Benutzeranleitung / Produktwartung MX9 des Produzenten Honeywell
Zur Seite of 356
MX9 Mobile Computer with Microsoft® Windows® Mobile 6.5 User’s Guide.
Disclaimer Honeywell Interna tional Inc. (“HII”) reser ves the right to make changes in sp ecifications and ot her informatio n contained in th is document without pr ior noti ce, and the reader should in all case s consult HII to deter mine whether any such chang es hav e been made.
1 Chapter 1 - MX9 Agency Compliance Laser Warnin gs ................ ............. ................ ............. ................ ............. ............. ............. ... .............. 1- 1 Laser Labe l Location .............. ............. ...
2 Using a Control Panel ............................ ............. ............. ................ ............. ................ ....... ...... 2-1 2 Body Worn Accessor ies .................. ................ ............. ................ ...........
3 Integrated Ba r Code Deco ders ........................ ................ ............. ................ ............. ................ . .3- 6 Tethered Bar Cod e Decoders ... ............. ............. ................ ............. ............. .
4 Status Popup ...... ............. ................. ............ ............. ................. ............ ............. ............. ............ 5-6 HSMConnect .......... ............. ................ ............. ................ ..........
5 Battery Power ............... ............. ............ ................. ............. ................ ............. ............ ... ....5-33 External Powe r ...................... ............. ................ ............. ................ ..
6 Calendar ...... ................. ............. ............ ................. ............. ................ ............. ............ ....... 5-70 Address Book ........ ............. ................ ............. ............. ................ .
7 Manual (La unch) ........... ............. ................ ............. ............. ................ ............. ................ ..... 6-8 Match ..................... ................ ............. ................ ............. .............
8 Symbology Se ttings ............................ ............. ................ ............. ................ ............. .......... ... ...8 -10 Processing Or der ......... ............. ................ ............. ............. .............
9 Chapter 10 - Enabler Inst allation and Configuration Introduction ...................... ............. ................ ............. ................ ............. ............. ......... .... ............. ... 10-1 Installation ....... ...........
10 Global Tab .......... ............. ................. ............ ............. ................. ............ ................. ...... ...... ..... 11-14 Custom Para meter Option ............ ................ ............. ................ ......
11 Charger Clean ing, Storage and S ervice . ................ ............. ............. ................ ............. ............ ...... .13 -7 Cleaning ....... ............. ............. ................ ............. ................ ..........
12 Vehicle Cradle RAM Ball Assembly ................. ................ ............. ................ ................ ..... 14-14 RAM Circular Base Footprint ................. ............. ................. ............ ................. ...........
1 - 1 1 MX9 Agency Compliance MX9 mobile computers meet or exceed the requirements of all applicable standards organizations for saf e operation. Howe ver , as with any electrical equipment, the best wa y to ensure safe ope ration is to operate them according to the agency guidelines that f ollow .
1 - 2 1. This device may not cause harmfu l interference. 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits f or a Class B digital de vice pursuant to par t 15 of the FCC Rules.
1 - 3 CE Mark The CE mar king indicates comp liance with the following directives: • 1995/5/EC R&TTE • 2011/65/EU RoHS (Recast) In addition, complies to 2006/95 /EC Low V oltage Directiv e, w hen shipped with reco mmended power supply . European contact:: Honeywell shall not be liable f or use of our product with equipme nt (i.
1 - 4 Dealer License - Repu blic of Singapore V ehic le P ower Supply Connection Saf ety Statement V ehicle P ower Supply Connection: If the supply connection is made directly to the batter y , a 10A slow-b low fuse should be installed in the positive lead within 5 inches (12.
2 - 1 2 Getting Star ted Overview The MX9 is a ruggedized handheld computer targeted for indoor and outdoor use. It is powered by a lightweight main battery that can be remov ed and replaced wit hout the need for special tools. MX9 wireless connectivity is secured by user-configured encr yp tion and authenti cation protocols.
2 - 2 • Place the MX9 in a powered desktop or vehicle mounted cradle. 3. Press the Power key. Software Setup Hardware setup should be complet ed bef ore star tin g software setup. 1. Calibrate touch d isplay. 2. Set Date and Time Zone. 3. Set Power Timers.
2 - 3 Components Fr ont View 1. Microphone 2. Touch screen 3. Speaker 4. Scan buttons 5. Enter key 6. Scanner status LED 7. Power key The abov e list is the same on the 38 key MX9.
2 - 4 62 Ke y Ke ypad 1. Function Keys 2. Backspace [BS] key and Space [SPC] key 3. Escape [ESC] key 4. Power key 5. Tab key 6. Alt key 7. Control [CTL] key 8.
2 - 5 38 Ke y Ke ypad To p Bottom 1. Diamond 1 key 2. Function keys 3. Tab | Space | Backspace keys 4. Diamond 2 key 5. Orange key 6. Escape [ESC] key 7.
2 - 6 Back - Battery Ba y T rigger Handle 1. Battery Charging Terminals 2. Battery Bay 3. Battery Bay Access Tab 1. Trigger 2. Tether attach point Stylus storage ba y in trigger han dle base.
2 - 7 Hand Strap Locking and Unloc king the MX9 Note: Review the Unlock process before locking the MX9. Locking the MX9 The MX9 can be l ock ed manually by tapping Start > Lock. By def ault, this option is include d on the Star t screen at the bottom of the screen.
2 - 8 1. Detach the bottom hook of the hand strap (if installed). 2. Tilt the end (with the terminal s) of the fully charged battery pack into t he upper end of the battery compartment, and firmly press the other end until it is full y inserted into the battery compartment.
2 - 9 The main batter y can be recharged while it is in the MX9: • by connecting the MX9 AC power adapter to the I/O connector at the base of the MX9. • by docking the MX9 in a powered desk cradle • by docking the MX9 in a powered vehicle cradle • or by connecting the car power adapter (CLA) to the I/O connecto r at the base of the MX9.
2 - 10 Options are: Off, Shor t, Medium or L ong. Vibration can also be adjusted by tapping the speaker icon in the top right corner of the Start screen. A Volume window opens. Tap the Vibrate radio button to toggle vibration on and off. Vibration duration can be set using the Data Col lection control panels.
2 - 11 Remov e the protective film from its contai ner . Remov e any protective bac king from the film sheet by lifting the backing from a corner of the film. Dis card the bac king. Apply the film to the touch screen star ting at one side and smoothing it across the display .
2 - 12 Setting Speaker V olume The speaker is located on the front of the MX9 between the Scan ke ys and under neath the LEDs. Speaker v olume can be adjusted to a comfor table le vel f or the listener by using the k eypad or by changing parameters in a control panel.
2 - 13 Body W orn Accessories Protect the T ouch Screen whe n using a Holster / Carr ycase . Holster without Handle The MX9 is inser ted upside-d own in the holster with the t ouch screen f acing the bel t connecting the holster to the body .
2 - 14 Using the Input P anel / Vir tual Ke yboar d The input panel/vir tu al ke yboard is alwa ys av ailable when needed e.g., te xt entry . Place the cursor in the text en try fiel d and, usin g the stylus: • Tap the Shift key to type one capital letter.
2 - 15 When the Bluetooth LED on the MX9 is on: • the MX9 is paired with another Bl uetooth device but is out of range or not connected, or • is paired and conn ected to another Bluetooth device, or • is discovering othe r Bluetooth devices. • The LED blinks slowly (Bluetooth LED is on for on e second, off for five seconds) when it is idle.
2 - 16 Using the T ouch Screen The figure shown above is an e xample and is shown only to aid in d escribing how the user can switch between applications using a stylus . When the user taps the Switchpad icon wit h the stylus, a menu pops up listing the application s av ailable to the user .
2 - 17 When the hatch is being closed, carefu lly mov e cables and wires back into the cavity before securing the hatch. Before securing the hatch completely , e xamine the seam between the front and back half of the MX9. If the gasket is off-center , loosen the screws a little, adjust the gasket and re-tighten the screws .
2 - 18 Attaching the Hand Strap Note: Either the trigger handle is attached to the MX9 or the han d strap is attached, no t both. In the absence of a trig ger hand le, the hand strap shou ld be used at all times. The hand strap is pre-installed on a MX9 that is purchased without a trigger handle.
2 - 19 Attaching the T rig ger Handle Pressing the tr igger on the trigger han dle activates the integrated scanner and functions the same as the Scan ke y on the ke ypad. With the handle installed the Scan key on the ke ypad remains active . The trigger dup licates the operation.
2 - 20 Adjusting the Headset / Micr o phone and Securing the Cable The headset consists of an ear piece, a microphone, a clothing clip and a cable. The headset atta ches to the audio cable end of the voice cab le which attaches to the MX9. Align the audio con nector and the headset qu ick connect cable end.
2 - 21 Connecting Cables to the MX9 Note: Do not connect or disco nnect cables in a Hazardous location. Connecting the USB Host and P ower Cab le A C/DC Adapter must be assembled before this process begins. Do not connect AC po wer to the AC Adapter until in structed in the following procedure: 1.
2 - 22 Connecting the Serial and P ower Cable A C/DC Adapter must be assembled before this procedure begins. Do not connect AC po wer to the A C Adapter until instr ucted to do so in the follo wing procedure: 1. Holding the cable I/O connector (1), sque eze the catch rel ease buttons in until the catches are open.
2 - 23 Replacing the CLA Fuse Equipment needed: 5 A fuse of the same size and amperage. 1. Remove the CLA from the cigarette lighter outlet on the vehicle . 2. Disconnect the cable from the MX9. 3. Unscrew the tip of the adapter end. 4. Replace the blown fuse with a fuse of the same rating and size.
2 - 24 Star tup Help Issue: Can’t change the date/time or adjust the volume . Soluti on: AppLock is installed and may be running i n User Mode on th e MX9. AppLock user mode restricts access to the control pan- els. Issue: T ouch screen is not accepting styl us ta ps or needs recal ibration.
3 - 1 3 Har d ware Configuration 802.11 b/g and a/b/g Wireless Client The MX9 has an 802.11x network card that supp or ts diversity with two internal antennas. The CPU board does not allow hot sw apping the network card. WEP , WP A and LEAP are suppor ted.
3 - 2 Input/Output Connector A single external connector at the base of th e MX9 provides the f ollowing signals: • USB Host and USB Client • RS232 with support for powering a tethered d evice (e.
3 - 3 Ke ypads The MX9 ke ypad is either a 62-ke y full alphanumer ic ke ypad or 38-key n umeric-al pha. The 62 key k eypad has an ANSI or a 5250 overla y . KeyMaps (page 12-1) are availab le for all ke ypads. Note: The keypad backlight default setting is to follow the display backlight setting until it is change d by the user.
