Benutzeranleitung / Produktwartung WV-NW474S des Produzenten Pantech
Zur Seite of 58
Model No. W V -NW474 S Col o r CCTV C a mer a Operating Instruction s Before attempting to connect or operate this product , please read these instructions carefully and save this manual for future use . RHP International - www.Rock2000.com Toll Free: 1-888-919-2263 Outside the U.
-2- WARNING: To prevent fire or electric shock hazard, do not expose this appliance to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
-3- IMPORT ANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings.
-4- CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................... 3 PREFACE .................................................................... 5 Features ................................................................... 5 System Requirements .....
-5- Features • 10/100BASE-T terminal enabling you to view camera images via the network • User/Host authentication • SD-II (Super Dynamic) expands the dynamic range up to 46 dB without interference between dark and bright portions in a scene.
-6- • Ethernet is a registered trademark of Xerox Corporation. • Other names of companies and products contained in these operating instructions may be trademarks or registered trademarks of their respective owners.
-7- 1. This product should be installed and connected in conformity with NEC by qualified service per- sonnel or system installers. 2. Use a class 2 power source supplying 24 V AC. 3. To prevent fire or electric shock hazard, use a UL listed cable (VW-1, style 1007) to connect the power supply to the camera.
-8- MAJOR OPERA TING CONTROLS & THEIR FUNCTIONS A B L E F T R IG H T U P D O W N S E T LINK LED OFF LED ON RCV A B L EFT R IG H T U P D O W N S E T LINK LED OFF LED ON RCV u i o !0 !1 !2 !3 !4 !5 !6 !7 !9 !8 t r q y w T ranspor t Protection Screws (Red) e q Tilting lock screw Fixes the tilting position.
-9- !7 Set button (SET) Validates the selection or opens a detailed menu. !8 DIP switch Specifies certain settings shown in the figure. The default setting is marked with an asterisk *. Note: The settings will be applied to the camera only when DIP SW, not MENU, is selected in the menu setup.
An example of flush mounting is shown. This example shows two boxes: one is for camera mounting and the other is for cable junction. 1. Procurement • Four screws Locally procure four bracket fixing screws suitable for the installation surface and structure of the wall/ceiling or junction box.
-11- ■ Mounting the Camera Disassembling the Camera 1. Remove the dome cover by loosening the three tamper-proof screws with the supplied bit. 2. Remove the two red-colored screws provided for transport protection with a Philips screwdriver. Optional Heater Unit Assemble the optional heater unit into the camera if necessary.
● Power Connection Use individual power sources for the camera and optional heater unit. • Wire colors & functions -12- ■ Connections Cautions: • This product should be installed and connected in conformity with NEC by qualified service personnel or system installers.
-13- ● Video Output Connection Connect the video output cable to the monitor or other system device with the procured coaxial cable. The maximum extensible length is shown in the table. ● Control Connector Connect the respective peripherals to supply and receive control signals.
-14- 3. Zoom • Unlock the zoom lever. • Move the lever to adjust the zoom. • Lock the lever. 4. Focus • Unlock the focus lever. • Move the lever to adjust the focus. • Lock the lever. 5. Reinstalling the dome cover • Attach the dome cover to the camera so that the two position marks match.
● Connection to Internet (Type 3) The PC accesses the camera through the Internet and the DSL/CATV modem. Necessaries: • Straight-type network cable (Category 5) • CATV modem (cable modem) or DSL modem ● Connection to Internet (Type 4) A switching hub or a router may be added to type 3 connection.
-16-.
-17- CAMERA SETUP PROCEDURES.
-18- ■ Network Setup of Y our PC To set up the network of the PC, first change the TCP/IP settings of the PC to match them to the default settings of the camera. The following are the default network settings of the camera. IP address : 192.168.0.10 Subnet mask : 255.
-19- 7. Click the "Use the following IP address" radio button and enter the IP address and the subnet mask as follows. IP address : 192.168.0.
-20- 5. Click the [Enable] button when using DHCP and DNS. When using the DNS functions, enter the "Primary DNS Server address" and the "Secondary DNS Server address". 6. Click [AUTO] when the DNS server gets primary and secondary IP addresses from the DHCP server.
-21- 6. Click the [Network] button. The "Network Setup" window appears. 7. Enter parameters for each item in the columns. Refer to Network Setup Parameters vs. Connection Type. Notes: • After clicking the SET & REBOOT button, the browser software stops refreshing images and displays a dialog box prompting you to restart.
