Benutzeranleitung / Produktwartung PC 365 des Produzenten IBM
Zur Seite of 150
Using Your Personal Computer PC 365 with Pentium Pro Processor.
.
Using Your Personal Computer PC 365 with Pentium Pro Processor IBM.
Note Before using this information and the product it supports, be sure to read the general information under Appendix B, “Product Warranties, License Information, and Notices” on page 111.
Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Laser Compliance Statement ............................... viii Lithium Battery Notice ................................... i x About This Book ....
Chapter 3. Operating Your Personal Computer ................... 1 9 Using Controls and Status Indicators .......................... 1 9 Starting Your Personal Computer ............................ 2 0 Using a Mouse ....................................
Cleaning Your Computer ................................. 5 7 Computer and Keyboard ................................ 5 7 Monitor Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Mouse . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 U.S. Government Users Restricted Rights ....................... 116 Other Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information Turn everything OFF. Attach signal cables to receptacles. First, remove power cord from outlet. To Disconnect Turn device ON. DANGER: Turn everything OFF. To Connect Remove signal cables from receptacles. Remove all cables from devices.
Laser Compliance Statement Some IBM Personal Computer models are equipped from the factory with a CD-ROM drive. CD-ROM drives are also sold separately as options.
Lithium Battery Notice CAUTION: Danger of explosion if battery is incorrectly replaced. When replacing the battery, use only IBM Part Number 33F8354 or an equivalent type battery recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
x Using Your Personal Computer.
About This Book This book will help you become familiar with your IBM Personal Computer and its many features. It describes how to configure, operate, and maintain your PC. In the unlikely event you experience problems, you will also find helpful troubleshooting information, as well as instructions for obtaining service in this book.
Related Publications The following publications, together with this book, contain information about your computer. Setting Up Your Personal Computer This publication contains instructions to help you set up your computer.
Technical Information Manual This separately purchased publication contains information for individuals who want to know more about the technical aspects of their computer.
xiv Using Your Personal Computer.
Chapter 1. Your IBM Personal Computer Thank you for selecting an IBM Personal Computer. Your PC incorporates many of the latest advances in personal computer technology and is easy to expand and upgrade as your needs change.
What Your IBM Personal Computer Offers This section describes many of the features of your computer. Support for Pentium Pro Microprocessors At the core of your PC is an Intel Pentium Pro microprocessor.
High-Capacity Hard Disk Drives Some PC models have a hard disk drive with an EIDE (enhanced integrated drive electronics) bus master interface to transmit data to and from the hard disk drive.
PD/CD-ROM Drive A PD/CD-ROM drive is preinstalled in some PC models. This dual-function IDE drive can be used as a standard CD-ROM reader or as a mechanism for day-to-day backup and storage of data. Using removable, rewritable optical disks called PD cartridges , you can save, store, and read files just as you would with a hard disk drive.
where USB devices can be attached. Note that your computer does not support a keyboard or mouse attached to the USB port. Watch the USB web site at www.teleport.com/ ˜ USB for further developments. Infrared Port With infrared technology, wireless communication is possible between infrared-enabled devices.
increases productivity because users are not interrupted during normal working hours and LAN traffic is kept to a minimum. IBM-Preinstalled Software IBM-preinstalled software is provided with some PC models.
Advanced Power Management Energy conservation is an important concern. Your computer has Advanced Power Management (APM) features that allow you to set different levels of energy conservation for specific components of your computer. You can view and change APM settings using the Configuration/Setup Utility program.
5.25-Inch Bay for Optional Drive 5.25-Inch CD-ROM or PD/CD-ROM Drive (Standard in Some Models) 3.5-Inch Diskette Drive 3.5-Inch EIDE Hard Disk Drive 3.
In PC models with a preinstalled SCSI hard disk drive, occupied and unoccupied drive bays are as follows: 3.5-Inch SCSI Hard Disk Drive 5.25-Inch CD-ROM or PD/CD-ROM Drive (Standard in Some Models) 3.5-Inch Diskette Drive 3.5-Inch Internal Bay for Optional Drive 3.