3 - 4 P ower K ey Funct ions The P ower k ey is located at the bottom left of the keypad. The P ower On/Off ke y is a momentar y contact. Fu nction is as follo ws: Status LEDs Sev e ral LEDs are located on the front of the MX9 abov e the integrated speaker .
3 - 5 Scanner Status LED The integrated scanner , and imager, Scan Status LED is cent ered below the MX9 k eypad, ne xt to the P ower button. • Steady green indicates a good scan • Steady red indi.
3 - 6 Scanners and Ima gers Note: The maximum number of communicatio n ports from which the Data Collection We dge can simultaneously supp ort input is three.
4 - 1 4 P o wer Modes and Batteries Po w e r M o d e s The MX9 has three power modes: On, Suspend and Off . On Mode The Display When the display is On: • the keypad, touch screen and all peripherals.
4 - 2 The MX9 will only resume from a suspended state if an interr upt occurs and the CPU has been programmed to wake when an interrupt occurs. An interrupt from any listed device tr ansiti ons the OS back to the On state .
4 - 3 Batteries The MX9 is designed to work with a replaceable 2400 mAh Lithium-Ion (Li-Ion) batter y pack from Honeyw ell. Under nor mal conditions it should last app ro ximately eight hou rs before requiring a recharge.
4 - 4 Handling Batteries Safel y • Never dispose of a battery in a fire. This may cause an explosion. • Do not replace individual cells in a battery pack. • Do not attempt to pry open the battery pack shell. • Be careful when handling any ba ttery.
4 - 5 One end consists of a plug compatible with a standard vehicle cigarette lighter adapter (CLA). The Car P ow er Adapter has a standard size CLA plug that uses center positive (+12V) and sleev e ground. A re placeable fuse is provided on the input side.
4 - 6.
5 - 1 5 Software Configuration Intr oduction There are se veral diff eren t aspects to the setup and configuration of the MX9. Many of the setup and configuration setting s are dependent upon the optional features such as hardware and software installed on the m obile device .
5 - 2 The MX9 has a unique 128-bit ID code as re quired by the Window s Mobile specification. Thi s ID number is generated b y the boot loader . This ID code is av ailable in the About Inf o settings panel, and via a Win32 standard API.
5 - 3 The main screen for the MX9 is kno wn as the T oday screen. T he T oda y screen shows v arious options and status icons. The T oda y screen appea rance is configurable b y selecting Start > Settings > T oday . Both the appearance of the T oda y screen and the items display ed may be configured .
5 - 4 When the MX9 is lock ed, tapping on Unlock at the bottom of the screen unlocks the MX9. Depending on the settings, a pass word may be required. The MX9 can also be confi gured to lo c k after a period of inactivity . F or more inf or mation, see the Lock settings late r in this sect ion.
5 - 5 More information o n Bluetooth can be found in the Bluetooth settings later in this secti on. Soft Ke ys Soft K eys are displa yed at the bottom of the T oday screen. T he ke ys display ed vary by the active screen/application. The soft ke ys generally provide menus for the selected application.
5 - 6 Windows Media Start > Windows Media Codecs are included for WMA, WMV , MP3 and W A V fi les. Bluetooth (Option) Start > Settings > System > Bluetooth Only installed on a Bluetooth equipped MX9. The System Admi n istrator can Discove r and Pair targeted Bluetooth devices f or each MX9.
5 - 7 • Modify registry keys • Perform conditional operati ons Note: The Enhanced Launch utility does not intera ct with or affect the AppLock Lau nch command. F or a complete list of Launch functions i ncluding commands and command structure, see Enhan ced Launch Utility (p age 9- 1).
5 - 8 1. Summit radio card is located in the back hal f of the MX9 assembly. 2. SIMM card is located in the front ha lf of the MX9 assembly. 3. SD card is located in the front ha lf of the MX9 assembly. Pr ocedure While the hatch is open slide the in stalled SD card o ut of t he slot.
5 - 9 Use the up and down arrow k eys on the MX9 to quic kly scroll through the icons, or , using screen touch gestures, br ush the window up or down with a finger or the stylus. ActiveSync. Basic ActiveSync configuration, incl uding synchro nization with an Exchange serve r.
5 - 10 Office Mobile Task Manager. View and cancel running tasks. See Task Manager (page 5-56). Tasks. Task list appl ication. Can be synchronized with PC Ou tlook task list using ActiveSync. See Tasks (pa ge 5- 75) Today. Configure the appearance and th e item s to display on the Tod ay screen.
5 - 11 Settings P ersonal System About Info (page 5-13). View software, hardware, versions and network IP. No user intervention required. Clock & Alarms (page 5-15). Set Date, Time, Time Zone, and alarms. Lock (page 5-17). Set password protection.
5 - 12 Backlight (page 5-33). Set the display backli ght brightness and display/keyp ad backlight timeout. Configure the timeout based on type of power source: battery or external power. Bluetooth. Discover then pair with nearby discoverable Bluetooth devices.
5 - 13 Connections Settings P anels About Info The data cannot be edited by the MX9 user on these panels. V ersion window inf or mation is retri e ved from the registr y . V ersion T a b and the Registr y Modify the Registr y using the Registr y Editor .
5 - 14 V ersion strings can be equal to or less than 25 4 characters. Be cause the strings are disp lay e d in a text box, any n umber can be accommodated, up to the 64K byte te xt bo x limitatio n. Languages The Software tab ma y display the current language.
5 - 15 Cloc k & Alarms Time Adjust the settings and tap ok to sav e the changes. Select Y es on the popup b o x and the changes take effect immedi- ately .
5 - 16 1. Tap the check box to enabl e the alarm. If the check box has a che ck mark, the check mark is removed. If the check box is empty, a check mark is placed in the check box when tapped. 2. Tap < Description > and enter a description. The description is limited to 63 characters.
5 - 17 Lock P assw or d Set the lock / unloc k behavior f or the MX9. Prompt if phone unused for T ap the check bo x to enable (check ed) and set the inactivity time out before the MX9 loc ks.
5 - 18 Hint If the pass word entr y isn’t successful after a predefined number of attempts, the password hint is display ed. Display Unlock displa y defaults to Windo ws Classic.
5 - 19 Po w e r Repor ts the cu rrent batter y state and allows the user to set suspend timeouts. Battery Batter y power is displa yed f or both the main and inter nal Super-cap batteries.
5 - 20 Adv anced Select the inactivity timeout pe riod before the MX9 goes in to suspend. The settings o n this panel are for the suspend timers on ly .
5 - 21 Sounds & Notifications Set volume parameters and assign sound W A V file s to Windows Mobile ev e nts. Options that cannot be edited b y the user are dimmed. Sounds F ollow the instructio ns on the screen and tap ok to sav e the changes. Changes take effect immediatel y .
5 - 22 Notifications The Event bo x lists sev eral e vents that can hav e an asso ciated notifica tion. The notifi ca tion, depending on the event selected, ma y consist of play ing a sound, displaying a scr een message, flashing a light or tr iggeri ng the vi bration motor .
5 - 23 T oday Configure the appearance and the items to display on the T oda y screen. Use the Appearance pane l to assign a theme for the device. The def ault theme is Windows Mobile Cla ssic Bl u e. An y user installed themes are inclu ded in the list.
5 - 24 Pe r s o n a l Pa n e l s Buttons Pr ogram Buttons Program b uttons can be used to assi gn functions to cer tain keys such as F1 through F5 and the diamond ke ys. Buttons can only be assigned to programs that ha v e an icon in the Star t menu or the Se ttings folder (including sub-folders).
5 - 25 Up/Down Contr ol Mov e the sliders with the stylus to customize the delay bef o re repeating and the repeat rate for the up/down controls ..
5 - 26 Input Input Method Select the pref erred method of input. The default method of input is the k eyboar d or input panel . When the cursor is located in a field allowing te xt input, the input panel may automatically be displa y ed.
5 - 27 W ord Comp letion Setting Default Suggest words when entering te xt Enabled Suggest after enter ing A space Suggest _ word(s) 4 Add a space after word Enabled Enable auto correct Enabled.
5 - 28 Options Setting Default V oice recording format 8000 Hz, 8 Bit, Mono Def ault zoom lev el f or wr iting 200% Def ault z oom le vel f or typing 10 0% Capitalize first letter of sentence Enabled .
5 - 29 Owner Information Set the MX9 owner details. Enter the information and tap ok to sav e the changes. The changes take eff ect immediately . Note: Owner Identification name listed in Start > Settings > Personal > Owner > Informa tion is not used during Bluetooth operation.
5 - 30 System P anels About The About panels sh ow OS v ersions, allow de vice name and description in put and display cop yright information . The fol- lowing screens are e xamples only . Ve r s i o n This screen displays inf or mation on the in stalled operating system and the hardware.
5 - 31 Device ID The device name and description can be changed. Enter the name and description using either the keypad or the Input P anel and ta p ok to sav e the change s. The changes take effe ct immediatel y . Note: Changing the device name de letes previous ActiveSync settings including backed up user files.
5 - 32 Copyrights This screen is presented for inf or mation only . The Co pyrights information cannot be cha nged by the user ..
5 - 33 Backlight Set the power management timers for the displa y and keyboard bac klights. Set the display brightness for batter y and exter- nal power . IMPORT ANT – When the backlight timer e xpires, the display bac kl ight an d the display are OFF , as is the keypad bac klight.
5 - 34 External P ower When the MX9 is on external power and the backlight timer e xpires, the display and the bac klights for the displa y and ke ypad are tur ned off. Default v alue is 1 minute and both the check box es a re enabled. Adjust the settings and tap ok to sav e the changes.
5 - 35 Cer tificates Manage digital cer tificates used for secure communication. View – displa ys details of the cer tificate. P erso nal cer tificates may be e x tended from the view screen. Delete – remov es the cer t ificate from the device . Delete is not availab le if the cer ti ficate was installed by a de vice adminis- trator .
5 - 36 1. Copy the .pfx or .p12 file to a folder on th e MX9. 2. Use File Explorer to browse to the location of the file and op en the file by tapping the file name. 3. Type in the password to unlock the certificate and tap Done. 4. The new certificate is copied to the Personal certificate st ore on the MX9.
5 - 37 Root This panel lists any installed Root cer tifi cates. Root certi f icates are us ed to authenticate cer tificates re ceived from other hosts. T o install a Root cer tificate: 1. Copy a DER-encoded .cer file, a base64-e ncoded .cer file or a .