-22- ■ Network Setup Parameters vs. Connection T ype Connection type Item Parameter description Connection type 1 IP address Enter "192.168.0.XXX" (where XXX should be a number from 2 to 254 except the same IP addresses already assigned to the PC or any other cameras).
-23- Connection type Item Parameter description Connection type 3 IP address Enter the IP address assigned by your Internet service provider. The setting is not required if your Internet service provider uses a DHCP server (the DHCP server assigns an IP address to the camera automatically).
-24- Connection type Item Parameter description Host name Contact your Internet service provider and enter the assigned host name if required. Network speed Select the network speed by pressing the [ o ] button.
-25- This section describes the camera setup procedures common to accesses from the PC and from the camera. ■ Buttons Used for Setup Press the buttons inside the camera, or click the but- tons on the computer display. Each button is assigned functions in the setup as follows.
-26- 4. Click the Menu ON button to overlay the ** SET UP ** menu on the camera image. The cursor is highlighted on the window. 5. Move the cursor to SETUP DISABLE if it is dis- played, or skip to step 7 if ENABLE is displayed. 6. Click the SET button.
-27- ■ Setup Menu T ree ** SET UP ** ** CAM SET UP ** ALC CAMERA ID ↵ AGC SHUTTER SYNC SENSE UP MO TION DET WHITE BAL CAMERA ID ** ALC CONT ** MASK SET ↵ ** A WC ** ** MO TION DETECT ** CHROMA G.
Opening the camera setup menu ■ Camera Setup Menu (CAM SETUP) 1. Camera Identification (CAMERA ID) Setting You can assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on and off on the monitor screen.
-29- To edit the CAMERA ID 1. Move the cursor to CAMERA ID. The factory default setting is OFF. 2. Press [SET]. The CAMERA ID menu appears. The cursor on the letter “ 0 ” is highlighted. 3. Move the cursor to the character you want to edit by pressing [Left]/[Right]/[Up]/[Down].
-30- 3. Move the cursor to the area where backlight is bright and press [SET] to mask that area. The mask turns to white. (When the cursor is moved on an area that has already been masked, the mask and cursor start blinking.) 4. Repeat step 3 to mask the desired areas.
-31- 6. Synchronization Setting (SYNC) There are three synchronization modes: INT (internal), LL (line-lock), and VD2 (vertical drive). You can select the internal or line lock mode in the menu setup, but you cannot select VD2. The VD2 signal is supplied from an external device e.
-32- • Automatic White Balance Control Mode (AWC) In this mode, accurate white balance is obtained within a color temperature range of approximately 2 300-10 000 K. 1. Move the cursor to WHITE BAL and select AWC → PUSH SW. 2. Press [SET] to start white balance setup.
-33- • The camera will deactivate the detector for a few minutes after the power of the camera is turned on or the BW setting in the Special Menu is set to something other than OFF. • The motion detection function is not designed specifically for prevention of theft, fire, etc.
-34- 5. Press [Up] or [Down] to zoom in or out the image. 6. Move the cursor to PUSH SET for PAN/TILT and press [SET]. The PAN/TILT setting menu appears. 7. Press [Up] or [Down] [Left] or [Right] to change the angular field of view. 8. To return to the EL-ZOOM setting menu, press [SET].
-35- ■ Network Setup (NETWORK SETUP) Set up network parameters when connecting the 10/100BASE jack with a network. Notes: • Access the setup menu from the PC to use the DHCP or DNS server, because these settings are not included in this window.
-36- There are nine menu buttons in the Setup Menu tab. As described earlier the Camera menu is operable from both the camera and the PC. Contrary to that, the remaining eight menus are accessible only from the PC.
-37- ■ Alarm Setup 1. Open the Alarm Setup window. 2. External Alarm • Select ON or OFF for External Terminal Input, and click the [SET] button. ON: Receives alarm inputs via the ALARM IN termi- nal. OFF: Ignores alarm inputs via the ALARM IN termi- nal.
-38- • Click the [SET & REBOOT] button. Note: Wait for around 10 seconds until rebooting is completed. Note: Sending E-mails will not be possible in an envi- ronment where POP (Post Office Protocol) authenti- cation is required. 7. External Alarm Reset • Click the [Alarm Reset] button to cancel the activat- ed alarm.
-39- ■ User Setup 1. Open the User Setup window. 2. User Registration • Enter the user name in up to 16 characters. The default setting is "admin". Only one administrator is necessary. • Enter the password. The default setting is a blank.
-40- ■ System Setup 1. Open the System Setup window. 2. Time Adjustment • Select MANUAL or NTP and click the [SET] button. MANUAL: Calibrates the time manually. NTP (Network Time Protocol): Calibrates the time using your network system. The respective window appears.