External Connectors The location of the external connectors for I/O devices varies by PC model. The following illustrations show the location of the external I/O connectors. Monitor Keyboard Mouse Serial USB Parallel Infrared Note: The model shown has an S3 Trio64V+ graphics adapter.
Monitor Keyboard Mouse Serial SCSI USB Parallel Infrared Video Feature Note: The model shown has a Matrox MGA Millennium graphics adapter and an Adaptec SCSI adapter installed. The SCSI adapter has one external 16-bit connector to which you can attach SCSI devices.
Features at a Glance The following information covers a variety of PC 365 models. Some of the features listed apply to specific models only. For a listing of features for your specific PC 365 model, refer to the System Summary screen in the Configuration/Setup Utility program.
PD/CD-ROM Drive One IDE, dual-function, rewritable PD/CD-ROM drive (standard in some models) Input/Output Features One 25-pin, ECP/EPP parallel port One 9-pin, 16550 UART serial port O.
Security Power-on and administrator passwords Lockable cover Startup sequence control Startup without diskette drive, keyboard, or mouse Unattended start mode Diskette and hard.
IBM-Preinstalled Software Preinstalled in some PC models are an operating system, device drivers to support built-in features, and other support programs. See About Your Software for a detailed description of the preinstallation package. System Specifications Size Depth: 455 mm (17.
Electrical Input Sine-wave input (50 to 60 Hz) is required Input voltage: – Low range: - Minimum: 90 V ac - Maximum: 137 V ac - Voltage switch setting: 115 or 115 V – High range: - Minimum.
Chapter 2. Arranging Your Workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace.
Glare and Lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources. Place the monitor at right angles to windows and other light sources, when possible. Reduce overhead lighting, if necessary, by turning off lights or using lower wattage bulbs.
Chapter 3. Operating Your Personal Computer This chapter provides information to help you in the day-to-day use of your computer. Information about the Configuration/Setup Utility program is also included in this chapter.
Starting Your Personal Computer 1. Turn on all external devices, and then turn on your computer. Numbers showing the amount of memory being tested appear in the top-left corner of the screen until the total amount of memory in the system is reached. Your computer is running the power-on self-test (POST).
Place the mouse beside the keyboard on a flat surface or mouse pad . (A mouse pad is a flat, smooth, foam-rubber pad available at most computer stores.) The mouse has a ball on the bottom, so working on a flat, smooth surface is important. You can use your right or left hand to control the mouse.
Configuring Your Computer The Configuration/Setup Utility program enables you to view and change the configuration and setup of your computer. The program is stored in the EEPROM (electrically erasable programmable read-only memory) of your PC.
Important In most cases, when you add or remove hardware from your computer, the BIOS (basic input/output system) detects the changes and then updates the configuration automatically.
If you have set both an administrator and a power-on password, you can type either of the passwords at the password prompt. However, if you think you might need to change any settings in the Configuration/Setup Utility program, you must type your administrator password at the password prompt.
When working with the Configuration/Setup Utility program menu, you must use the keyboard. Refer to the following table for the keys used to accomplish various tasks. Note: Active keys are displayed at the bottom of each screen; not all of the above keys are active with every menu.
2. Before you exit from the Configuration/Setup Utility program menu, select Save Settings if you want to save all settings as they currently appear. If you do not complete this step, your settings will not be saved. 3. From the Configuration/Setup Utility program menu, press Esc , and follow the instructions on the screen.
Viewing the System Summary You can use the Configuration/Setup Utility program to view a summary of the options and features in your computer. To view the system summary: 1. Start the Configuration/Setup Utility program (see “Starting the Configuration/Setup Utility Program” on page 23).
2. Select Date and Time from the Configuration/Setup Utility program menu. 3. Type the date and time in the appropriate fields. 4. Press Esc to return to the Configuration/Setup Utility program menu. 5. Before you exit from the program, select Save Settings from the Configuration/Setup Utility program menu and press Enter .
Off In password prompt Off mode (also referred to as Unattended Start mode), you are not prompted to enter your power-on password when you turn on the computer. The computer will run the CONFIG.SYS and AUTOEXEC.BAT instructions and start the operating system.