5 - 38 Encryption This panel enables or disables encr yption of data files o n removab le storage cards. The def ault is Disabled. There may be a delay while files on remov able storage cards are encr ypted.
5 - 39 External GPS This panel confi gures serial GPS access over hardw are ser i al por ts using the Microsoft GPS manager . The por t used , baud rate and por t shar ing must be specified.
5 - 40 Har dware Access.
5 - 41 License Manager Use this option to view software license registration details, an d ser vice contract length for purchased software installed on the MX9. Note: Following image is a sample screen. Y our License Manager panel may show more tabs, e .
5 - 42 Managed Programs This panel displays the install history for .NET managed programs. The list is read only . See Remove Programs (page 5-53)..
5 - 43 Memory These panels repor t the current state of vir tual memor y . Main The split between Storage memor y and Program memory is not adj ustable . Storage Card The pop-up list shows all mounted storage, both fix ed and remov able. The Fi nd prompt at the b ottom of the screen launches the Search utility .
5 - 44 Mixer The MX9 has a speaker located abov e the scan button. It is activ e when a headset is not connected to the device. Use the settings on these pa nels to adjust the volume , record g ain and sidetone fo r microphone in put, speaker and speaker output.
5 - 45 MX9WM Options Set MX9 specific device options . Options th at cannot be edi ted by the user are dimmed. Commu nication By default, TCP/IP v ersion 6 is enabled and dimmed on the MX9. By default, the Remote Deskt op Autologin is disab led. T ap this check box to enable Remote Desktop Autologon.
5 - 46 Misc. CapsLock and T ouch Screen Disable are disabled and dimmed. Enable K eypad Backlight is enabled b y default. Unchec k this check bo x to disable the k eypad backlight. Enable Ethernet on AC P ower and Battery are enabled and dimmed. Ether net is only available when the MX9 is dock ed in a p owered desktop cradle.
5 - 47 Status P opup When the Status popup window is enabled, and displa yed, it is placed on top of th e window in focus and hides any data beneath it. The Status P opup win dow is closed b y pressing the assigned Status User or Status Admin key sequence.
5 - 48 P eripherals This panel is u sed to enable and disable the touch screen heat er and scan window heater, flashlight time dela y to Off, and GPS On/Off . Settings hav e no effect if module is no t installed. Heaters Note: Settings have no effect if the touch scre en / scan window heaters are not installed.
5 - 49 Flashl ight Note: Setting has no effect if the flashlight is not installed. Select an option to set the timeou t for the flashlight. Options are: •1 m i n u t e •2 m i n u t e s •3 m i n .
5 - 50 GPS GPS presence is display ed on the GPS panel. P ower can be toggled on or off only when a GPS is installed. The def ault setting is Off. Regional Settings.
5 - 51.
5 - 52 Registry Choose an M X9 softwa re reload scheme . Load User Defaults Button When tapped, a standard load file dialog is opened, to allow the user to pick a Registry Save (.RSG) file. The applet then copies the specified User registr y file to the Active registry .
5 - 53 Remove Pr ograms This panel is used to uninstall programs. The Remov e Program listing is for all progr ams installed via ActiveSync or via a CAB file.
5 - 54 Align Screen T ap the Align Screen button. The align screen opens and disp lays a large cross-hair in the middle of the screen. T ap the middle of the cross-hair as it moves around the scre en. When the process is complete, the General screen is dis- play ed.
5 - 55 Te x t S i z e T ap the marker and slide it a cross the bar . As the marker mov es, the e xample te xt increases or decreases. T ap ok and the change is saved.
5 - 56 T ask Manager This panel displa ys all r unning tasks as well as the memor y and CPU bandwidth be ing used by each task. T apping on the column headings at the t op of the screen sor ts the ta sks by the contents of that column. T appin g the same heading a second time rev erses the sor t order of that column.
5 - 57 WA N These panels can be used to set the parameters f or the wireless Wide Area Network (WAN) on the MX9. The W AN is a f or m of wireless network that uti lizes a cellular network in stead of the spread spectru m network most used by wireless Local Area Networks (LAN).
5 - 58 Initial Setup 1. Enable the radio by tapping th e Admin Login button on the Connection panel (the Connect button is dimmed). 2. Enter the password in th e Admin Password Entry popup te xt box. The default ca se-sensitive passwo rd is LXEW- WAN.
5 - 59 Connection The Connect button controls Connect/Disconnect operation and the caption of the button changes ba sed on the con- nection status. The Connect bu tton is dimmed when the radio is disabled or absent. T ap the Connect button to begin a connection w ith a WWAN.
5 - 60 • Password • APN (Access Point Name) Note: Some fields may not require an entry. Contac t your system a dministrator for the in formation nee ded.
5 - 61 TCP/IP The TCP/IP tab contains a check box f o r indicating that TCP/IP parameters are to be obtained from the ne twork DHCP server . This tab also contains fields for entering a static IP address and th e addresses of the primar y and secondar y DNS ser vers , if DHCP and D NS are not used.
5 - 62 A utoconnect The Autoconnect tab contains two checkbo xes . A utomatically connect to networ k when device is turned on . When thi s check bo x is enabled (checked) the radio auto- matically connects to the network when the device is turned on (power b utton is pressed).
5 - 63 Admin The Admin tab provides the ability to change th e configurat ion pass word (see the Connecti on panel), enter Identifica- tion numbers f or the SIM card, and provi des a button to disable/enab le the radio . Pa s sw o r d Enter a new pass word, then re-enter the same passw ord.
5 - 64 About The About tab d isplays inf orm ation about the WW AN radio and the cu rrent network connect io n. The About tab displays the SW V ersion, FW V ersion and Seri al Number of the radio if there is a W AN radio installed in the device. the Local Phone Number shows the subscriber’ s own number from the SIM card.
5 - 65 Connections P anel Beam Enable or disab le receiving OBEXdata be ams, either by IrD A or Bluetooth. Note: The MX9 does not support beaming. The default setting f or Bea m Settings is Disabled as the MX9 does not suppor t beami ng. OBEX oBject EXchange A communications protocol used to excha nge information between mobile devices.
5 - 66 Connections Configure connections to a host PC. Advanced P anel Options:.
5 - 67 Domain Enroll Enroll in Active Directory . T o begin enrollment, tap Enroll in the Status ba r . Contact your system administrator fo r the applicab le inf or mation to com- plete the screens.
5 - 68 Netw ork Cards This panel displays a listing of networ k adapters. The list is bas ed o n drivers installed i n the registr y whethe r the adapter i s actually suppor ted by the hardware or not.
5 - 69 Wireless Manager Provides inf or mation on the cu rrently connected wirele ss network(s). The following image is an e xample only . If more than one wireless device is being managed, the All bar is display ed. T ap the All bar to disable/enab le all wireless de vices at once.
5 - 70 Miscellaneous Star t P anels Standard Micr osof t Applications Note: The intent of this segment is to document standard Microsoft applications loaded on the MX9. Documentatio n only consists of a panel and minimal explan ation. These are st a ndard Microsoft small form applica tions for which help is available on the MX9 and the Internet.
5 - 71 Address Book Address book application. Contacts can be synchronized with PC Outlook address book using ActiveSyn c. Email Email application. Can be synch ronized with PC Outlook email using ActiveSync or it can synchronize with an Exchange server.
5 - 72 File Explorer File Explorer displays a structur ed picture of files on the system. Getting Started This application provides several wizard s to walk a user through device configuration.
5 - 73 Help Access Windows Mobile help system on the MX9 . Options to search using Windows Live Search are available. Windows Live Messenger Windows Live Messenger.
5 - 74 Notes Notes. Notebook application. Sel ect Menu > Vi ew Recording Toolbar to create an audio note. Can be synchronized with PC Outlook notes using ActiveSync. Pictures and Video Pictures and Video. Picture/video viewer app lication. Can be synchronized with PC My Documents folder using ActiveSync.
5 - 75 Ta s k s Tasks. Task list application. Can be synchronized with PC Outlook task list using ActiveSync. T ext Messaging Text Messaging application. Can be synchronized with PC Outlook email using ActiveSync or it can synchroni ze with an Exchange server.
5 - 76 Windows Live Setup Windows Live. Sign in to Microsoft Windows Live online service. Internet access required. Windo ws Media Windows Media. Audio visual mana gement program.
5 - 77 Internet Explorer Mobile Set options for Internet connectivity . The navigation icons change state based on the web page contents. Navigation Icon Action Navigation Ico n Action Add folder Favo.
5 - 78 Options.
5 - 79.
5 - 80 Office Mobile A suite of business related applica tions. Files can be crea ted, opened, viewed, sa ved in diff erent f or mats, etc. Note: For Microsoft Of fice Mobile instru ction for Word, PowerPoint, Excel and O neNote, refer to commercially availabl e Microsoft Office Mobile user guides.
5 - 81 W ord Mobile Open, view , edit documents. Formats are sav ed. Spelling check er , cut and pa ste are availab le, undo and redo com- mands. Select Menu > Opti ons to change default settings. OneNote Mobile Open, view , edit text-only notes. Select Menu to change default settings.
5 - 82 Remote Desktop Using Remote Desktop Mo bile, you can log on to a remote computer (host) running T er minal Ser vices or Remo te Desktop and use all the programs av ailable on that computer from your mobile de vice.
5 - 83 1. Configure the radio. 2. Enter the name of th e computer to which you want to connect. If n eeded, enter the port number at the end of the computer name ( remotecomp utername:portnumber ). 3. Enter the user name , password and domain. 4. Tap the Save password check box if it is blank.
5 - 84 Using ActiveSync Requirement : ActiveSync (v ersion 4.5 or higher for Windo ws XP host computers) must be resident on the host (desktop or laptop) computer . Windows Mobile Device Center (v ersion 6.1 or high er) is required for a Windo ws Vista or higher host computer .
5 - 85 • It is not necessary to connect the power connector on the cable in order to use ActiveSync. Explore F r om the ActiveSync Dialog on the host computer , ta p the Explor e button, which allows you to explore the MX9 from the PC side, with some limita tions.
5 - 86 ActiveSync Help Issue : ActiveSync icon on the host computer does not tu rn green after connecting USB cable from MX9. Solution: 1. Disconnect MX9 USB cable from the host computer. 2. Suspend/Resume or Restar t the MX9. 3. In ActiveSync > File > Co nnection Settin gs on the host computer disable Allow USB Connections and tap OK .
5 - 87 Install HSM Connect 1. The HSM Connect installatio n file is on the Getting Started Disc. 2. Download the files to a location on yo ur host PC hard d rive. 3. Execute th e setup file that was copied to the host PC. This setup program installs the HSM Connect utility.
