Benutzeranleitung / Produktwartung 3610 des Produzenten Acer
Zur Seite of 93
Aspire 3610 Series Service Guide PRINTED IN T AIW AN Service guide files and updates are availab le on the ACER/CSD web; for more information, please refer to http://csd.
II Revision History Please refer to the table below for the updates ma de on Aspire 3610 service guide. Date Chapter Up dates 2005/07/21 Chapter 1 Revise information on “H ardware S p ecification and Configurations”. 2005/10/24 Chapter 1 Revise battery vendor and specification on page 24.
III Copyright Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any.
IV Conventions The following conventi ons are used in this manual: SCREEN MESSAGES Denotes actual messages that appe ar on screen. NOTE Gives bits and pieces of additional information related to the current topic. W ARNING Alerts you to any damage that might result from doing or not doing specific actions.
V Preface Before using this information and the product it s upports, please read the fo llowing general info rmation. 1. This Service Guide provides you with all techni cal information relating to the BASIC CON FIGURA TION decided for Acer's "glo bal" product offering.
VI.
3 T able of Contents Chapter 1 System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . .
4 T able of Contents Chpater 4 Troubleshooting 55 System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 1 Features Below is a brief summary of the computer ’s many feature: Platf orm and memroy T Intel ® Pentium ® M 725A Pro cessor (2 MB L2 cache, 1.6GHz, 400MHz FSB) T Intel ® Cel eron M 360/370/380 Processor (1 MB L2 cache, 1.40/1.50/1 .
2 Chapter 1 T WLAN (manufactu ring option) : integrated Acer InviLink TM 802.1 1b/g WI-Fi ® CERTIFIED TM solution; Acer SignalUp techn ology support T WP AN (manufacturing option): integrated Bluetoo.
Chapter 1 3 System Block Diagram A A B B C C D D E E 4 4 3 3 2 2 1 1 Title Size Document Number Rev Date: Sheet of Acer Incorporated 8F, 88, Sec.1, Hsin Tai Wu Rd.
4 Chapter 1 Board Layout To p V i e w 1 LCD1 LCD Cable Connector 7 BA T1 Battery Pack Connector 2 MIC1 Micr ophone Cable Connector 8 U14 ENE KB3910SF C1 3 LID1 Lid Switch Cable Connector 9 U20 R TL810.
Chapter 1 5 Bottom V iew NOTE: This is engineering samp le. The image above may not be exactly the same as the real main board you get. 1 DC1 Power Jack 12 ODD1 ODD Connector 2 LAN1 Ethernet Port+Mode.
6 Chapter 1 Jumper Settings 7 U35 CPU Socket 18 U59 ENE CB-1410QF 8 DM2 DIMM Slot1 19 LIN1 Microphone/Line- in Jack 9 DM1 DIMM Slot2 20 LOUT1 Headphones/S peakers/Line -Out Jack 10 U45 North Bridge (I.
Chapter 1 7 An Aspire tour After knowing your computer features, let us show you around your new T ravelMate computer . Front V iew # Icon Item Description 1 Display screen Also called LCD (liquid-crystal display), displays computer output. 2 Power button T urns the computer on and off.
8 Chapter 1 Closed Front V iew # Icon Item Description 1 S peakers Left and right speakers deliver stereo audio output. 2 Bluetooth ® communication button/ indicator Press to enable/disable Bluetooth function. Lights to indicate the status of Bluetooth- communications (manufacturing option).
Chapter 1 9 Left V iew Right V iew # Icon Item Description 1 3 USB 2.0 Ports Connects to USB 2.0 devices (e.g., USB mouse, USB camera). 2 PC Card slot Accepts T ype II PC Card.
10 Chapter 1 Re a r P a n e l # Icon Item Description 1 Security Keylock Connects to a Kensington-compatible computer security lock. 2 Power jack Connects to an AC adaptor . 3 Ethernet (RJ-45) port Connects to a Fast Ethernet network. 4 Modem (RJ-1 1) port Connects to a phone line.
