Benutzeranleitung / Produktwartung PFSY59001 des Produzenten ProForm
Zur Seite of 32
USER'S MANUAL QUESTIONS? As a manufacturer , we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory . TO A VOID DELA YS, PLEASE CALL DIRECT TO OUR T OLL-FREE CUST OMER HOT LINE.
2 T ABLE OF CONTENTS IMPORT ANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORT ANT PRECAUTIONS 3 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are ade- quately informed of all precautions.
4 BEFORE YOU BEGIN ASSEMBLED DIMENSIONS: Height: 76.0 in. Width: 86.5 in. Length: 91.5 in. Foot Plate Low Pulley Station High Pulley Station Lat Bar Leg Lever Butterfly Arms Press Arms Leg Press Seat .
5 ASSEMBL Y Make sure you have the following tools: • T wo (2) adjustable wrenches • One (1) standard screwdriver • One (1) phillips screwdriver • One (1) rubber mallet •Y ou will also need grease or petroleum jelly , a small amount of soapy water , and clear tape or masking tape.
1. Locate and open the parts bags labeled “FRAME ASSEMBL Y .” See the inset drawing. Insert two 1 1/2” x 2 1/2” Inner Caps (83) and two 3/8” x 2” Carriage Bolts (92) into the Butterfly Base (4). Insert two 1 1/2” x 2 1/2” Inner Caps (83) into the indicated ends of the Butterfly Base (4) and the Press Base (6).
4. Attach the Butterfly Seat Frame (14) to the Butterfly Upright (1) with two 3/8” x 3 3/4” Bolts (102), two 3/8” W ashers (48), and two 3/8” Nylon Locknuts (50). Attach the Butterfly Seat Frame (14) to the Butterfly Front Leg (3) with two 3/8” x 3 3/4” Bolts (102), two 3/8” W ashers (48) and two 3/8” Nylon Locknuts (50).
8 89 48 48 48 89 51 6 50 48 21 Slot 15 8. See the inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the W eight Bumpers (51) and into the holes in the Press Base (6).
9 48 62 50 48 33 9 11 . Secure the Press T op Frame (9) to the Butterfly T op Frame (33) with two 3/8” x 3 1/4” Bolts (62), two 3/8” W ashers (48), and two 3/8” Nylon Locknuts (50).
10 14 48 48 10 84 101 10 101 48 48 53 53 14. Insert a 2” Round Inner Cap (101) into the end of a Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8” x 1” Bolts (84) and two 3/8” W ashers (48). Repeat this step with the other Butterfly Arm (10).
20. Locate and open the parts bags labeled “CABLE ASSEMBL Y” and “PULLEYS.” Locate the Butterfly Cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the Butterfly Cable to the Right Pivot Arm (85) with a 5/16” x 2 1/4” Shoulder Bolt (79) and a 5/16” Nylon Jamnut (105).
12 22. Remove the preassembled 3/8” x 2” Bolts (54) from one set of Adjustable Pulley Plates (23). W rap the Butterfly Cable (73) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
13 26. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24). Insert the Ab Cable down through the Press T op Frame (9). Slide a 3/8” W asher (48) and a 5/8” x 3/4” Bushing (66) onto a 3/8” x 3 1/4” Bolt (62). Slide the Bolt through the Press T op Frame (9) and the 3 1/2” Pulley (24).
14 30. Locate the Weight Cable (72). Note that one end of the Weight Cable has a bolt on it, and the other end has a ball on it. Lay the Weight Cable (72) inside the bracket on the Butterfly Base (4) in the manner shown. Attach a 3 1/2” Pulley (24) to the bracket with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
15 35 36 37 34. Wrap the W eight Cable (72) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) to the Butterfly Upright (1) with a 3/8” x 4 3/4” Bolt (60), a 3/8” W asher (48), and a 3/8” Nylon Jamnut (63). Be sure that the Cable T rap is turned to hold the Cable in place.