5 - 88 6. Tap the OK button to dismiss the About CERDisp dialog bo x on the MX9 desktop by tapp ing the OK button in the HSM Connect window on the PC desktop. The dialog box automatically time s out an d disappears afte r approxi- mately 20 seconds. 7.
6 - 1 6 AppLoc k (Application Loc king) Intr oduction AppLock is designed to be run on Windows based de vices only . The AppLock progr am is installed before shipping. Configuration parameters are specified by the AppLock Administ rator for the MX9 end-user .
6 - 2 Administration Mode Administration mode gives full access to the mobile de vice, hardware and softw are configuration options. The administrator must enter a valid pass word (when a pass word has already been assigned) before access to Administration mode and configuration opti ons are allowed.
6 - 3 P ass wor ds A passw ord must be configured. If the pass word is not configur ed, a new de vice switches into Administration mode without prompting f or a password.
6 - 4 Hotkey (Activ ation hotkey) If the mobile device uses AppLock to allow the user to switch betw een applications, the default Activa tion key is Ctrl+Spc . The ke y sequence switches the f ocus betw een one application and ano ther . Data entry affects the application runn ing in the foreg round onl y .
6 - 5 Application Configuration The default Administrator Hotke y sequence is Shift+Ctr l+A. Administrator mode allows access to all features on the de vice. When the hotkey is pressed to s witch into Administrator mode, a pass word prompt is displaye d (if a p ass word has been configured ).
6 - 6 Inter net Default is Disab led. Enable the Inter net checkbo x to use the End-user In tern et Explorer (EUIE.EXE) When the checkbo x is enabled, the Inte r net Menu and Inter net Status are availab le. See the section titled End User Internet Explorer (EUIE) (page 6-4) for more details.
6 - 7 Launch Button When the Laun ch button is clicked, it displa ys the Lau nc h options panel for the Filename selected on the Administra- tion panel. Note: Launch order is determined by the Order specified in the Appli cation tab. The Order value does not have to be sequential.
6 - 8 A uto Re-Launch Def ault is Enab led. When enabled f or a specific appl ication. automati cally re-launches it (subject to the specified A uto Re-Launch Delay in seconds) after it termin ates. This option allows the Admi nistrator to disable the re-launch operation.
6 - 9 Allow Close Def ault is Disa bled. When enabled, the associ ated application can be clos ed by the end-user. This option allows the administrator to configure applications that consume system resour ces to be terminated if an error condition occurs or at the end-user’ s request.
6 - 10 Setting a P asswor d in the Security P anel Mov e the cursor to the P ass word text bo x. The passw ords ente red in the P assword and Confirm Pass word fields must match. P ass words are case sensitiv e. When the us er exits th e Administrator pan el, the two pass word s are compared to v er ify that they match.
6 - 11 Status P anel Use the Status panel to view the log of pre vious AppLock o perations and to configure which messages are to be recorded during AppL ock operation. Status information is stored in a specific location on th e storage device and in a specific logfile specified by the Administra - tor .
6 - 12 Log Note: If a level higher than Error is selected, the stat us should be cleared frequen tly by the administrator. In addition to the three view le vels the administrator can se le ct that all status information be logged or tur n off all status inf or mation logging comple tely .
6 - 13 AppLock Err or Messages Any messages whose first word ends in ‘ing’ is output prior to t he action described in the me ssage. F or example , “Switching to admin-hotke y press” is logged after the a dministrator has pr essed the hotkey b ut prior to star ting the switch process .
6 - 14 Cannot find kbdhook.dl l The load of th e ke yboard filter fa iled. This occurs when the dll is missing or is corrupte d. Look in the Windows director y for kbdhook.dll. If it exists , delete it. Also delete AppLock.e xe from the Windows director y and reboot the unit.
6 - 15 Enter AppLockEnumWindows In order for AppLock to control the application bein g lock ed so it can prev ent t he application from exiting, AppLock launches the application and has to wait until it has crea ted and in itialized its main window .
6 - 16 Exit T oAdmin Exiting the function that handles the mode switch into admin mode. LOG_PROCES SING Exit T o User Exiting the us er mode s witch function. LOG_PROCES SING Exit T oUser-Registr y read failure The AppNam e value does not e xist in the registr y so user mode canno t be entered.
6 - 17 Loading keyboard hook When AppLock first loads, it loads a dll that contains the ke yboard hook processing. Th is message is logged pr ior to the load attempt. LOG_PROCES SING Open failure The status information is being sav ed to a file and the file open has failed.
6 - 18 Registr y read failure The regi str y re ad failed. The registry information read when this messag e is logged is the app lication information. It the Administration ke y cannot be opened or if the AppName value is missing or empty , this error is logged.
6 - 19 Timeout looking for app window After the ap plication is launched, AppLock must w ait until the a pplication has i nitialized itself before proceeding.
6 - 20.
7 - 1 7 Bluetooth Configuration Intr oduction Discover and manage pairing with nearby Bluetooth devices. Contact Technical Assistance (page 16-1) for upgr ade av ailability if your Bluetooth panels are not the same as the panels presented in this section.
7 - 2 Bluetooth icon (at the bottom of the T oday or desktop panel) state and Bluetooth device icon stat es change as Bluetooth devices are discov ered, paired, connected and disconne cted. There may be audible or visual signals as paired de vices re-connect with the MX9.
7 - 3 Initial Configuration 1. Open the Bluetooth control pa nel or tap the Bluetooth icon. 2. Tap the Settings Tab. 3. Change the Computer Friend ly Name at the bottom of the Settings panel. The Blue tooth MX9 default name is determin ed by the factory installed software version.
7 - 4 Bluetooth Devices The Bluetooth Devices tab displa ys any de vice pre viously discovered and paired with the MX9. Clear Button When the Clear button is tapped, the Bluet ooth client de letes all devices from the De vice table that are not currently paired.
7 - 5 Discov ering 1. Tap the Discover button to locate all discoverable Blu etoot h devices in the vicinity. The D iscovery process also que- ries for the unique iden tifier of each device discovered. 2. Tap Stop at any time to end the Discover and Qu ery for Unique Identifier functions.
7 - 6 An icon with a red background indicates the de vice's Bluetooth connectio n is inactive . An icon with a white background indicates the device is connected to the MX9 and the devi ce's Bluetooth connection is active . Double-tap a de vice in the list to open the device proper ti es menu.
7 - 7 Bluetooth D evice Men u 1. After the Discover butto n has been tapped and there are dev ices liste d, tap on a device in the list to highlight it. 2. Double-tap the highlighted device to di splay the Bluetooth Device right cl ick menu. The Blueto oth device does not need to be active.
7 - 8 Bluetooth Pr oper ties Data on the Bluetooth Proper ties panel cannot be cha nged by t he user . The data display ed is the result of the device Quer y performed dur ing the Di scov er y process. The Status dialog box reflects the curr ent state of the highlighted device .
7 - 9 This option is Enabled (check ed) by def ault. Disable this opti on to inhibit MX9 connection initiated by a Bluetooth scanner . Computer is discov erable This option is Disabled (uncheck ed) by def ault. Enable th is option to ensure other de vices can discov er the MX9.
7 - 10 Options Repor t when connection lost This option is Enabled by def a ult. There ma y be an audio or visual signal when a co nnection between a paired, active device is lost. A visual signal may be a dialog bo x placed on the disp lay notifying th e us er the conne ction between one (or all) of the paired Bluetooth de vices has stopped.
7 - 11 About This panel shows the Computer F riendl y Name (that other devices ma y discover during their Discovery and Quer y pro cess), the Bluetooth Client MAC address, and software v ersion lev e ls.
7 - 12 Easy P airing and A uto-Reconnect The Bluetooth module can establish relationships with new de vices after th e user taps the Discover button. It can auto- reconnect to devices pre v iously known b ut which have gone out of range and then returned within range.
7 - 13 Locate the bar code label, similar to the sample shown abov e, attached to the MX9. The label is the Bluetooth address identifier for the MX9. The mobile Bluetooth scanner / imager requ ires this inform ation before disco vering, pair ing, connecting or disconnecting can occur .
7 - 14 Bluetooth Remote De vice LED Upon star tup, if the remote Bluetooth sc anner sounds a long tone, this means the sc anner has not passed its automatic Selftest and has entered isolation mode. If the scanner is reset, the sequence is repeated. Co ntact Technical Assistance (page 16-1) f or help .
8 - 1 8 Data Collection W edg e Intr oduction Set scanner/imager keyboard wedge parameters , enable or disable symbologies from being scanned, scanner icon appearance, activ e scanner por t, and scan ke y settings. Assign baud rate , par ity , stop bits and data bits for a vailable COM por ts.
8 - 2 Data Pr ocessing Over view Bar code data processing inv olves se veral steps . Some steps may be skippe d during the processin g depending on user selections on the Symbology Settings panels. The steps are presented below in the order th ey are perf or med on the scanned data.
8 - 3 Main T ab The Data Collection W edge supp or ts up to three concurrent data collection devices. F or example, the internal scanner could be used to collect data at the same time a Bluetooth scanner is paired and/or a ser ial device is attached to COM1.
8 - 4 Continuous Scan Mode Continuous scan mode is only av a ilable if the MX9 is equ ipped with a Symbol scanner . Continuous scan mode dra ws power from the main batter y ev er y time a scan read/decode sequence is performed. Enabling Continuous Scan Mode will ensure the laser i s alwa ys on and decoding.
8 - 5 COM1 T ab Integrated laser scanner def ault values are 9600 Baud, 8 data bits, 1 stop bit and No parity . If these values are changed, the default v alues are restored after a cold boot or reflashi ng. Note: COM1 does not support 5V switchab le power on Pin 9 fo r tethered scanners connected to the MX9 I/O port.
8 - 6 Notification T ab Internal Scanner Sound This panel togg les inter nal scanner soun ds on and of f. Internal scanner sound, by default, is enab led.
8 - 7 V olume and Vibration Since the Data Collection Wedge uses the operating system interface to emit sounds /beeps, if the v olume/vibrate icon is set to anything other than On, W edge b eeps do not sou nd. Wedge vibration is not aff e cted by the System setting.
8 - 8 Data Options T ab Bar code manipulatio n parameter settings on this tab are applie d to th e incoming data resulting from successful bar code scans sent to the MX9 for processing. Note: The Data Op tions tab contains only thos e options available for one typ e of decoding engine.
8 - 9 For MX9 with Hand Held Products Decoding Engine Data Collection Wedge enables or disab les the bar code at the imager as well as enabling or disabling the bar code processing in the Wedge softw are. The HHP Proper ties button is only present if the MX9 is equipped with a Hand Held prod ucts imager .
