Benutzeranleitung / Produktwartung 425103 des Produzenten ParaBody
Zur Seite of 40
1 Part # 6739601 Revision: 11/19/98 ASSEMBL Y INSTRUCTIONS 425103 HOME GYM.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the Parabody 425103 Home Gym. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 PA R T # 6729403 6731003 6726902 6723603 6724102 6726003 6725902 6723803 6729602 6727002 6725302 6728002 6725703 6728402 6723103 6726702 6724603 6727603 6728903 6728603 6723203 6725502 6728803 67367.
4 FIGURE 1 STEP 1 • SECUREL Y assemble the LOW ROW/CALF RAISE (2) to the PRESS BASE (18) using two 1/2 X 3" BOL TS (87), two 1/2" W ASHERS (93), and one 1/2" LOCK NUT (94). • Insert two 1/2" FLANGE BEARINGS (78) into the SWIVEL PULLEY BRACKET (30) as in FIGURE 1.
5 FIGURE 2 STEP 2 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 4 1 93 94 • LOOSEL Y assemble the REAR UPRIGHT (4) to the BASE (1) using two 1/2 X 3” BOL TS (87), two 1/2” W ASHERS (93), and two 1/2” LOCK NUTS (94) as shown in FIGURE 2.
6 FIGURE 3 STEP 3 • SECUREL Y assemble three 4-1/2” PULLEYS (43) to the upper flats on the BASE (1) using three 3/8 X 2” BOL TS (84), six 3/8” W ASHERS (91), three 2-7/8” L-BRACKETS (44), and three 3/8” LOCK NUTS (92).
7 FIGURE 4 STEP 4 • LOOSEL Y assemble the FRONT (25) & MIDDLE UPRIGHTS (8) to the BASE (1) using four 1/2 X 4” BOL TS (88) and four 1/2” LOCK NUTS (94) as shown in FIGURE 4.
8 FIGURE 5 STEP 5 • LOOSEL Y assemble the PRESS BASE (18) to the BASE (1) using two 1/2 X 4” BOL TS (88), two 1/2” W ASHERS (93), and two 1/2” LOCK NUTS (94).
9 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 7 STEP 7 • LOOSEL Y assemble one 4-1/2” PULLEY (43) to the T OP BOOM (17) using one 3/8 X 2-3/4” BOL T (85), two 3/8” FLANGE SP ACERS (49), and one 3/8” LOCK NUT (92).
10 FIGURE 9 STEP 9 FIGURE 10 • Insert two WEIGHT PLA TE BUSHINGS (79) into the “P ARABODY” side of each of the fifteen WEIGHT PLA TES (105) as shown in FIGURE 10.
11 FIGURE 1 1 STEP 1 1 • Insert two GUIDE RODS (36) into the BASE (1) as shown on FIGURE 1 1. (NOTE: Lubricate GUIDE RODS (36) with silicon or teflon spray available at most hardware stores.
12 STEP 12 • LOOSEL Y assemble the T OP BOOM (17) to the top of the MIDDLE (8) & FRONT UPRIGHT (25) using four 3/8 X 2-3/4” BOL TS (85) and four 3/8” LOCK NUTS (92).
13 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 13 • LOOSEL Y assemble the T OP BOOM (17) to the top of the REAR UPRIGHT (4) using two 1/2 X 4” BOL TS (88) two 1/2” W ASHERS (93) and one 1/2” LOCK NUT (94).
14 FIGURE 14 STEP 14 FIGURE 15 STEP 15 • SECUREL Y assemble the PEC SEA T ADJUST (8) to the PEC SEA T (5) using two 1/2 X 3” BOL TS (87), two 1/2” W ASHERS (93) and two 1/2” LOCK NUTS (94). See FIGURE 14. • SECUREL Y attach one 3/4” SQ. RUBBER BUMPER (97) to the PEC SEA T (5) as shown in FIGURE 14.
15 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 16 STEP 16 • Assemble two ROLLER P ADS (37) to the PEC SEA T (5) using two ST ARLOCK COLLARS (50). See FIGURE 14. • Pull back the SPRING PIN (51) on the FRONT UPRIGHT (25) and insert the PEC SEA T (5) down to the desired height.
