Benutzeranleitung / Produktwartung AG-DV2500P des Produzenten Panasonic
Zur Seite of 68
Model AG-DV250P Digital Video Cassette Recorder Before operating this product, please read the instructions carefully and save this manual for future use. LLT0029-001A Printed in Thailand VQT0C54 P Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 © 2003 Matsushita Electric Industrial Co.
E-2 1. Read all of these instructions. 2. Sav e these instructions for later use . 3. All warnings on the product and in the operating instructions should be adhered to . 4. Unplug this appliance system from the wall outlet bef ore cleaning. Do not use liquid cleaners or aerosol cleaners.
E-3 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
E-4 Thank you f or purchasing our Digital Video Cassette Recor der AG -D V2500P . This VTR features dual support for NTSC and P AL. Certain functions howe ver , are supported by only one signal system. They are indicated with (NTSC only) or (P AL only).
E-5 TABLE OF CONTENTS INTRODUCTION Precautions .................................................... 6 Daily maintenance and regular inspection ..... 7 Precautions on the use of cleaning tape ........ 8 Cassette tape ...................................
E-6 INTRODUCTION Precautions 䡵 Place of storage and use Please av oid storing or using this VTR in the fol- lowing places: ● Extremely hot or cold places beyond the al- lowab le temperature for operation (5˚C – 35˚C). ● Humid or dry places beyond the allow able humidity range f or operation (30% –80% RH).
E-7 Daily maintenance and regular inspection This unit uses consumables or components that will w ear off. If a worn-out or deteriorated component continues to be used, it ma y cause the unit to break down. T o pre vent this , please perform daily mainte- nance using the head-cleaning tape.
E-8 INTRODUCTION Precautions on the use of c leaning tape Please use cleaning tape produced by P ANASONIC . Please f ollow the instructions below when using the cleaning tape. 1. The tape will run for 10 seconds in the PLA Y mode. (Thereafter , it stops automatically and enters the ST OP mode.
E-9 Head drum Videotape Condensation ● When this unit is mov ed from a cold to a warm place abruptly , the vapor in the warm air will come into contact with the head drum or the tape guides. When chilled, the vapor turns into drop- lets of water . This state is known as condensa- tion.
E-10 EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC D VCAM PA USE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 2 43 1 1 [PO WER] Po wer button/LED ● Press this button to turn on the power and op- erate the unit.
E-11 EJECT MENU REW SET FF PLA Y STOP REC INH. PA L AUDIO NTSC D VCAM PA USE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 5 6 7 5 [REMO TE] Remote select switch Use this s witch to select the remote controller type.
E-12 NAMES AND FUNCTIONS OF V ARIOUS P ARTS – Front panel – (continued) 8 [REC] Record b utton/LED ● Hold down this b utton and press the 9 PLA Y b utton to start recording. During recording, the LED lights up red. ● Hold down this button and press the 0 PA USE b utton to pause the recording.
E-13 $ Indicator :W hen a cassette is loaded, the LED lights up green. (Like wise when the unit is in the POWER OFF state .) When a cassette is being loaded or ejected, the LED blinks . D VCAM : When the unit pla ys back a tape re- corded in the D VCAM format, the LED lights up green.
E-14 NAMES AND FUNCTIONS OF V ARIOUS P ARTS – Rear panel – 1 DC power input terminal (2P) This is used for DC12V input. It connects the DC mains cable of the pro vided AC adapter . Memo ● When power is supplied to this terminal, the POWER indicator located at the front panel lights up.
E-15 DV IN/OUT AUDIO VIDEO CH 1/3 CH 2/4 LINE S -VIDEO N I O U T 9PIN REMOTE AUX NTSC PAL DC 12V W ARNING : SHOCK HAZARD - DO NOT OPEN. A VIS : RISQUE DE CHOC ELECTRIQUE - NE P AS OUVRIR. !6 5 87 9 0 9 [A UDIO IN] Audio input terminal (PHONO 2) This is the audio signal (analog) input terminal.
