Benutzeranleitung / Produktwartung M3202C des Produzenten LG Electronics
Zur Seite of 67
M ake sure to read the Safety Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. S ee the label attached on the product and give the information to your dealer when you ask for service.
1 Connecting the stand First, check if the following parts are all present. Stand (1) Screws (6) Parts 1. Take the parts for the stand out of the box and assemble them as shown in the picture. 2. Place a soft cloth on the table and put the product with the screen facing downward.
2 Connecting the Stand cover 1. Disassemble the stand cover. The cover may be easily disassembled by pressing up on the base as shown in the figure. 2. After connecting the cables, correctly position the stand cover into the holes on the stand. If securely connected, you will hear the latch click into place.
3 Connecting the Speakers Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. - Only on some models.
4 Connecting the Speakers Mount the product onto the speaker by using a screw as shown in the following connect the speaker cable. - Only on some models. Type 2 When the speaker is installed. * This feature is not available in all model. Remove the paper.
5 Using the Remote Control Name of the Remote Control Buttons 1 2 3 4 5 6 7 8 0 9 * • AV Button • Sleep Button When watching AV, RGB PC,HDMI/DVI , Component1, Component2 The product will be automatically turned off after a certain period of time.
6 Name and Function of the Parts Rear View *LINE OUT A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC sound card has only Speaker Out, reduce the PC volume.
7 First of all, see if the computer, product and the peripherals are turned off. Then, connect the signal input cable. When connecting with the D-Sub signal input cable.
8 Select an input signal. Press the INPUT button on the remote control to select the input signal. Or, press the INPUT botton on the bottom of the product. INPUT SET • How to connect to two computers. Connect the signal cables ( HDMI to DVI and D-Sub) to each computer.
9 Use this function when displaying ANALOG RGB inputs of a PC to the other product. RGB IN RGB OUT RGB IN RGB OUT RGB IN RGB OUT RGB IN RGB OUT Product 1 • To use different products connected to eac.
10 The Set is equipped with a kensington Securify System connector on the back panel. The cable and lock are available separate and are not sold by LG. For more info, visit http://www.kensington.com, the internet home page of the Kensington company. VESA FDMI wall Mounting This product supports a VESA FDMI compliant mounting interface.
11 Connecting to External Devices AV Component1 Component2 RGB PC HDMI/DVI • AV Button Toggles through video 1 2 3 4 5 6 7 8 0 9 * If you press the button once, the following Input Signal Window will appear. Select the signal type you want using the button.
12 Connecting to External Devices When connecting with an BNC cable. • Select AV. When connecting with an S-Video cable. • Select AV. B A IN OUT When connecting with a S-Video cable. • Connect to the S-Video input terminal to watch high image quality movies.
13 • Select Component 1 • Select Component 2 B A M Connect the video/audio cable as shown in the below figure and then, connect the power cord (See page 7). • Connect the input terminal with a proper color match. BNC Cable (not included) Product HDTV Receiver Component Input (480i/480p/576i/576p/720p/1080i) Select an input signal.
14 Connect the video/audio cable as shown in the below figure and then connect the power cord (See page 7). RCA-PC Audio Cable Product VCR/DVD/Set-top Box HDMI to DVI Signal Cable (not included) HDMI Input (480p/576p/720p/1080i/1080p) VCR/DVD/Set-top Box Product Select an input signal.
15 - When using AV input, you can connect the AV Out to other monitors. IN OUT Video/TV W atching A V Outputs BNC Cable (not included) Audio Cable (not included) BNC Cable (not included) Audio Cable (not included) Video/TV Product Connecting to External Devices • When multi-connecting in/out cascade format, no loss cables are recommended.
16 User Menus Screen Adjustment options • Press this button to turn on the power. Press this button again to turn it off. • This Indicator lights up green when the display operates normally (on mode). If the display is in sleep (Energy Saving) mode, this indicator color changes to amber.
17 • This is where the unit receives signals from the remote control. Screen Adjustment options [For PC Analog signal] AUTO/SET Button AV Composite Video, Separate Video Component 1 HDTV, DVD Compon.