16 38. Wrap the W eight Cable (72) around a 3 1/2” Pulley (24). Attach the Pulley and a Cable T rap (25) between the lowest holes in the Adjustable Pulley Plates (23) hanging from the Ab Cable (47) with a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
17 42. Locate the Leg Press Cable (75) . Attach the Leg Press Cable to the indicated side of the Press Upright (2) with a 3/8” x 3 3/4” Bolt (102) and a 3/8” Nylon Locknut (50). Do not tighten the Nylon Locknut yet. W rap the Leg Press Cable (75) around a 3 1/2” Pulley (24) in the direction shown.
18 46. Remove the 3/8” Nylon Locknut (50) from the indi- cated 3/8” x 5 1/2” Bolt (55). W rap the Leg Press Cable (75) around a 3 1/2” Pulley (24). Secure the Pulley and a Cable T rap (25) to the 3/8” x 5 1/2” Bolt (55) on the indicated side of the Press Base (6) with the 3/8” Nylon Locknut (50).
19 50. Locate and open the parts bag labeled “SEA T ASSEMBL Y .” Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4” x 3/4” Bolts (49). Repeat this step with the other Seat (not shown) and the Press Seat Frame (not shown).
20 54 55 56 91 46 3 39 54. Lubricate a 1/2” x 4” Bolt (68). Attach the Foot Press Plate (29) to the Press Leg Lever (90) with the Bolt and a 1/2” Nylon Jamnut (36). 55. Press two 3/4” Round Inner Caps (43) into each of the two Pad T ubes (42).
21 ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise.
22 AT T ACHING THE AB STRAP TO THE AB PULLEY ST A TION Attach the Ab Strap (81) to the Ab Cable (47) at the ab pulley station with a Cable Clip (69). ADJUSTING THE BACKREST To adjust a Backrest (12), .
23 WEIGHT RESIST ANCE CHART This chart shows the approximate weight resistance at each weight station. “T op” refers to the 10 lb. top weight. The other numbers refer to the 10 lb. weight plates. The butterfly arm resistance listed is the resistance for each butterfly arm.
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately . The weight system can be cleaned using a damp cloth and mild non-abrasive detergent.
25 CABLE DIAGRAMS The cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the Ab Cable (47), the Butterfly Cable (73), and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly .
26 We ight Cable (72) 2 3 1—Low Pulley 4 8 11 12—Weight Stack 7 6 5 Cable ID 72 47 75 73 9 10.
5/16" Nylon Jamnut (105) Cable Clip (69) "V" Pulley (27) (Not shown to scale) 3 1/2" Pulley (24) (Not shown to scale) Retainer Ring (31) 4 1/2" Pulley (82) (Not shown to scale.
5/16" x 2 1/4" Shoulder Bolt (79) 3/8" x 1" Bolt (84) 3/8" x 1 3/4" Bolt (57) 3/8" x 6" Bolt (59) 1/2" x 4" Bolt (68) 3/8" x 4 3/4" Bolt (60.
2" Square Inner Cap (28) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2” Inner Cap (83) 2 1/2" Square Inner Cap (76) 3” Round Inner Cap (78) 2” Round Inner Cap (78).
P ART LIST—Model No. PFSY59001 R0402A Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty .
92 92 49 39 49 23 25 24 25 24 23 50 54 23 25 24 25 24 23 50 44 35 49 86 65 77 101 65 86 77 64 25 24 60 96 68 36 25 24 50 8 68 29 36 68 36 50 25 24 25 24 59 90 78 102 48 50 80 40 20 50 83 6 60 24 25 50.
ORDERING REPLACEMENT P ARTS To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays). T o help us assist you, please be pre- pared to give the following information: 1.
Ein wichtiger Punkt beim Kauf des Geräts ProForm PFSY59001 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ProForm PFSY59001 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ProForm PFSY59001 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ProForm PFSY59001 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ProForm PFSY59001 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ProForm PFSY59001 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ProForm PFSY59001 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ProForm PFSY59001. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ProForm PFSY59001 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