E-16 NAMES AND FUNCTIONS OF V ARIOUS P ARTS – Wir eless remote contr oller – DISPLA Y B ARS MENU SEARCH+ SEARCH– A.DUB F. REV INDEX – INDEX + PLA Y STOP VEQ3533 REW FF PA USE SET BLANK STILL MODE VCR POWER /I A UDIO MUTING OUT SEL. OUT LEV . REC F.
E-17 [SEARCH–] / button • During playbac k, STILL mode or variable speed pla yback in the f orward direction, press this button to slo w down the pla yback speed. • During rev erse pla yback or v ariable speed pla yback in the re verse direction, press this b utton to speed up the pla ybac k speed.
E-18 ON-SCREEN DISPLA Y – Regar ding on-screen display – Besides E-E images and playbac k images, the monitor connected to the VIDEO LINE OUT terminal and S- VIDEO OUT terminal provides the follo wing on-screen information. DISPLA Y BARS MENU SEARCH+ SEARCH– A.
E-19 ON-SCREEN DISPLA Y – Status display – 䡵 Status displa y: It displays the current settings and oper ating status. 32 K C H – 1/2 0 mi n 10 / 10 / 02 STA N DB Y - OF F 12 : 00 : 00 T C R 0 2:0 0:0 0:0 0 1 2 No.
E-20 ON-SCREEN DISPLA Y – Status display – (continued) No. Item Content 3 Time code • It displa ys the time codes (hour , minute, second and frame).
E-21 A UDIO MUTING ON A UDIO MUTING OFF A UDIO OUT LEVEL NORM A UDIO OUT LEVEL A TT A UDIO OUT CH-1/2 A UDIO OUT CH-3/4 A UDIO OUT MIX DISPLA Y ON DISPLA Y A UT O DISPLA Y OFF FIELD STEP 1ST FIELD STI.
E-22 ON-SCREEN DISPLA Y – Alarm display – 䡵 Alarm display : Alar m messages are display ed as shown belo w , when an operation error has occurred or when the unit is in a poor condition f or operation. E.g., dir ty head. Display Contents LO W V OL T A GE HEAD CLEANING REQUIRED! NO D V SIGNAL The voltage of the DC input po wer is low .
E-23 Display Contents COPY INHIBIT REC INHIBIT A. DUB INHIBIT (REC T AB) A. DUB INHIBIT (48K) A. DUB INHIBIT (LP) A. DUB INHIBIT (BLANK) A. DUB INHIBIT (D V) A. DUB INHIBIT (NTSC/P AL) A. DUB INHIBIT (D VCAM) The user attempts to record signals protected with the cop y guard.
E-24 PREP ARA TION – Provided wir eless remote contr oller – Loading the batteries Bef ore using the wireless remote controller , please load 2 batter ies (AA) in. 1 Lift up the cover of the battery compartment. 2 Load in 2 batteries (AA). • Please inser t the · pole in first.
E-25 Using the wireless remote contr oller Maximum distance to the sensor of the unit : 6m Angle : within 30˚ EJECT MENU REW SET FF PLA Y STOP REC INH.
E-26 PREP ARA TION – Power – Connect the provided A C adapter to the main unit. DV IN/OUT A UDIO VIDEO CH 1/3 CH 2/4 LINE S -VIDEO N I O U T 9PIN REMOTE AUX NTSC PAL DC 12V W ARNING : SHOCK HAZARD - DO NOT OPEN. AV I S : RISQUE DE CHOC ELECTRIQUE - NE P AS OUVRIR.
E-27 Switching on the po wer REW PLA Y STO REC INH. PA L AUDIO NTSC DVCAM POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500.
E-28 PREP ARA TION – Selecting the NTSC/P AL signal system – This unit suppor ts both the NTSC and P AL signal system. Bef ore inputting analog signals (composite or YC separate video signals), please select the signal system.
