Benutzeranleitung / Produktwartung Modero MVP-8400i des Produzenten AMX
Zur Seite of 214
Operation/Reference Guide Touch Panels MVP-8400i 8.4" Modero ® ViewPoint ® Touch Panel with Intercom Last Revised: 4/1/2011.
AMX Limited Warranty and Disclaimer This Limited W arranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partn er which include AMX Dealers, Distributors, VIP’s or other AMX authorized entity .
AMX Software License and Warranty Agreement • LICENSE GRANT . AMX grants to Licensee the non-exclusive right to use the AMX Software in the manner described in this License. The AMX Software is licensed, no t sold. This license does not grant Licensee the right to create derivative wor ks of t he AMX Software.
FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the fol lowing two condition s: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding in terference that may cause undesi red operation.
Table of Contents i MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom Table of Contents MVP-8400i Modero Viewpoint Wireless To uch Panel With I ntercom ................. 1 Overview .............................. .....................
ii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Step 3: Choose a Master Connection Mode ........ ................... ......................... ....... 27 USB........... ............. ................. .........
Table of Contents iii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom EAP-TLS Settings ........ ............. ............. ................ ............. ............. ................ ............. .. 79 Client certifi cate config uration .
iv MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Overview ........... ......................... .................... ................... .................... ............... 107 Button Assignments ..............
Table of Contents v MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom ^BNP ......... ............... ............ ............ ........... ............... ............ ............ ........... ............ .. ............ 127 ^BNT ..
vi MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents ^UNI ............... ........... ............ ............ ............... ........... ............ ............ ............ ........... ............ 139 ^VTP ..
Table of Contents vii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom PKEYP ............. ............ ............ ............... ........... ............ ............ ............... ........... ......... ... ........ 156 @PKP .
viii MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents ^RSR ............... ........... ............ ............... ............ ........... ............ ............... ............ ........ ... ......... 166 Escape Sequences .
Table of Contents ix MVP-8400i 8.4" Modero® ViewPoint® Touch Panel w ith Intercom ^PHN-SETUP-PROXYADDR ........ ............ ........... ............... ............ ............ ........... ............... ..... 173 ^PHN-REDIAL ..... .........
x MVP-8400i 8.4" Modero® ViewPoint® Touch Panel wit h Intercom Table of Contents Only One Mode ro Panel in My System Shows U p .................. ............. ................ ........ 196 Panel Behaves S trangely After Downloa ding a Panel F ile or Firmware .
MVP-8400i Modero Viewpoint Wireless Touch Panel With Int ercom 1 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Modero Viewpoint Wireless Touch Panel With Intercom Overview The MVP-8400i Modero V iewpoint W ireless T ouch Panel ( FIG.
MVP-8400i Modero Viewpoint Wireless Touch Panel With Interco m 2 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Optional AMX accessory solutions for the MVPs include MVP-TDS T able T op Dockin g Station (see the MVP-TDS T able T op Docking Station Operation/Refer ence Guide for details).
MVP-8400i Modero Viewpoint Wireless Touch Panel With Int ercom 3 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Specifications (FG 5965-04) (Cont.) Power Modes: • ON: Panel is fully functional. • ST AN DBY : Panel uses low power, the L CD/backlight is shut down, LEDs still function.
MVP-8400i Modero Viewpoint Wireless Touch Panel With Interco m 4 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-8400i Specifications (FG 5965-04) (Cont.) Internal Components (Cont.): Button Assignments: Button assignments can only be adjusted in TPD4 and not on the panels.
MVP-BP Power Pack 5 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP-BP Power Pack Overview The MVP-BP Po wer Pack ( FG5965-20 ) is a rechargeable Lithium-Ion ba ttery used to provide power to the MVP touch panels. T wo MVP-BPs are included with each MVP-8400i touch panel.
MVP-BP Power Pack 6 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 4. T o replace the battery compartme nt cov er , use the alignment guide holes to align the cov er with the edges of the battery compartment, and slid e it back i nto place until it snaps shut.
NXA-CFSP Compact Flash 7 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom NXA-CFSP Compact Flash Overview Every MVP panel is shipped with a 128 MB Compact Flash c ard. Compact Flash Card - Security All security user names and passwords (for the docki ng station) are stored in the Co mpact Flash card.
NXA-CFSP Compact Flash 8 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. Grasp the bottom rim of the rear housing just above the MVP interface connector , and carefully pull the bottom rim aw ay from the IR Emitter and up, to e xpose the internal components.
NXA-CFSP Compact Flash 9 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 2. Place the circuit board on a flat le vel surf ace so that the IR Emitters are pointing aw ay from you ( FIG.