Password prompt Off mode is useful for network servers and other computers that operate unattended. If a power failure occurs, the computer will automatically restart and resume operating in this mode when power is restored, without operator intervention.
1. Start the Configuration/Setup Utility program (see “Starting the Configuration/Setup Utility Program” on page 23). 2. Select System Security from the Configuration/Setup Utility program menu. 3. Select Power-On Password . 4. Type your password and press Down Arrow ( ↓ ).
Administrator Password Setting an administrator password deters unauthorized persons from changing settings in the Configuration/Setup Utility program.
3. Select Administrator Password . 4. Type your password and press Down Arrow ( ↓ ). 5. Type your password again. 6. At Power-On Password Changeable by User , select Yes or No . Press Left Arrow ( ← ) or Right Arrow ( → ) to toggle between selections.
password jumper) on the system board. See Installing Options in Your Personal Computer for instructions on removing the computer cover and moving jumpers. Refer to the system board label inside the computer cover for the location of the CMOS Clear (password) jumper.
Display: With this option, you can disable the monitor entirely, or select one of the following reduced-power states: – Standby: In this mode, the screen is blanked, but the screen image is restored immediately when any activity is detected. – Suspend: In this mode, the monitor uses less power than in Standby mode.
Automatic Power-On Features The Automatic Power-On features within the Advanced Power Management menu allow you to enable and disable features that turn your computer on automatically.
Changing Keyboard Speed You can change the speed at which the keyboard responds when you hold down a key. The normal typematic rate is 10 characters per second, but you can use the Configuration/Setup Utility program to increase this rate to up to 30 characters per second.
Changing Monitor Settings Your computer has an S3 Trio64V+ or a Matrox MGA Millennium SVGA (super video graphics array) controller. SVGA is a video standard for displaying text and graphic images on a monitor screen. Like other video standards, SVGA supports a variety of video modes .
Updating System Programs System programs are the basic layer of software built into every IBM PC. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Configuration/Setup Utility program. POST is a set of tests and procedures that is performed every time you turn on your PC.
Diskettes You can use 3.5-inch diskettes in the diskette drive of your computer. If you want to use 5.25-inch diskettes, you must install a 5.25-inch diskette drive. (Refer to Installing Options in Your Personal Computer for instructions on installing optional diskette drives.
Handling and Storing Diskettes Inside the protective diskette case is a flexible disk with a magnetic-sensitive coating. This disk can be damaged by heat, dust, a magnetic field, or even a fingerprint. Use the following guidelines when handling and storing diskettes.
Labeling Diskettes Before using a diskette, label it so that you can identify the data stored on it. Labels usually come in the package with the diskettes. Diskette labels can become a problem if you do not apply them correctly. Loose edges or an excessive buildup of labels can prevent the diskette from being inserted or ejected.
Write Protecting Diskettes It is possible to accidentally format a diskette or unintentionally write data to it. Important information can be written over or lost. For this reason, it is a good idea to write protect important diskettes. You can read data from a write-protected diskette, but you cannot erase or change the data.
The operating system FORMAT command specifies how to format a specific type of diskette. Attention: Always format diskettes to their correct capacity. Failing to do so might cause unreliable results. Differences such as magnetic coatings, the thickness of the diskette material, and the recording technique used all affect the formatting operation.
Using a CD-ROM Drive Some PC models have a preinstalled CD-ROM drive. CD-ROM (compact disc read-only memory) technology offers quick access to enormous amounts of information. A compact disc can store more than 650 MB of data, such as the large files needed for audio, still and full-motion video, and still and animated graphics.
Do not place or store the CD in direct sunlight. Do not use benzene, thinners, or other cleaners to clean the CD. Do not drop or bend the CD. Loading a CD To load a CD into the CD-ROM drive: 1. Press the Eject/Load button. The tray slides out of the drive.
5. Close the tray by pressing the Eject/Load button, or by gently pushing the tray forward. Note: If the tray does not slide out of the drive when you press the Eject/Load button, insert the pointed end of a large paper clip into the emergency eject hole located above and to the left of the CD-ROM indicator light.