E-29 PREP ARA TION – Loading/ejecting cassettes – Please use standard D V cassettes or mini D V cassettes. Loading the cassette 1. Check the cassette. • Set the rear slide. Push it to “REC” for recording or “SA VE” to prev ent lighted con- tents from being erased accidentally .
E-30 PREP ARA TION – Setting/displaying date and time – This function sets up the date and time data of the b uilt-in clock. With the built-in chargeab le battery , the configured date and time data is maintained e ven after the main po wer is turned off .
E-31 EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC DVC A M PA USE REC CH 1 / 3 2 / 4 EJECT button PLA Y button ST OP button REW button PA USE button FF button DISPLA Y B ARS MENU SEARCH+ SEARCH– SET BLANK STILL MODE VCR POWER /I A UDIO MUTING OUT SEL.
E-32 Selecting date/time displa y The date and time inf ormation is displayed on the monitor screen connected to the VIDEO LINE OUT or the S-VIDEO terminal. T o set whether to display the date and time inf or mation and the displa y style, use the DISPLA Y menu screen.
E-33 DV IN/OUT AUDIO VIDEO CH 1/3 CH 2/4 LINE S -VIDEO N I O U T 9PIN REMOTE AUX NTSC PAL DC 12V W ARNING : SHOCK HAZARD - DO NOT OPEN. AV IS : RISQUE DE CHOC ELECTRIQUE - NE P AS OUVRIR.
E-34 EJECT MENU REW SET FF PLA Y STOP REC INH. PA L AUDIO NTSC DVCAM PA USE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 NTSC indicator P AL indicator INPUT switch N/OUT DIO VIDEO CH 2/4 LINE S -VIDEO N I O U T 9PIN REMOTE AUX NTSC PAL DC 12V N G : SHOCK HAZARD - DO NOT OPEN.
E-35 RECORDING – Setting time codes – This unit has a built-in time code reader/ gener ator . During recording, time codes are re- corded. During recording of data from the built-in time code generator , the user-bits are not recorded.
E-36 ––– M E N U ––– SY STE M . . RE M OT E . . AUD I O / V I DEO . . TI M E C O D E. . DIS P L A Y S E T . . CLO C K ADJUST . . FA CT O RY S ET TIN G CANCE L DR UM HO UR ME TE R 000000 H EX I T T op MENU –––T IM E C O D E––– TC 0 0:0 0:0 0:0 0 CLEA R CANCE L ND F / DF ( N T SC ) DROP DV TC DUP .
E-37 RECORDING – Recor ding method – Main unit Remote controller EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC D VCAM PA USE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 PA USE button ST OP button PLA Y button REC button A.
E-38 RECORDING – Series r ecording function – By linking this unit to other D V devices, this unit can perf or m continuous, long-hour recording. This unit can be set as a backup unit connected to a D V camcorder . When the recording tape of the source unit ends, this unit can start recording.
E-39 RECORDING – Audio dubbing – A.DUB F. REV INDEX – INDEX + PLA Y STOP VEQ3533 REW FF PA USE REC F. AD V PLA Y button PA USE button ST OP button A.DUB button EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC D VCAM PA USE POWER REC A.
E-40 RECORDING – Audio dubbing – Memo • During audio dubbing, if the tape comes to a par t recorded in a non dubbing-f easible mode (such as LP mode or 48kHz audio mode), the VTR will enter the ST OP mode. When this happens , high- v olume noise from the D V output will occur .
E-41 PLA YBACK – Connection/setting – This section e xplains the required connection, setting and operation method f or using this unit as a pla yer . Connection 䡵 Using this unit as a standalone device DV IN/OUT AUDI O VIDEO CH 1/3 CH 2/4 LINE S -VIDEO N I O U T 9PIN REMOTE AUX NTSC PAL DC 12V W ARNING : SHOCK HAZARD - DO NOT OPEN.
E-42 Setting 䡵 REMO TE switc h on the front panel To use the wireless remote controller, set the s witch to “WIRELESS”. 䡵 SYSTEM menu • STILL MODE Use this to select the image type f or still image playbac k or frame advance pla yback.