Chapter 1 11 Bottom Panel Indicators The computer has four easy-to-read status indicators on the upper-right above the keyboard, and four on the front panel. # Item Description 1 Memor y bay Houses the computer ’s main memory . 2 Battery lock Locks the battery in place.
12 Chapter 1 The power , battery an d wireless communication status indicators are visible even when th e LCD display is closed. NOTE: 1. Charging : The light shows amber when the battery is charging. 2. Fu lly charged: The light sho ws green when in AC mode.
Chapter 1 13 To u c h p a d The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds as you move yo ur finger across the surface of the touchpad. The centra l loca tion on the palmrest provides optimum comfort and support.
14 Chapter 1 T Move your finger across the touchpad (2) to move the cursor . T Press the left (1) and right (4) b uttons locat ed beneath the touchpad to perform selecti on and execution functions. These two buttons are simila r to the left and right buttons on a mouse.
Chapter 1 15 Using the K eyboard The keyboard has full-sized keys and an embedd ed keypad, separate cursor keys, two Windows keys and twelve function keys. Lock K eys and embedded numeric keypad The keyboard has three lock keys which yo u can toggle on and off.
16 Chapter 1 Hot K eys The computer employs hotkeys or key combinations to access most of the computer ’ s controls like sreen brightness, volume out put and the BIOS utility . T o activate hot keys, press and hold th e < Fn> key before pressing the other key in the hotkey combination.
Chapter 1 17 Special K ey Y ou can locate the Euro symbol and US dollar sign at th e upper-center and/or bottom-right of your keyboard. To t y p e : Fn-F4 Sleep Puts the computer in Sleep mode. Fn-F5 Display toggle Switches display output between the display screen , external monitor (if connected) and bo th.
18 Chapter 1 The Euro symbol 1. Open a text editor or word processor. 2. Either directly press the <Euro> symbol at the bottom-right of the keyboard, or hold <Alt Gr> and the n press the <5> symbol at the upper-cente r of the keyboard.
Chapter 1 19 Hardware Specifications and Configurations Processor Item Specification CPU type Intel ® Pentium ® M 725A Processor (2 MB L2 cache, 1.6GHz, 400MHz FSB) Intel ® Celeron M 360/370/380 Processor (1 MB L2 cache, 1.
20 Chapter 1 NOTE: Above table lists s ome system memory configur ations. Y ou may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 co uld be reversed.
Chapter 1 21 Data throughput 723 bps (full speed data rate) Protocol Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 wh en SIG specification is ratified). Interface USB 1.1 Connector type Mini-USB Wireless Module 802.1 1b/g (optional device) Item S pecification Chipset Atheros/Broadcom Data throughput 1 1~54 Mbps Protocol 802.
22 Chapter 1 Performance S pecification With CD Diskette With DVD Diskette T ransfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Sustained: Max 10.8Mbytes/sec Buffer Memory 2MB Interface Enhanced IDE(A T API) compatible Applicable disc format DVD: DV D-ROM, (DVD-5, DVD-9, DVD-10, D VD-18),DVD-R (read, single border), DVD-RW , DVD-RAM (2.
Chapter 1 23 Compatibility AC97 Mixed sound source Line-in, CD V oice channel 8/16-bit, mono/stereo Sampling rate 44,1 KHz (48K byte for AC97 interface) Internal microphone Y es Internal speaker / Quantity Y es/2 Vid eo I n te rf a c e Item S pecification Chipset Built-in Intel ® 910GML Package 35.
24 Chapter 1 VGA Built in Intel ® 910GML LAN RealT ek 81 10CL USB 2.0 Built in ICH6-M Super I/O controller This mode l does not employ Super I/O c ontroller since it does not have FIR, IEEE 1394 function MODEM Built-in ICH6-M Bluetooth Broadcom Wireless 802.
