Benutzeranleitung / Produktwartung W701DS des Produzenten Lenovo
Zur Seite of 264
T hinkP a d W7 00 , W7 00d s, W7 0 1 , an d W7 0 1d s Hard w ar e M a i nte n a n c e M a n ua l.
.
T hinkP a d W7 00 , W7 00d s, W7 0 1 , an d W7 0 1d s Hard w ar e M a i nte n a n c e M a n ua l.
Note Before using this information and the pr oduct it supports, be sure to read the general information under “Notices” on page 253. Seventh Edition (March 2010) © Copyright Lenovo 2008, 2010.
Contents About this manual .......... v Safety information .......... 1 General safety .............. 2 Electrical safety ............. 3 Safety inspection guide ........... 5 Handling devices that are sensitive to electr ostatic discharge ...........
1 1 9 0 C P U ............... 1 3 5 1200 V ideo card ............ 1 3 6 1210 HDD I/O sub card .......... 1 3 8 1220 LCD unit and LCD cable cap ...... 1 4 4 1230 Structure frame ........... 1 5 0 1240 ODD switch sub card for W700 and W700ds 153 1250 Audio and card r eader I/O card .
About this manual This manual contains service and refer ence information for the following ThinkPad ® products. ThinkPad W700 and W700ds MT 2752, 2753, 2754, 2757, 2758, 2762, and 2763 ThinkPad W701 and W701ds MT 2500, 2541, 2542, 2543, 2544, 4323, and 4326 Use this manual along with the advanced diagnostic tests to troubleshoot problems.
vi ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook. v “General safety” on page 2 v “Electrical safety.
General safety Follow these rules to ensur e general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet.
Electrical safety Observe the following rules when working on electrical equipment. v Find the room emer gency power-off (EPO) switch, disconnecting switch, or electrical outlet. If an electrical accident occurs, you can then operate the switch or unplug the power cord quickly .
v Do not touch live electrical circuits with the r eflective surface of a plastic dental mirror . The surface is conductive; such touching can cause personal injury and machine damage.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, requir ed safety items were installed to pr otect users and service technicians from injury .
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electr ostatic discharge (ESD.) ESD damage can occur when there is a dif ference in charge between objects.
Safety notices (multilingual translations) The safety notices in this section are pr ovided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese .
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer . V erify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
DANGER T o avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials.
10 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 11.
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador . V erifique isso sacudindo o computador e procurando ouvir sons de peças soltas.
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
DANGER A vant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit.
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber . Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 19.
20 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 21.
22 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 23.
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían.
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 27.
Laser compliance statement (multilingual translations) The laser compliance statements in this section are pr ovided in the following languages: v English v Arabic v Brazilian Portuguese v French v Ge.
Safety information 29.
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. T ais dispositivos também são vendidos separadamente como opcionais.
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options.
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforder ungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1.
Safety information 33.
34 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Safety information 35.
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM.
Safety information 37.
38 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Important service information This chapter presents following important service information that applies to all machine types supported by this manual: v “Strategy for replacing FRUs” – “Strat.
Use the following strategy to prevent unnecessary expense for r eplacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue . v Some computers have both a processor boar d and a system board.
Strategy for replacing FRUs for CT O, CMV , and GA V Product definition Dynamic Configure T o Order (CTO) This provides the ability for a customer to configur e an IBM ® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, wher e it is built and shipped directly to the customer .
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim r ecord under SYSTEM DET AILS. v Authorized IBM Business Partners can access Eclaim at the following W eb site: https://wca.
General checkout This chapter presents following information: v “What to do first” on page 44 v “Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Leno.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3. Date on which the machine failed __ 4.
Checkout guide Use the following procedur es as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad pr oducts. The use of non-ThinkPad products, pr ototype cards, or modified options can lead to false indications of errors and invalid system r esponses.
T esting the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. T o run the test, do as follows: 1. T urn off the computer .
The options on the test menu are as follows: Diagnostics Interactive T ests v Run Normal T est v Run Quick T est v CPU/Coprocessor v Systemboard v V ideo Adapter v Fixed Disks v Diskette Drives v Othe.
v Print Log v Save Log v Full Erase Hard Drive v Quick Erase Hard Drive Lenovo ThinkV antage T oolbox (Lenovo System T oolbox) Lenovo ThinkV antage ® T oolbox (Lenovo System T oolbox in W indows V ista ® and W indows ® XP) is a diagnostic program that works thr ough the W indows operating system.
PC-Doctor for Rescue and Recovery In some models of ThinkPad Notebook, the Rescue and Recovery ® workspace enables you to run the PC-Doctor pr ogram to test the hardware featur es of the computer . T o run the test, click “Run Diagnostics” on the Rescue and Recovery main scr een.
FRU tests The following table shows the test for each FRU. T able 1. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad W700 Mini Dock is attached to the ThinkPad computer , detach it.
T able 1. FRU tests (continued) FRU Applicable test Memory 1. If two DIMMs are installed, r emove one of them and run Diagnostics --> Memory T est—Quick . 2. If the problem does not r ecur , return the DIMM to its place, remove the other one, and run the test again.
Power system checkout T o verify a symptom, do the following: 1. T urn off the computer . 2. Remove the battery pack. 3. Connect the ac adapter . 4. Check that power is supplied when you turn on the computer . 5. T urn off the computer . 6. Disconnect the ac adapter and install the charged battery pack.
Checking operational charging T o check whether the battery charges pr operly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer . Perform operational charging.