E-43 PLA YBACK – Basic playback method – EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC D VCAM PA USE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 PA USE button ST OP button PLA Y button REW button D VCAM indicator FF button A.
E-44 PLA YBACK – Special playback function – Frame adv ance (reverse) pla yback Use the remote controller . DISPLA Y B ARS MENU SEARCH+ SEARCH– A.DUB F. REV INDEX – INDEX + PLA Y STOP VEQ3533 REW FF PA USE SET BLANK STILL MODE VCR POWER /I A UDIO MUTING OUT SEL.
E-45 V ariable speed pla ybac k Use the remote controller . Set the unit to the searc h mode. The main unit button can also be used to set the unit to the search mode. 1. Set the unit to the PLA YB A CK or the STILL mode. 2. Press the FF button to e xecute fast-f orward pla yback.
E-46 PLA YBACK – Locate function – Index sear ch This function locates and adv ances/rewinds to the position where the inde x signal is recorded. Use the remote controller . 䡵 To locate an index in the forwar d direction vis-a-vis the current tape position: • Press the INDEX + button.
E-47 PLA YBACK – Selecting playback audio output – The output mode f or audio pla yback can be selected with the remote controller . DISPLA Y BARS MENU SEARCH+ SEARCH– A.DUB F .REV INDEX – INDEX + PLA Y STOP VEQ3533 REW FF PA USE SET BLANK STILL MODE VCR POWER /I AUDIO MUTING OUT SEL.
E-48 This unit can be used as a f eeder (play er) for an editing system that uses a RS-422A-compat- ible editing remote controller (A G-A850). Applicable model Editing remote contr oller :A G-A850 Recorder :D VC PR O .
E-49 • REM ST OP SEL: Use this menu item to set the operation mode upon reception of a standby-on signal. EE : EE mode (ST OP mode) PB : PLA YBACK mode (STILL mode) • PLA Y DELA Y: Use this menu item to set the edit timing. If delay occurs at the star t of editing, correct this time discrepancy by adjusting the tim- ing for starting playbac k.
E-50 Using the unit in a non-linear system This is a system that captures the content of the source tape on a non-linear editing system and records the non-linear edited contents onto the main unit. EDIT – Using the unit in an editing system – (continued) Connection Setting this unit Set the INPUT switch of the fr ont panel to “DV”.
E-51 MENU SCREEN – Structure of the menu – Hierarchical menus are displa yed on the monitor . MEN U SY STE M . . REM OT E . . AUD I O /VID E O . . TI M E CODE .
E-52 The various functions of this unit can be set from the men u. The configured settings are sav ed in the unit's memor y and are maintained ev en after the power is turned off .
E-53 EJECT MENU REW SET FF PLA Y STOP REC INH. PA L A UDIO NTSC D VCAM PA USE REC CH 1 / 3 2 / 4 E O EJECT button PA USE button FF button ST OP button REW button PLA Y button.
E-54 MENU SCREEN – Contents of the menus – In the menu descriptions below , settings with marks are factory settings. T op MENU Items Setting Contents SYSTEM REMO TE A UDIO/VIDEO TIME CODE DISPLA Y SET CLOCK ADJUST FA C T ORY SETTING DR UM HOUR METER EXIT CANCEL EXECUTE Displa ys the menus related to the operation system of this unit.
E-55 SYSTEM menu SYSTEM menu Items Setting Contents STILL MODE SERIES REC TIME STILL TIMER PA USE PRO TECT INDEX WRITE DC IN MODE PA GE BACK FIELD 1st 2nd FRAME OFF 25MIN 55MIN 75MIN 115MIN 175MIN 265MIN 30SEC 1MIN 2MIN 3MIN 5MIN F.
E-56 REMO TE menu REMO TE menu Items Setting Contents LOCAL FUNCTION PREROLL REM FF/REW MODE REM ST OP SEL PLA Y DELA Y SYNCHRONI- ZA TION CONTROLLER SEL NO KEY EJECT STP + EJT ALL KEYS 3SEC 5.