8 - 10 • The external scanner operatio n cannot be controlled by the MX9 sca nner driver; therefore, a ‘good’ beep may be sounded from the external scanner even if a bar code from an external scanne r is rejected because of the configu ration specified.
8 - 11 Each time a Symbol ogy is changed, the setting s are saved as soon as ok is click ed. Settings are also saved when a ne w Symbology is selected from the Symbo logy drop down list. Clear Button This button will erase any programmed ov erride s, returni ng to the default settings for the selected symbology .
8 - 12 Enable, Min, Max Enable This checkbox enables (checked) or disab les (u ncheck ed) the symbol ogy field. The scanner dr iver searches the beginning of the bar code data for the type of ID specified in the Data Options tab -- Enable Code ID field plus any custom identifiers.
8 - 13 Barcode Data Matc h List The Barcode Data panel is used to str ip data that matches th e en tr y in the Match l ist from the bar co de. Enter the data to be stripped in the text bo x and tap the Inser t or A dd button. The entr y is a dded to the Match list.
8 - 14 together. More than o ne * in a configu ration string is not allowe d. (The User Interface will no t prevent it, but results would not be as expected, as only the first * is used in parsing to match the string.) • The question mark wildcard ? may be used to match any sing le character in the incoming data.
8 - 15 Symbologies The Code ID dr op-down bo x filters th e av ailable symbologies, in the Symbolo gy drop down bo x, by the selected Code ID . When a Hand Held Products imager scan en gine is instal led, AIM, Custom and HHP symbologies are di splay ed.
8 - 16 HHP Symbologies Advanced proper ties are availab le when an integrated Hand He ld Products imager is insta lled. Advanced proper ties are applicable regardless of the ID type select ed (AIM or HHP). HHP = Hand Held Products. Not all HHP symbolog ies hav e Advanced options.
8 - 17 Codabar - Adv anced Pr oper ties Check Characte r Required – When enabled, the check character is required. Def ault is disabled. T ransmit – When enabled, the check character is transmitted. Default is disabled. Start / Stop Character T ransmit – When enabled, the star t / stop char acters are transmitted.
8 - 18 Code 39- Adv anced Properties Check Characte r Required – When enabled, the check character is required. Def ault is disabled. T ransmit – When enabled, the check character is transmitted. Default is disabled. T ransmit Star t / Stop Characte r – When enabled, the star t / stop characters are transmitted.
8 - 19 Read 5-Digit – When enable, tr ansmit the 5 digit addenda. Default is disabled. Required – When enabled, only transmit bar codes with a 2 or 5 digit addenda. Default is disab led. Inser t Sepa rator – When enabled, inser t a space between the code and addenda.
8 - 20 Interleaved 2 of 5 - Adv anced Properties Check Characte r Required – When enabled, the check character is required. Def ault is disabled. T ransmit – When enabled, the check character is transmitted.
8 - 21 Mesa - Adv anced Properties UPCA – When enabled, decode UPCA Mesa. Default is disab led. EAN13 – When enabled, decode EAN 13 Mesa. Def ault is disabled. Code39 – When en abled, decode Code 39 Mesa. Default is disab led. Code128 – When enabled, decode Code 128 Mesa.
8 - 22 MSI Plessy - Adv anced Pr oper ties T ransmit Check Character – When enabled, transmit the check character . Default is enabled..
8 - 23 OCR Pr oper ties - Adv anced Pr operties Font – Font selection. Def ault is disabled. • A = OCR A • B = OCR B • Money = OCR Money • MICR = Magnetic Ink Character Recognition Direction – Decoder reads OCR fonts in an y direction, bu t setting direction parameter co rrectly can increase decoding speed.
8 - 24 2. To read the same string with a modulo 10 check digit in the seve nth character position, use the following template: aaaaaac Then enter 0123456789 for the Chec k parameter .
8 - 25 P osicode - Advan ced Properties Limited La bels – Select the type of Posicode Limited labels: • None • A – Posicode Limited A • B – Posicode Limited B T elepen - Ad vanced Pr operties Origina l Output – When enabled, output is Or iginal T elepe n.
8 - 26 UPCA - Adv anced Pr oper ties T ransmit Check Character – When enabled, transmit the check character . Default is enabled T ransmit Number System Digit – When enabled, transm it the number system digit. Default is enab led. Addenda Read 2-Digit – When enabled, transmit the 2 digit addenda.
8 - 27 UPCE0 - Adv anced Pr oper ties Note: The UPCE0 and UPCE1 parameters are alw ays set to match each o ther. Therefore if a change is made to a parameter to either the EPCE0 or UPCE1 Advanced Properties that same chan ge is automatical ly made to the Advanced Properties for the other symbology.
8 - 28 UPCE1 - Adv anced Pr oper ties Note: The UPCE0 and UPCE1 parameters are alw ays set to match each o ther. Therefore if a change is made to a parameter to either the EPCE0 or UPCE1 Advanced Properties that same chan ge is automatical ly made to the Advanced Properties for the other symbology.
8 - 29 HHP Properties When the MX9 is equip ped with a Hand Held Pro ducts imager , this option is used to configure imager parameters. Option Action Centering The centering feature is used to allow the user to accurately scan a selected ba r code among a group of bar codes that are locate d closely toge ther .
8 - 30 Aim Time Duration of the imager aim beam in 0.1 second increments. V alid:0 – 50 (0 to 5 seconds) Def ault:0 Lights Specifies if the imager's lights and aimer sh ould be left on d uring the e ntire decode process. The default is disabled.
8 - 31 Ctrl Char Mapping The Ctrl Char Mapping button activates a dialog to define the operations the Data Colle ction Wedge perf orms on con- trol characters (values less than 0x20) embedded in b ar co des. Control characte rs can be replace d with user-defined text which can include hat enco ded or hex encoded v alues .
8 - 32 List Box The list box sho ws all user-defined control characters and their assigne d replacements. All replacements are enclosed in single quotes to delimit white space that has been assigned. Delete This button is gra yed unless an entr y in the list box is highl ighted.
8 - 33 Entering data into both the Name and ID Code fields enables the Add button. T ap the Add button and the data is added to the ne xt empty location in the Custom ID list. Insert T ap on an empty line in the Custom ID list. The Add button changes to Inser t.
8 - 34 Bar Code Pr ocessing Examples The follo wing table shows e xamples o f stripping and prefix/s uffix configu rations. The e xampl es assume that the scan- ner is configured to transmit an AIM identifier .
8 - 35 Length Based Bar Code Stripping Use this procedure to create symbolo gy rules for two bar codes with the same symbol ogy but with diff erent discrete lengths. This procedure is not applicable for bar codes with v ariable lengths (falling between a maximum v a lue and a mini- mum val ue ).
8 - 36 5. Tap the Barcode Data button. 6. Tap the Add button . 7. Add the data for the match codes. 8. Refer to the previous section Barcode Data Match List (page 8-1 3) for instruction.
8 - 37 Pr ocessing T ab The Processing tab contains a user configurable ke y delay that applies to scanned bar co des as they are input when Remote Desktop is the application with the input focus . Note: Settings on this panel ha ve no effect when RFTerm is the applicatio n w ith the in put focu s.
8 - 38 About T ab The About tab lists the version of the Data Collection W edge ( DCWedge) software and the type of scanner/imager installed in the MX9.
8 - 39 Hat Encoding Hat Encoded Characters Hex 00 through AD ..
8 - 40 Hat Encoded Characters Hex AE through FF ..
9 - 1 9 Enhanced Launch Utility Intr oduction The launch utility has two functions: • Process registry based Launch items • Process script based Launch items.
9 - 2 • The Order field is used to force a seq uence of events; Order=0 is first, and Order=9 9 is last. Two items which have the same order are installed in the same pass , but not in a predictable sequence. • The Delay field is used to add a delay after the item is loa ded, before the next is loaded.
9 - 3 Script Based Launch Items Note: The Script Based Lau nch items (documented here) a re processed after the Registry Base d Launch items. The Enhanced (scr ipt based) por tion of th e Launch utility provides se veral f eatures: • Launch .CAB file • Run .
9 - 4 Command line structure Each command takes up one line. Every command uses the format: COMMAND,PARAMETER1,PARAMETER2,...e tc. P arameters are separated b y a single comma. If a parameter requires a comma within it, the whole parameter must be enclosed in quote mar ks (").
9 - 5 Commands Suppor ted by Launc h The commands suppor ted by Launch are detailed below . Square br ack ets indicate that a paramet er is opti onal. Characters in Italics represent a variable , and not a literal.
9 - 6 DelRegKe y ElseIf ElseIfFile Description D eletes a specified registr y subkey . Syntax Delregkey , key,subkey Pa r a m e t e r key : The abbreviated major registr y ke y where you want to delete the subke y . Can be on e of: • cr or hkcr (HKEY_CLASSES_ROOT) • cu or hkcu (HKEY_CURRENT_USER) • lm or hklm (HKEY_LOCAL_MACHINE).
9 - 7 EndIf EndIfFile EndIfT erm FCopy Description En ds conditional command bloc k begun with the previous IF command. Syntax EndIf Pa r a m e t e r N one Example See IfFile (page 9-8). Notes Results are unpredictable if not paired proper ly with If.
9 - 8 IfFile IfT erm Launch Description Be gins the conditional ex ecution of a bloc k of commands only if the specified file exists . Syntax IfFile , fil e Pa r a m e t e r file : The path and filename to determine if the commands should be ex ecuted Example IfFile,S ystemMyData.
9 - 9 LaunchCmd Message Mkdir Description R uns a program with arguments. Syntax Launch cmd , program,argum ents,wait-code P arameters program : The full path and filename of the program to be ru n. arguments : The command l ine arguments for progr am.
9 - 10 Rmdir SetRegData Description R emov es a director y . Syntax Rmd ir , dir P arameters dir : The full path and name of the director y to be remov ed. Example rmdir,Pr ogram FilesMyApp Notes A director y canno t be remov ed if it contains files or subdirector ies.
9 - 11 SetRegKe y Shortcut Description Ad ds a sub ke y to the registry . Syntax Setregkey , key,subkey P arameters key : The abbre viated majo r registr y key where y ou want to create the subke y . Can be one of: • cr or hkcr (HKEY_CLASSES_ROOT) • cu or hkcu (HKEY_CURRENT_USER) • lm or hklm (HKEY_LOCAL_MACHINE).