Checking the backup battery Do the following: 1. Power off the computer , and unplug the ac adapter from it. 2. T urn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 88). 4. Remove the backup battery (see “1 100 Backup battery” on page 106).
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Restoring the factory contents by using Recovery Di.
8. When the recovery pr ocess is complete, the W elcome to Microsoft W indows screen is displayed. Follow the instr uctions on the screen to complete the W indows setup.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next . If you do not agree with the terms and conditions, follow the instructions on the scr een. 6. Click Ye s in the displayed window to begin the operating system r ecovery process.
Note: There ar e two modes for the HDP: User only and Master + User . The Master + User mode requir es two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user . Attention: If the user HDP has been for gotten, check whether a master HDP has been set.
5. Select Power-On Password . 6. T ype the current SVP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 7. In the Changes have been saved window , press Enter . 8. Press F10; then, in the Setup confirmation window , select Ye s .
Power management T o reduce power consumption, the computer has thr ee power management modes: screen blank, sleep (standby in W indows XP), and hibernation. Screen blank mode If the time set on the “T urn off monitor” timer in the operating system expir es, the LCD backlight turns off.
Also, in either of the following events, the computer automatically returns fr om sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v .
T able 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 Invalid RFID configuration information area—The EEPROM checksum is not corr ect.
T able 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter . 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date.
T able 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized W AN card is plugged in—Power off and r emove the W AN car d. 1. Remove the W AN card that you installed. 2. System board. 1820 More than one external fingerprint r eader is attached.
Error messages T able 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility . 2. Backup battery . 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility .
Beep symptoms T able 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector . 2. LCD assembly . 3. External CR T . 4. System board. One long and two short beeps, and a blank or unreadable LCD.
LCD-related symptoms T able 6. LCD-related symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, and a blank LCD during POST . System board . v LCD backlight not working. v LCD too dark. v LCD brightness cannot be adjusted.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardwar e defect, such as cosmic radiation, electrostatic discharge, or softwar e errors. FRU replacement should be consider ed only when a problem r ecurs.
70 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Installing and configuring RAID This chapter presents following information about attaching SA T A devices and configuring RAID for this product. v “Supported RAID configurations” v “Configuring.
Creating RAID volumes This section describes how to use the Intel ® Matrix Storage Manager option ROM Configuration Utility to create RAID volumes. T o create RAID volumes, do as follows: 1.
Status indicators This chapter presents the system status indicators that show the status of the computer . 13 8 9 10 T able 7. Status indicators Indicator Meaning 1 W ireless LAN status Green: The wireless featur e (802.1 1 standard) is on, and the radio link is ready for use.
T able 7. Status indicators (continued) Indicator Meaning 2 Bluetooth wireless or W ireless USB status R or Green: The Bluetooth wireless featur e or W ireless USB feature is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
T able 7. Status indicators (continued) Indicator Meaning 11 Serial Ultrabay Enhanced status only for W700 and W700ds Green: An Serial Ultrabay Enhanced device is installed and in use. Blinking green: An Serial Ultrabay Enhanced device is in the process of being detached.
76 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Fn key combinations The following table shows the function of each combination of Fn with a function key . T able 8. Fn key combinations Key combination Description Fn+F1 Reserved.
T able 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme dir ectly , with no need to start Presentation Dir ector . T o disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Dir ector , and change the settings.
T able 8. Fn key combinations (continued) Key combination Description Fn+F12 Put the computer into hibernation mode. T o return to normal operation, press the power button for less than four seconds. Notes: v Though the screen fades out immediately after Fn+F12 ar e pressed, the computer does not enter the hibernation mode immediately .
80 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
FRU replacement notices This chapter presents notices r elated to removing and replacing parts. Read this chapter carefully befor e replacing any FRU. Screw notices Loose screws can cause a r eliability problem.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number . When you replace the system boar d, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardwar e Maintenance Diskette V ersion 1.
84 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Removing and replacing a FRU This chapter presents dir ections and drawings for use in removing and replacing a FRU. Be sure to observe the following general r ules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
Important notice for servicing ThinkPad W700ds and W701ds The computer display is designed to be opened and used at an angle slightly greater than 90 degr ees. Do not open the main display beyond 150 degrees. T o do so might damage the computer hinge.
v When the second screen is extended, the main display and the second scr een work in the Extend desktop mode, but not single mode or clone mode. Removing and replacing a FRU 87.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer . Any other battery could ignite or explode. T able 9. Removal steps of battery pack 2 1 Important notice fo.
1020 Digitizer pen T able 10. Removal steps of digitizer pen 2 1 Removing and replacing a FRU 89.
1030 Serial Ultrabay Enhanced device T able 1 1. Removal steps of Serial Ultrabay Enhanced device When you release the switch in step 1 , the lever pops out.
1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1010 Battery pack” on page 88 T able 12.
T able 12. Removal steps of HDD cover , HDD and HDD rubber rails or SSD and storage converter (continued) 2 Note: Mounted number of the hard disk drive depends on the models. In models with RAID features, two har d disk drives that have same FRU no. must be used in slot 0 ( a ) and in slot 1 ( b ).
T able 12. Removal steps of HDD cover , HDD and HDD rubber rails or SSD and storage converter (continued) SSD and storage converter: 6 5 Removing and replacing a FRU 93.
1050 DIMM slot cover and DIMM For access, remove this FRU: v “1010 Battery pack” on page 88 T able 13. Removal steps of DIMM slot cover and DIMM Note: Loosen the screws 1 , but do not r emove them.