E-57 A UDIO/VIDEO menu Items Setting Contents A UDIO MODE A.OUT A T SEARCH A UDIO OUT SEL A UDIO OUT LEV SET UP (NTSC) PA GE BACK 48K 32K OFF ON CH-1/2 MIX CH-3/4 AT T NORM OFF ON Select the audio sampling frequency f or recording: 48K : Records at 48kHz.
E-58 MENU SCREEN – Contents of the menus – (continued) TIME CODE menu Items Setting Contents TC CLEAR NDF/DF (NTSC) DV TC DUP . TC OUT OFFSET PA GE BACK CANCEL EXECUTE NON DROP DROP OFF ON OFF +1F +2F –2F –1F Presets the time code: F or details, please ref er to P age 35 "Setting Time Codes".
E-59 DISPLA Y menu DISPLA Y menu Items Setting Contents DISPLA Y COUNTER POSI. TIME CODE VTR MODE T APE REMAIN TIME/D A TE OFF ON AU TO LOWER-R LOWER-L UPPER-R UPPER-L CENTER OFF ON OF.
E-60 MENU SCREEN – Contents of the menus – (continued) DISPLA Y menu (continued) Items Setting Contents A UDIO INFO. D A TE STYLE TIME STYLE BARS PA GE BACK OFF ON Y/M/D M/D/Y D/M/Y 24.
E-61 OTHERS – Placing the unit in an upright position – With the use of the provided stand, the main unit can be placed in an upright position as shown in the f ollowing diagr am. The left side should be at the bottom. Stand Notes •T o place the VTR in an upr ight position, please use the provided stand.
E-62 OTHERS – W ar ning display – When an anomaly occurs, this unit automatically identifies the cause and displa ys an error- coded warning message on the monitor . If the unit is in a state needing rectification, or if an operation error has occurred, an alarm displa y will be shown on the monitor .
E-63 CONDENSA TION ON DR UM W ARNING 3200 LOADING F AILURE W ARNING 3300 UNLOADING F AILURE W ARNING 4100 CASSETTE EJECT F AILURE DEFECTIVE T APE! 5605 - 5609 W ARNING 5702 T APE END DET .
E-64 OTHERS – T r oubleshooting – Symptom Action The power does not come on. The cassette cannot be loaded. Unable to recor d. The operation buttons of the main unit do not work. The 9 PIN REMO TE function does not work. Noise appears on the pla yback screen.
E-65 OTHERS – Checking the hour meter – This unit displa ys the drum usage time on the DRUM HOUR METER item of the top MENU . Please use it as a guide f or regular maintenance. ( ☞ P age 7) EJECT MENU REW SET FF PLA Y STOP REC INH. PA L AUDIO NTSC DVCAM PA USE POWER REC A.
E-66 68 174 260 EJECT MENU REW SET FF PLAY STOP REC INH. PAL A UDIO NTSC DVCA M PAU SE POWER REC A.DUB CH 1 / 3 2 / 4 LINE DV S-VIDEO OFF 9PIN WIRELESS INPUT REMOTE MIC AG-DV2500 OTHERS – Specification – General Recording system :D V system (SP mode only) Signal system : NTSC/P AL Cassette : Standard/ mini D V cassette T ape width : 6.
E-67 OTHERS – Supplement – AC adapter section IMPOR T ANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) K eep these instructions. 3) Heed all warnings. 4) Follo w all instructions. 5) Do not use this apparatus near water . 6) Clean only with dry cloth.
E-68 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN.
Ein wichtiger Punkt beim Kauf des Geräts Panasonic AG-DV2500P (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Panasonic AG-DV2500P noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Panasonic AG-DV2500P - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Panasonic AG-DV2500P reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Panasonic AG-DV2500P erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Panasonic AG-DV2500P besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Panasonic AG-DV2500P verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Panasonic AG-DV2500P. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Panasonic AG-DV2500P gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
