Benutzeranleitung / Produktwartung HR-J755EK des Produzenten JVC
Zur Seite of 52
H R-J755EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0042-001A PAL T V P R O G + T V P R O G – T V – T V + 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN.
2 SAFETY FIRST IMPORT ANT n Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder . n It should be noted that it may be unlawful to r.
3 This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. DO read the operating instructions before you attempt to use the equipment.
4 QUICK SET UP GUIDE T V P R O G + T V P R O G – T V – T V + 0000 START DEBUT STOP FIN DATE MENU OK TV PROG TV/VCR DAILY/QTDN. VPS/PDC AUX WEEKLY/HEBDO PROG 30 SEC – –:– – AUDIO 123 456 7 .
5 AV1 IN/OUT AV2 IN R L AUDIO PAUSE ANT. IN RF OUT OUT A V CONNECTION T o Connect T o A TV with 21-pin A V input connector (SCAR T) . . . 1– Connect the aerial, recorder and TV as per “RF CONNECTION”.
6 – –:– – 123 456 7 89 0 2 4 1 3 QUICK SET UP GUIDE (cont.) STEP 3 AUTO SET UP SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL* The Auto Set Up function sets the tuner c.
7 IMPORT ANT n In certain reception conditions, station names may not be stored correctly , and auto Guide Program Number Set may not work properly . If the Guide Program numbers are not set properly , when you timer-record a TV programme using V ideo Plus+, the recorder will record a TV programme of a different station.
8 BASIC OPERA TIONS Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
9 Still Picture/Frame-By-Frame Playback P AUSE DURING PLA YBACK 1 Press P AUSE. If there is vertical jitter , use the TV PROG buttons to correct the picture. ACTIV A TE FRAME-BY -FRAME PLA YBACK 2 T urn the JOG dial to the right for forward frame-by- frame playback, or to the left for reverse frame-by-frame playback.
10 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder . BASIC OPERA TIONS (cont.) Recording T urn on the TV and select the VIDEO channel (or AV mode).
11 Record One Pr ogramme While W atching Another – –:– – 123 456 7 89 0 2 4 1 3 Elapsed Recording Time Indication Y ou can check the exact time of a recording. T ape Remaining T ime DISPLA Y REMAINING TIME 1 Press DISPLA Y (or – –:– – ) until the time remaining on the tape appears.
12 ACCESS VIDEO PLUS+ SCREEN 1 Press PROG . The front display panel looks like this: ENTER PLUSCODE NUMBER 2 Press the NUMBER keys to enter the PlusCode number of the programme you wish to record. ● If you make a mistake, press and input the correct number .
13 SET T APE SPEED 4 Press SP/LP ( ) to set the tape speed. SET PDC MODE 5 Press PDC to select "ON" or "OFF". If "VPS/PDC ON" is displayed on the screen or "VPS/ PDC" is lit on the display panel, PDC is set to ON.
14 – –:– – 123 456 7 89 0 2 4 1 3 OK WEEKLY 7 9 DAILY 6 Express Timer Pr ogramming BASIC OPERA TIONS (cont.) If you don’t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer -record the programme.
15 ENTER PRESET POSITION 6 Press TV PROG +/– to enter the preset position corresponding to the broadcasting station you wish to record. SET T APE SPEED 7 Press SP/LP ( ) to set the tape speed. SET PDC MODE 8 Press PDC to select "ON" or "OFF".
16 BASIC OPERA TIONS (cont.) Check, Cancel And Replace Programmes DISENGAGE TIMER MODE 1 Press ‰ , then press . ACCESS PROGRAMME CHECK SCREEN/DISPLA Y 2 Press . ACCESS PROGRAMME SCREEN/ DISPLA Y 3 Press again to check more information. Each time you press , the next programme's information appears.
17 – –:– – 123 456 7 89 0 2 4 1 3 TV PROG ADV ANCED OPERA TIONS Manual T racking Y our video recorder is equipped with automatic tracking control. For most tapes this will automatically adjust the tracking to suit the particular tape you are playing.