18 User Menus OSD Menu Icon Function Description Picture Audio Adjusts the audio options. Adjusts screen brightness, contrast and color that you prefer. Note O SD(On Screen Disp lay) The OSD function enables you to adjust the screen status conveniently since it provides graphical presentation.
19 How to adjust the OSD (On Screen Display) screen • Use the remote control to adjust the OSD screen. How to adjust the screen automatically Press the AUTO/SET button (AUTO button on a remote Control) in the PC analog signal. Then optimal screen settings will be selected that fit into the current mode.
20 User Menus Adjusting Screen Color Backlight : To control the brightness of the screen,adjust the brightness of LCD panel. Contrast : Adjust the difference between the light and dark levels in the picture. Brightness : To adjust the brightness of the screen.
21 Red / Green / Blue Set your own color levels. Color Settings • Cool : Slightly purplish white. • Medium : Slightly bluish white. • Warm : Slightly reddish white.
22 User Menus • NR : Removing the noise up to the point where it does not damage the original picture. • Gamma : Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images.
23 User Menus To select the image size of the screen. Aspect Ratio The aspect ratio is not adjusted from the original. It is set by the program being watched. Original This picture format is 4:3 aspect ratio. 4:3 Widescreen mode. 16:9 14:9 programs are viewed normally in 14:9 with black bars added to the top and bottom.
24 MENU Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen To set User Menus Adjusting Screen Color Return Picture Mode , Color Temperature , Advanced to the default factory settings. Picture Reset MENU Picture Picture Mode Color Temperature Advanced Aspect Ratio Picture Reset Screen To set Auto Config.
25 User Menus The best sound tone quality will be selected automatically depending on the video type that you're currently watching. Sound Mode Adjusting the audio function Note When connected to.
26 Clock Adjusting the timer function In the event of power interruption (disconnection or power failure), the clock must be reset. Once the on or off time is set, these functions operate daily at the preset time. Off time function overrides On time function if they are set to the same time.
27 User Menus Selecting the options Language To choose the language in which the control names are displayed. Use the buttons to select On or Off . The monitor can be set up so that it can only be used with the remote control. This feature can prevent unauthorized viewing.
28 Tile mode Tile mode and choose Tile alignment and set the ID of the current product to set location. * Only after pressing the SET button the adjustments made to the settings will be saved. It is used to enlarge the screen and also used with several products to view screen.
29 User Menus ID 1 ID 2 row column - Tile mode (product 1 ~ 2) : r(2) x c(1) column row - Tile mode (product 1 ~ 9) : r(3) x c(3) ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 column row - Tile mode (p.
30 Adjust the horizontal size of the screen taking into account the size of the bezel. Adjust the vertical size of the screen taking into account the size of the bezel. • H-Size • V-Size • Reset Select the location of the Tile by setting an ID. • Tile ID Function to initialize and release Tile.
31 User Menus Adjust Set ID and check Serial No. and SW version. MENU Information Set ID Serial No. SW Version You can assign a unique Set ID NO (name assignment) to each product when several products are connected for display. Specify the number (1~99) using the button and exit.
32 • See if the power cord is properly connected to the outlet. • See if the power switch is turned on. • May need service. • Adjust brightness and contrast again. • Backlight may need repair. • If the product is in power saving mode, move the mouse or press any key.
33 ● Is the screen position wrong? ● Do thin lines appear on the background screen? ● Horizontal noise appears or the characters look blurred. ● The screen is displayed abnormally.
34 • Set the number of colors to more than 24 bits (true color) Select Control Panel – Display – Settings – Color Table menu in Windows. • Check the connection status of the signal cable.
35 LCD Panel Power Dimensions &Weight NOTE Information in this document is subject to change without notice. 32 inches Visible diagonal (80.0 cm) TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel 0.5025 mm X 0.5025 mm (Pixel Pitch) Rated Voltage AC 100-240V~ 50/60Hz 1.