T able 13. Removal steps of DIMM slot cover and DIMM (continued) For ThinkPad W700 and W700ds: 3 3 4 Removing and replacing a FRU 95.
T able 13. Removal steps of DIMM slot cover and DIMM (continued) Note: If only one DIMM is used on the computer you are servicing, the car d must be installed in SLOT -0 ( a ), but not in SLOT -1 ( b ). b a When installing: Insert the notched end of the DIMM into the socket.
T able 13. Removal steps of DIMM slot cover and DIMM (continued) For ThinkPad W701 and W701ds: 3 3 4 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly , and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily .
1060 Palm rest or palm rest with fingerprint reader For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 91 T able 14.
T able 14. Removal steps of palm rest (continued) 2 3 3 4 5 Removing and replacing a FRU 99.
When installing: When you attach the palm rest, do as follows: T able 15. Installation of the palm rest 1. Attach the color sensor connector 1 and the fingerprint reader connector 2 firmly to the system board. Some models have only the fingerprint r eader connector .
T able 15. Installation of the palm rest (continued) 3. Push the front side of the palm r est 4 and the areas marked 5 until it clicks into place. 4 5 5 4. Close the LCD cover and turn the computer over . Then fasten the four screws to secure the palm r est.
1070 Digitizer pen case assembly For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1020 Digitizer pen” on page 89 v “1040 Hard disk drive (HDD) cover , HDD and HDD.
1080 Bluetooth daughter card (BDC-2.1) for W701 and W701ds For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 91 v “1060 Palm rest or palm r est with fingerprint reader” on page 98 T able 17.
1090 Keyboard For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 91 v “1060 Palm rest or palm r est with fingerprint reader” on page 98 T able 18.
T able 18. Removal steps of keyboard (continued) When installing: Make sure that the keyboar d edges a are under the frame as shown in this figure.
1 100 Backup battery DANGER Use only the battery specified in the parts list for your computer . Any other battery could ignite or explode. For access, remove these FRUs in or der: v “1010 Battery p.
T able 19. Removal steps of backup battery (continued) For ThinkPad W701 and W701ds: 2 1 When installing: Make sure that the battery connector is attached firmly .
1 1 10 Numeric keypad For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 91 v “1060 Palm rest or palm r est with fingerprint reader” on page 98 v “1090 Keyboard” on page 104 T able 20.
T able 20. Removal steps of numeric keypad (continued) 4 When installing: Make sure that the keypad edges 1 ar e under the frame as shown in this figure.
T able 20. Removal steps of numeric keypad (continued) 2 a Note: For ThinkPad W701 and W701ds, make sure that the cable 3 is under the frame as shown in this figure.
1 120 DIMM slot cover and DIMM under keyboard for W701 and W701ds For access, remove this FRU: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or .
T able 21. Removal steps of DIMM slot cover and DIMM under keyboard (continued) 1 1 2 Note: If only one DIMM is used on the computer you are servicing, the car d must be installed in the lower slot. When installing: Insert the notched end of the DIMM into the socket.
1 130 Keyboard bezel and speaker assembly For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state .
T able 22. Removal steps of keyboard bezel for W700 and W700ds (continued) 4 3 4 3 When installing: Make sure that all the claws ar e attached firmly .
T able 23. Removal steps of speaker assembly for W700 and W700ds 2 1 1 1 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, small-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) T able 24. Removal steps of keyboard bezel for W701 and W701ds For ThinkPad W701 and W701ds: 1 1 1 1 Step Screw (quantity) Color T orque 1 M2.
T able 24. Removal steps of keyboard bezel for W701 and W701ds (continued) Note: Loosen the screws 2 , but do not r emove them. 2 2 3 11 6 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maint.
T able 24. Removal steps of keyboard bezel for W701 and W701ds (continued) 5 4 5 4 When installing: Make sure that all the claws ar e attached firmly .
T able 25. Removal steps of speaker assembly for W701 and W701ds 2 1 1 1 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, small-head, nylon-coated (3) Silver 0.
1 140 Wireless USB adapter or Intel T urbo Memory Minicard Note: If the Intel T urbo Memory Minicard is installed in the half-size PCI Expr ess Mini Card slot as shown in “1 140 W ireless USB adapte.
Note: Some models do not have the wireless USB antenna cable. T able 26. Removal steps of Wireless USB adapter or Intel T urbo Memory Minicard Note: Step 1 is only for models with the W ireless USB adapter . For models with the Intel T urbo Memory Minicard, skip step 1 .
1 150 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or sol.
T able 27. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX for W700 and W700ds (continued) 3 When installing: v In models with wireless LAN car d that has two antenna connectors, plug the gray cable into the jack labeled MAIN , and the black cable into the jack labeled AUX on the card.
T able 28. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX for ThinkPad W701 and W701ds For ThinkPad W701 and W701ds: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arr ow .
T able 28. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX for ThinkPad W701 and W701ds (continued) When installing: v In models with wireless LAN car d that has two antenna connectors, plug the gray cable into the jack labeled MAIN , and the black cable into the jack labeled AUX on the card.
1 160 Intel T urbo Memory Minicard For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (.
T able 29. Removal steps of Intel T urbo Memory Minicard (continued) 4 126 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
1 170 CPU thermal device/fan For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) a.
T able 30. Removal steps of CPU thermal device/fan for W700 and W700ds (continued) 5 6 T able 31. Installation of the CPU thermal device/fan for W700 and W700ds When installing: v Before you attach the fan assembly to the computer , apply thermal grease, at an amount of 0.
