Benutzeranleitung / Produktwartung HR-DD445EK des Produzenten JVC
Zur Seite of 52
H R-DD445EK VIDEO CASSETTE RECORDER INSTRUCTIONS LPT0002-0D7B TM PAL SEE QUICK SET UP GUIDE ON REAR SIDE SEE QUICK SET UP GUIDE ON REAR SIDE SP/ LP q TIMER STANDBY/ON TV PROG COUNTER RESET 1 ¡ ¶ REC 1 4¢ 7 STOP 3 PLAY 8 PAUSE FF ¡ TV 12 3 45 /ADD TIME 6 7 / 8 /DAILY 0 /AUX 9 / WEEKLY TV/VCR (MONITOR) .
2 SAFETY FIRST IMPORT ANT n Please read the various precautions on p. 2 – 3 of this instruction manual before installing or operating the recorder . n It should be noted that it may be unlawful to r.
3 Some Do's And Don'ts On The Safe Use Of Equipment This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
4 INST ALLING YOUR NEW RECORDER Basic Connections RF Cable (provided) CONNECT RECORDER TO MAINS 4 Plug the end of the mains power cord into a mains outlet. Mains outlet Mains Power Cord Back of TV 21-pin AV input connector (SCAR T) It's essential that your video recorder be properly connected.
5 AV1 IN / OUT AV2 IN RF OUT ANT. IN TV Aerial Cable (not provided) A TTENTION If you have finished all the necessary connections, go to "V ideo Channel Set" on page 6, then perform Auto Set Up on page 8; do NOT press the button on the recorder/remote control to turn on the recorder's power before you start Auto Set Up.
6 V ideo Channel Set V ideo Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.
7 IMPORT ANT : Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder . ACCESS VIDEO CHANNEL SET MODE 1 Press and hold down STOP on the recorder until the display panel shows the following.
8 Auto Set Up Auto Channel Set/Auto Clock Set/Auto Guide Program Number Set The Auto Set Up function sets the tuner channels, clock and V ideo Plus+ assigned Guide Program numbers automatically when the button on the recorder/remote is first pressed to power on the recorder after you plug the mains power cord into a mains outlet.
9 Auto Set Up results appear on the display panel ● When both auto channel set and auto clock set have been completed successfully the correct current time will be displayed. ● When auto channel set has been completed successfully but auto clock set has not, "CH" will be displayed.
10 V ideo Plus+ Setup W ith V ideo Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise. NOTE: “Guide Program (GUIDE PROG) number" refers to the assigned TV station numbers, according to broadcast area, for V ideo Plus+ timer recording.
11 When Using A Satellite Receiver And/Or Cable System THE SA TELLITE RECEIVER IS SHOWN CONNECTED TO THE “A V2 IN” (SCAR T) CONNECTOR AND THE CABLE SYSTEM CONNECTED VIA THE AERIAL SOCKET AND TUNED TO, FOR EXAMPLE, PRESET POSITION 6 ON YOUR TV .
12 PLA YBACK Basic Playback The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
13 Playback Features T ake advantage of special functions possible with the recorder ’ s controls or the remote control. q 1 ¡ TV PROG PLAY Still Picture/Frame-By-Frame Playback P AUSE DURING PLA YBACK 1 Press P AUSE. If there is vertical jitter, use the TV PROG buttons to correct the picture.
14 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 Manual T racking Y our video recorder is equipped with automatic tracking control. During playback, you can override this and adjust the tracking manually by pressing the TV PROG buttons. OVERRIDE AUTOMA TIC TRACKING 1 Press on the remote to engage manual tracking.
15 Index Search Y our recorder automatically marks index codes at the beginning of each recording. This function gives you quick access to any one of 9 index codes in either direction. NOTE: Before starting, make sure the recorder is in the Stop mode.
16 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 PLA YBACK (cont.) TimeScan Y our recorder is equipped with the TimeScan function. T imeScan allows noise free pictures to be displayed on your TV screen in the forward and reverse search modes. Audio will be played back at normal speed during any of the TimeScan modes ( Z pg.
17 Names of special-ef fects playback Reverse Forward Search Play Slow-Motion *Still Slow-Motion Play Search -9x -7x -5x -3x -1x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 3x 5x 7x 9x -7x -3x -1/6x -1/18x 0 1/18x 1/6x 1x 2x 5x 9x Audio is output. Audio is not Audio is Audio is not Audio is output.