Do not insert anything other than a CD or a PD cartridge into the drive. Before moving the computer, remove the CD or the PD cartridge from the drive. The following is an illustration of the front bezel of the PD/CD-ROM drive preinstalled in some PC models.
Loading and Ejecting PD/CD Drive Media The following sections provide instructions for loading and ejecting a CD and a PD cartridge from the PD/CD-ROM drive. Read these instructions carefully to prevent damage to your PD/CD-ROM drive and media. Loading and Ejecting a CD: To load a CD into the PD/CD-ROM drive, complete the following steps.
the other hand, rotate the clip (located on top of the spring mechanism) in a counterclockwise direction as far as it will go. c. Place the CD in the tray with the label facing up. To do this, place the CD under clip 1 and push the spring mechanism into the computer.
the center hole of the CD and placing another finger on the outer edge of the CD) and push the spring mechanism back into the computer until clips 2 and 3 are cleared, as shown in the following illustration. Then carefully lift out the CD and close the tray.
A PD cartridge can be loaded in the same manner described in steps 1 and 2 with the clips in the extended position.) The following is an illustration of a properly loaded PD cartridge in a vertically placed computer.
4. Close the tray by pressing the Eject/Load button, or by gently pushing the tray in. When the tray is closed, the PD/CD indicator light on the front of the drive will activate to indicate what type of media you have inserted. The light will be amber if you have inserted a PD cartridge.
Instructions for formatting an unformatted PD cartridge and for formatting a previously formatted PD cartridge to FDISK-FAT format are provided for each operating system in the README2.TXT file on the Ready-to-Configure CD that comes with your computer.
Using Locks To deter unauthorized use of your computer, you can lock the cover, sliding door, and keyboard. Locking the Cover and Sliding Door You can use the cover lock and keys to secure the outside cover and the sliding door on the front panel. You can lock both the sliding door and the computer cover, the cover only, or neither.
56 Using Your Personal Computer.
Chapter 4. Taking Care of Your Computer This chapter provides guidelines for the proper handling and care of your computer. Basics Here are some basic points about keeping your computer functioning properly: Keep your computer in a clean, dry environment.
To clean the screen surface, wipe it gently with a soft, dry cloth, or blow on the screen to remove grit and other loose particles. Then use a soft cloth moistened with a nonabrasive liquid glass cleaner. Mouse If the pointer on the screen does not move smoothly with the mouse, you might need to clean the mouse.
The battery requires no charging or maintenance throughout its life; however, no battery lasts forever. If the battery fails, the date, time, and configuration information (including passwords) are lost. An error message is displayed when you turn on the computer.
60 Using Your Personal Computer.
Chapter 5. Solving Problems This chapter presents an overview of diagnostic tools available to you. You can use these tools to identify and correct problems that might come up as you use your computer. This chapter also contains information about option diskettes and terminate-and-stay-resident (TSR) programs.
Note If your computer does not start when you press the power switch, do the following: Make sure all cables are securely connected to the correct locations. Check to see if the voltage-selection switch is set to the correct position. Make sure the computer cover is installed properly (pushed all the way on).
“Solving POST Error Message Problems” on page 64 and “POST Message Charts” on page 67. If you hear no beep at all during POST, refer to “Troubleshooting Charts” on page 86. You might need to have your computer serviced. Error Messages Error messages that appear on the screen might be text, numeric, or both.
Solving POST Error Message Problems: If you receive an error message during the power-on-self-test (POST), completing the steps outlined in this section might enable you to resolve the problem.
that are malfunctioning or that have been changed since the last time you turned on your computer. If you did not knowingly make a change to a flagged menu item, there is likely a malfunction in that item. If you made a change, continue here. If you did not make a change, go to step 5e.
6. For more information about what caused an error message to appear and what action to take, refer to the following chart. If you are unable to resolve a problem and need assistance, refer to Chapter 6, “Getting Help, Service, and Information” on page 99.
POST Message Charts The computer might display more than one error message. Often, the first error to occur causes subsequent errors. When using the POST message charts in this section, always begin by following the suggested action for the first error message that appears on your computer screen.
