Benutzeranleitung / Produktwartung 50 des Produzenten Heat & Glo LifeStyle
Zur Seite of 52
1 Owner ’ s Manual Installation and Operation Models: RUTHERFORD-50 Wood Burning Fireplace DO NOT DISCARD THIS MANUAL NOTICE • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation.
2 Read this manual before installing or operating this fi replace. Please retain this owner ’ s manual for future reference. Homeowner Reference Information Model Name: Date purchased/installed: Se.
3 Note: An arrow ( ¨ ) found in the text signi fi es change in content. Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury .
4 Heat & Glo • RUTHERFORD-50 • 4059-333 Rev C • 06/08 W ARRANTY FOR HEA T & GLO FIREPLACES The limited warranty will not become effective until you have mailed the completed warranty card to: Hearth & Home T echnologies Inc. 20802 Kensington Blvd.
5 1 1 Listing and Code Appro v als NOTICE: This fi replace is tested and approved as a decorative fi replace. It should not be factored as a primary heat source in residential heating calculations.
6 2 2 Operat ing Instr uct ions W ARNING! DO NOT operate fi replace before reading and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . User Guide W ARNING Hot screen/mesh and glass doors will cause burns.
7 D. Grate This fi replace is designed to be used with the grate sup- plied with this unit or one approved by HHT . The grate will deteriorate over time and will need occasional replacement. W ARNING! Risk of Fire! Use only the factory-supplied integral grate.
8 W ARNING! Risk of Fire and Smoke! Fireplaces equipped with doors should be operated only with doors fully open or doors fully closed. If doors are left partly open, gas and fl ame may be drawn out of the fi replace opening. FULL Y OPEN CORRECT P ARTL Y CLOSED INCORRECT P ARTL Y OPEN INCORRECT FULL Y CLOSED CORRECT Figure 2.
9 M. Wood Fuel Hardwood vs Softwood Y our fi replace performance depends on the quality of the fi rewood you use. • Seasoned wood contains about 8,000 BTUs per pound . • Hard woods are more dense than soft woods. • Hard woods contain 60% more BTUs than soft woods.
10 3 3 Maintainance and Ser vice A. Disposal of Ashes Frequency: When they reach bottom of grate By: Homeowner B. Chimney Inspection/Cleaning Frequency: At least twice a year during heating season or as recommended by a certi fi ed chimney sweep By: Certi fi ed chimney sweep Figure 3.
11 C. Check Firebox Molded Brick Panel Frequency: After each ash removal By: Homeowner D. Inspect Grate Frequency: After each ash removal By: Homeowner Inspect grate for: • W arping or sagging 1-1/2 in.
12 4 4 T roubleshooting Guide Start Fire Problems Possible Cause Solution Can’t get fi re started Excessive smoke or spillage Burns too slowly Smolders, sizzles Not enough kindling/paper or no kindling/paper Use dry kindling, more paper . Arrange kindling & wood for air movement.
13 Additional lateral support for chimney above roof (or enclosed in chase) if needed (Section 8) Ceiling firestop on floor of attic (Section 8) Support straps on rafter supports chimney (not shown) (.
14 B. Design and Installation Considerations Draft is the pressure difference needed to vent fi replaces successfully . When a fi replace is drafting successfully , all combustion by-products are exiting the home through the chimney .
15 Marginal Location: • Below peak Location NOT recommended: • Not the highest point of the roof • Wind loading possible Multi-level Roofs Windward Leeward Recommended: Outside Air Intake on win.
16 Before beginning the installation be sure the following tools and building supplies are available: Reciprocating saw Framing material Pliers Non-combustible sealant Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits Plumb line Safety glasses Level T ape measure 1/2-3/4 in.
17 6 6 F raming & Clearances A F D B C 5/8 in. (16 mm) all configurations 1-1/2 in. min. air space from fireplace to combustible materials. 1/2 in. min. air space at nailing flanges. Note: In an exterior chase or projecting into a garage Across a corner As a room divider Along a wall 92 in.
18 B. Clearances W ARNING! Risk of Fire! Y ou must comply with all minimum air space clearances to combustibles as speci fi ed in Fig- ure 6.2. DO NOT pack required air spaces with insulation or other materials. Heat & Glo • RUTHERFORD-50 • 4059-333 Rev C • 06/08 (insulation) 0 in.
19 60-7/8 in. 50 in. 18 1/2 in. [470 mm] 19 3/4 in. [500 mm] 4 in. [102 mm] 50° angle 39° angle 24 in. [610 mm] BRICK FRONT FLUSH FRONT 24 in. [610 mm] 22 3/8 in. [568 mm] Note: Grid depicts 1 inch squares. Figure 6.3 Combustible Mantel Leg or Wall Projections (acceptable on both sides of opening) C.