18 Index Search Y our recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode.
19 Instant ReView Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer -recorded programme. If you have several programmes recorded, you can easily access any of them. NOTE: Before starting, make sure that the recorder is off and that the T imer mode is disengaged.
20 ADV ANCED OPERA TIONS (cont.) Playback/ Recording According T o T ape Charac- teristics The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
21 Recording ST AR T RECORDING 1 Press and hold RECORD and press PLAY on the remote, or press RECORD on the recorder . DURING B.E.S.T . B.E.S.T . COMPLETE ● The recorder spends approximately 7 seconds assessing the condition of the tape, then begins recording.
22 Soundtrack Selection Y our video recorder is capable of recording three soundtracks (HI-FI L, HI-FI R and NORM) and will play back the one you select.
23 Spatializer W This feature expands the sound field when you play back any stereo sour ce or view a stereo programme while recording it. *Spatializer W has no effect on recording quality . ACTIV A TE SP A TIALIZER W 1 Press SP ATIALIZER ; the current setting will be displayed on the screen for about 5 seconds.
24 This facility allows you to record automatically a satellite programme which is timer -programmed on your external satellite receiver . Connect a satellite receiver to the recorder's A V2 IN c.
25 A TTENTION ● Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.
26 ADV ANCED OPERA TIONS (cont.) Contr ol Y our TV Using Additional Buttons Use the NUMBER keys, and the button, button or ‰ button to select the TV’ s channel.
27 Satellite Receiver Multi- Brand Remote Contr ol Y our remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’ s satellite receivers can also be controlled. Before you start .
28 – –:– – 123 456 7 89 0 2 4 1 3 ADV ANCED OPERA TIONS (cont.) Edit T o Or Fr om Another V ideo Recorder Y ou can use your video recorder as the source player or as the recording deck. MAKE CONNECTIONS 1 Connect the player’s 21-pin SCAR T connector to the recorder’s 21-pin SCAR T connector as illustrated on the below .
29 – –:– – 123 456 7 89 0 2 4 1 3 Edit Fr om A Camcorder NUMBER "0" TV PROG Y ou can use a camcorder as the sour ce player and your video recorder as the recorder . MAKE CONNECTIONS 1 Connect the camcorder ’ s AUDIO/VIDEO OUT connectors to the recorder ’ s front panel AUDIO/VIDEO input connectors.
30 T urn on the TV and select the VIDEO channel (or A V mode). ADV ANCED OPERA TIONS (cont.) On-Screen Display NOTES: ● When you use this recorder as the player for editing, be sure to set "O.
31 Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on. ACCESS MAIN MENU SCREEN 1 Press MENU . ACCESS MODE SET SCREEN 2 Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or .
32 Repeat Playback Y our video recorder can automatically play back the whole tape 50 times repeatedly . ST AR T PLA YBACK 1 Press PLAY . ACTIV A TE REPEA T PLA YBACK 2 Press PLA Y and hold for over 5 seconds, then release. ● The Play indicator ( ) on the display panel blinks slowly .
33 AV1 IN/OUT AV2 IN R L AUDIO PAUSE ANT. IN RF OUT OUT I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Connection T o A Stereo System These instructions enable you to connect your video recorder to your Hi-Fi stereo system (if you have one) and listen to the soundtrack through the stereo.
34 SUBSIDIAR Y SETTINGS V ideo Channel Set V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable. With A V Connection ACCESS VIDEO CHANNEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following.
35 Before performing the following procedure, make sure that: n the mains power cord is plugged into the mains outlet. n the video recorder is turned off and there is no cassette inserted in the recorder . n the connected TV is turned on. n batteries have been installed in the remote control.
36 – –:– – 123 456 7 89 0 2 4 1 3 SUBSIDIAR Y SETTINGS (cont.) T uner Set IMPORT ANT Perform the following steps only if — — Auto Channel Set has not been set correctly by Auto Set Up function ( Z pg. 6). — you have moved to a different area or if a new station starts broadcasting in your area.
37 VIEW CONFIRMA TION SCREEN 4 After "SCAN COMPLETED" is displayed on the screen for about 5 seconds, a Confirmation screen looking like the one on the right appears. The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – Z pg.