Chapter 1 25 T ypical White Luminance (cd/m 2 ) also called Brightness 180 (5 point average) 150 (5 point average) 160 150 Luminance Uniformity N/A N/A 70 Contrast Ratio 300 300 250 Response T ime (Optical Rise T i me/Fall Ti m e ) m se c 24/1 1 15/35 8/17 10/2 5 Nominal Input V oltage VDD +3.
26 Chapter 1 Support Color 262K 262K 262K colors (RGB 6-bit data driver) Viewing Angle (degree) Horizontal: Right/Left V ertia l: Upper/Lower 45/45 15/35 45/45 15/35 45/45 15/35 T e mperature Range( C.
Chapter 2 29 BIOS Setup Utility The BIOS Setup Utility is a hardware configuration prog ram built into y our computer ’s BIOS (Basic Input/ Output System). Y our computer is already properly configu red and optimi zed, and you do not need to run this utility .
30 Chapter 2 Navigating the BIOS Utility There are six menu options: Info., Main, Sy stem Devices, Security , Boot, and Exit. Follow these instructio ns: T T o choose a menu, use the cursor left/right keys ( zx ). T T o choose a parameter , use the cursor up/down keys ( wy ).
Chapter 2 31 Inf ormation NOTE: The system information is su bject to diff erent models. Parameter Description CPU T ype This field shows the CPU type and speed of the system. IDE1 Model Name This field shows the model na me of HDD installed on primary IDE master .
32 Chapter 2 Main The Main screen disp lays a summary of your computer hardware information, and also inclu des basic setup parameters. It allows the user to specif y st andard IBM PC A T system parameters. NOTE: The screen above is for your reference only .
Chapter 2 33 The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. NOTE: The sub-items under each device wil l not be shown if t he device control is set to d isable or auto. This is because the user is not allowed to control the settings in these cases.
34 Chapter 2 Security The Security screen co ntains parameters that help sa feguard and protect your co mpu ter from unauthorized use. PhoenixBIOS Setup Utility Information M a i n Boot Item Specific .
Chapter 2 35 The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. NOTE: When you are prompted to enter a password, you ha ve three tries be fore the system halts. Don’t forget your password.
36 Chapter 2 1. Use the w and y keys to highlight the Set Sup ervisor Password parameter and press the e key . The Set Password box appears: 2. T ype the current p assword in the Enter Current Passwor d field and press e . 3. Press e twice without typing anyth ing in the Enter New Password and Confirm New Password fields.
Chapter 2 37 If the new password and confirm new password strings do not match, the screen will display the following message..
38 Chapter 2 Boot This menu allows the user to deci de the order of boot de vices to load the operatin g system. Bootable devices includes the distette drive in m odule bay , the onboard hard disk drive an d the CD-ROM in module bay .
Chapter 2 39 Exit The Exit screen contains parameters that help safegua rd and protect your computer from unauthorized use. The table below describes the parameters in this screen. Parameter Description Exit Saving Changes Exit System Setup and save your changes to CMOS.
40 Chapter 2 BIOS Flash Utility The BIOS flash memory upd ate is required for th e following conditions: T New versions of system programs T New features or options T Restore a BIOS when it becomes corrupted. Use the Phlash util ity to update the system BIOS flash ROM.
Chapter 3 41 This chapter contains step-by-s tep procedures on how to disass emble the notebook computer for maintenance and troubleshooting . T o disassemble th e computer , you ne ed the following t.
42 Chapter 3 General Inf ormation Bef ore Y ou Begin Before proceeding with the disassembly procedure, make su re that you do the following: 1. T urn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cab les from the system.
Chapter 3 43 Disassembly Procedure Flowchart The flowchart on the succeed ing page gives you a graphic represen tation on the entire disassembly sequen ce and instructs you on the components that need to be remo ved during servicing .
