIMATIC 300 Station' and 'CPU' folders. This is done in the special case where a c onfiguration is created with the CPU 314C-2DP.
A utomation and Drive s - SCE T I A Training Document Page 13 of 25 Module 3. The project is now assigned the name 'CPU314C_2DP' under 'Name' ( → CPU314C_2DP → OK) 4.
A utomation and Drive s - SCE T I A Training Document Page 14 of 25 Module 5. Open the configurati on tool by double-clicking on 'Hardw are' .
A utomation and Drive s - SCE T I A Training Document Page 15 of 25 Module 7. Insert a rail by double-clicking on 'Rail' ( → SIMATIC 300 → RACK-300 → Rail).
A utomation and Drive s - SCE T I A Training Document Page 16 of 25 Module 8. From the hardware catalog, you now can sele ct any of the modules that are also plugged into the real rack and insert them in the configuration table.
A utomation and Drive s - SCE T I A Training Document Page 17 of 25 Module 9. In the next step, we drag the CPU 314C-2DP ont o the second slot. When this is being done, the order number and the version of the CPU can be read on the front of the CPU. ( → SIMATIC 300 → CPU-300 → CPU 314C-2DP → 6ES7 314-6CF00-0AB0).
A utomation and Drive s - SCE T I A Training Document Page 18 of 25 Module 11. The properties of some modules can be altered ( → Click on module → Change properties → OK). For example, a clock memory c an be specified for all CPUs ( → Cycle/Clock memory → ∨ Clock memory → Memory Byte 100).
A utomation and Drive s - SCE T I A Training Document Page 19 of 25 Module 12. With most S7-300 CPUs, the addresse s of the I/O modules can be altered. This is done by double-clicking on the correspondi ng modules and altering their settings in the 'Addresses' tab.
A utomation and Drive s - SCE T I A Training Document Page 20 of 25 Module 13. By clicking on the and buttons, the configuration table is now first stored and converted, and then loaded into the PLC.
A utomation and Drive s - SCE T I A Training Document Page 21 of 25 Module 4. WRITING A STEP 7 PROGRAM We are writing the program to be tested in the st atement list language (STL), and it only contains two lines. Here, the frequencies of the MB100 clock memory byte activated in the hardware are to be read out on an output byte.
A utomation and Drive s - SCE T I A Training Document Page 22 of 25 Module 15. In the SIMATIC Manager, double-click on the 'OB1' block to open it ( → OB1) 16. As an option, you can enter the properties of the OB1 for documentation purposes and accept them with 'OK' .
A utomation and Drive s - SCE T I A Training Document Page 23 of 25 Module 17. 'LAD/STL/FDB Program S7 Blocks’ is an editor which allows you to create your STEP 7 program as you require. To this end, the OB 1 organization block with the first network has already been opened.
A utomation and Drive s - SCE T I A Training Document Page 24 of 25 Module 5. TESTING THE STEP 7 PROGRAM The STEP 7 program to be tested can now be loaded into the PLC. In our case, this is only OB1. 18. Save the organization block with and load it into the PLC by clicking on .
A utomation and Drive s - SCE T I A Training Document Page 25 of 25 Module 19. To start the program, move the key switch to the RUN position. Click on the symbol to view the program in 'OB1' .
Ein wichtiger Punkt beim Kauf des Geräts Siemens programming the cpu 314c-2dp (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Siemens programming the cpu 314c-2dp noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Siemens programming the cpu 314c-2dp - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Siemens programming the cpu 314c-2dp reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Siemens programming the cpu 314c-2dp erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Siemens programming the cpu 314c-2dp besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Siemens programming the cpu 314c-2dp verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Siemens programming the cpu 314c-2dp. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Siemens programming the cpu 314c-2dp gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