T able 32. Removal steps of CPU thermal device/fan for W701 and W701ds For ThinkPad W701 and W701ds: Note: Loosen the screws 1 , 2 , and 3 , but do not r emove them. When you attach the fan, secure the scr ews in order as shown in this figure.
T able 32. Removal steps of CPU thermal device/fan for W701 and W701ds (continued) T able 33. Installation of the CPU thermal device/fan for W701 and W701ds When installing: v Before you attach the fan assembly to the computer , apply thermal grease, at an amount of 0.
1 180 VGA thermal device/fan and thermal putty Note: In ThinkPad W701 and W701ds, thermal putty is used between the thermal device/fan and the video card. The thermal putty is included in the video car d FRU, but is not included in the thermal device/fan FRU.
T able 34. Removal steps of VGA thermal device/fan (continued) For ThinkPad W700ds and W701ds: 1 2 3 5 4 Attention: Do not handle the fan roughly . Improper handling of the fan can cause distortion or deformation and imperfect contact with components.
T able 35. Installation of the VGA thermal device/fan in ThinkPad W700 and W700ds When installing: v Before you attach the fan assembly to the computer , apply thermal grease, at an amount of 0.2 grams, on the part marked b as in the following figure.
T able 36. Installation of the VGA thermal device/fan and thermal putty in ThinkPad W701 and W701ds When installing: v Before you attach the fan assembly to the computer , attach new thermal putty on the video card as shown as a in this figur e.
1 190 CPU For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converte.
1200 V ideo card Note: When you replace following video car ds, you also need to replace FRUs listed in the following table. 42W8202 V ideo card for MXM NB9E GLM2 42W8204 V ideo card for MXM NB9E GLM3 FRUs need to be replaced simultaneously FRU FRU no.
T able 38. Removal steps of video card (continued) 3 When installing: Before you attach the video car d to the computer , you need to peel the thin film off fr om the rubber marked a .
1210 HDD I/O sub card For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and stor.
T able 39. Removal steps of HDD I/O sub card for W700 and W700ds (continued) For models with 34-mm ExpressCard/Smart Card slot: 1 1 1 2 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, small-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) 2 M2.
T able 39. Removal steps of HDD I/O sub card for W700 and W700ds (continued) For models with 34-mm ExpressCard/CompactFlash Card slot: 1 1 1 1 2 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, small-head, nylon-coated (4) Silver 0.181 Nm (1.
T able 40. Removal steps of HDD I/O sub card for W701 and W701ds For ThinkPad W701 and W701ds: For models with 34-mm ExpressCard/54-mm ExpressCard slot: 1 1 3 2 Step Screw (quantity) Color T orque 1 M2 × 14 mm, small-head, nylon-coated (2) Silver 0.
T able 40. Removal steps of HDD I/O sub card for W701 and W701ds (continued) For models with 34-mm ExpressCard/Smart Card slot: 1 1 3 2 Step Screw (quantity) Color T orque 1 M2 × 14 mm, small-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) 2 M2 × 3.
T able 40. Removal steps of HDD I/O sub card for W701 and W701ds (continued) For models with 34-mm ExpressCard/CompactFlash Card slot: 1 1 3 2 2 2 Step Screw (quantity) Color T orque 1 M2 × 14 mm, small-head, nylon-coated (2) Silver 0.181 Nm (1.
1220 LCD unit and LCD cable cap For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD.
T able 41. Removal steps of LCD unit for W700 and W700ds (continued) 3 3 3 3 4 4 5 Step Screw (quantity) Color T orque 3 M2.5 × 9 mm, wafer-head, nylon-coated (4) Black 0.392 Nm (4 kgfcm) 4 M2 × 10 mm, wafer-head, nylon-coated (2) Black 0.
T able 41. Removal steps of LCD unit for W700 and W700ds (continued) 7 7 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sur e that they are not subjected to any tension.
T able 42. Removal steps of LCD unit for W701 and W701ds For ThinkPad W701 and W701ds: 1 1 2 2 Step Screw cap Screw (quantity) Color T orque 1 — M2.5 × 9 mm, wafer -head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) 2 M2.5 × 9 mm, wafer-head, nylon-coated (2) Black 0.
T able 42. Removal steps of LCD unit for W701 and W701ds (continued) 5 5 5 5 6 6 7 Step Screw (quantity) Color T orque 5 M2.5 × 9 mm, wafer-head, nylon-coated (4) Black 0.392 Nm (4 kgfcm) 6 M2 × 12 mm, wafer-head, nylon-coated (2) Black 0.
T able 42. Removal steps of LCD unit for W701 and W701ds (continued) 10 10 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sur e that they are not subjected to any tension.
1230 Structure frame or access, remove these FRUs, in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage converter” on page 91 v “1060 Palm rest or palm r est with fingerprint reader” on page 98 v “1080 Bluetooth daughter card (BDC-2.
T able 43. Removal steps of structure frame (continued) 4 4a 4a 4 4 4 5 5 6 When installing: Make sure that the connector is attached firmly , and that the cable is routed as in the figur e above. Note: Step 4a is only for ThinkPadW700 and W700ds.
T able 43. Removal steps of structure frame (continued) 7 152 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
1240 ODD switch sub card for W700 and W700ds For access, remove these FRUs, in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid st.
1250 Audio and card reader I/O card For access, remove these FRUs, in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive.
T able 45. Removal steps of audio and card reader I/O card (continued) 2 3 4 When installing: Make sure the connector is attached firmly . Removing and replacing a FRU 155.