9 - 12 Launch Err or Messages Launch displays a message if it encounters an error during the processing of a scri pt. It is possible to get cascading error messages, as Launch does not stop processin g the scrip t if it enc oun ters an error .
9 - 13 Example Script File iffile,Systemapplock.cab launchcmd,Windowswceload.exe,"/n oaskdest /noui Systemapplock.cab",w launch,Windowsapplockprep.exe,c endiffile launchcmd,Windowswceload.exe,"/n oaskdest /noui Systemwedge.cab",w iffile,Systemsummit.
9 - 14.
10 - 1 10 Enabler Installation and Configuration Intr oduction This section discus ses Honeywell suppor ted features with Wa velink A v alanche Mobile Device Ser vers .
10 - 2 Enabler Uninstall Pr ocess T o remov e the Av alanche Enabler from the MX9: • Delete the Avalanche folder lo cated in the System directory. • Warm boot the MX9. The A valanche f older cannot be deleted whi le the Enabler is running. See Stop the Enabler Service (page 10-2).
10 - 3 T o configure the Av ala nche Enabler management of the network and wireless settings: 1. Open the Ena bler Settings Panels by tapping the Enabl er icon on the desktop. 2. Select File > Settings . 3. Select the Adapters tab. 4. Choose settings for the Use Manual Settings parameter.
10 - 4 User Interface The Enabler can be configured and controlled manually through the user interface on the MX 9. This section detai ls the functionality that can be controlled by the user or system administrator . Screen displays sho wn in this section are designed to presen t the end-user with inf or mation graphically .
10 - 5 File Menu Options Connect The Connect option under the File menu allows the user to init iate a manual connection to the Mobile Device Server . The connection meth ods, b y default, are wireless and COM connections. Any updates av ailable will be applied to the MX9 immediately upon a successful connecti on.
10 - 6 A valanche Update using File > Settings Use these menu options to setup the Av alanche Enabler on the MX9. Change the settings and then sav e the changes (reboot) before connecting to the network.
10 - 7 Connection Avalanche Server Address Enter the IP Address or host name of the Mobile Device Server assigned to the MX9. Check Serial Connection Indicates whether the Enabler should first check f or serial po r t connection to the Mobile Device Ser ver bef ore checking f or a wireless connection to th e Mobile Device Server .
10 - 8 Execution Note the dimmed options on this MX9 panel. This menu opti on is designed to manage downloaded application s f or automatic e xecution upon star tup. Auto-Execute Selection An application that has been installed with the A valanche Management system can be run automatically f ollowing each boot.
10 - 9 Contact On Star tup – Connect to th e Mobile Device Server when the Enabler is accessed. On Resume – Connect to the Mobile Device Server when resuming from Suspend mode. On IP Change - Connect to the Mobile Device Server when the IP address of the MX9 changes.
10 - 10 Preferences F or best results, use AppLock to manage the taskba r . App Lock is resident on e ach mobile device. Administration By default, Keep settings unlocked for 10 minutes is disabled (checkbo x is blank). Applic ation Startup Behavior of the Enab ler when the MX9 boots up.
10 - 11 • Basic Output - General information is displayed. • Critical - Critical errors are displayed in addition to those above. • Error - Communication or configu ration problems are displayed in addition to those above. • Warning - Possible operation problems are displayed in addition to tho se above.
10 - 12 Scan Config F or best results use eXpress Config and eXpress Scan fo r this function. eXpress Sc an is included with the updated MX9 enab lers. Scan Config functionality is a standard opti on of the W av elink A valanche MC system b ut is not current ly suppor ted on the MX9.
10 - 13 Display The user inte rface f or the Enabler can be configured to dy namical ly change based on the st atus of the MX9 connection with the Mobile Device Ser ver . At startup Def ault is Half Screen. Op tions are Half screen, Hidden or Full screen.
10 - 14 Shortcuts F or best results use AppLock f or this function . AppLock is resident on ea ch mobile device. Configure shor tcu ts to other applications on the MX9. Shor tcuts are viewed and activated in the Programs panel. This limits the user’ s access to cer tain applications whe n the Enabler is controlling the mobile device display .
10 - 15 SaaS Use to configure the Enabler to connect with A valanche on Demand. This is a Software-as-a-Ser vice version of A va- lanche. Using either of the Saa S configuration option s below assumes the user has registered with Wa velink. Disable SaaS No SaaS connection is used.
10 - 16 Adapters Note: Review the network settings configura tion utilities an d the default val ues before setting All Adapters to Enable in the Adapters applet.
10 - 17 Manual Settings Pr operties) Do not enable Manage Wireless Settings for Summit Client devices . Note: Whe n you download a profile that is configured to manage network and wireless settings, t.
10 - 18 Status The Status panel displays the cu rrent status of the MX 9 network adapter selected in the drop down box. Note the a vail- ability of the Windows standard Refresh button. When the Wind ows Refresh button is tapped, the si gnal st rength, signal qua lity and link speed are refreshed for the currently selected adapter .
10 - 19 Exit The Exit option is pa ss word protected. The default pa ss word is leav e. The pass word is not case-sensitive . If changes were made on the MX9 Star tup/Shutdown tab screen, then after enter ing the password, tap OK and the f ol- lowing screen is displa yed: Change the option if desi red.
10 - 20 Using Remote Management 1. Configure the radio to connect to the network running the Mo bile Device Se rver. After the MX9 is connected, proceed to step 2. 2. If it is desired to configure the radio using the Summit pack age, add the configured packa ge to the Wavelink Avalan che MC Console and enable it.
10 - 21 3. Click Start. 4. Bar code 1 must b e scanned first. The scanned data is displa yed in the “Da ta” text box. The password, i f any, entered above is compared to the password entered whe n the bar codes were created.
10 - 22 7. The remaini ng bar codes may be scanne d in any order. After a bar code is scanned, that ba r code is removed from the “Remaining:” list and placed in the “Scanned:” list. Process Complete After the last bar cod e is scanned, t he settings are automatically applied.
11 - 1 11 Wireless Netw ork Configuration Intr oduction The Summit client de vice is either an 802.11g radio, capab le of both 802.11 b and 802.11g da ta rates or an 8 02.11a radio, capable of 802.11a, 802.11b and 802.11g data rates. The radio can be configured for no encr yption, WEP encr yption or WP A security .
11 - 2 Summit T ray Icon The Summit tray icon is display ed when: • The Summit radio is installed and active • The Windows Zero Config utility is not active • The Tray Icon setting i s On T ap the icon to launch the SCU .
11 - 3 Create a New Netw ork Connection 1. Tap on the Wi-Fi ico n. A list of available networks is displayed. 2. If the desired network is not displayed , tap Add New.
11 - 4 3. Enter the SSID of the desired network in th e Network name text box. Be su re to tap the This is a hidden network check box for a non-broadcast SSID.
11 - 5 Main T ab The Main tab displays inf o rm ation about the wireless client device including: • SCU (Summit Client Utility) version . • Driver version. • Radio Type (BG is an 802.11 b/g r adio, ABG is an 80 2.11 a/b/g radio). • Regulatory Domain is preset to either Worldwide or a location specif ic domain (FCC, ETSI, KCC or TELEC ).
11 - 6 The Auto Profile selection screen displa ys all currently co nfigured profiles. T ap on the check bo x for any profiles that are to be inclu ded in Auto Profile selection then ta p ok to sav e. T o enable A uto Profile, tap the On button on the Main tab .
11 - 7 • View radio status, software versions and regulatory doma in on the Main tab. • Access additional troubleshooting features on the Diags Tab (page 11-13). After Admin Login, the end-user can also: • Create, edit, rename and delete profiles on the Profile tab.
11 - 8 Profile T ab Note: Tap the Co mmit button to sa ve changes before leaving th is pane l or the SCU. If the panel is exited before tapping the Commit button, changes are not saved! When logged in as an Admin use the Profi le tab to manage prof iles.
11 - 9 Allows entry of WEP ke ys or pass phrase as required by the type of encr yption. Credentials Button Allows entry of a user name and passw ord, cer tificate name s, and other information required to authenticate with the access point. The inf or mation r equired depends on the EAP type.
11 - 10 Pr ofile P arameters P arameter Default Explanation Edit Profile Def ault A string of 1 to 32 alphanumer ic characters, establishes the name of the Profi le. Options are Default or ThirdP ar tyConfig. SSID Blank A string of up to 32 alphanumeric characters.
11 - 11 It is impor tant the Radio Mode parameter correspond to the Acce ss P o int (AP) to which the device is to connect. F or e xample, if this parameter is set to G rates only , the MX9 may only connect to APs set for G r ates and not th ose set f or B and G rates.
11 - 12 Status T ab This screen provides information on the radio: • The profile being used . • The status of the radio card (dow n, associated, authenticated, etc.
11 - 13 Diags T ab The Diags screen can be used for troub leshooting network traffic and radio connectivity issues. (Re)connect Button Use this button to apply (or reapply) t he current profile and attempt to associate or authenticate to the wireless LAN.
11 - 14 Global T ab The parameters on this panel can only be changed when an Admi n is loggin in. The current v a lues for the parameters can be view ed by the general user without requiring a password.
11 - 15 Custom P arameter Option Honeywell does not suppor t the proper ty Custom option. The parameter valu e is displa yed as “Custom” when the operating system registr y has been edited to set the Summit parameter to a value that is not av ailable from the param- eter’ s drop down list.
11 - 16 Ad Hoc Channel 1 Use th is parameter when the Radio Mode profile parameter is set to Ad Hoc. Specifies the channel to be used for an Ad Hoc connection to another client device . If a channel is selected that is not su ppor ted by the by the radio , th e default v alue is used.
11 - 17 TX Diversity BG: On A: Main Only How to handle antenna diversity when transmitting pack ets to the Access Po i n t . Options are: Main only (use the main ante nna only), Aux only (use the auxiliar y antenna o nly), or On (use diversity or both antennas).
11 - 18 A uth Timeout 8 seconds Specifies the number of seconds the Summit software waits for an EAP authentication request to succeed or fail. If the authentication crede ntials are stored in the active profile and the authentication times out, the association fails.
11 - 19 Sign-On vs. Stored Credentials When using wireless secur ity that requires a user name an d password, the Summit Client Utility off ers these choices: • The User name and Password may be entered on the Credentials scre en. If this method is selected, anyone using the de vice can access the network.
11 - 20 10. Verify the device is authent icated by reviewing the Stat us tab. When the device is property configured, the Status Tab (page 11-12) indica tes the device is Authenticated and the method used. 11. The sign-on scree n is displa yed after a reboot.