NXA-CFSP Compact Flash 10 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Panel Calibration 11 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Calibration This section outlines the steps for calibrating the touch panel. It is r ecomme nded that you calibrate the panel both befor e its initial use and after completing a f irmwar e download.
Panel Calibration 12 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. After the " Calibration Successful. " message appears, press anywhere on the screen to continue and return to the Setup page. Testing your Calibration 1.
Configuring Communications 13 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring Communications Communication between the MVP and the Master consists of using either W ireless Ethernet (DHCP , Static IP) or USB. References to Ethernet in this manual focus on the use of W ireless Ethernet via the MVP’ s WiFi Card.
Configuring Communications 14 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the Panel’ s Device Number In the Pr otec ted Setup page: 1.
Configuring Communications 15 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring a Wireless Network Access When working with a wireless card, the first step is to conf igure wireless communication parameters within the W ireless Settings page.
Configuring Communications 16 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Setup the security and communication parame ters between the wireless card and the target W AP by configuring the W ir eless Settings section on this page.
Configuring Communications 17 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 2. In the lower -right corner of the W ireless Settings page, press the Simple b utton to open the Wi re l e s s Security: Simple Mod e window ( FIG. 15 ).
Configuring Communications 18 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom select between WEP Ke ys 1 through 4, and press the A uthentication field to select between Open and Shared. When se lecting WP A-PSK as a Security T ype, only the SSID and Pa s s w o r d fields are enabled.
Configuring Communications 19 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Provisioning is Disabled; if it is Enabled, se lect between NEVER, 1 Da y , 3 Days, 7 Days, 14 Days, or 30 Days. 3. When f inished , press the Sa ve button to sa ve all changes and return to the W ir eless Settings page.
Configuring Communications 20 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom If a W AP displayed in th e list is not detected for 10 scans in a row , it is then removed from the screen. In this w ay , a user can walk around a b uilding and see access points come and go as th ey mov e in and out of range.
Configuring Communications 21 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring the Modero ’s wireless card for unsecured access to a WAP200G In the Pr otec ted Setup page: 1. Press the Wir eless Settings button (located on the upper-left) to open the W ir eless Settings page.
Configuring Communications 22 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 4. Press the red SSID f ield to display the on-screen Netwo rk Name (SSID) keyboard. 5. In this keyboard, enter the SSID name used on your tar get W ireless Access Point ( case sensitiv e ).
Configuring Communications 23 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configuring the Mo dero’s wireless ca rd for secured access to a WAP200G After logging into the W AP200G, the default Status page appears within the web bro wser .
Configuring Communications 24 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Manually set SSID In the Pr otec ted Setup page: 1. Select Wir eless Settings . 2. In the IP Settings section, press the DHCP/Static field until it reads "Static".
Configuring Communications 25 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The card should be gi ven the SSID used by the tar get W AP . If this field is left blank, the unit will attempt to connect to the first a vailable W AP .
Configuring Communications 26 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 9. The Curr ent K e y field is gre yed-out and cannot be altered by the user . The Authentication f ield may be switched from Open to Shared. 10. When f inished, press the Sa ve button to sa ve all changes and return to the W ir eless Settings page.
Configuring Communications 27 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Step 3: Choose a Master Connection Mode The panel requires you establish the type of connection you want made between it and your master . In the Pr otec ted Setup page: 1.
Configuring Communications 28 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom panel is recognized as a unique USBLAN device, and the association to the driv er is handled automatically . 1. Connect the PS4.4 power connector to the panel (or docking station if the panel is already installed) to supply power .
Configuring Communications 29 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Configure a Vir tual NetLinx Maste r using NetLinx Stu dio A V irtual NetLinx Master (VNM) is u sed when the target panel is not connected to a physical NetLinx Master .
Configuring Communications 30 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 3. Click the Communications Settings button to open the Communications Settings dialog. 4. Click the NetLinx Master radio button ( fr om the Platform Selection section ).
Configuring Communications 31 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Master Connection to a Virtua l Master via Ethernet Before beginning: 1. V erify the panel has been configured to communica te with the W ireless Access Point and verify the signal strength quality bargraph is On.
Configuring Communications 32 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the OnLine T ree tab in the W orkspace window to view the de vices on the V irtual System. The default System value is one . 11. Right-click on the Empty Device T r ee/System entry and select Refresh System to re-populate the list.
Configuring Communications 33 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using G4 Web Control to Interact with a G4 Panel The G4 W eb Control feature allows you to use a PC to interact with a G4 enabled panel via the web .
Configuring Communications 34 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 9. From the W eb Name keyboard, enter a unique alpha-numeric string to identify this panel. This information is used by the NetLinx Security W eb Se rver to display on-screen links to the pane l.
Configuring Communications 35 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using your NetLinx Master to control the G4 panel Refer to your particular NetLinx Master’ s instruction manual for detailed information on how to download the latest f irmware from www .
