Benutzeranleitung / Produktwartung IS150 des Produzenten Pelco
Zur Seite of 32
INST ALLA TION C3427M-C (10/07) IS150 Series Camclosure ® Integrated Camera System.
2 C3427M-C (10/07).
C3427M-C (10/07 ) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . .
4 C3427M-C (10/07) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . .
C3427M-C (10/07 ) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C3427M-C (10/07) Description The IS150 Series Camclosure ® integrated camera system combines an environmental cover , back box, camera, lens, and lower dome into a small, high-securi ty system that is quick and easy to install.
C3427M-C (10/07 ) 7 Indoor/outdoor dome, vandal resistant, in-cei ling mount, clear bubble, liner , gray finish PARTS LIST Camera T ype Lens/Iris NTSC P AL Color , Wide Dy namic Range, Day/Night 3-9.5 mm, Day/Night V arifocal, Auto Iris IS151-DWV9 9-22 mm, Day/Night Varifocal, Auto Iris IS151-DWV22 Color , High Resolution, Day/Night 3-9.
8 C3427M-C (10/07) Figure 1. Package Comp onents BA C K BOX (1) C AMERA MODULE (1) TRIM RING, LINER, AND C LEAR BUBBLE (1) TRIM RING AND SMOKED BUBBLE (1) < OR > 1/8-IN C H HOLLOW S C REWDRIVER BIT (1) ADAPTER PLA TE (1) SHOWN A C TUAL SIZE SHIPPING BOX 8-32 X 1.
C3427M-C (10/07 ) 9 Cover and Back Box Installation The IS150 Series Camclosure integrated camera system mounts only into a wall or ceiling. UNSHIELDED T WISTED PAIR (UTP) VIDEO The IS150 Series offers support fo r unshielded twiste d pair (UTP). The UTP video output signal is 1 Vp-p differential into a 100-ohm load.
10 C3427M-C (10/07) SUSPENDED CEILING NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n).
C3427M-C (10/07 ) 11 4S DEEP ELECTRICAL BOX NOTE: Y o u should install the camera module into the back box before installing the back box into the surface. When installing the back box into the surface, rotate the camera modu le to access the mounting holes (refer to Came ra Module on page 12 for more informatio n).
12 C3427M-C (10/07) Camera Module The IS150 Series Camclosure camera modu le includes the camera, came ra bracket, and heate r board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to re move and reinstall the camera module.
C3427M-C (10/07 ) 13 2. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 6). Figure 6.
14 C3427M-C (10/07) CAMERA ORIENTATION At the factory , the camera module is configured for ceiling mounting. For wall mountin g, you must change the camera orientation or the video image could be upside down or sideways. T o change the camera orientation (refer to Figure 7): 1.
C3427M-C (10/07 ) 15 Camera Adjustments T o perform the following camera adjustments, make su re to plug in the camera an d service connectors. Y ou may have to remove the camera module from th e back box. Connect a monitor . Then turn on power to the camera and monitor .
16 C3427M-C (10/07) DN/CH SERIES ADJUSTMENTS Refer to Figure 9 to adjust the IS150-DN or IS150-CH model. Figure 9. Adjusting the I S 150-DN/CH S eries Camclosure SWITCH SETTINGS Locate the DIP switch.
C3427M-C (10/07 ) 17 SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts.
18 C3427M-C (10/07) V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only . When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one came ra to another . T o eliminate vert ical roll, reverse the 24 VAC connec tions on one camera.
C3427M-C (10/07 ) 19 DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation.
20 C3427M-C (10/07) DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 11 to adjust the IS150-DW or IS150-CW model. Figure 11. Adjusting the I S 150-DW/CW S erie s Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation.
C3427M-C (10/07 ) 21 SW1-4: A WB (Auto White Balan ce)/MWB (Manual Whi te Balance) Auto white balance is enabled by defa ult (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white.
22 C3427M-C (10/07) SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation.
C3427M-C (10/07 ) 23 AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS150-DW and IS 150-CW Series Camclosures automatic ally adjust the camera to the auto iris. Auto iris level adjustments are not necessary. V ERTICAL PHASE ADJUSTMENT NOTE: Use this procedure for 24 V AC operation only .
24 C3427M-C (10/07) Camera Positioning Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in Figure 13). NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring.
C3427M-C (10/07 ) 25 Install Liner and T rim Ring 1. Adjust the liner if installed (refe r to Figure 14): a. Align the screw holes in the trim ring with those in the back box to identify the proper liner position. b. Loosen the three Phillips screws located in t he trim ring.
26 C3427M-C (10/07) Service Connector The IS150 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to set up the field of view and focus the camera. Figure 1 5. S ervice Connector Pelco offers two optional items that plug directly in to the service connector .
C3427M-C (10/07 ) 27 T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follo w the directions supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 16): a.
28 C3427M-C (10/07) Specifications GENERAL Pan/T ilt Adjustment Manual Pan 360° T ilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarbonate dome Finish White polyester powder coat trim ri ng with gray polyester powder coat back box Light Attenuation Smoked 1.
C3427M-C (10/07 ) 29 2.42 (6.15) 1.75 (4.45) 3.50 (8.89) 5.48 (13.92) NOTE: VALUES IN PARENTHESES ARE C ENTIMETERS; ALL OTHERS ARE IN C HES. 3.75 (9.53).
30 C3427M-C (10/07).
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment.
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Ein wichtiger Punkt beim Kauf des Geräts Pelco IS150 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pelco IS150 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pelco IS150 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pelco IS150 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pelco IS150 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pelco IS150 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pelco IS150 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pelco IS150. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pelco IS150 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