1260 System board and base cover Note: When you replace following system boar ds, you also need to replace FRUs listed in the following table. 42W8199 System board for MXM-support, with TPM for W700 42W8201 System board for MXM-support, non-TPM for W700 FRUs need to be replaced simultaneously FRU FRU no.
Important notices for RAID setting: Before you r eplace the system board, make sure that you r ead “Installing and configuring RAID” on page 71, and have the necessary information.
Following components soldered on the top side of the system boar d are extremely sensitive. When you service the system board, avoid any kind of r ough handling.
Following components soldered on the top side of the system boar d are extremely sensitive. When you service the system board, avoid any kind of r ough handling.
T able 46. Removal steps of system board and base cover 1 1 1 2 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover , you need to apply the following labels: 7.
For the location of each label, refer the following figur e: For ThinkPad W701 and W701ds: 1 2 3 6 7 5 4 162 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
2010 LCD front bezel (LCD cover kit) For access, remove this FRU: v “1010 Battery pack” on page 88 T able 47. Removal steps of LCD front bezel 1 1 1 1 1 1 Step Screw cap Screw (quantity) Color T orque 1 M2.5 × 7 mm, wafer-head, nylon-coated (6) Black 0.
2020 Inverter card For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “2010 LCD front bezel (LCD cover kit)” on page 163 T able 48. Removal steps of inverter card for W700 and W700ds For ThinkPad W700 and W700ds: 1 1 3 2 Step Screw (quantity) Color T orque 1 M2 × 3.
T able 49. Removal steps of inverter card for W701 and W701ds For ThinkPad W701 and W701ds: 1 3 2 1 1 Step Screw (quantity) Color T orque 1 M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connectors ar e attached firmly .
2030 Integrated camera For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “2010 LCD front bezel (LCD cover kit)” on page 163 T able 50. Removal steps of integrated camera 1 When installing: Make sure that the connector is attached firmly .
T able 50. Removal steps of integrated camera (continued) 2 2 3 Step Screw (quantity) Color T orque 1 M2 × 3.5 mm, thin-head, nylon-coated (2) Black 0.
2040 Bluetooth daughter card (BDC-2.1) for W700 and W700ds For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “2010 LCD front bezel (LCD cover kit)” on page 163 T able 51. Removal steps of BDC-2.1 1 2 Step Screw (quantity) Color T orque 1 M2 × 3.
2050 LCD panel, hinges, and LCD cable For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state driv.
T able 52. Removal steps of LCD panel, hinges, and LCD cable (continued) 2 3 3 170 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
T able 52. Removal steps of LCD panel, hinges, and LCD cable (continued) 5 4 4 4 4 Step Screw (quantity) Color T orque For ThinkPad W700 and W701 4 M2.5 × 5 mm, wafer-head, nylon-coated (4) Silver 0.392 Nm (4 kgfcm) For ThinkPad W700ds and W701ds 4 M2.
T able 52. Removal steps of LCD panel, hinges, and LCD cable (continued) For ThinkPad W700 and W701: 7 6 6 6 6 6 6 Step Screw (quantity) Color T orque 6 M2.5 × 3.5 mm, wafer-head, nylon-coated (6) Black 0.392 Nm (4 kgfcm) 8 8 8 8 8 8 9 9 Step Screw (quantity) Color T orque 8 M2 × 3 mm, wafer-head, nylon-coated (6) Black 0.
T able 52. Removal steps of LCD panel, hinges, and LCD cable (continued) For ThinkPad W700ds and W701ds: 8 6 7 7 7 6 6 6 6 Step Screw (quantity) Color T orque 6 M2.5 × 7 mm, wafer-head, nylon-coated (5) Black 0.392 Nm (4 kgfcm) 7 M2.5 × 3.
T able 52. Removal steps of LCD panel, hinges, and LCD cable (continued) 12 13 When installing: Make sure that the LCD cable is attached firmly . 174 ThinkPad W700, W700ds, W701, and W701ds Hardwar e .
2060 Second LCD bezel (second LCD cover kit) (for ThinkPad W700ds and W701ds) For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD .
T able 53. Removal steps of second LCD bezel (second LCD cover kit) (for ThinkPad W700ds and W701ds) (continued) 4 5 5 5 5 5 5 5 6 176 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Man.
2070 Second LCD panel (for ThinkPad W700ds and W701ds) For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or.
T able 54. Removal steps of second LCD panel (for ThinkPad W700ds and W701ds) (continued) 4 178 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
2080 Second LCD cable assembly (for ThinkPad W700ds and W701ds) For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber.
T able 55. Removal steps of second LCD cable assembly (for ThinkPad W700ds) For ThinkPad W700ds: 1 1 1 2 3 4 Step Screw (quantity) Color T orque 1 M2.5 × 4.5 mm, wafer-head, nylon-coated (3) Silver 0.392 Nm (4 kgfcm) 2 M2.5 × 7 mm, wafer-head, nylon-coated (1) Silver 0.
T able 55. Removal steps of second LCD cable assembly (for ThinkPad W700ds) (continued) 6 6 5 Removing and replacing a FRU 181.
T able 56. Removal steps of second LCD cable assembly (for ThinkPad W701ds) For ThinkPad W701ds: 1 2 182 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
T able 56. Removal steps of second LCD cable assembly (for ThinkPad W701ds) (continued) 3 3 3 4 5 6 Step Screw (quantity) Color T orque 3 M2.5 × 4.5 mm, wafer-head, nylon-coated (3) Silver 0.392 Nm (4 kgfcm) 4 M2.5 × 7 mm, wafer-head, nylon-coated (1) Silver 0.