11 - 21 Windows Certificate Store vs. Cer ts P ath Note: It is important that all dat es are correct o n the MX9 and host computer s w hen using any type of cert ificate. Certificates are date sensitive and if the date is not correct authenticatio n will fail.
11 - 22 6. Tap to uncheck (and disable) the Use full trusted store check box. 7. Select the desired certificat e and tap the Select button to return the se lected certificat e to t he CA Cert text box. 8. Tap OK to exit the C redentials scre en and then tap Co mmit to save the profile chan ges.
11 - 23 Configuring Pr ofiles Use the instructions in this secti on to complete the entr ies on the Profile tab accord ing to the type of wirele ss security used by your netw ork . The instructions that follo w are the minimum r equired to successfully connect to a network.
11 - 24 WEP T o connect using WEP , ma ke sure the f ollowing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile. 2. Set EAP Type to None. 3. Set Encryption to WEP or Manual WEP (depend ing on SCU versi on). 4. Set Auth Type to Open.
11 - 25 LEAP T o use LEAP (without WP A), mak e sure the follo wing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile. 2. Set EAP Type to LEAP. 3. Set Encryption to WEP EAP or Au to WEP (depending on SCU version).
11 - 26 8. Enter the password. Tap OK then tap the Commit button. 9. Ensure the correct Active Profil e is selected on the Main tab and Warmboot. The SCU Main ta b shows the device is associated after the radio co nnects to the network.
11 - 27 PEAP/MSCHAP Note: The date must be prop erly set on the device to authenticate a certificate. T o use PEAP/MSCHAP , make sure the f ollowing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile. 2. Set EAP Type to PEAP-MSCHAP.
11 - 28 9. Enter the DomainUser name (if the Domain is required), otherwis e enter the User name. 10. Enter the password. 11. Leave the CA Certificate File Name blank fo r now. 12. Tap OK then tap Commit. Ensure the correct Active profile is selected on the Ma in Tab.
11 - 29 PEAP/GTC T o use PEAP/GTC , make sure the f o llowing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile.
11 - 30 12. Tap OK then tap Commit. Ensure the correct Active Profile is sele cted on the Main Tab. 13. See Windows Certificate Sto re vs. Certs Path (page 11-21) for more information on certificate storage. 14. Once su ccessfully aut henticated, import the CA certificate in to the Windo ws certificate store.
11 - 31 WP A/LEAP T o use WP A/LEAP , make sure the follo wing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile.
11 - 32 9. Enter the password. 10. Tap OK then tap the Commi t button. 11. Ensure the correct Active Profile is selected on the Ma in Tab and Warmboot.
11 - 33 EAP-F AST The SCU suppor ts EAP-F AST with automati c or manual P A C provisioni ng. With au tomatic P AC pro visi oning, the user cre- dentials, whether entered on the sav ed cr edentials scree n or the sign on screen, are sent to the RADIUS ser ver .
11 - 34 8. To use Stored Credentials, tap on the Credentials button. No entries are ne ce ssary for Sign-On Credentials with automatic PAC provisionin g as the user will be prompted for the User name and Password when connecting to the network.
11 - 35 EAP-TLS T o use EAP-TLS , make sure the f o llo wing profile options are used. 1. Enter the SSID of the Access Poi nt assigned to this profile.
11 - 36 10. Select a user certificate from the Wind ows certificate store. Use the Browse butt on to locate the User Cert from the certificate st ore. Highligh t the desired ce rtificate and press the Select button. The name of the ce rtificate is displayed in the User Cert box.
11 - 37 WP A PSK T o connect using WP A/PSK, mak e sure the f ollowing profile options are used: 1. Enter the SSID of the Access Poi nt assigned to this profile. 2. Set EAP Type to None. 3. Set Encryption to WPA PSK or WPA2 PSK. 4. Set Auth Type to Open.
11 - 38 Cer tificates Note: Refer to the Se curity Primer (available at www.honeyw ellaidc.com ) to prepare the Authentication Se rver and Access Point for communication. Note: It is important that all dat es are correct o n the MX9 and host computer s w hen using any type of cert ificate.
11 - 39 3. Tap the Download a CA certificat e, certificate chain or CRL lin k. 4. Make sure the correct root CA cert ificate is selected in the list box.
11 - 40 5. Tap the DER button. 6. To download the CA certificate, tap on the Download CA certi ficate link. 7. Tap the Save button and save the certificate.
11 - 41 8. Install the Root CA Certificate on the MX9. Installing a Root CA Cer tificate Note: This section i s only if the Win dows ce rtificate store is used. If the certificate store is not used, copy the certificate to the System folder or o ther path specified in the Summit Certs global parameter.
11 - 42 4. Tap the Request a certificate link. 5. Tap on the User Certificate link..
11 - 43 6. Tap on the Submit button. If there is a message box asking if you wa nt to confirm the request, tap Yes. 7. The User Certificate is issued. 8. Install the user certificate on t he requesting computer by clicking the Install this certificate link.
11 - 44 6. Uncheck Enable strong protection and tap Next . The certificate type must be PKCS #12 (.PFX). 7. When the private key is exported , you must enter the p a ssword, confirm the password and tap Next. Be sure to remember the password as it is needed when installing the certificate.
12 - 1 12 KeyM a p s Intr oduction The ke ypad is av ailable in a 62-k ey or 38-k ey configuration. The 62-ke y keypad is also a vailab le in an IBM 5250 configuration. • When using a sequence of keys that includes a sti cky key, pre ss the sticky key first, release it, then press the rest of the k ey sequence.
12 - 2 Alt mode AL T Alt mode Ctl mode CTL Control mo de Escape ESC Escape Space SPC Space Enter En ter Enter Capslock toggle Blue T AB Capslock is on or off Mapped Diamond 1 K ey Diamond 1 Use the Ke.
12 - 3 F20 Blue F10 F20 mode F21 SHFT F1 F21 mode F22 SHFT F2 F22 mode F23 SHFT F3 F23 mode F24 SHFT F4 F24 mode a A a (lowercase is the def ault) bB b cC c dD d eE e fF f gG g hH h iI i jJ j kK k lL .
12 - 4 NS H F T N N OS H F T O O PS H F T P P QS H F T Q Q RS H F T R R SS H F T S S TS H F T T T US H F T U U VS H F T V V WS H F T W W XS H F T X X YS H F T Y Y ZS H F T Z Z 11 1 22 2 33 3 44 4 55 5 66 6 77 7 88 8 99 9 0 (zero) 0 0 (zero) . (period) Orange SPC P eriod .
12 - 5 % SHFT 5 (number) P ercent sign ^ Orange Y Caret or circumfle x ^ SHFT 6 (number) Caret or circumfle x & Orange U Ampersand & SHFT 7 (number) Ampersand * Orange I (alpha i) Asterisk * S.
12 - 6 62-Ke y 5250 Ke ypad Overla y Ke yMap T o get this function Press these ke ys in this order Result / Notes Attention (Attn) CTL A 5250 Attn Clear (Clr) CTL C 5250 Clr Delete (Del) CTL D 5250 De.
12 - 7 Ctl mode CTL Control mode Escape ESC Escape Space SPC Space Enter Enter Enter Capslock toggle Blue T AB Capslock is on or off Mapped Diamond 1 K ey Diamond 1 Use the Ke ymap Control Panel to ch.
12 - 8 F20 Blue F10 F20 mode F21 SHFT F1 F21 mode F22 SHFT F2 F22 mode F23 SHFT F3 F23 mode F24 SHFT F4 F24 mode a A a (low ercase is the de fault) bB b cC c dD d eE e fF f gG g hH h iI i jJ j kK k lL.
12 - 9 MS H F T M M NS H F T N N OS H F T O O PS H F T P P QS H F T Q Q RS H F T R R SS H F T S S TS H F T T T US H F T U U VS H F T V V WS H F T W W XS H F T X X YS H F T Y Y ZS H F T Z Z 11 1 22 2 33 3 44 4 55 5 66 6 77 7 88 8 99 9 0 (zero) 0 0 (zero) .
12 - 10 % Orange T P ercent sign % SHFT 5 (number) P ercent sign ^ Orange Y Caret or circumfle x ^ SHFT 6 (number) Caret or circumfle x & Orange U Ampersand & SHFT 7 (number) Ampersand * Orang.
12 - 11 38-key K eypad K eyMap The follo wing keymap is used on an MX9 that is not r unning a T e rmin al Emulator . T er minal emulat ors use a sepa rate k eymap . A modifier ke y pressed after itself toggles that modifier ke y off. Any k ey press, other than a modifier k ey f oll owing any modifier ke y unsticks the modifier ke ys.
12 - 12 Backtab Orange T AB Backtab Cursor Up Up Arrow Cursor up one line Cursor Down Down Arrow Cursor down one line Cursor Right Bl ue Up Arrow Cursor right one space Cursor Left Blue Down Arrow Cur.
12 - 13 j Alpha 5 j k Alpha 55 k l Alpha 555 l m Alpha 6 m n Alpha 66 n o Alpha 666 o p Alpha 7 p q Alpha 77 q r Alpha 777 r s Alpha 7777 s t Alpha 8 t u Alpha 88 u v Alpha 888 v w Al pha 9 w x Alpha .
12 - 14 22 2 33 3 44 4 55 5 66 6 77 7 88 8 99 9 0 (zero) 0 0 (z ero) . (period) Orange SPC P e riod - Blue SPC Dash or min us sign / Blue 1 Re verse Solidus or Bac kslash Orange 1 Solidus or Forw ard.
12 - 15 ~ Blue 9 Tilde < Blue 7 Less than mark > Blue 8 More than mar k : Orange 0 (zero) Colon + Blue BKSP (Bac kspace) Plus sign ? Orange 8 Question mar k _ Orange 7 Underscore or hor izontal .
12 - 16.
13 - 1 13 Battery Charger Unpacking y our Battery Charger After you open the shipping ca r ton containi ng the product, take the f ollowing steps: • Check for damage during shipment. Report damage immedia tely to the carrier who delivered the carton.
13 - 2 Cautions and W arnings Battery Charger • There is a risk of explosion if th e MX9 Li-Ion battery in the charging pocket is rep laced by an incorrect type. Other batterie s or battery packs may burst causing injury or property damage. • Do not insert any other type of Li-Ion battery in the MX9 battery charging pocket.
13 - 3 Fr ont View 1. Battery Charging Pocket 2. Battery Charging Pocket LED 3. Battery Pocket Spring Clip 4. Battery Retaining Clip 5. AC Power port Installation Assemble the P ower Suppl y Assemble the A C adapter for the MX9 Battery Charger before connecting it to the charger .