44 Chapter 3 Screw List Item Description Part Number A SCW HEX NYL I#R-40/O#4-40 L5.5 34.00015.081 B SCREW MACH W AFER M2*L4 NI 86.00059.220 (PC Card slot x4) C CPU SCREW M2.5*4.3L (2.3 KG) 86.00D01.230 D CPU SCREW M2.5*4.3L (1.55 KG) 86.00D02.230 E SCREW M2.
Chapter 3 45 R emoving the Battery Pack 1. Unlock the battery lock. 2. Slide the battery latch then remove the battery ..
46 Chapter 3 R emoving the Wireless LAN Card/the HDD Module/the Memory/the ODD Module and the LCD Module R emoving the Memory and the HDD Module 1. Remove the three screws fastening the HDD cover . 2. Detach the HDD cover carefully . 3. Disconnect the wireless antenna.
Chapter 3 47 3. Pop out the memory . 4. Remove the memory from the DIMM socket. R emoving the ODD Module 1. Remove the screws fastening the ODD module as shown. 2. Use a flat headed screwdriver to push th e ODD module outwards then remove it. R emoving the LCD Module 1.
48 Chapter 3 . 6. Pull out the wireless LAN antenna from the main uni t as shown. 7. T ake out the LCD cabl e from the ma in unit then disconne ct the cable. 8. Remove two screws fastening the LCD module. 9. Remove another two screw s on the bottom as shown.
Chapter 3 49 Disassembling the Main Unit Separate the Main Unit Into the Upper and the Lower Case Assembly 1. Disconnect the touchpad cable from the main board. 2. Disconnect the microphone cable then remove the microphone . 3. Remove one screw holding the upper case and the low er case assembly .
50 Chapter 3 3. Detach the touchpad bracket carefully . 4. Then detach the touchpad from the touchpad bracket. Disassembling the Lower Case Assembly 1. Disconnect the bluetooth cable then remove the bluetooth modul e. 2. Disconnect the speaker set cable from the main board.
Chapter 3 51 8. Disconnect the modem board cable from the main board. 9. Remove the two screws holding the m odem board then detach the modem board. 10. Disconnect the modem cable fro m the modem bo ard. 11 . Remove the three screws holding the CPU heatsink then remove it.
52 Chapter 3 15. Remove the three screws fastening the speaker set. 16. T ear off the tape holding the speaker set. 17. T ake out the sp eaker set from the lower case.
Chapter 3 53 Disassembling the LCD Module 1. Remove the four screw caps as shown. 2. Remove the four screws holding the LCD bezel. 3. Then detach the LCD bezel from the LCD module. 4. Remove the two screws fastening the LCD inverter . 5. T ake out the LCD inverter fro m the LCD cover , then disconnect the LCD cable from the inverter .
54 Chapter 3 Disassembling the External Modules Disassembling the HDD Module 1. Remove the two screws holding the HDD bracket on one side. 2. Remove another two screws holding th e HDD bracket on the other side. 3. Then take the hard disc drive out from the HDD bracket.
Chapter 4 55 Use the following procedure as a gui de for computer problems. NOTE: The diagnosti c tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false e rrors and invalid system responses.
56 Chapter 4 System Check Procedures External Diskette D rive Check Do the following to isolate the problem to a controller, dr iver , or diskette. A write-ena bled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than on e label attached to it.
Chapter 4 57 If any of these devices do not work, reconnect the cable connector and rep eat the failing o peration. Memory check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the doa gmpstotics prog ram (please refer to mai n board.
58 Chapter 4 Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figu re 1. If the voltage is not correct , replace the power ad apter . 2. If the voltage is within the range, do the following: T Replace the System board.
Chapter 4 59 Check the Battery Pack T o check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Mete r , conf irm that if t he parameters sh own in the screen for Current Power Source and T otal Battery Power Remaining are correct.
60 Chapter 4 Power-O n Self-T est (POST) Error Message The POST error message index lists the error message and their possible causes. The most like ly cause is listed first.