38 SUBSIDIAR Y SETTINGS (cont.) Storing Channels Manually T o s tore channels that were not stored during Auto Set Up ( Z pg. 6) or Auto Channel Set ( Z pg. 36). ACCESS MAIN MENU 1 Press MENU . ACCESS CONFIRMA TION SCREEN 2 Press %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or .
39 Perform steps 1 and 2 of "Storing Channels Manually" on page 3 8 to access the Confirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press % fi until the item you want to move begins blinking. Then press OK and the station name (ID) and its channel (CH) number begin blinking.
40 SUBSIDIAR Y SETTINGS (cont.) % SELECT ST A TION NAME CHARACTER 1 Press until the first letter of the station name begins blinking. ENTER NEW CHARACTER 2 Press %fi to cycle through the characters (A–Z, 0–9, –, * , +, (space) ) and stop when the desired character is indicated, then press to enter .
41 TV Station And ID List ST ATION NAME ID* Anglia TV ANGL ARD ARD ARTE AR TE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BR T1 BRT1 BR T2 BRT2.
42 SUBSIDIAR Y SETTINGS (cont.) TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from the BBC and ITV . BBC1 BBC2 ITV CH4 CH5 London & South-East Bluebell Hill .
43 Just Clock The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set "ON" or "OFF" at the Clock Set screen (the default setting is "ON").
44 V ideo Plus+ Setup SUBSIDIAR Y SETTINGS (cont.) IMPORT ANT Normally , Auto Set Up ( Z pg. 6) or Auto Channel Set ( Z pg. 36 ) sets the Guide Program Numbers automatically . Y ou need to set the Guide Program Numbers manually only in the following cases.
45 PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
46 SUBSIDIARY INFORMA TION (cont.) Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair .
47 CORRECTIVE ACTION Re-perform the clock and/or timer settings. Press ‰ and confirm that “ ‰ “ is displayed on the display panel. T imer programming can’ t be performed while a timer recording is in progress. W ait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.
48 FRONT VIEW SUBSIDIARY INFORMA TION (cont.) REW SP/LP DISPLAY FF TV PROG/ JOG SHUTTLE 3R PICTURE TIMER STANDBY/ON VIDEO (MONO) L –AUDIO– R SPATIALIZER REC LINK TV PROG TV PROG 1 2 3 ^ ) ( * & $ ! # @ 8 9 0 4 5 6 7 % 1 ST ANDBY/ON Button turns recorder on/off (loading a cassette also turns power on).
49 AV1 IN/OUT AV2 IN R L AUDIO PAUSE ANT. IN RF OUT OUT 1 7 5 6 4 3 2 5 A V2 IN Connector enables connection of satellite receiver or second recorder; input recordable when "L-2" selected. Z pg. 24, 28 6 Remote P AUSE Connector enables connection to second recorder equipped with R.
50 REMOTE CONTROL Buttons with a small dot on the left side of the name can also be used to operate your TV . Z pg 26. 1 TV Button enables remote control of your TV . Z pg. 26 2 VCR Button enables remote control of your video recorder . (See A TTENTION on next page) 3 TV/VCR Button switches connected TV's mode between TV and A V .
51 w WEEKLY Button enables timer recording of weekly serials. Z pg. 13, 15 e AUX Button selects recorder's auxiliary input mode. Z pg. 28 r ‰ Button engages timer -standby mode. Z pg. 13, 15 t DA TE +/– Button inputs date of programme for timer recording.
HR-J755EK COPYRIGHT © 1998 VICTOR COMPANY OF JAPAN, LTD. EK Printed in Japan 0398HOV * UN * VP V ICTOR COM P ANY OF JAPAN, LIMITED GENERAL Power requirement : AC 220 – 240 V ` , 50/60 Hz Power consumption Power on : 24 W Power off : 5.
Ein wichtiger Punkt beim Kauf des Geräts JVC HR-J755EK (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC HR-J755EK noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC HR-J755EK - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC HR-J755EK reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC HR-J755EK erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC HR-J755EK besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC HR-J755EK verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC HR-J755EK. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC HR-J755EK gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