Configuring Communications 36 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Click on the G4 panel name link associated with the target panel.
Configuring Communications 37 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Enter the W eb Control session password into the Session P assword field ( FIG. 34 ). This passwor d was pr eviously enter ed into the W eb Contr ol P assword f ield within the G4 W eb Control pa ge on the panel.
Configuring Communications 38 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Upgrading MVP Firmw are 39 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Upgrading MVP Firmware Except for the MVP-KS (Kickstand for MVP Panels), all MVP panels and their accessories hav e on- board firmw are which is upgra deable through the use of the latest NetLinx Studio.
Upgrading MVP Firmware 40 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Upgrading the Modero Fi rmware via the USB port Before beginning with this section, verify your panel is po wered and the T ype-A USB connector is securely inserted into the PC’ s USB port.
Upgrading MVP Firmw are 41 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Click the Edit Settings button ( on the Communications Settings dialog ) to open the V irtual NetLinx Master Settings dialog ( FIG. 35 ). 7. From within this dialog enter the System num ber (default is 1 ).
Upgrading MVP Firmware 42 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 5. If the panel firmw are version is not the latest a v ailable; locate the latest firmw are file from the www .amx.c om > T ech Center > Downloadable Files > Firmware Files > Modero Panels section of the website.
Upgrading MVP Firmw are 43 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r e boot of the panel can take up 30 seconds after the f irmwar e process has finished.
Upgrading MVP Firmware 44 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 1. Complete the instructions for configuring the NetLinx Master for IP communication found in the Upgrading the Moder o Firmwar e via the USB port section on page 40.
Upgrading MVP Firmw are 45 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r e boot of the panel can take up 30 seconds after the f irmwar e process has finished.
Upgrading MVP Firmware 46 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Although firmware u pgrades can be done over wireless Ethernet; it is recommended that firmware KIT files be transfer red over a direct USB connection and only when the panel is connected to a power supply .
Setup Pages 47 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setup Pages AMX Modero panels feature on-board Setup pages. Us e the options in th e Setup pages to access panel information and make various conf iguration changes.
Setup Pages 48 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setup Pages The Setup page ( FIG. 43 ) allows quick access to se veral basic panel properties: Features on this page include: FIG.
Setup Pages 49 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Settings The Pr otected Settings page and its contents are cove red in more detail in the Pr otected Setup Pa g e s section on page 60.
Setup Pages 50 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Project Informati on Page The Project Information page d isplays the project properties of the TPDesign4 project file currently loaded on the panel ( FIG. 45 ). Features on this page include: FIG.
Setup Pages 51 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Project Information Page (Cont.) IR User Def 1 Port: Displays the User Defined IR channel port used by the IR Emitter on the panel. • Note : User Defined ports can be downloaded by the user and are customizable, whereas the AMX ones are fixed.
Setup Pages 52 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Information Page The Panel Information page provides detailed panel information ( FIG. 46 ). Features on this page include: FIG. 46 Panel Information page Panel Information Page Back: Saves all changes and returns to the previous page.
Setup Pages 53 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Information Page (Cont.) Screen Refresh Rate: Displays the video refresh rate applied to the incoming video sign al from the panel. Screen Rotation: D isplays the degree of rotation applied to the on-screen image.
Setup Pages 54 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Time & Date Settings The options on the T ime & Date Settings page ( FIG.
Setup Pages 55 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Time & Date Settings Page (Cont.) Set Date/Time: Use the UP/DN arrow buttons to adjust the Maste r ’s calendar date and time. The blue icon indicates which fiel d is currently selected (see FIG .
Setup Pages 56 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Audio Settings The MVP-8400i provides an Audio Settings page ( FIG. 48 ) with options that allow you to adjust v olume lev els, set intercom sou nd and microphone lev e ls, and set panel sounds.
Setup Pages 57 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom En vironmental acoustics, personal voice le vel and am bient noise are all deciding factors when setting your mic, intercom and panel sound lev els. Consider your en vironment when adjusting intercom and sound lev els and use cau tion so as not to damage the speaker .
Setup Pages 58 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Battery Settings The options on this page allow you to set po wer warning preferences, monitor battery status information, and adjust the display times for battery warnings.
Setup Pages 59 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Battery Settings Page (Cont.) Low Battery Warning: The UP/DN buttons adjust the time value (in minutes) available on the battery (for use) before the panel displays a low battery warning.
Setup Pages 60 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Pages The Protected Setup page ( FIG. 50 ) provides secured access to a dvanced panel conf iguration options, including communication and security settings.
Setup Pages 61 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Page (Cont.) Docking Station: • Dock Status - illuminates when the MVP is docked and communicating with the Docking S tation. • Undock Panel - forces the docking station to release the MVP without requiring a User Access username or password.