20 7 7 Installation of Fireplace CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp. A. Things to Consider • Location(s) of outside air kit(s) • Gas line piping B. Position the Fireplace • Place the fi replace on a continuous fl at surface.
21 Outlet placed higher than 3 ft below the termination cap Attic space Garage or combustible liquids storage Outlet blocked by snow , leaves, etc. Clear area outside house or in ventilated crawl space YES NO NO NO NO Factory-built fireplace Figure 7.
22 Outside Air Hood 2 Wire T ies Flexible Duct (not supplied) Figure 7.5 Outside Air Installation E. Install Outside Air Kit • Keep duct runs short and straight to minimize restriction. • The outside air kits must be installed on both sides of the fi replace.
23 Figure 8.1 T ypical Chimney System - Guidelines for Chimney System Installation 8 8 Ch imney Assembly NOTICE: Chimney performance may vary . • T rees, buildings, roof lines and wind conditions affect performance. • Chimney height may need adjustment if smoking or overdraft occurs.
24 T ermination Cap Storm Collar Chase T op Flashing Chase T op Collar (4) Roof Radiation Shields Chimney Section Attic Insulation Shield & Collar Square Frame Firestop Chimney Square Frame Firestop 74 1/8 in. (1883 mm) Effective Height Figure 8.2 A.
25 A MAJOR CAUSE OF VENT RELA TED FIRES IS F AIL- URE T O MAINT AIN REQUIRED CLEARANCES (AIR SP ACES) T O COMBUSTIBLE MA TERIALS. IT IS OF THE UTMOST IMPOR T ANCE THA T DURACHIMNEY II BE INST ALLED ONL Y IN ACCORDANCE WITH THESE INSTRUCTIONS.
26 G. Assemble Chimney Sections Attach the fi rst chimney section or offset onto the top of the fi replace (Figure 8.4). Sheet metal screws are required to connect Chimney Section to Anchor Plate. Continue to add additional sections of chimney as needed.
27 I. Install Attic Insulation Shield The Attic Insulation Shield must be installed where the chimney passes into an attic. Its purpose is to prevent debris and insulation from getting too close to the chimney . In attic areas where this shield cannot fi t, or is not used you must enclose the attic portion of the chimney in a framed enclosure.
28 K. Finish T op Apply a non-hardening waterproof sealant around the chimney at the point where the Storm Collar will meet the chimney just above the fl ashing (Figure 8.14). Slide the Storm Collar down over the chimney to the top of the fl ash- ing.
29 N. Chimney T ermination Requirements • Install a cap approved and listed for this fi replace system. • Locate cap where it will not become plugged by snow or other materials. • Locate cap away from trees or other structures. • The bottom of the termination cap must be at least 3 ft (.
30 9 9 Chase Installations Ceiling Firestop Chase T op Flashing T ermination Cap False Ceiling Insulation in the outside walls of the chase Attic Insulation Shield Chimney Ceiling Firestop T abs False Ceiling False Ceiling Insulation Insulation Figure 9.
31 1/2 in. air space established by spacers Chase T op Flashing 1/2 in. Air Space (Not furnished by Dura-V ent) Fabricated Spaces Locally 1/2 Storm collar must be installed 1 in. off chase top Figure 9.4 Chase T op Construction B. Install Fireplace & Chimney Install as per Sections 7 and 8.
32 Allow a 1 in. (25 mm) air gap between storm collar and chase top flashing 1/2 in. (13 mm) air space established by spacers 1/2 in. overhang 14 in. (345 mm) diameter chimney must extend at least 6 in. (152 mm) above chase top flashing. DuraChimney II Pipe 1/2 in.
33 B. House Style Shroud • Field-fabricated spacers (1/2 in./13 mm tall, 24 ga/.024 in. galvanized steel) must be used to support the chase top fl ashing or chase pan, in order to provide air fl ow . • 14 in. (345 mm) DuraChimney II pipe must extend at least 6 in.
34 C. Arch / Mailbox Style Shroud The arch or mailbox style shroud generally has two solid sides and a solid top. The exhaust openings are on the two open ends of the arch (Figure 10.3). T able 10.2 lists the minimum shroud dimensions, the minimum open area per side, and the minimum total open area for the shroud.
35 1 1 11 Inst allation of Molded Br ick Panel A. Install Hearth Molded Brick Panel • Place hearth panel into the fi replace. C. Install Back Molded Brick Panel-T raditional • Refer to Figure 1 1.1. • Set the grate brackets in place, 26.5 in. (673 mm) center to center .