POST Message Description 161 The battery on the system board is dead. CAUTION: Danger of explosion if lithium battery is incorrectly replaced. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of batteries as required by local ordinances or regulations.
POST Message Description 162 A change in device configuration occurred. This message is displayed under one or more of the following conditions: A new device has been installed. A device has been moved to a different location or cable connection.
POST Message Description 163 The clock is not working correctly. Action: Set the correct date and time. If the date and time are set correctly and saved and the 163 error message reappears, replace the battery. If this does not correct the problem, have the computer serviced.
POST Message Description 20X A failure occurred during testing of the memory. This error can be caused by incorrectly installed memory, a failing DIMM, or a system-board failure.
POST Message Description 601 A failure occurred during testing of the diskette drive and diskette-drive controller. This error can be caused by a loose or incorrectly connected cable, a failing drive, or a failing system board. Note: The computer can be used, but one or more diskette drives might not work.
POST Message Description 662 A diskette drive configuration error occurred. Action: 1. Verify that the Configuration/Setup Utility program correctly reflects the number of diskette drives you have installed. (For instructions on using the Configuration/Setup Utility program, refer to “Configuring Your Computer” on page 22.
POST Message Description 1800 A PCI adapter has requested a hardware interrupt that is not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the hardware interrupt settings are not correct, change and save the settings.
POST Message Description 1801 A PCI adapter has requested memory resources that are not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the memory resource settings are not correct, change and save the settings.
POST Message Description 1802 A PCI adapter has requested an I/O address that is not available, or the PCI adapter might be defective. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the I/O address settings are not correct, change and save the settings.
POST Message Description 1803 A PCI adapter has requested a memory address that is not available, or the PCI adapter might be defective. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the memory address settings are not correct, change and save the settings.
POST Message Description 1804 A PCI adapter has requested a memory address that is not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the memory address settings are not correct, change and save the settings.
POST Message Description 1850 A Plug and Play adapter has requested a hardware interrupt that is not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the hardware interrupt settings are not correct, change and save the settings.
POST Message Description 1851 A Plug and Play adapter has requested memory resources that are not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the memory resource settings are not correct, change and save the settings.
POST Message Description 1852 A Plug and Play adapter has requested an I/O address that is not available, or the Plug and Play adapter might be defective. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program.
POST Message Description 1853 A Plug and Play adapter has requested a memory address that is not available, or the Plug and Play adapter might be defective. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program.
POST Message Description 1854 A Plug and Play adapter has requested a memory address that is not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the memory address settings are not correct, change and save the settings.
POST Message Description 1856 A Plug and Play adapter has requested a DMA address that is not available. Action: 1. Make sure that all ISA legacy adapters are set correctly in the Configuration/Setup Utility program. If the DMA address settings are not correct, change and save the settings.
POST Message Description 1962 A startup sequence error occurred. Action: 1. Make sure the startup options are set correctly in the Configuration/Setup Utility program. If the settings are not correct, change and save them. For instructions on using the Configuration/Setup Utility program, see “Configuring Your Computer” on page 22.
Troubleshooting Charts You can use the troubleshooting charts in this section to find solutions to problems that have definite symptoms. Important If you find it necessary to remove the computer cover, first read "Removing the Cover" in Installing Options in Your Personal Computer for important safety information and instructions.
Diskette Drive Problems Action Diskette drive in-use light stays on, or the system bypasses the diskette drive. If there is a diskette in the drive, verify that: 1. The diskette drive is enabled. Use the Configuration/Setup Utility program to check this.
Monitor Problems Action Wavy, unreadable, rolling, distorted, or jittery screen images. If the monitor self-tests show that the monitor is working properly, verify that: 1.
Monitor Problems Action Screen flickers. Set the monitor for the highest, noninterlaced refresh rate supported by your monitor and the video controller in your computer.
Monitor Problems Action Blank screen. Verify that: 1. The computer power cord is plugged into the computer and a working electrical outlet. 2. The monitor is turned on and the Brightness and Contrast controls are adjusted correctly. 3. The monitor signal cable is securely connected to the monitor and the monitor connector on the graphics adapter.
