Benutzeranleitung / Produktwartung IP3701H-2 des Produzenten Pelco
Zur Seite of 24
INST ALLA TION C2941M-C (6/08) IP3701H-2 Series IP Color Camera.
.
C2941M-C (6/08) 3 Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Open Source Software Notice . . . . . . . . . . . . . . . . . . . . .
4 C2941M-C (6/08) Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water . 6. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
C2941M-C (6/08) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6 C2941M-C (6/08) Description The IP3701H-2 Series is a high resolution , color video camera with a built-in 100 Base-TX network interface for live streaming to a standard Web browser (Microsoft ® Internet Explorer ® or Firefox ® ).
C2941M-C (6/08) 7 Basic System Configurations IMPORT ANT NOTE. PLEASE READ . The network implementation s in this document are shown as general representations only and are not intended to show detailed network topologies.
8 C2941M-C (6/08) Figure 3. Private Network Example Figure 4. S tatic Network Example IF NOT DH C P, C AMERA IS ASSIGNED DEF AUL T IP ADDRESS 192.168.0.
C2941M-C (6/08) 9 Camera Layout Figure 5. Camera Layout RESET BUTTON Use the reset button locate d on the side of t he camera to access the fo llowing modes: T o access one of these modes: 1. Press and hold the reset butto n. The unit starts cycling throug h the modes; hold the b utton for four seconds to access (cycle thro ugh) each mode.
10 C2941M-C (6/08) Installation LENS MOUNTING The camera can be used with a fixed iris, manual iris, or auto iris lens. The camera is factory set for a CS mount lens, but is easily adjusted for a C mount lens.
C2941M-C (6/08) 11 Wiring T ables CAT5 CABLE Connect a Cat5 cable to the RJ-45 network connector . The 8-pin connector includes video and PoE for the camera. PoE (IEEE 802.3af) injects power over the same ca bling that carries the network data, eliminating the need for a separate power supply .
12 C2941M-C (6/08) The following are the recommended maximum distances for 24 VAC applic ations and are calculated with a 10-percent voltage drop. (T en percent is gene rally th e maximum allowable voltage drop for AC-powere d devices.
C2941M-C (6/08) 13 Lens Setup and Focus Procedures VIDEO DRIVE AUTO IRIS LENS 1. Set the lens mode selector switch to AIV . 2. Switch the electronic shutter control (E SC) and automatic gain control (AGC) OFF . 3. Refer to the lens instructions and adjust the l ens for the optimum picture (video output level of 1V p - p ) .
14 C2941M-C (6/08) MANUAL IRIS LENS 1. Set the ESC and AGC switches to ON (default settings). 2. Focus the lens. a. Open the iris fully and set the lens focus to infin ity . b. View an image more than 6.5 ft (2 m) away. c. Focus the image with the back focus adjustment ring (refer to Back Focus Adjustment on page 15).
C2941M-C (6/08) 15 Back Focus Adjustment The back focus adjustment is located at the front of the camera and is accessible from either side of the case. T o adjust the b ack focus: 1. Loosen the two back focus locking screws (one on each side). 2. T urn the back focus ring until the object is in focus.
16 C2941M-C (6/08) Switch Settings Figure 8. DIP S wi tch Default S ettings NOTES: • White indicates the switch setting. • Under most conditions, you will not b e required to set any switches. ì Backlight compensation (BLC) OFF (default setting) : Disables the BLC mode.
C2941M-C (6/08) 17 t Not Used u Extended dynamic range (EDR) OFF (default setting) : Disables the EDR mode. EDR: Enables the EDR mode to help balance a scene wi th a large dynamic range. Use this feature to improve the picture in washed-out areas. This feature adds 12X the dynamic range, but also increases dark area picture noise.
18 C2941M-C (6/08) Dynamic Range and EDR Dynamic range is the ratio between the brightest and darkest parts of an image or scene. A scene that ranges from bright sunlight to deep shadows has a hi gh dynamic range, while indoor scenes with less contrast have a low dynamic range.
C2941M-C (6/08) 19 T roubleshooting Problem Possible Cause Suggested Remedy No video PoE power issue • V erify Cat5 cable connection. • V erify PoE is enabled. • Disconnect the Cat5 cable from the PoE and then reconnect the cable. Power is indicated by the LED.
20 C2941M-C (6/08) Image too light Installation error • V erify DIP switch settings. • Use a service connector to verify camera operation. Connect one end of the service connector to the BNC service connector on the camera. Connect the other end of the service connector to a monitor .
C2941M-C (6/08) 21 Specifications GENERAL Construction Finish Black polyester powder coat Imaging Device 1/3-inch imager Picture Elements IP3701H-2 768 (H) x 494 (V) IP3701H-2X 752 (H) x 582 (V) Sensing Area 6 mm diagonally Horizontal Resolution 480 TV lines Iris Control Electronic/passive Minimum Illumination 0.
22 C2941M-C (6/08) ENVIRONMENT AL Operating T emperature 14° to 122°F (-10° to 50°C) Storage T emperature 14° to 158°F (-10° to 70°C) PHYSICAL Dimensions 4.54" D x 2.64" W x 3.06" H (11.53 x 6.71 x 7.77 cm) Weight (without lens) 1.
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise proved defective in ma terial or wor kmanship for a period of one year afte r the date of shipment.
Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 U S A U S A & Canada T el: (800) 289-9100 Fax: (800) 289-9150 International T el: +1 (559) 292-1981 Fax: +1 (559) 348-1120 www .
Ein wichtiger Punkt beim Kauf des Geräts Pelco IP3701H-2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pelco IP3701H-2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pelco IP3701H-2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pelco IP3701H-2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pelco IP3701H-2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pelco IP3701H-2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pelco IP3701H-2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pelco IP3701H-2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pelco IP3701H-2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.