Chapter 4 61 Index of Error Messages Error Code List Error Codes Error Messages 006 Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2.
62 Chapter 4 Real time clock error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility .
Chapter 4 63 Error Message List No beep Error Messages FRU/Action in Sequen ce No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 57.. Ensure every connector is connected tig htly and correctly .
64 Chapter 4 Phoenix BIOS Beep Codes Code Beeps POST Routine Description 02h V erify R eal Mode 03h Disable Non-Maskable Interru pt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize.
Chapter 4 65 46h 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optio.
66 Chapter 4 8Ch Initialize floppy controller 8Fh Determine number of A T A drives (optional) 90h Initialize hard-disk controllers 91h Initialize local-bus hard-disk controllers 92h Jump to UserPatch2.
Chapter 4 67 D2h Unknown interrupt Code Beeps E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize the system timer E4h Initialize system I/O E5h Check force reco.
68 Chapter 4 Index of Symptom-to-FR U Error Message LCD-Related Symptoms Symptom / Error Action in Sequence LCD backlight doesn't work LCD is too dark LCD brightness cannot be adjusted LCD contrast cannot be adjusted Enter BIOS Utility to execute “Load Setup Default Settings”, the n reboot system.
Chapter 4 69 Battery can’t be charged See “Check the Battery Pack” on page 59. Battery pack System board PCMCIA-Related Symptom s Symptom / Error Action in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assemb ly System board PCMCIA slot pin is damaged.
70 Chapter 4 NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undete rmined Problems” on page 72. Battery fuel gauge in Windows doesn’t go hig her than 90%. Remove battery pack and let it cool for 2 hours.
Chapter 4 71 Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons th at have nothing to do with a hardware defect, such as: cosmic radiation, electros tatic discharge, or software errors. FRU replacement should be considered only when a recurring prob lem exists.
72 Chapter 4 Undetermined Problems The diagnostic proble ms does not identify wh ich adapter or device failed, which in stalled devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedure s to isolate the fail i ng FRU (do not isolate non-defective FRU).
Chapter 6 73 This chapter gives you the FRU (Field Replaceable Unit) listing in global configura tions of Aspire 3610. Refer to this chapter w henever ordering for p arts to repair or for RMA (R eturn Merchandise Authorization).
74 Chapter 6 Aspire 3610 Exploded Diagram Aspire 3610 FR U List ADAPTER N/A ADAP T ER 65W HIPRO HP- OK066B13WI AP .0650A.005 N/A ADAPTER 65W LITEON P A-1650- 02WE AP .06503.008 N/A ADAPTER 65W DEL T A SADP-65KB DBE AP .06501.007 BA TTERY 21 BA TTERY P ACK LI+ 4CELL 2.
Chapter 6 75 N/A WIRELESS LAN BOARD 802.1 1BG FOXCONN A THEROS EU 54.0309C.01 1 WIRELESS LAN BOARD 802.1 1BG FOXCONNBCM4318 MURA 54.0309D.002 22 BLUETOOTH BOARD WNC BC92035 56.25004.041 BLUETOOTH BOARD FOXCONN BCM2045 56.25020.001 N/A TOUCHP AD BOARD SYNP A TICT M61PUF1G372 56.
76 Chapter 6 7 UPPER CASE W/COVER SWITCH CABLE 60.4E101.001 N/A PCMCIA DUMMY CARD 42.4C518.001 N/A TOUCHP AD BR ACKET 60.4C510.002 5 DIMM COVER 60.4E105.001 N/A HINGE P ACK 15.4" LEFT/RIGHT 6K.4C5CS.001 COMBO Drive 10 COMBO MODULE 24X 65.4E104.001 N/A OPTICAL BRACKET 33.