Intermittent Problems Action A problem occurs only occasionally and is difficult to detect. Verify that: 1. All cables and cords are securely connected to the rear of the computer and attached devices. 2. When the computer is turned on, the fan grill is not blocked (there is air flow around the grill), and the fans are working.
Memory Problems Action The amount of memory displayed is less than the amount of memory installed. The amount of available memory shown might be somewhat less than expected because of basic input/output system (BIOS) shadowing in random access memory (RAM).
Option Problems Action An IBM option that was just installed does not work. Verify that: 1. The option is designed for your computer. 2. You followed the installation instructions supplied with the option and in Installing Options in Your Personal Computer .
Parallel Port Problems Action Parallel port cannot be accessed. Verify that: 1. Each port is assigned a unique address. 2. The parallel-port adapter, if you added one, is properly installed and firmly seated. Refer to Installing Options in Your Personal Computer for instructions on adding adapters.
Software Problem Action Is your software program OK? To determine if problems are caused by installed software, verify that: 1. Your computer has the minimum memory requirements needed to use the software. Refer to the information supplied with the software to verify memory requirements.
Diagnostic Programs IBM provides programs that you can run to diagnose hardware and some software problems. A description of these programs follows. QAPlus/PRO: You can use QAPlus/PRO to diagnose hardware problems. QAPlus/PRO also includes several utility programs that provide helpful information about your computer.
CoSession: CoSession is a remote-control diagnostic program that can be used by another individual, such as an IBM HelpWare technician or your in-house administrator, to help diagnose problems with your computer from a remote location. CoSession is provided on the Ready-to-Configure CD that comes with your computer.
98 Using Your Personal Computer.
Chapter 6. Getting Help, Service, and Information If you need help, service, technical assistance, or just want more information about IBM products, you will find a wide variety of sources available from IBM to assist you. This section provides information about those sources.
Technical information is available on a wide range of topics, such as: Hardware setup and configuration Preinstalled software OS/2, DOS, and Windows Networking Communications Multimedia In addition, the latest device driver updates are available.
You can call the IBM PC Company Automated Fax System 24 hours a day, 7 days a week. Follow the recorded instructions, and the requested information will be sent to your fax machine. To access the IBM PC Company Automated Fax System, do the following: In the U.
Please have the following information ready when you call: Serial numbers of your computer, monitor, and other components, or your proof of purchase Description of the problem Exact wording of any error messages Hardware and software configuration information for your system If possible, be at your computer when you call.
Enhanced PC Support Line Enhanced PC Support is available for desktop and mobile IBM computers that are not connected to a network. Technical support is provided for IBM computers and IBM or non-IBM options, operating systems, and application programs on the Supported Products list.
Using IBM and non-IBM network operating systems Interpreting documentation You can purchase this service on a per-call basis, as a multiple-incident package, or as an annual contract with a 10-incident limit. For more information about purchasing Network and Server Support, see “Ordering Support Line Services.
On-site service to premium on-site service If your warranty provides for on-site service, you can upgrade to premium on-site service (4-hour average on-site response, 24 hours a day, 7 days a week).
106 Using Your Personal Computer.
Appendix A. Computer Records This appendix contains forms for recording information about your computer, which can be helpful if you decide to install additional hardware, or if you ever need to have your computer serviced. Serial Numbers and Keys Record and retain the following information.
the page and store it in a secure place, or store this manual in a secure place when you are not using it. 108 Using Your Personal Computer.
Device Records Use the following tables to keep a record of the options in or attached to your computer. This information can be helpful when you install additional options, or if you ever need to have your computer serviced.
Location Option Description Infrared Connector 3.5-Inch Bay 1 1.44 MB diskette drive 5.25-Inch Bay 2 Ø IDE CD-ROM drive Ø IDE PD/CD-ROM drive Ø Other: 5.25-Inch Bay 3 Ø SCSI hard disk drive Ø Other: 3.5-Inch Bay 4 Ø EIDE hard disk drive Ø Other: 3.