36 Specifications LCD Panel Power Dimensions &Weight NOTE Information in this document is subject to change without notice. 37 inches Visible diagonal (94.0 cm)TFT (Thin Film Transistor) LCD (Liquid Crystal Display) Panel 0.6000 mm X 0.6000 mm (Pixel Pitch) Rated Voltage AC 100-240V~ 50/60Hz 2.
37 Specifications NOTE Information in this document is subject to change without notice. Max. Resolution RGB : 1600 X 1200 @60Hz HDMI/DVI : 1920 X 1080 @60Hz – It may not be supported depending on the OS or video card type.
38 Preset mode Horizontal Frequency (kHz) Vertical Frequency (Hz) PC Mode – Preset Mode Preset mode Horizontal Frequency (kHz) Vertical Frequency (Hz) 1 2 *3 4 *5 6 7 *8 9 *10 640 x 350 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1280 x 720 31.
Controlling the Multiple Product RS-232C A1 Connecting the cable Connect the RS-232C cable as shown in the picture. * The RS-232C protocol is used for communication between the PC and product. You can turn the product on/off, select an input source or adjust the OSD menu from your PC.
Controlling the Multiple Product RS-232C A2 Command Reference List COMMAND1 COMMAND2 DATA1 DATA2 DATA3 01. Power k a 00H - 01H 02. Input Select k b 02H - 09H 03. Aspect Ratio k c 01H - 09H 04. Screen Mute k d 00H - 01H 05. Volume Mute k e 00H - 01H 06.
OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Product transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.
T ransmission / Receiving Protocol 01. Power(Command : a) To control Power On/Off of the Set. Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [a][ ][Set ID][ ][OK][Data][x] To show the status of Power On/Off.
03. Aspect Ratio(Command : c) (Main picture format) To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu.
05. Volume Mute(Command : e) To control On/Off of the Volume Mute. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) Acknowledgement [e][ ][Set ID][ ][OK][Data][x] Data 0 : Volume Mute On (Volume Off) 1 : Volume Mute Off (Volume On) 06.
Controlling the Multiple Product RS-232C A7 T ransmission / Receiving Protocol 07. Contrast(Command : g) To adjust screen contrast. You can also adjust the contrast in the Picture menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H • Refer to ‘Real data mapping’ as shown below.
Controlling the Multiple Product RS-232C A8 T ransmission / Receiving Protocol 09. Color(Command : i) (Video only) To adjust the screen color. You can also adjust the color in the Picture menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7.
Controlling the Multiple Product RS-232C A9 11. Sharpness(Command : k) (Video only) To adjust the screen Sharpness. You can also adjust the sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7.
Controlling the Multiple Product RS-232C A10 T ransmission / Receiving Protocol 14 Balance(Command : t) To adjust the sound balance. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00H ~ Max : 64H (Hexadecimal code) • Refer to ‘Real data mapping’ page A7.
Controlling the Multiple Product RS-232C A11 T ransmission / Receiving Protocol 16. Abnomal state (Command : z) Abnormal State : Used to Read the power off status when Stand-by mode.
Controlling the Multiple Product RS-232C A12 18. Auto Configure(Command: j u) To adjust picture position and minimize image shaking automatically. it works only in RGB(PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 1 : To set Acknowledgement [u][ ][Set ID][ ][OK][Data][x] T ransmission / Receiving Protocol ▲ 19.
Controlling the Multiple Product RS-232C A13 20. Tile Mode(Command : d d) Change a Tile Mode. Transmission [d][d][][Set ID][][Data][x] * The data can not be set to 0X or X0 except 00. Acknowledgement [d][][00][][OK/NG][Data][x] T ransmission / Receiving Protocol Data Description 00 Tile mode is off.
Controlling the Multiple Product RS-232C A14 21. Tile H Size(Command : d g) To set the Horizontal size. Transmission [d][g][][Set ID][][Data][x] Data Min : 00H ~ Max : 64H Acknowledgement [g][][Set ID][][OK/NG][Data][x] 22. Tile V Size(Command : d h) To set the Vertical size.
Controlling the Multiple Product RS-232C A15 23. Tile ID Set(Command : d i) To assign the Tile ID for Tiling function . Transmission [d][i][][Set ID][][Data][x] Data Min : 00H ~ Max : 19H (Hexadecimal.