16 FIGURE 17 STEP 17 • SECUREL Y assemble one 3/8” SPRING PIN (51) to the ROLLER P AD ADJUST (11) as shown in FIGURE 17. • Insert two 1/2” FLANGE BEARINGS (78) into the LEG CURL/EXT (15) as shown on FIGURE 17. • Slide ROLLER P AD ADJUST (1 1) over the LEG CURL/EXT (15) until the spring pin pops into the holes.
17 FIGURE 18 STEP 18 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Insert the PUSH/PULL CABLE through the bottom of the PRESS ARM (27) up to the CONTROL LEVER (60) and hold in place with one E-RING (56) as shown in FIGURE 18. • SECUREL Y assemble the PUSH/PULL CABLE to the CONTROL LEVER (60) using one 3/8” JOINT CONNECTOR CAP (57), one #8 INT .
18 FIGURE 19 STEP 19 • Insert two 3/4” FLANGE BEARINGS (76) into the COUNTER LEVER (3) as shown in FIGURE 19. • Hold the COUNTER LEVER (3) between the REAR (4) and MIDDLE UPRIGHTS (8) and slide the 3/4 DIA X 1 1” SHAFT (107) throught the MIDDLE UPRIGHT (8), COUNTER LEVER (3), and through the collar on the REAR UPRIGHT (4).
19 FIGURE 20 STEP 20 • CAREFULL Y slide the PRESS ADJUSTMENT TUBE (22) into the RECEIVING TUBE (13). (NOTE: Make sur e the spring pin barrel on the RECEIVING TUBE (13) is on the same side as the holes in the PRESS ADJUSTMENT TUBE (22).
21 FIGURE 22 STEP 22 • Insert two 3/4” FLANGE BEARINGS (76) into the PRESS ARM (27) as shown in FIGURE 22. • Hold the PRESS ARM (27) between the REAR (4) and MIDDLE UPRIGHTS (8) and slide the 3/4 DIA X 11” SHAFT (107) throught the MIDDLE UPRIGHT (8), PRESS ARM (27), and through the collar on the REAR UPRIGHT (4).
22 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 23 • SECUREL Y assemble the SPRING PIN ASSEMBL Y of the PUSH/PULL CABLE to the SPRING PIN BARREL on the RECEIV - ING TUBE (13).
23 STEP 26 • SECUREL Y assemble one 3/8” X 1” BUTTON HEAD CAP SCREW (96) and one 3/8” LOCK NUT (92) to the last hole on the BACK P AD ADJUST (16). See FIGURE 26. FIGURE 26 • SECUREL Y insert one 2” SQ. END CAP (46) to the open end of the BACK P AD ADJUST (16).
24 FIGURE 27 STEP 27 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 28 STEP 28 • LOOSEL Y assemble two 3-1/2” PULLEYS (42) to the CENTER PULLEY BRACKET (26) using two 3/8 X 2” BOL TS (84), two 2-3/8” L-BRACKETS (45), four 3/8” W ASHERS (91), and two 3/8” LOCK NUTS (92).
24 FIGURE 28 STEP 28 • Assemble one 3/4” SLEEVE BEARING (77), one PEC CAM (24), two 3/4” FLANGE BEARINGS (76), one 1/2” W ASHER (93), and one 1/2” LOW HEIGHT LOCK NUT (95), and a LEFT (19) or RIGHT PEC ARM (20) to each threaded shaft on the BEARING HOUSING (6).
25 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 29 STEP 29 • Attach two 1 X 1" GUIDES (53) to the PRESS SWIVEL (10) approximately where shown in FIGURE 29. • SECURE PRESS SWIVEL (10) to the post on the CALF/LOW ROW (2) using one ST ARLOCK COLLAR (50).
26 STEP 30 • SECUREL Y assemble one 3/8” SPRING PIN (51) to the spring pin housing of the PRESS BACK SUPPOR T (23). (NOTE: T ighten the nut of the SPRING PIN ASSEMBL Y SECUREL Y .) • SECUREL Y assemble two 3” WHEELS (63) using two BLACK 3/8 X 2-1/2” SOCKET HEAD CAP SCREWS (64) and two 3/8” HEX NUTS (108) as shown in DET AIL 30.