18 TV signals being received by the recorder ’ s built-in tuner can be recorded onto a video tape. Y ou can “capture” a TV programme using your video recorder . RECORDING Basic Recording T urn on the TV and select the VIDEO channel (or A V mode).
19 Recording Features Record One Pr ogramme While W atching Another SELECT PRESET TO W A TCH 1 Once recording is in progress, all you need to do is to set the preset controls on the TV for the station you wish to view .
20 B.E.S.T . Picture System The B.E.S.T . (Biconditional Equalised Signal T racking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. The default setting for both recording and playback is “ON”.
21 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 q 1 ¡ NOTES: ● The B.E.S.T . system works for both SP and LP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. ● In the case of timer recording, the B.
22 Video Plus+ Timer Recording ACCESS TIMER PROGRAMMING SCREEN 1 Press PROG The front display panel looks like this: ENTER PLUSCODE NUMBER 2 Press the NUMBER keys to enter the PlusCode number of a programme you wish to record. ● If you make a mistake, press CANCEL to backspace and then input the correct number .
23 SET T APE SPEED 4 Press SP/LP ( ) to set the tape speed. RETURN TO NORMAL SCREEN 5 Press OK . ● Repeat steps 1 – 5 for each additional programme. ENGAGE RECORDER’S TIMER MODE 6 Press TIMER . The recorder turns off automatically . NOTE: T o Delay The Stop T ime .
24 Regular Timer Pr ogramming If you don’ t know the PlusCode number for the programme you wish to record, use the following procedure to set your recorder to timer-record the programme. Remember , the clock must be set before you can progamme the timer ( Z pg.
25 ENTER PRESET POSITION 6 Press TV PROG +/– . IMPORT ANT Be sure to confirm the setting of PDC recording. ● If " ON" is displayed on the screen or " " is lit on the display panel, PDC is set to ON. ● If " OFF" is displayed on the screen or " " is not lit on the display panel, PDC is set to OFF .
26 Check And Cancel Programmes ACCESS PROGRAMME DISPLA Y AND/OR SCREEN 1 Press PROG CHECK. ● The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and preset position.
27 Auto Timer When the Auto T imer is set to ON the timer is automatically engaged when the recorder power is turned off and automati- cally disengaged when the recorder is powered back on.
28 RF Cable (provided) VIDEO CHAN- NEL or A V mode 21-pin SCART Cable (not provided) Another recorder Another recorder 21-pin SCART Cable (not provided) Player Y our recorder Y our recorder TV Receive.
29 Y ou can use a camcorder as the sour ce player and your video recorder as the recorder . Edit Fr om A Camcorder ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 MAKE CONNECTIONS 1 Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's rear panel A V2 IN or A V1 IN/OUT connector via the optional cable adapter .
30 AV1 IN / OUT AV2 IN DECODER VCR TV SYSTEM CONNECTIONS Connection T o A Satellite Receiver The A V2 IN socket on the rear panel of your recorder allows simple connection to a satellite receiver . NOTES: ● When connecting your recorder to a TV equipped with 21-pin SCART connectors, follow the illustration above using the cables shown in gray .
31 RF OUT ANT. IN EXT.2 EXT.1 Aerial terminal 21-pin SCART connectors Back of TV.
32 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 T urn on the TV and select the VIDEO channel (or A V mode). The superimposed indication on the TV screen tells you what the recorder is doing. 1– Operation mode indicators 2– Preset position number and station name/Aux.
33 q 1 ¡ ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 FF REW FF REW T ape Position Indicator The tape position indicator appears on screen when, from the Stop mode, you press FF , REW or perform an Index Search. The position of “ 5 ” in relation to “0” (beginning) or “+” (end) shows you where you are on the tape.
34 TUNER SET Auto Channel Set IMPORT ANT Perform the following steps only if auto channel set has not been set correctly by Auto Set Up function ( Z pg.
35 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 VIEW CONFIRMA TION SCREEN 4 The stations your recorder located appear on a Confirmation screen — preset positions (PR), channels (CH) and station names (ID – Z pg. 40). T o view the next page of the listing, press PUSH JOG %fi .
36 Manual Channel Set TUNER SET (cont.) Storing Channels Manually Store channels that were not stored during Auto Set Up ( Z pg. 8) or Auto Channel Set ( Z pg. 34). ACCESS MAIN MENU 1 Press MENU twice. ACCESS CONFIRMA TION SCREEN 2 Press PUSH JOG %fi to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK .
37 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 Perform steps 1 and 2 of "Storing Channels Manually" on page 3 6 to access the C onfirmation screen before continuing. Change Station Preset Position SELECT ITEM 1 Press PUSH JOG % fi until the item you want to move begins blinking.
38 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 Perform steps 1 and 2 of "Storing Channels Manually" on page 3 6 to access the C onfirmation screen before continuing. SELECT ITEM 1 Press PUSH JOG %fi until the item you want begins blinking.
39 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 Perform steps 1 and 2 of "Storing Channels Manually" on page 3 6 to access the C onfirmation screen before continuing. SELECT CHANNEL TO FINE-TUNE 1 Press PUSH JOG % fi until the channel you want to tune begins blinking.
40 TV Station And ID List ST A TION NAME ID* Anglia TV ANGL ARD ARD ARTE AR TE BBC Group BBC BBC1 BBC1 BBC2 BBC2 Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BR T1 BRT1 BR T2 BRT.
41 TV Station Channel Number Guide Only the main stations are listed. There are in addition many relay stations, and full lists are available from BBC and ITC. BBC1 BBC2 ITV CH4 London & South-East Bluebell Hill ............................. 40 46 43 65 Crystal Palace .
42 CLOCK SET IMPORT ANT Perform the following steps only if Auto Clock Set has not been performed correctly by Auto Set Up ( Z pg. 8) or Auto Channel Set ( Z pg.
43 ¶ 1 4¢ 7 3 8 ¡ 12 3 45 6 7 / 8 0 9 4 2 1 3 NOTES: ● Just Clock (when set to "ON") adjusts the recorder's built-in clock every hour , except for 23:00, 0:00, 1:00 and 2:00.
44 TROUBLESHOOTING Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair . POSSIBLE CAUSE ● The mains power cord is discon- nected.
45 CORRECTIVE ACTION Re-perform the clock and/or timer settings. Press TIMER and confirm that “ ‰ “ is displayed on the display panel. T imer programming can’t be performed while a timer recording is in progress. W ait until it finishes. Load a cassette with the Record Safety tab intact, or cover the hole using adhesive tape.
46 QUESTIONS AND ANSWERS PLA YBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
47 GENERAL Power requirement : AC 220 – 240 V ` , 50/60 Hz Power consumption : 20 W T emperature Operating : 5°C to 40°C Storage : –20°C to 60°C Operating position : Horizontal only Dimensions (WxHxD) : 400 x 94 x 340 mm W eight : 4.3 kg Format : VHS P AL standard Maximum recording time (SP) : 240 min.
48 FRONT VIEW INDEX SP/ LP q TIMER STANDBY/ON TV PROG COUNTER RESET 1 ¡ 2 5 8 7 6 1 3 4 9 ! @ 0 # $ % ^ 1 TIMER Button engages timer standby mode. Z pg. 23, 25 2 ST ANDBY/ON Button turns recorder on/off (loading a cassette also turns power on). Z pg.
49 REAR VIEW AV1 IN / OUT AV2 IN RF OUT ANT. IN 3 2 4 5 1 4 A V2 IN Connector enables connection of satellite receiver or second recorder; input recordable when "AU 2" selected. Z pg. 30, 28 5 RF OUT Connector enables connection to aerial terminal of TV receiver .
50 ¶ REC 1 4¢ 7 STOP 3 PLAY 8 PAUSE FF ¡ TV 12 3 45 /ADD TIME 6 7 / 8 /DAILY 0 /AUX 9 / WEEKLY TV/VCR (MONITOR) . CANCEL /C.RESET PROG CHECK 4 TIMER TV PROG DATE STOP START PROG /MENU OK C.MEMORY TV VOL TV VOL DISPLAY 2 1 3 EXPRESS PROGRAMMING PUSH JOG Press and hold TV button while pressing , TV PROG.
51 w SP/LP Button selects tape speed. Z pg. 18 Auto T racking Button enables/disables auto tracking mode during playback Z pg. 14 e TIMER Button — same as button on recorder . Z pg. 23, 25 r DA TE +/– Button inputs date of program for timer recording.
VICTOR COMP ANY OF JAPAN, LIMITE D.
Ein wichtiger Punkt beim Kauf des Geräts JVC HR-DD445EK (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC HR-DD445EK noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC HR-DD445EK - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC HR-DD445EK reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC HR-DD445EK erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC HR-DD445EK besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC HR-DD445EK verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC HR-DD445EK. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC HR-DD445EK gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