T able 56. Removal steps of second LCD cable assembly (for ThinkPad W701ds) (continued) 8 8 7 184 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
2090 Second LCD hinges and second LCD rear cover (second LCD cover kit) (for ThinkPad W700ds and W701ds) For access, remove these FRUs in or der: v “1010 Battery pack” on page 88 v “1040 Hard di.
T able 57. Removal steps of second LCD hinges and second LCD rear cover (second LCD cover kit) (for ThinkPad W700ds and W701ds) 1 1 Step Screw (quantity) Color T orque 1 M2.
T able 57. Removal steps of second LCD hinges and second LCD rear cover (second LCD cover kit) (for ThinkPad W700ds and W701ds) (continued) 3 4 4 3 Step Screw (quantity) Color T orque 3 M2.
2100 Wireless LAN antenna assembly and wireless USB antenna v “1010 Battery pack” on page 88 v “1040 Hard disk drive (HDD) cover , HDD and HDD rubber rails or solid state drive (SSD) and storage.
T able 58. Removal steps of wireless LAN antenna assembly and UWB antenna (continued) When installing: As you route the cables, make sur e that they are not subjected to any tension. T ension could cause the cables to be damaged by the cable guides, or a wire to be br oken.
190 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Locations This chapter presents the location of ThinkPad W700, W700ds, W701, and W701ds features and har dware. Front view (for ThinkPad W700 and W701) 1 ThinkLight 2 Integrated camera (for some models) 3 Status indicators Note: For the description of each indicator , see “Status indicators” on page 73.
13 Security keyhole 14 Serial Ultrabay Enhanced latch 15 Serial Ultrabay Enhanced device eject lever 16 Serial Ultrabay Enhanced 17 Digitizer pen 18 RJ-1 1 (modem) .
Front view (for ThinkPad W700ds and W701ds) 1 ThinkLight 2 Integrated camera (for some models) 3 Status indicators Note: For the description of each indicator , see “Status indicators” on page 73.
14 Security keyhole 15 Serial Ultrabay Enhanced latch 16 Serial Ultrabay Enhanced device eject lever 17 Serial Ultrabay Enhanced 18 Digitizer pen 19 RJ-1 1 (modem) .
Rear view 1 Status indicators Note: For the description of each indicator , see “Status indicators” on page 73. 2 ExpressCar d/Smart Card/CompactFlash card slot 3 ExpressCar d/Smart Card/CompactFlash card eject button 4 ExpressCar d slot 5 Universal serial bus (USB) 2.
Bottom view 1 Memory-upgrade slot 2 Docking connector 3a Hard disk drive or solid state drive (slot 0) 3b Hard disk drive or solid state drive (slot 1) 4 W ireless radio .
Parts list This section contains following lists of the service parts. v “Overall” on page 198 v “LCD FRUs for ThinkPad W700” on page 224 v “LCD FRUs for ThinkPad W700ds” on page 227 v “.
Overall 1 3 4 5 6 7 8 9 10 11 12 13 14 15 d 25 24 23 21 20 19 18 17 16 31 30 29 27 26 28 22 32 b c a 2 198 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
T able 59. Parts list—Overall No. FRU FRU no. CRU ID a-d See “Miscellaneous parts” on page 235. 1 LCD unit (see “LCD FRUs for ThinkPad W700” on page 224, “LCD FRUs for ThinkPad W700ds” on page 227, “LCD FRUs for ThinkPad W701” on page 229, or “LCD FRUs for ThinkPad W701ds” on page 232.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 8 V ideo card for MXM3.0 N10E-GLM3 v 2500-CTO, 2Ax, 2Bx, 2Gx, 2Lx, 2Mx, 2Xx, 3Cx, 3Ex, 3Jx, 3Kx, 3Mx, 3Nx, 3Px, 3Qx, 3Vx, 3Wx, 3Xx, 3.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 9 4-GB DDR3-1066 SDRAM SO-DIMM (PC3-8500) card v 2752-CTO, E4x, ETx, EUx, EVx, F5x, F7x, FKx, FSx, M9x, MGx v 2753-CTO, E6x v 2754-CT.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 10 System board assembly , MXM-support, non-TPM for W700 v 2752-CTO, 78x, FBx, FCx v 2753-CTO v 2754-CTO v 2757-CTO v 2758-CTO, 76x, .