Chapter 6 77 N/A CDR W/DVD COMBO MODULE 24X PHILIPS SCB5265 W/O BEZEL KO.02403.007 CDRW/DVD COMBO MODULE 24X TOSHIBA TS-L462C W/O BEZEL KO.02404.005 CDRW/DVD COMBO MODULE 24X LITEON SOSC-2483K W/O BEZEL KO.02409.006 CDRW/DVD COMBO MODULE 24X HLDS GCC-4244N W/O BEZEL KO.
78 Chapter 6 FA N 4 FA N 23.10122.001 HARD DISK DRIVE 9 HDD MODULE 40G 65.4E102.001 N/A HDD BRACKET 60.4E107.001 N/A HDD 40G 4200PRM SEAGA TE ST94019A KH.04001.010 HDD 40G TOSHIBA MK4025GAS KH.04004.005 HDD 40G HIT ACHI HTS424040M9A T00 KH.04007.012 HDD 40G WD WD 400UE-00HCT0 KH.
Chapter 6 79 8 LCD MODULE 15" XGA 65.4E106.001 N/A INVERTER BOARD 15.4" DARFON 19.21066.002 N/A LCD BRACKET 15" RIGHT Note: The image displays LCD bracket right and left. 33.4C503.001 N/A LCD BRACKET 15" LEFT Note: The image displays LCD bracket right and left.
80 Chapter 6 N/A LCD 15" XGA LG LP150X08-TLA2 LK.15008 .019 LCD 15" XGA QDI QD150XL06-L3 LK.15009 .008 8 LCD MODULE 15.4" WXGA 65.4E107.01 1 N/A INVERTER BOARD 15.4" DARFON 19.21066.002 N/A LCD BRACKET 15.4" RIGHT 33.4C501.002 N/A LCD BRACKET 15.
Chapter 6 81 N/A SDIMM 512M NANY A NT512T64UH8A0FN-37B KN.51203.018 N/A SDIMM 512M MICRON MT8HTF6464HDY -53EB3 KN.51204.019 N/A SDIMM 512M SAMSUNG M470T6554BZ0-CD5 KN.5120B.008 N/A SDIMM 512M HYNIX HYMP564S64P6-C4 KN.5120G .005 N/A SDIMM 256M MICRON MT8HTF3264HDY -40EB3 KN.
82 Chapter 6 AS1680/AS1410 KEYBOARD DARFON ARABI C TBD KEYBOARD 89KEY DARFON NSK- H3M1A BE 99.N5982.M1A KEYBOARD 89KEY DARFON NSK- H3M0W SD 99.N5982.M0W AS1680/AS1410 KEYBOARD DARFON CZECH TBD KEYBOARD 89KEY DARFON NSK- H3M0Q HG 99.N5982.M0Q KEYBOARD 89KEY DARFON NSK- H3M0N NW 99.
Chapter 6 83 N/A SCREW 86.00D02.230 N/A SCREW 86.9A323.6R0 11 SCREW 86.9A323.8R0 N/A SCREW 86.9A352.3R0 12 SCREW 86.9A352.4R0 N/A SCREW 86.9A353.4R0 14 SCREW 86.9A353.6R0 15 SCREW 86.9A353.8R0 N/A SCREW 86.9A523.3R0 N/A SCREW 86.9A524.4R0 N/A SCREW 86.
84 Chapter 6.
Index 85 A AC Adapter 28 AFLASH Utility 43 Audio 20 B Battery 27 BIOS 20 package 20 ROM size 20 ROM type 20 vendor 20 Version 20 BIOS Supports protocol 20 BIOS Utility 32 Navigating 33 Onboard Device .
86 Index Mechanical S pecificatio n 30 media access on indicator 12 Memory Check 68 Model Definition 1 01 Modem 22 N Notebook Manager hotkey 16 num lock on indicator 12 O Online Support Information 11.
Index 87.
Ein wichtiger Punkt beim Kauf des Geräts Acer 3610 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Acer 3610 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Acer 3610 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Acer 3610 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Acer 3610 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Acer 3610 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Acer 3610 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Acer 3610. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Acer 3610 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