Appendix B. Product Warranties, License Information, and Notices Hardware Limited Warranty The following is the statement of limited warranty for the United States, Canada, and Puerto Rico.
If you transfer a Machine to another user, warranty service is available to that user for the remainder of the warranty period. You should give your proof of purchase and this Statement to that user. However, for Machines which have a life-time warranty, this warranty is not transferable.
claim damages from IBM (including fundamental breach, negligence, misrepresentation, or other contract or tort claim), IBM is liable only for: 1. damages for bodily injury (including death) and damage to real property and tangible personal property; and 2.
114 Using Your Personal Computer.
Appendix C. License Information The license information in this booklet is for IBM and non-IBM logo programs covered by the IBM International Program License Agreement. Some programs referred to in this booklet might not be available in all languages or in all countries.
Warranty System Programs – No. PROGRAMS DESIGNATED AS "NO" ARE PROVIDED WITHOUT A PROGRAM WARRANTY. THEY ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND.
YOU MUST REPRODUCE THE COPYRIGHT NOTICE AND ANY OTHER LEGEND OF OWNERSHIP ON EACH COPY, OR PARTIAL COPY, OF A PROGRAM YOU CREATE ON DISKETTE OR OTHER PORTABLE MEDIUM.
Notices References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used.
Microsoft, Windows, and Windows NT are trademarks or registered trademarks of Microsoft Corporation. Other company, product, and service names may be trademarks or service marks of others. PRODIGY Prodigy Services Company QAPlus DiagSoft, Inc. QAPlus/PRO Diagsoft, Inc.
Electronic Emission Notices Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Telecommunication Notices Federal Communications Commission (FCC) and Telephone Company Requirements 1. This device complies with Part 68 of the FCC rules. A label is affixed to the device that contains, among other things, the FCC registration number, USOC, and Ringer Equivalency Number (REN) for this equipment.
Canadian Department of Communications Certification Label NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements.
AVIS : L'INDICE DE CHARGE (IC) assigné à chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut être raccordé à un circuit téléphonique bouclé utilisé par ce dispositif.
Power Cord Notice For your safety, IBM provides a power cord with a grounded attachment plug to use with this IBM product. To avoid electrical shock, always use the power cord and plug with a properly grounded outlet.
IBM power cords for a specific country are usually available only in that country: IBM Power Cord Part Number Used in These Countries 13F9940 Argentina, Australia, China (PRC), New Zealand, Papua New .
126 Using Your Personal Computer.
Index Numerics 1-800 telephone assistance 101 900 number support 103 A adapters 2, 6 adjusting chair 17 administrator password computer startup 20, 30 Configuration/Setup Utility program 30 deleting 3.
D damage, preventing 57, 59 date, setting 27 DDC (display data channel) 38 device configuration error 69 device drivers, video 37 diagnostic charts 86 programs 6, 96 tools 61 DIMMs 12 diskette drives .
graphics adapter 5 H hard disk drives adding 7 backing up 59 indicator light 19 location 7 maximum 3 power management 35 supported 3, 12 hardware power management 34 heat output 15 help 99 HelpWare 10.
mouse cleaning 58 locked 28 password prompt off mode 29 port 20, 29 problems 91 serial port 20, 29 unattended start mode 29 using 20 moving computer 59 N network server startup support 101 server supp.
power-on self-test See POST printer problems 94 privileged-access password See administrator password problems solving 61 startup 20 processor See microprocessor PRODIGY 100 publications, ordering 105.
turning off computer 21 on computer 20 typematic rate 37 U unattended start mode 29 universal serial bus port 4, 13 V venting of hot air 18 VGA (video graphics array) 38 video 5 controller 13, 38 devi.
.
IBM Part Number: 84H8308 Printed in U.S.A. October 1996 84H83ð8.
Ein wichtiger Punkt beim Kauf des Geräts IBM PC 365 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie IBM PC 365 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für IBM PC 365 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von IBM PC 365 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über IBM PC 365 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon IBM PC 365 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von IBM PC 365 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit IBM PC 365. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei IBM PC 365 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