-41- OPERA TING PROCEDURES.
-42- You can reset the following data back to the factory default settings. Camera Setup Setup Menu (PC oriented) HTML files ■ Initializing the Camera Menu • Move the cursor to CAMERA RESET. • Hold down [Left], [Right], and [SET] buttons simulta- neously for 2 seconds on the camera, or click the All Reset button on your computer display.
-43- You can operate the camera in two ways: with the PC by way of network, or with such system devices as the Video Multiplexers and System Controllers. ■ Operating from System Devices Electric zoom, zoom position move, and iris control are operable with the system devices.
-44- ■ Preparations for Network Access 1. Start up the PC. 2. Start up the Web browser, Internet Explorer or Netscape Communicator. 3. Enter the IP address of the camera in the address bar. The factory default for the camera address is 192.168.0.10.
-45- ■ Windows Explanation ● Main Window q Camera Adjustment button Opens the camera adjustment window. w Alarm List button Opens the alarm list (event history) in the left half of the window. e Setup Menu button Opens the index buttons, each of which opens respective menu setup, in the left half of the window.
-46- ● Camera Adjustment Window !2 !3 !4 !5 !6 u Go to Main Menu button Returns to the main menu. i Multi Screen Select buttons [1]: Displays a single camera image, returning from a quad split image. [1-4]: Displays a quad split image comprising cam- era 1 to camera 4.
■ Still Picture Storage to the PC The camera picture can be saved as a still image on your PC. 1. Move the cursor to the picture area on the screen, and right-click to select "Save As". 2. Enter a file name to be assigned to the picture, and specify the storage place in the dialog box.
-48- When an alarm sounds, the camera performs output functions depending on the setup. Inputs: • The alarm sensor connected to the ALARM IN termi- nal on the camera • The built-in VMD (Video Moti.
-49- • A mail can be sent to a maximum of four addresses, with or without attached picture file. A mail contains: the camera name, time & date of occurrence, cause of event, and the reference addresses to the stored pictures as follows. The number of stored alarm pictures: e.
-50- 3. Move the cursor to CAMERA and click SET. ** CAM SET UP ** appears. 4. Move the cursor to MOTION DET and turn it to ON with the right or left button, and click the [SET] but- ton. ** MOTION DETECT ** appears. 5. Move the cursor to MASK SET, and click the [SET] button.
-51- ■ Reviewing Alarm Pictures The alarm pictures stored in the camera can be reviewed on the PC. 1. In the main window, click the [Alarm List] button. Causes of events are abbreviated in the Type col- umn. TRM: Caused by the input supplied via the Alarm-In connector.
-52- ■ Resetting Alarm You can reset the alarm output functions being activat- ed. 1. In the main window, click the [Setup Menu] button. 2. Click the [Alarm] button to open the Alarm Setup window. 3. Scroll down the screen. 4. Click the [Alarm Reset] button.
-53- ■ Customizing Alarm Notice E-Mail You can customize the contents of e-mails notifying the recipient of alarm events and their dates. Take the following steps: Step 1 Create an alarm e-mail as shown below using any text editor, and save it as "almmail.
-54- TROUBLESHOOTING Symptom No picture is displayed. HTML documents are not displayed. • Is the AC adapter firmly plugged in to the outlet? • Are the POWER IN terminals on the camera connected with the AC adapter properly? • Is the video cable or network cable connected properly? • HTML files in the camera might be broken.
-55- When the camera is aimed at a bright light, such as a spotlight, or a surface that reflects bright light, smear or blooming may appear. Therefore, the camera should be operated carefully in the vicinity of extremely bright objects to avoid smear or blooming.
-56- Control Function: Auxiliary Out: Collector-output, OFF (Open or 4 V DC – 5 V DC)/ ON ( ≤ 1 V 50 mA) Day/Night In: Pulled-up to 5 V DC, OFF (Open) / ON (0 V 0.
-57- ■ Optional Heater Unit WV -CW3H ● Introduction Installing this heater unit enables the camera to operate under in a low-temperature environment of – 30 ° C ( – 22 ° F). The heater turns on automatically when the temperature inside the camera drops below +10 ° C (50 ° F) and turns off when it rises.
PANASONIC CANADA INC. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 PANASONIC SALES COMPANY DIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.
Ein wichtiger Punkt beim Kauf des Geräts Pantech WV-NW474S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pantech WV-NW474S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pantech WV-NW474S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pantech WV-NW474S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pantech WV-NW474S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pantech WV-NW474S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pantech WV-NW474S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pantech WV-NW474S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pantech WV-NW474S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