13 - 4 Setup Place the batter y charger on a flat, horizontal, hard surface or f asten securely to a stable surf ace using the ke yhole open- ings on the bottom of the batter y charger . See Mounting. Do not inser t batter y packs until the batter y charger has finished powering up: 1.
13 - 5 Inserting a Batter y in to the Charging P ocket It is impor tant that batter y pa cks are in ser ted into the charging p ock et correctly . Inser ting the batter y incorrectly could res ul t in damage to the batter y pa ck or the charger . Do not “slam” the batter y pack into t he charging pocket.
13 - 6 NO LIGHT - on all char ge pockets No light means there i s no AC pow er av ailable f or the ba tter y charger or there is power but there are no batteries in any charging bay .
13 - 7 Charger Cleaning, Storage and Service Cleaning Unplug the charger from the power source bef ore cleaning or removing debris from charging pockets . Use only mild detergent with a slightly damp cloth to clean the outside of the charger . Do not use solvents or flammab le cleaners.
13 - 8 Do not store batter y packs in direct sunlight, on a metal surf ace, or anywhere the battery pack cannot cool down. Do not leav e the batte r y pack in a non-operating charger . The batter y pack may discharge through the charger rather than hold its charge.
14 - 1 14 Cradles Unpacking y our Cradles After you open the shipping ca r ton containi ng the product, take the f ollowing steps: • Check for damage during shipment. Report damage immediate ly to the carrier who delivered the carton. • Make sure the items in the carton match your order.
14 - 2 T ethered Scanners and the MX9 Cradles An MX9 powered cradle support s tethered scanner attachment. A powered cradle provides 5V po wer to a tethered scanner . The passive v ehicle cradle cannot suppor t tethered scann er attachment. There is no software in the cradles .
14 - 3 Battery Cleaning, Storage and Service Cleaning The batter y pack should not require cleaning unless it has be co me heavily soiled. Old or damaged batteries shou ld be disposed of promptly and properly . The best wa y to dispose of used ba tteries is to recycle them.
14 - 4 Fr ont View Back View Side View 1. MX9 Cradle Docking/Chargi ng Bay 2. MX9 Docked LED 3. Spare Battery LED 4. Table Mounting Holes 1. Spare Batte ry Charging Bay 2. Headset Audio C able port 3. AC/DC Power port 4. Serial port 5. Ethernet port 6.
14 - 5 T op View Desktop Mounting Footprint Bolts, w ashers, screws , screwdriver or wrench needed when a ttaching the MX9 desktop cradle to a protected flat surface are not supplied by Honeyw ell. P er iodica lly check the table mounting hardware and re-tighten if necessar y .
14 - 6 Assemble/Attach the A C P ower Adapter Note: Connect the cabl e to the cradl e first, then to an AC source. The external P ower Supply f or the cradle is shipped with the cradle. Contact Technical Assistance (page 16-1) if the re is no A C cable.
14 - 7 Desktop Cradle Connector Identifier s Connecting a Headset A udio Cable Fir mly press the cradle end into the MX9 Headset Audio por t (1) on the back of the cradle .
14 - 8 Spare Batter y LED Note: Spare battery charging does no t require an MX9 be docked in the docking bay. MX9 System Status LED Status when Doc ked The MX9 System Status LED i s lo cated at the top of the keypad. Docking and Undoc king the MX9 When the MX9 is in Suspend Mode it wakes up when it is docked in a po wered cradle.
14 - 9 A fully depleted spare batter y recharges in approximately f our hours in the MX9 pow ered cradle. Charging time may tak e longer if a tethered scanner , connected to the Seri al por t and drawing pow er from the cradle, is used. The spare batter y charger can recover a batter y that has had its safety circuit tripped.
14 - 10 Cradle is plugged into a live outlet, battery pack is inserted, but RED LED is OFF and no other LEDs are on, or all LEDs are off . Batter y pack is not making contact with char ging terminals in the batt er y well. F aul ty batter y pack. New battery pack, same result.
14 - 11 Using a P owered V ehic le Cradle Introduction V ehicle mounted cradles and brac kets are specifically desi gned for v eh icle mount applications.
14 - 12 Components Bef ore instal lation begins, verify you ha ve the applicable vehicle mounting brack et assembly components necessar y for your mount type. Fr ont View Back View 1. Docking Guide Pin (left) 2. Release Latch (left) 3. Docking Bay 4. Charge/Communicate p ort 5.
14 - 13 RAM Bracket Mounting RAM Brack et Assembly mounting holes are on the back of the cradle. The mounting screws fit in Pim nuts and are automat- ically secured. The number of RAM balls attached to the back of the ve hicle mount cradle are depen dent upon the desired RAM mount configuration.
14 - 14 V ehicle Cradle RAM Ball Assemb ly 1. Fasten the RAM ball with the circular mounting base (s hown in the middle in above image) to the vehicle. 2. Fasten the RAM ball with the rectangula r mounting base (shown on the ri ght in above image) to the back of the vehicle cradle.
14 - 15 DC/DC P ower Supply Installation, Scre ws on Side of Lid F or use with • 9000311PWRSPLY – Power Supply, 9-60VDC, 60W • 9000313PWRSPLY – Power Supply, 50-150VDC , 60W: If your DC/DC pow er supply does not look like the image abov e, see DC/DC Power Supply Installa tion, Screws on Top of Lid (page 14-18) for installatio n instruction.
14 - 16 Wiring Schematic Connecting to V ehicle P ower The vehicle cradle must be empty . The last connection must be to the vehicle power source . 1. Connect the power cable to the vehicle cradle. 2. Route the cable from the cradle to the DC/DC pow er supply .
14 - 17 6. Attach the stripped wire ends to the outp ut side of the DC/DC power supply. Note: The input block has V IN+ , V IN- and GND terminals. The output block has V O+ an d V O- terminals. 7. Connect the ground wire from the cr adl e to the GND terminal on the inpu t side of the DC/DC power suppl y.
14 - 18 DC/DC P ower Supply Installation, Scre ws on T op of Lid F or use with Honeywell power supplies: • 9000301PWRSPLY – Power Supply, 18-60VDC with cabl e • 9000302PWRSPLY – Power Supply, .
14 - 19 Wiring Schematic Connecting V ehicle Electrica l Supply 1. The vehicle cradle must be empty. 2. Begin by connectin g the power cable to the vehicle cradle. Work from this connection wi th the last connection being to the vehicle’s power source.
14 - 20 9. Wire colors depend on the type of device attached. Please refer to the Wiring Schematic for wire colors. 10. Use the looms and wire ties to secure all wiring as shown above , then reattach the lid. 11. Connect the DC to DC power supply to the vehi cle’s electrical system as directed below:.
14 - 21 V ehicle 12V Bare Wire Adapter P ar t Number : 9000A0 79CBL12ML3 V ehicle Cab le Connection (Fuse Not Shown) Connecting the P ower Cable to the V ehicle Note: Correct electrical polarity is required for safe and p roper installation. The cradle w ill not power on or function if the cable is connected with the polarity reversed.
14 - 22 Connecting V ehicle 12 VDC Suppl y 1. The power cable must be UNPLUGGED from the MX9 vehicle cradle. 2. While observing the fuse re quirements specified above , connect the pow er cable as close as possible to the actual battery terminals of the vehicle.
14 - 23 I/O P or t 1. Squeeze the clips next to the connector attached to the I/O cable to open the catches in the connector. 2. Firmly press the cable end (female) into the I/O Port conn ector (male) at the back of the cradle. Release the clip s in the connector cable.
14 - 24 V ehicle Cradle LED The cradle LED is lo cated at the fr ont ce nter of the vehicle cr adle. Dock ing the MX9 in a V ehicle Mounted Cradle Note: Do not put the MX9 into the vehicle cradle unti l the cradle is securely fastened to the vehicle. 1.
14 - 25 Remo ving the MX9 from t he Mounted V ehic le Cradle 1. Place one hand on the MX9 and press on e of the release latches (located on ei ther side of the cradle docking bay).
14 - 26.
15 - 1 15 T echnical Specifications MX9 Specifications MX9 Dimensions and W eight. Processor Ma r vell PXA-320 / 806 MHz Memor y 128MB on-board RAM / 128 on-board Flash Expansion slots SD expansion slot f or flash memor y (128MB / 512MB / 1GB / and 4 GB suppor ted) Inter nal CF slot for Summit a/b/g radio , protected i nside device .
15 - 2 MX9 En vironmental Specifications Main Battery T echnical Specifications Do not store MX9 batteries above 140°F (60°C) f or e xtended per iods. Wireless Radio T wo wireless radios are availab le: • Summit CF 802.11b /g (2.4GHz) • Summit CF 802.
15 - 3 Bluetooth System Compatibility Bluetooth speci fication V ersion 2 .0 + EDR . Suppor ts Bluetooth Enhanced Data Rate (EDR ) • Supports UART • Class 2 – 2.5mW (4dBm) output power • Supports the 921 kbps baud rate • Adaptive Frequency Hopping – AFH • Backward compatibility wit h Bluetooth 1.
15 - 4 Accuracy P osition to within 10 meters, 2D Root Mean Square (RMS) and 5 meters 2D RMS , Satellite Based A ugmentation System (SBAS) corrected. V elocity to within 24 meters per second.
15 - 5 Desktop Cradle T ech nical Specifications Battery Charger T ec hnical Specifications Note: Battery packs may leak up to 1mA current thro ugh the batte ry co ntacts when left in an unpowered battery charger charging pocket. Do not store MX9 batteries above 140°F (60°C) f or e xtended per iods.
15 - 6 Dimensions W eight 3 lb 10 oz / 1.6 kg (with a battery in each charging bay 2 lb 0 oz / 0.9 kg (no batteries) Length 16” / 40 cm Width 5.75” / 14.
16 - 1 16 Customer Suppor t T ech nical Assistance If you need assistance installin g or troubleshooting your de vice , please contact us by using one of the methods below: Knowledge Base: www.hsmknowledgebase.com Our Knowledge Base provides thousands of immediate solutions.
16 - 2 All provisions of this Limited W arranty are separate and se ve rab le, which means that if any provision is held inv alid and unenforceab le, such deter mination shall not affect the v alidity of enforceability of the other provisions hereof.
Back Cvr - 1.
™ Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com MX9-WM-UG Rev A 6/14.
Ein wichtiger Punkt beim Kauf des Geräts Honeywell MX9 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Honeywell MX9 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Honeywell MX9 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Honeywell MX9 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Honeywell MX9 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Honeywell MX9 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Honeywell MX9 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Honeywell MX9. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Honeywell MX9 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