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 10 System board assembly , MXM-support, non-TPM for W701ds v 2500-CTO, 3Ex v 2541-CTO v 2542-CTO v 2543-CTO v 2544-CTO v 4323-CTO v 4.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 14 DVD-RAM/R W drive, 12.7 mm v 2752-CTO, 36x, 37x, 38x, 3Ax, 3Bx, 3Dx, 3Ex, 3Fx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Xx, 3Yx, 43x, 44x, 45x, 4.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 14 Blu-ray drive, 12.7 mm v 2752-CTO, 3Cx, 3Hx, 3Zx, 42x, 63x, 67x, 6Ux, 6Zx, ETx, F4x, F5x, F7x, F8x, FBx, FCx, FDx, FLx, N3x, N4x v.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 250 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 320 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 320 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 160 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 160 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 250 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 320 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 20 Note: When you replace the HDD or HDDs used in the models with RAID mode, be sur e to install HDDs that have same FRU no.s both in HDD slot 0 and in slot 1. SA T A hard disk drive, 500 GB, 9.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID — SA T A solid state drive, 64 GB, 9 mm v 2752-CTO, 3Nx, 6Ax, 6Bx, 7Dx, EVx, FHx v 2753-CTO v 2754-CTO, 5Wx v 2757-CTO, 4Nx v 2758-.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID — SA T A solid state drive, 128 GB, 9 mm v 2752-CTO v 2753-CTO v 2754-CTO v 2757-CTO v 2758-CTO v 2762-CTO v 2763-CTO v 2500-CTO, 2.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID — SA T A solid state drive, 256 GB, 9 mm (FDE) v 2500-CTO v 2541-CTO v 2542-CTO v 2543-CTO v 2544-CTO v 4323-CTO v 4326-CTO 45N7959.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 23 CPU assembly , Intel Core 2 Duo mobile processor T9550 (2.66 GHz) v 2752-CTO, FUx v 2753-CTO v 2754-CTO v 2757-CTO v 2758-CTO, FFx, LZx v 2762-CTO v 2763-CTO 42W8195 N 23 CPU assembly , Intel Core 2 Duo mobile processor T9600 (2.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 23 CPU assembly , Intel Core 2 Quad processor Q9100 (2.26 GHz) v 2752-CTO, E5x, E7x, EPx, EQx, ERx, ETx, F2x, F3x, FGx, FHx, FSx, FVx.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 23 CPU assembly , Intel Quad Core XE i7-920XM Clarksfield (2.0 GHz) v 2500-CTO, 2Mx, 2Xx, 3Ex, 3Gx, 3Lx, 3Px, 3Tx, 3Ux, 44x, 45x, 49x.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 25 Intel W iMAX/W iFi Link 5350 v 2752-CTO v 2753-CTO v 2754-CTO v 2757-CTO v 2758-CTO v 2762-CTO v 2763-CTO 43Y6533 ** 25 ThinkPad 1.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 28 34-mm ExpressCar d/54-mm ExpressCard slot for W700 and W700ds v 2752-CTO, 36x, 37x, 3Ax, 3Cx, 3Kx, 3Lx, 3Mx, 3Nx, 3Xx, 3Yx, 3Zx, 4.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 28 34-mm ExpressCar d/CompactFlash Card slot for W701 and W701ds v 2500-CTO, 2Ax, 2Ex, 2Gx, 3Dx, 3Ex, 3Fx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3.
T able 59. Parts list—Overall (continued) No. FRU FRU no. CRU ID 30 Palm rest assembly with fingerprint r eader for W701 and W701ds v 2500-CTO, 2Bx, 2Gx, 3Dx, 3Ax, 3Hx, 3Mx v 2541-CTO, 2Px, 2Qx, 2Tx.
LCD FRUs for ThinkPad W700 In ThinkPad W700, there ar e following types of LCDs. v 17.0-in. WXGA+ TFT LCD (T able 60 on page 225) v 17.0-in. WUXGA TFT LCD (T able 61 on page 225) 3 4 5 6 8 10 4 1 7 9 .
T able 60. Parts list—17.0-in. WXGA+ TFT No. FRU FRU no. CRU ID 1 LCD cover kit W700 43Y9790 N 2 LCD bezel 45N6048 N 3 LCD panel, 17.0-in. WXGA+ v 2752-CTO, 3Lx, 3Mx, 43x, 45x, 46x, 5Zx, 62x, 6Kx, 6.
T able 61. Parts list—17.0-in. WUXGA TFT (continued) No. FRU FRU no. CRU ID 3 LCD panel, 17.0-in. WUXGA v 2752-CTO, 36x, 37x, 38x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Hx, 3Jx, 3Kx, 3Nx, 3Xx, 3Yx, 3Zx, 42.
LCD FRUs for ThinkPad W700ds 3 4 8 7 6 2 1 14 13 11 12 10 9 15 5 Parts list 227.
T able 62. Parts list—17.0-in. WUXGA TFT and 10.6-in. WXGA TFT second screen No. FRU FRU no. CRU ID 1 LCD cover kit for W700ds 45N3888 N 2 LCD front bezel 45N6048 N 3 LCD panel, 17.
LCD FRUs for ThinkPad W701 In ThinkPad W701, there ar e following types of LCDs. v 17.0-in. WXGAx, TFT LCD (T able 63 on page 230) v 17.0-in. WUXGA TFT LCD (T able 64 on page 230) 3 4 5 6 9 10 4 1 8 7.
T able 63. Parts list—17.0-in. WXGA+ TFT No. FRU FRU no. CRU ID 1 LCD cover kit for W701 60Y4915 N 2 LCD bezel 60Y4917 N 3 LCD panel, 17.0-in. WXGA+ v 2500-CTO, 2Bx, 3Ax, 3Hx v 2541-CTO, 2Qx, 58x v 2542-CTO, 58x v 2543-CTO v 2544-CTO v 4323-CTO v 4326-CTO 42T0785 N 3 LCD panel, 17.
T able 64. Parts list—17.0-in. WUXGA TFT (continued) No. FRU FRU no. CRU ID 5 LCD cable assembly for W701 45M2875 N 6 Integrated camera v 2500-CTO, 2Cx, 2Gx, 2Lx, 2Mx, 2Xx, 3Dx, 3Fx, 3Bx, 3Jx, 3Mx, .
LCD FRUs for ThinkPad W701ds 3 4 9 8 6 2 1 14 12 13 11 10 15 5 7 232 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
T able 65. Parts list—17.0-in. WUXGA TFT and 10.6-in. WXGA TFT second screen No. FRU FRU no. CRU ID 1 LCD cover kit for W701ds 60Y4916 N 2 LCD front bezel for W701ds 60Y4917 N 3 LCD panel, 17.