Setup Pages 62 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Protected Setup Navigation Buttons The Protected Setup Navigation Buttons ( FIG. 52 ) appear on the left of the panel screen when the Protected Setup page is currently activ e.
Setup Pages 63 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom System Settings Page The System Settings page ( FIG. 53 ) displays sets the NetLinx Master’ s commun ication settings.
Setup Pages 64 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the Step 3: Choose a Master Connection Mode section on page 27 for more detailed information on using the System Settings page. System Settings Page Elements Master Connection (Cont.
Setup Pages 65 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Wireless Settings Page Use the options on the Wireless Settings page ( FIG. 54 ) to conf igure communication settings for the wireless CF card (802.11g), and read the de vice number assigned to the panel.
Setup Pages 66 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Pressing the Simple or Enterprise b uttons at the bottom of the Information/Configur ation section open an appropriate W ireless Security window for Simple Mode or Enterprise Mode.
Setup Pages 67 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom FIG. 55 Wireless Security: Simple Mode Wireless Security: Simple Mode Security T ype: This field may be switched between WEP , WP A-PSK, and Open. If WEP is selected, the button to the right may be switched between 64 and 128 .
Setup Pages 68 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom FIG. 56 Wireless Security: En terprise Mode Wireless Security: Enterprise Mode Security T ype: Pressing this field changes the secu rity type being used between EAP-PEAP , EAP-TTLS, EAP-TLS, EAP-LEAP , and EAP-F AST .
Setup Pages 69 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Wireless Settings The options on the W ir eless Secur ity: Simple Mode and W ir eless Security: Enterprise Mode windows allow you to select from the wireless security methods supported b y the NXA-WC802 11GCF W i-Fi card.
Setup Pages 70 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Open Settings Open security does not utilize any encryption methodology , but requires an SSID (alpha-numeric) entry . This entry must match the Network Name (SSID) en try of the target W AP so the panel kno ws what de vice it is using to communicate with the network.
Setup Pages 71 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom WEP Settings (Cont.) Generate (Passphrase): This button displays an on-screen keyboar d which allows you to enter a passphrase. The panel then automat ically generates four WEP keys (compatible only with Modero panels).
Setup Pages 72 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the Configuring a W ir eless Network Access section on page 15 for further details on these security options. Refer to the Using the Site Survey tool section on page 19 for more information on using this feature.
Setup Pages 73 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-LEAP Setting s EAP (Extensible Authentication Protocol) is an Enterprise authentication protocol that can be used in both wired and wireless network en vironments. EAP requires the use of an 802.
Setup Pages 74 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-FAST Settin gs EAP-F AST (Flexible Authentication via Secure T unneling) security was designed for wireless en vironments wh ere security and ease of setup are e qually desirable.
Setup Pages 75 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the EAP Authentication section on page 185 for further details on these security options. Refer to the Using the Site Survey tool section on page 19 for more information on using this feature.
Setup Pages 76 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the EAP Authentication section on page 185 for further details on these security options. Refer to the Using the Site Survey tool section on page 19 for more information on using this feature.
Setup Pages 77 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-TTLS Setting s TTLS (EAP T unnele d T ransport Layer Security) is an authentication method that does n ot use a client certificate to authenticate the panel. Howe ver .
Setup Pages 78 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the EAP Authentication section on page 185 for further details on these security options. Refer to the Using the Site Survey tool section on page 19 for more information on using this feature.
Setup Pages 79 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP-TLS Settings TLS (T ransport Layer Security) was the original st andard wireless LAN EAP au thentication protocol.
Setup Pages 80 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the EAP Authentication section on page 185 for further details on these security options. Refer to the Using the Site Survey tool section on page 19 for more information on using this feature.
Setup Pages 81 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom It is important to note which certificate types are supported by the different certificate f ield s used on the configuration screens (PEAP , TTLS, and TLS). The following table outlines the f irmware fields and their supported certificate types.
Setup Pages 82 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom G4 Web Control Settings Page An on-board VNC (V irtual Network Computing) server allo ws the panel to connect to any remote PC running a VNC client. Once connected, the client can vie w and control the panel remotely .
Setup Pages 83 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom G4 Web Control Page ( Cont.) Current Connection Count Displays the number of users currently connected to this panel via VNC.
Setup Pages 84 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Other Settings The Other Settings button provides a menu to select the Image Cac h ing page, P asswor d Setup page, or SIP Settings page. Select any option to access its page.
Setup Pages 85 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom the situation, as the panel could spend more resour ces processing information rather than continuously waiting on images to arriv e from a slow network.
Setup Pages 86 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the image cache In the Pr otec ted Setup page: 1. Press the Cache b utton in the Protected Setup Navigation Buttons section. This opens the Cache Settings page. 2.