36 Figure 1 1.2 Herringbone Molded Brick Panel Note: Use T -brac ke ts as templates and dr ill pilot holes into the inner shell with the dr ill bit provided. Side panels must be installed fi rst. E. Install Back Molded Brick Panel-Herring- bone • Refer to Figure 1 1.
37 Center of Fireplace Opening Round end of Rod through rings, then into Screen Rod Clip The noncombustible finishing material across the top of the fireplace opening will be even with the lower edge of the metal face. Noncombustible finishing materials MUST overlap side faces by 1 1/4 in.
38 1 2 12 Fi ni shi n g A. Non-Combustible Materials • Materials which will not ignite and burn, composed of any combination of the following: - Steel - Iron - Brick - T ile - Concrete - Slate - Glass - Plasters • Materials reported as passing ASTM E 136, Standard T est Method for Behavior of Metals, in a V ertical T ube Furnace at 750° C B.
39 IMPORT ANT ! H ear th ex tension design must be determined before installation of fi replac e. Floor Noncombustible Framing Material Noncombustible Finishing Material Protective Metal Hearth Strips Double HX4 or equivalent & 1/2 in. Durock Bottom of fireplace opening; finished hearth surface must NOT be above it.
40 Non-combustible Sealant After completing the framing and applying the facing mate- rials over the framing, a bead of non-combustible sealant must be used to close off any gaps at the top and sides between the fi replace and hearth. Non-combustible Sealant Noncombustible Material Protective Metal Hearth Strip 30 in.
41 These surfaces may be covered with non-combustible material. Non-combustible sealant. D. Finishing Material Refer to Sections 12.A. and Sections 12.B. for combus- tible/noncombustible materials. Refer to Figure 12.10 for noncombustible zone. W ARNING! Risk of Fire! Y ou must maintain clearances.
42 E. Combustible Mantel • See Figure 12.1 1. • A combustible mantel may be positioned no lower than 22 in. (508 mm) above the top of the fi replace opening. • A combustible mantel may have a maximum depth of 12 in. (305 mm). • Combustible trim and mantels cannot be placed within 6 in.
43 F . Sidewalls/Surrounds • Adjacent combustible sidewalls must be located a minimum of 24 in. (305 mm) from the fi replace opening. • Combustible mantel legs, surrounds and stub walls may be constructed per Figure 12.12. 60-7/8 in. 50 in. 18 1/2 in.
44 A. Gas Log/Lighter Provision W ARNING! Fire and/or Asphyxiation Risk! Use with solid wood fuel or decorative gas appliance only . Gas fi re gener- ates fumes.
45 1 4 14 Reference Materials A. Fireplace Dimensions 16 1/8 in. 408 mm Gas Line Knockout 1 1 1/8 in. 282 mm 6 7/8 in. 175 mm 5 in. 129 mm 50 in. 1270 mm 60 7/8 in. 1546 mm 3 3/4 in. 97 mm 38 in. 965 mm 54 in. 1372 mm 74 1/8 in. 1883 mm 70 3/4 in. 1797 mm 16 1/8 in.
46 B. Fireplace Components 20 in. (508 mm) 66 in. (1676 mm) 1/2 in. (13 mm) HX4 Hearth Extension (3 required/shipped separately) Outside Air Kit (2 supplied) GR39 Grate (supplied) ID6 Insulated Duct UD6 Uninsulated Duct 42 in. (1067 mm) 6 in. (152.4 mm) i.
47 C. Chimney Components Catalog # Description 14DCA-12 Pipe 12 inch 14DCA-18 Pipe 18 inch 14DCA-36 Pipe 36 inch 14DCA-48 Pipe 48 inch 14 DCA-E15 15 degree Elbow 14DCA-E30 30 dectree Elbow 14DCA-ES El.
48 C. Service Parts RUTHERFORD-50 Service Parts 1 2 3 4 8 5 6 7 16 15 18 8 19 20 17 9 8 13 11 14 10 12 Heat & Glo • RUTHERFORD-50 • 4059-333 Rev C • 06/08 ¨.
49 RUTHERFORD-50 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
50 This page intentionally left blank. Heat & Glo • RUTHERFORD-50 • 4059-333 Rev C • 06/08.
51 This page intentionally left blank. Heat & Glo • RUTHERFORD-50 • 4059-333 Rev C • 06/08.
52 – NOTES – D. Contact Information DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation.
Ein wichtiger Punkt beim Kauf des Geräts Heat & Glo LifeStyle 50 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Heat & Glo LifeStyle 50 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Heat & Glo LifeStyle 50 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Heat & Glo LifeStyle 50 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Heat & Glo LifeStyle 50 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Heat & Glo LifeStyle 50 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Heat & Glo LifeStyle 50 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Heat & Glo LifeStyle 50. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Heat & Glo LifeStyle 50 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