Keyboard T able 66. Parts list—Keyboard Language P/N CRU ID Arabic 42T3212 42T3276 42T3146 ** Belgian 42T3213 42T3277 42T3147 Brazilian Portuguese 42T3240 42T3304 42T3174 Bulgarian 42T4145 42T4142 4.
Miscellaneous parts T able 67. Parts list—Miscellaneous parts FRU P/N CRU ID Screw kit (including nylon-coated scr ews) for W700 and W700ds: v M2 × 2 mm (black), wafer head (8) v M2 × 3 mm (black), wafer head (15) v M2 × 3.5 mm (black), wafer head (40) v M2 × 10 mm (black), wafer head (10) v M2 × 16 mm (black), wafer head (2) v M2.
T able 67. Parts list—Miscellaneous parts (continued) FRU P/N CRU ID Base miscellaneous parts for W701 and W701ds: v Foot rubber (front) v Foot rubber (rear) v Insulation sheet (system board) v Slid.
T able 67. Parts list—Miscellaneous parts (continued) FRU P/N CRU ID System board miscellaneous parts for W701 and W701ds: v Sheet (system board bottom) v Sheet (memory bottom) v Sheet (wireless LAN car d) v Sheet (MXM3 memory) v Bracket, CPU support bracket 60Y4908 N AC adapters T able 68.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: T able 70. Parts list—2-pin power cords (1.0 m) Region P/N CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.
T able 72. Parts list—3-pin power cords (1.8 m) Region P/N CRU ID Argentina v models -CTO, xxY 41R3176 41R3177 * Australia, New Zealand v models -CTO, xxG, xxM 42T5050 42T5135 Bangladesh, Sri Lanka, South Africa v models -CTO, xxG 42T5056 42T5141 Brazil v models -CTO, xxP 45J9595 41R3271 Canada, U.
Recovery discs Windows XP Professional (32 bit) DVDs W indows XP Pr ofessional (32 bit) DVDs are available as the operating system in the following models, however , W indows XP Professional is not pr.
Windows XP Professional (64 bit) DVDs W indows XP Pr ofessional (64 bit) DVDs are available as the operating system in the following models, however , W indows XP Professional is not pr eloaded in the computer: v 2752-CTO v 2753-CTO v 2754-CTO v 2762-CTO v 2763-CTO T able 74.
Windows V ista Business (32 bit) DVDs W indows V ista Business (32 bit) is pr einstalled as the operating system in the following models: v 2752-CTO, 3Ex, 3Lx, 43x, 46x, 5Zx, 66x, 68x, 69x, 6Ax, 6Cx, .
T able 75. Parts list—Windows Vista Business (32 bit) DVDs Language P/N CRU ID Brazilian Portuguese 58Y0016 * Czech 58Y0018 Danish 58Y0019 English 58Y0042 English (modem-disabled) 58Y0041 English, F.
Windows V ista Business (64 bit) DVDs W indows V ista Business (64 bit) is pr einstalled as the operating system in the following models: v 2752-CTO, 36x, 37x, 38x, 3Ax, 3Bx, 3Dx, 3Fx, 3Hx, 3Jx, 3Kx, .
T able 76. Parts list—Windows Vista Business (64 bit) DVDs Language P/N CRU ID Czech 58Y0044 * Danish 58Y0045 English 58Y0066 English (modem-disabled) 58Y0065 English, Finnish, and Swedish (in Swede.
v 2500-CTO v 2541-CTO, 52x v 2542-CTO v 2543-CTO v 2544-CTO v 4323-CTO v 4326-CTO T able 77. Parts list—Windows Vista Business (64 bit) DVDs Language P/N CRU ID English 76Y1993 * English (for India).
Windows V ista Ultimate (64 bit) DVDs W indows V ista Ultimate (64 bit) is pr einstalled as the operating system in the following models: v 2752-CTO, 3Cx, 63x, 64x, ESx, ETx, EVx v 2753-CTO, 6Xx, MHx v 2754-CTO v 2757-CTO v 2758-CTO, 5Ex, 5Hx, 5Jx, M5x v 2762-CTO v 2763-CTO T able 78.
Windows 7 Professional (64 bit) DVDs W indows 7 Professional (64 bit) is pr einstalled as the operating system in the following models: v 2752-CTO v 2753-CTO v 2754-CTO v 2762-CTO v 2763-CTO T able 79.
v 2500-CTO, 2Ax, 2Bx, 2Cx, 2Ex, 2Gx, 2Lx, 2Mx, 2Xx, 3Dx, 3Ex, 3Fx, 3Ax, 3Bx, 3Cx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 3Xx, 3Yx, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x.
T able 80. Parts list—Windows 7 Professional (64 bit) recovery DVDs Language P/N CRU ID Brazilian Portuguese 58Y4990 * Czech 58Y4993 Danish 58Y4994 English 76Y1018 English (for India) 58Y4995 Englis.
Common service tools T able 81. Parts list—Common service tools T ool P/N Screwdriver kit 95F3598 1/4 ″ drive spinner handle 1650840 1/4 ″ Sq. to 1/4 ″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
252 ThinkPad W700, W700ds, W701, and W701ds Hardwar e Maintenance Manual.
Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area.
vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation.
.
Part Number: 43Y9442_06 (1P) P/N: 43Y9442_06.
Ein wichtiger Punkt beim Kauf des Geräts Lenovo W701DS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Lenovo W701DS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Lenovo W701DS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Lenovo W701DS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Lenovo W701DS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Lenovo W701DS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Lenovo W701DS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Lenovo W701DS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Lenovo W701DS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