Setup Pages 87 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Password Settings Pag e The options on the P asswor d Settings page enable you to assign the passwords required for users to access the Pr ote cted Setup page, and to release the MVP from a MVP-TDS or MVP-WDS docking station ( FIG.
Setup Pages 88 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Password Settings Page (Cont.) User Access: Use these buttons to access and modify the user name/password combinations required for removing the panel from a docking station.
Setup Pages 89 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Settings Page The options on the SIP Settings page ( FIG. ) enable you to establish network settings for using your touch panel as an IP phone.
Setup Pages 90 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Settings Page (Cont.) Stat u s: T his option enables the SIP S tack on startup. If you disable this option, the panel will not attempt to read the rest of the configuration and will not register with a proxy server.
Setup Pages 91 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Tools The T ools button provides a menu to select either the P ane l Connection Logs P age section on page 91 , the P anel Statistics P age section on page 93 , or the Connection Utility P age section on page 95 .
Setup Pages 92 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Features on this page include: Checking the Panel Connection Logs 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu.
Setup Pages 93 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Statisti cs Page The options on the Panel Statistics page allo w you to track the connection status for the panel. The P anel Statistics page tracks ICSP messages, Blink messages, Ethernet connection statistics, and W irele ss connection statistics ( FIG.
Setup Pages 94 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Checking the Pa nel Statistics 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Panel Statistics button.
Setup Pages 95 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Connection U tility Page The options on the Connection Utility page allow you to utilize your panel as a site surv ey tool.
Setup Pages 96 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Using the Connection Utility 1. Press the T ools button in the Pr otected Setup Navigation Buttons section. This opens the T ools menu. 2. W ithin the T ools menu, press the Connection Utility button.
EAP Security & Server Certifica tes 97 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP Security & Server Certificates Overview The follo wing EAP types all support a ser.
EAP Security & Server Certificates 98 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Full Duplex Intercom 99 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Full Duplex Intercom Overview V oIP technology giv es users the ability to instantly create a high-quality , digita l home/off ice intercom network with no additional equipment required.
Full Duplex Intercom 100 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Setting the Intercom Session Timeout 1. Select the Setup button on your intercom page. 2. Press the up or down arro ws to increment the timeout up by 1 second in each direction.
Full Duplex Intercom 101 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Advanced Setup The intercom’ s advanced setup pages are accessed through the intercom setup pages. The advanced pages allow you to set the panel intercom to be monito red, to monitor other intercom panels, and to name the panel.
Full Duplex Intercom 102 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 5. Press Back to return to the intercom setup pages. 6. Press Exit when you are finished. Allowing a panel to mo nitor 1. Select the Setup button on your intercom page.
Full Duplex Intercom 103 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Sample Intercom Page The module for duplex intercom capable panels includes user pages. While you can create your o wn intercom directory page (see Cr eating Intercom P ages section on page 106 ), it is possible to use the panel with the page below .
Full Duplex Intercom 104 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Sample Intercom Page ( Cont.) No. Name Descri ption Channel Po r t:Code Address Port:Code Level Port:Code 7 Panel Directory Room Name The name of a panel in the intercom directory .
Full Duplex Intercom 105 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Answering an incomi ng call The provided intercom pages include an answering popup window . The popup page indicates the name of the panel calling and two options: Answer - Pressing this button opens the intercom session with the o ther panel.
Full Duplex Intercom 106 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Creating Intercom Pages The easiest method of creating your o wn intercom pages is to start with the pages pro vided by AMX in the module download .
Programming 107 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Programming Overview Y ou can program the touch panel, using the comma nds in this section, to perform a wide variety of operations using Send_Commands and variable text commands.
Programming 108 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) @CPG Clear all popup pages from specified popup group. Syntax: "'@CPG-<popup group name>'" Va r i a b l e : popup group name = 1 - 50 ASCII characters.
Programming 109 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont.) @PHT Set the hide effect time for the specified popup page. Syntax: "'@PHT-<popup page name>;<hide effect time>'" Va r i a b l e : popup page name = 1 - 50 ASCII characters.
Programming 110 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) @PPK Kill a specific popup page from all pages. Kill refers to the deactivating (Off) of a popu p window from all pages. If the pop-up p age is part of a group, the whole group is deactivat ed.
Programming 111 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont.) @PPX Close all popups on all pages. This command works in the same way as the 'Clear All' command in T PDesign 4.
Programming 112 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Page Commands (Cont. ) PPOF Deactivate a specific popup page on either a specified page or the current page. If the page name is empty , the cu rr ent page is used (see example 2).
Programming 113 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Programming Numbers The follo wing information provides the program ming numbers for colors, fonts, and borders. Colors can be used to set the colors on buttons, sliders, and pages.