27 FIGURE 31 STEP 31 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECUREL Y assemble one 1/2” SPRING PIN ASSEMBL Y (52) to the spring pin housing on the PRESS SUPPOR T TUBE (21).
28.
29 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 32 STEP 32 • T o assemble the D-RING CABLE (102) follow the cable r outing as shown and use the following steps: • Screw one of the threaded ends of the D-RING CABLE (102) approximately 1” into the end of the SELECTOR SHAFT (73) of the HEAD PLA TE (72) as shown in FIGURE 32.
30 STEP 33 FIGURE 33 • T o assemble the LA T CABLE (99) follow the cable routing as shown and use the following steps: • Remove the two bolts in the FRONT UPRIGHT (25) and TOP BOOM (17) connection. • Route the LA T CABLE (99) as shown in FIGURE 33.
31 STEP 35 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • T o assemble the PRESS CABLE (100) follow the cable routing as shown and use the following steps: • Route the PRESS CABLE (100) around pulleys and L-brackets as shown in FIGURE 35.
32 FIGURE 36 STEP 36 • Run the PRESS CABLE (100) through the hole in the D-RING (7) as shown in FIGURE 36 and attach one KEYHOLE CLEVIS (66) to the end of the PRESS CABLE (100).
33 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 38 STEP 37 • Assemble one 3-1/2” PULLEY (42) around the PEC DEC CABLE (98) and to the PULLEY BRACKET (29) using one 3/8 X 2” BOL T (84), two 3/8” W ASHERS (91) and one 3/8” LOCKNUT (92) as shown in FIGURE 37.
34 DET AIL 39 FIGURE 39 SEE DET AIL 39 STEP 39 • Securely assemble the ball end of the AB CABLE (103) and one 3-1/2” PULLEY (42) to the FRONT UPRIGHT (25) using two 3/ 8 X 2-3/4” BOL TS (85), two 3/8” FLANGE SP ACERS (49), two 3/8” W ASHERS (91), and two 3/8” LOCKNUTS (92).
35 STEP 41 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • T o assemble the LEG CABLE (101) follow the cable routing as shown and use the following steps: • SECUREL Y attach the LEG CABLE (101) to the LEG CURL/EXT (15) using one 3/8 X 1-1/4” BOL T (83), one 3/8” W ASHER (91), and one 3/8” LOCK NUT (92).
FIGURE 43 STEP 43 • Attach three TENSION CORDS (69) to the three KEYHOLE CLEVIS (66) using three CLEVIS PINS (67) and three COTTER PINS (68) as shown in FIGURE 43.
37 STEP 44 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Attach each TENSION CORD (69) to the corresponding small tube on the TOP BOOM (17) using three 1/4” CAP NUTS (55) as shown in FIGURE 44.
• If upon completion of assembly , the HEAD PLA TE (72) does not sit on top of the first WEIGHT PLA TE (105), push the HEAD PLA TE (72) down, insert the WEIGHT ST ACK PIN (75) and perform several repetitions at the press station. This will relax the cable system and prevent the HEAD PLA TE (72) from lifting up.
39 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 48 FIGURE 48 FIGURE 47 STEP 47 • SECUREL Y attach the top of the front SHROUD (31-with label) & rear SHROUD (31) to the T OP BOOM (17) using four 3/8” X 1” BUTTON HEAD CAP SCREWS (96). See FIGURE 47.
40 STEP 49 FIGURE 49 • Attach the LA T BAR (28) to the ball end of lat cable using one 5/16” SNAP LINK (54). • Attach the AB CRUNCH STRAP (82) to the ball end of cable using one 5/16” SNAP LINK (54).
Ein wichtiger Punkt beim Kauf des Geräts ParaBody 425103 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ParaBody 425103 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ParaBody 425103 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ParaBody 425103 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ParaBody 425103 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ParaBody 425103 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ParaBody 425103 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ParaBody 425103. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ParaBody 425103 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