Controlling the Multiple Product RS-232C A16 26. Temperature value (Command : d n) To read the inside temperature value. Transmission [d][n][][Set ID][][Data][x] * The data is always FF(in Hex). Acknowledgement [n][][Set ID][][OK/NG][Data][x] * The data is 1 byte long in Hexadecimal.
Controlling the Multiple Product RS-232C A17 28. Auto volume (Command : d u) Automatically adjust the volume level. Transmission [d][u][][Set ID][][Data][x] Data 0 : Off 1 : On Acknowledgement [u][][Set ID][][OK/NG][Data][x] 29. Speaker (Command : d v) Turn the speaker on or off.
Controlling the Multiple Product RS-232C A18 30. Time (Command : f a) Set the current time. Transmission [f][a][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 : Wednesday 3 :.
Controlling the Multiple Product RS-232C A19 31. On Timer (On/Off Timer) On, Off (Command : F b) Set days for On Timer. Transmission [f][b][][Set ID][][Data1][][Data2][Cr] [Data1] 0 (Write), FFH(Read).
Controlling the Multiple Product RS-232C A20 33. On Timer (On/Off Timer) Time (Command : f d) Set On Timer. Transmission [f][d][][Set ID][][Data1][][Data2][Data3][Cr] [Data1] 0 : Monday 1: Tuesday 2 :.
Controlling the Multiple Product RS-232C A21 34. Off Timer (On/Off Timer) Time (Command : f e) Set Off Timer. Transmission [f][e][][Set ID][][Data1][][Data2][][Data3][Cr] [Data1] 0 : Monday 1: Tuesday.
Controlling the Multiple Product RS-232C A22 35. Sleep Time (Command : f f) Set Sleep Time. Transmission [f][f][][Set ID][][Data][Cr] Data 0 : Off 1 : 10 2 : 20 3 : 30 4 : 60 5 : 90 6 : 120 7 : 180 8 : 240 (Orderly) Acknowledgement [f][][Set ID][][OK/NG][Data][x] ▲ T ransmission / Receiving Protocol 36.
Controlling the Multiple Product RS-232C A23 37. Power On Delay (Command : f h) Set the schedule delay when the power is turned on (Unit: second). Transmission [f][h][][Set ID][][Data][Cr] Data : 00H ~ 64H (Data value) Acknowledgement [h][][Set ID][][OK/NG][Data][x] T ransmission / Receiving Protocol ▲ 38.
Controlling the Multiple Product RS-232C A24 39. DPM Select (Command : f j) Set the DPM (Display Power Management) function. Transmission [f][j][][Set ID][][Data][Cr] Data 0 : Off 1: On Acknowledgement [j][][Set ID][][OK/NG][Data][x] T ransmission / Receiving Protocol ▲ 40.
Controlling the Multiple Product RS-232C A25 41. S/W Version (Command : f z) Check the software version. Transmission [f][z][][Set ID][][Data][Cr] Data FFH : Read Acknowledgement [z][][Set ID][][OK/NG][Data][x] T ransmission / Receiving Protocol ▲ 42.
RS-232C A26 IR Codes How to connect Remote Control IR Code Connect your wired remote control to Remote Control port on the Product. Output waveform single pulse, modulated with 37.
RS-232C A27 ▲ ▲ 00 01 02 03 08 C4 C5 09 98 0B 0E 43 5B 6E 44 10 11 12 13 14 15 16 17 18 19 5A BF D4 D5 C6 79 76 77 AF 99 ▲ ▼ VOL( ) VOL( ) POWER ON/OFF POWER ON POWER OFF MUTE AV INPUT SLEEP M.
P/NO : 3 8 40TRL098E (0 80 1-REV00) www .lge.com.
Ein wichtiger Punkt beim Kauf des Geräts LG Electronics M3202C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie LG Electronics M3202C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für LG Electronics M3202C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von LG Electronics M3202C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über LG Electronics M3202C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon LG Electronics M3202C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von LG Electronics M3202C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit LG Electronics M3202C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei LG Electronics M3202C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