Programming 114 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom RGB Values for all 88 Basic Colors (Cont.) Index No . Name Re d Green Blue 36 V ery Light Cyan 0 255 255 37 Light Cya.
Programming 115 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Font Styles and ID Numbers Font styles can be used to program the text font s on buttons, sliders, and pages. The follo wing chart shows the def ault font type and their respectiv e ID numbers generated by TPDesign4.
Programming 116 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Border Styles and Programming Numbers Border styles can be used to program bor ders on bu ttons, sliders, and popup pages. The TPDesign4 T ouch Panel Design program has pre- set border styles that are user selectable.
Programming 117 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom TPD4 Border Styles by Name (Cont.) No. Border styles No. Border styles 43 Diamond 85 85 Menu Bottom Rounded 65 44 Dia.
Programming 118 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands These Button Commands are used in NetLinx Studio and are case insensiti ve. All commands that begin with " ^ " hav e the capability of assigning a variable te xt address range and button state range.
Programming 119 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^APF Add page flip action to a button if it does not already exist. Syntax: "'^APF-<vt addr range>,<page flip action>,<page name>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 120 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BCB Set the border color to the specified color . Only if the specified border color is not the same as the curr ent color .
Programming 121 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BDO Set the button draw order .
Programming 122 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BLN Set the number of lines removed equally from the top and bottom of a composite video signal. The maximum number of lines to remove is 240.
Programming 123 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BMC (Cont.) Example 2: SEND_COMMAND Panel,"'^BMC-150,1,1,315,1,%BR%F.
Programming 124 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BMF (Cont.) For some of these commands and v alues, ref er to theRGB V alues for all 88 Basic Colors table on page 113. ’%CF<on fill color >’ = Set Fill Co lor .
Programming 125 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BMI Set the button mask image. Mask image is used to crop a borderless button to a non-square shape. This is typically used with a bitmap.
Programming 126 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BNN Set the T akeNote network name for the specified Addresses. Syntax: "'^BNN-<vt addr range>,<network name>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 127 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BOR Set a border to a specific border style associated with a border value for those buttons with a defined address range. Refer to the Border Styles and Programming Numbers table on page 11 6 for more information.
Programming 128 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BRD Set the border of a button state/ states. Only if the specified border is not the same as the curr ent border . Th e border names are available through the TPDesign4 border-name drop-down list.
Programming 129 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^BSP Set the button size and position.
Programming 130 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^BWW Set the button word wrap feature to those buttons with a defined address range.
Programming 131 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^ENA Enable or disable buttons with a set variable text range. Syntax: "'^ENA-<vt addr range>,<command value>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 132 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^GIV Invert the joystick axis to move the origin to another corner . Parameters 1,2, and 3 will cause a bargraph or slid er to be inverted regardless of orientation.
Programming 133 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^GSC Change the bargraph slider color or joysti ck cursor colo r . A user can also assign the color by Na me and R,G ,B value (RRGGBB or RRGGBBAA).
Programming 134 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^IRM Set the IR channel. Pulse the given IR channel for onTime in tenths of seconds. Delay offT ime in tenths o f a second before the next IR pulse is allowed.
Programming 135 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^JSI Set icon alignment using a numeric keypad layout for those buttons with a defined address range. The alignment of 0 is followed by ',<left>,<top> '.
Programming 136 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont .) ^MDC T urn On the ’Mouse double-click’ feature for the virtual PC.
Programming 137 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom "^" Button Commands (Cont.) ^TEC Set the text effect color for the specified addresses/states to the specified color . The T ext Effect is specified by name and c an be found in TPD4.
Programming 138 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Miscellaneous MVP Stri ngs back to the Master The following tw o strings are sent by the MVP panel back to the communicating Master: "^" Button Commands (Cont .
Programming 139 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom MVP Panel Loc k Passcode c ommands These commands are used to maintain a passcode list. From certain panels a password must be entered to remov e the panel from its cradle.
Programming 140 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Text Effects Names The following is a listing of text ef fects names (associated with the ^TEF command on page 138 ).
Programming 141 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands Button Query commands reply back with a custom ev ent. There will be one custom e vent for each button/state combination. Each query is assigned a unique custom e vent type.
Programming 142 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom These fields are populated dif ferently for each query command. The text length (String Encode) f ield is not used in any command. Button Query Commands ?BCB Get the current border color .
Programming 143 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BCF Get the current fill color . Syntax: "'?BCF-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 144 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BMP Get the current bitmap name. Syntax: "'?BMP-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 145 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BRD Get the current border name. Syntax: "'?BRD-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 146 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?BWW Get the current word wrap flag status. Syntax: "'?BWW-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 147 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?FON Get the current font index. Syntax: "'?FON-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 148 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?JSB Get the current bitmap justification. Syntax: "'?JSB-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 149 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?JST Get the current text justification. Syntax: "'?JST-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 150 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?ST A Dump XML Panel St a t s Syntax: "'?STA'" Returned in MUL TIPLE Custom events (size of strings are limited per message).
Programming 151 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?TEF Get the current text effect name. Syntax: "'?TEF-<vt addr range>,<button states range>'" Va r i a b l e : variable te xt address range = 1 - 4000.
Programming 152 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Button Query Commands (Cont.) ?V O L Show the Master Vo l u m e information.
Programming 153 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operations Serial Commands are used in the AxcessX T erminal Emulator mode. These commands are case insensitiv e. Panel Runtime Op eration Commands ABEEP Output a single beep even if beep is Off.
Programming 154 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @AKP Pop up the keypad icon and initialize the tex t string to that specified. Keypad string is set to null on power up and is stored until power is lost.
Programming 155 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @EKP Extend the Keypad. Pops up the keypad icon and initializes the text string to that specified. The Prompt T ext is optional.
Programming 156 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) @SOU Play a sound file. Syntax: "'@SOU-<sound name>'" Va r i a b l e s : sound name = Name of the sound file.
Programming 157 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Runtime Operatio n Commands (Cont.) TP A GEON T urn On page tracking. This command turns On page tracking, whereby when the page or popups change, a string is sent to the Master .
Programming 158 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Input Commands These Send Commands are case insensitive. Input Comman ds ^CAL Put panel in calibration mode. Syntax: "'^CAL'" Example: SEND COMMAND Panel,"'^CAL'" Puts the panel in calibration mode.
Programming 159 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Input Command s (Cont.) ^MPS Set mouse pass through. Allows mouse input to multiple destinations simultaneously .
Programming 160 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Embedded codes The following is a list of G4 compatible embedd ed codes: Embedded Codes Decima l nu m ber s Hexidecim.
Programming 161 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands These commands are case insen sitiv e. Panel Setup Commands CLOCK Sets the time and date on the panel.
Programming 162 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands (Cont.) ^CFSM Sets the Flash cache to the maximum available size allowed for backup Flash cache. (determined by taking 75% of free Flash space) Syntax: “’^CFSM’” V ariable: There is no parameter for this command.
Programming 163 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Setup Commands (Cont.) ^ICM-SPEAKERLEVEL Set the speaker level during an intercom call.
Programming 164 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Dynamic Image Commands The following table describe s Dynamic Image Commands. Panel Setup Commands (Cont.) ^V OL Set the panel volume. Syntax: "'^VOL-<volume level>'" V ariable: volume le vel = 0 - 100.
Programming 165 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom ^RAF, ^RMF - Embedded Codes The ^RAF and ^RMF commands add and modify any and all resource pa rameters by sending emb.
Programming 166 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Escape Sequences The ^RAF and ^RMF commands support the replacement of any special escape se quences in the filename .
Programming 167 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom For in st an c e, http://www .amx.com/i mg.asp?de vice=$DV would become http://www .amx.com /img.asp?device=10001. Intercom Commands The following is a listing and descriptions of panel intercom commands.
Programming 168 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Intercom Co mmands (C ont.) ^ICS S tarts an intercom call to the specified IP address and ports. ^ICS-<IP>,<TX UDP port>,<RX UDP port>,<initial mode>'" Intercom start.
Programming 169 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands The following table lists and describes SIP comma nds that are generated from the touch panel. SIP Commands ^PHN- A UTO ANSWER Provides the state of the auto-answer feature.
Programming 170 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The following table lists and describes SIP commands that are sent to the touch panel to manage calls. SIP Commands (Cont.) ^PHN- MSGW AITING Indicates the number of messages waiting the user ’s voice mail box.
Programming 171 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands (Cont.) ?PHN- A UTO ANSWER Queries the state of the auto-answer feature.
Programming 172 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The following table lists and describes SIP setup commands. Using any of these commands ca uses the current user to go offline. SIP Commands (Cont.) ^PHN-REDIAL Redials the last number .
Programming 173 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom SIP Commands (Cont.) ^PHN-SETUP- STUNADDR Sets the IP address for the STUN server . Syntax: "’^PHN-SETUP-STUNADDR,<IP>’" Va r i a b l e : IP = The IP address for the STUN server Example: SEND_COMMAND Panel,"’^PHN-SETUP-STUNADDR,192.
Programming 174 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Appendix A: Text Formatti ng 175 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix A: Text Formatting Text Formatting Codes for Bargraphs/Joysticks T ext formatting codes for.
Appendix A: Text Formatting 176 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Text Area Input Masking T ext Area Input Masking can be used to limit the allo wed/correct characters that are entered into a te xt area.
Appendix A: Text Formatti ng 177 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Refer to the following Send Commands for more detailed information: Input mask ranges These ranges allow a user to specify the min imum and maximum numeric value for a field.
Appendix A: Text Formatting 178 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom A keyboard entry using normal text entry is straightforward. Ho we ver , once an input mask is applied, the behavior of the k eyboard needs to change to accommodate the input mask's requireme nt.
Appendix A: Text Formatti ng 179 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom URL Resources A URL can be broken into se veral parts.
Appendix A: Text Formatting 180 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Appendix B - Wireless Technology 181 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix B - Wireless Technology Overview of Wireless Technology 802.11b/2.4 GHz and 802.11a/5 GHz are the two major WLAN standards and both operate using radio frequency (RF) technology .
Appendix B - Wireless Technology 182 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Although the calculations required to encrypt data with WEP can impact the performance of your wireless network, it's generally seen only when running benchmarks, and not large enough to be noticeable in the course of normal network usage.
Appendix B - Wireless Technology 183 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom TKIP Short for T emporal Ke y Integration, is pa rt of the IEEE 802.
Appendix B - Wireless Technology 184 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom WP A2 Also know as IEEE 802.11i, is an am endment to the 802.11 standard speci fying security mechanisms for wireless networks. The 802.
Appendix B - Wireless Technology 185 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP Authentication EAP (Extensible Authentication Proto col) is an Enterprise authentication protocol that can be used in both a wired and wireless network environment.
Appendix B - Wireless Technology 186 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom EAP communication overview EAP Authentication goes a step beyond just encrypting data transfers, b ut also requires that a set of credentials be validated before the client (panel) is allo wed to connect to the rest of the network ( FIG.
Appendix B - Wireless Technology 187 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom AMX Certificate Upload Utility The Certif icate Upload utility gi ves you the ability to compile.
Appendix B - Wireless Technology 188 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Step 2: Confirm t he Installation of the USB Driver on the PC The first time each AMX touch panel is connected to the PC it is detected as a new hardware de vice and the USBLAN driv er becomes associated with it (pan el specific).
Appendix B - Wireless Technology 189 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 11. Launch the Certificate Upload Utility and confirm the utility has detected the new USB connection to the panel: Click on the Local Address f ie ld's drop-do wn arrow .
Appendix B - Wireless Technology 190 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 12. Select the target de vices which be uploaded with the selected certificate. These can either be: indi vidually selected by toggling the box next to the Send entry (with the T ype column).
Appendix C: Troubleshooting 191 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Appendix C: Troubleshooting This section describes the solutions to possible ha rdware/f irmware issues that could arise during the common operation of a Modero touch panel.
Appendix C: Troubleshooting 192 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom If there is a yello w exclamation point ne xt to the AMX USB LAN LINK de vice (within the hardware devices section of the Unplug or Eject Hardware window), stop and close the USB operation.
Appendix C: Troubleshooting 193 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom USB Driver Symptom: My USB driver has a yellow e xclamation point and doesn’t appear to be working . The USB driv er was incorrectly installed and should be re-installed: 1.
Appendix C: Troubleshooting 194 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom 6. Plug-in the mini-USB cable into the corresp onding port on the panel. 7. W ait a few seconds and refresh the system. This re-establishes communication with the V irtual Master .
Appendix C: Troubleshooting 195 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Modero Panel Isn’ t Appearing in The On line Tree Tab 1. V erify that the System number is the same on both the NetLinx Project Navigator windo w and the System Settings page on the Modero panel.
Appendix C: Troubleshooting 196 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom The pinging is to determine if the Master is av ailabl e and to reply with a connection failure instantly if it is not. W ithout using the ping feature, you will still attempt to make a connection, but a failure will take longer to be recognized.
Appendix C: Troubleshooting 197 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom Panel Fails to Charge in MVP-WDS Should the panel fail, either the unit has no display or fails to boot passed the AMX logo, or does not charge in the MVP-WDS follo w these steps: 1.
Appendix C: Troubleshooting 198 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Intercom.
Appendix C: Troubleshooting 199 MVP-8400i 8.4" Modero® ViewPoint® Touch Panel with Int ercom.
4/11 © 2011 AMX. All rights reserved. AMX and the AM X logo are register ed trademarks of AMX. AMX reserves the right to alter specifica tions without notice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.
Ein wichtiger Punkt beim Kauf des Geräts AMX Modero MVP-8400i (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AMX Modero MVP-8400i noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AMX Modero MVP-8400i - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AMX Modero MVP-8400i reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AMX Modero MVP-8400i erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AMX Modero MVP-8400i besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AMX Modero MVP-8400i verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AMX Modero MVP-8400i. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AMX Modero MVP-8400i gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
