Benutzeranleitung / Produktwartung SL-350TRS-D des Produzenten Hearth and Home Technologies
Zur Seite of 85
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 1 Models: SL-750TRS-IPI-E SL-550TRS-IPI-E SL-350TRS-D SL-350TRS-IPI Owner ’ s Manual Installation and Operation • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 2 Congratulations Listing Label Information/Location Model Name: _________________________.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 3 Î = Contains updated information. T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 4 MODELS: SL-750TRS-IPI-E,SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Direct Vent Gas Appliance Heater STANDARD: ANSI Z21.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 5 G. Requirements for the Commonwealth of Massachusetts For all side wall horizontally ven.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 6 A. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the out- side.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 7 K C A L F I B G E D J J G A F C A H M N In addition to these framing dimensions, also reference the following sections: • Clearances and Mantel Projections (Section 3.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 8 Figure 3.2 Clearances to Combustibles C B D A Models AB C D E F G H I J DVP PIPE SL PIPE.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 9 D. Elevated Hearth Systems Use the table below to identify the hearth system that will be used. The table will also help identify ef fects on the various dimensions.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 10 E. Mantel Projections 5 6 7 8 9 10 3 4 5 12 11 10 9 8 7 6 TOP OF HOOD OR FIREPLACE OPENING 4 12 13 11 32 CEILING All measurements are in inches.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 1 1 A. V ent T ermination Minimum Clearances Fire Risk. Explosion Risk. Maintain vent clearance to combustibles as speci fi ed. • Do not pack air space with insulation or other materials.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 12 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 4.4 Minimum Clearances for T ermination A = 12 inches.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 13 Fire Hazard. Explosion Risk. Asphyxiation Risk. Do NOT connect this gas appliance to a chimney fl ue serving a separate solid-fuel or gas burning appliance.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 14 3i n .C L E A R A N C E TERMINA TION CAP FL EX -V ENT 1i n .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 15 Figure 5.4 E. V ent Diagrams 1. T op V ent - Horizontal T ermination V enting V Minimum H 1 Maximum SL-350TRS-D SL-550, SL-750TRS-E 90º Elbow 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 16 H 1 H 2 V 1 Figure 5.5 T wo Elbows V Minimum H Maximum SL-350TRS-D, SL-550TRS-E, SL-750TRS-E 90º Elbow NOT ALLOWED 1/2 ft. 152 mm 1 ft. 305 mm 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 17 Figure 5.6 1. Top Vent - Horizontal Termination - ( continued ) Three Elbows H 1 H 2 V .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 18 2. T op V ent - V ertical T ermination No Elbow V 1 = 44 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 19 Figure 5.8 T wo 90º Elbows H 1 V 1 V 2 V 1 Minimum H 1 Maximum H 1 Maximum V 2 V 1 + V 2 Minimum SL-350TRS-D SL-550TRS-E, SL-750TRS-E * * 90º Elbow 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 20 Figure 5.9 2. T op V ent - V ertical T ermination - ( continued ) Three 90º Elbows H 1 H 2 V 1 V 2 ALL MODELS V 1 H 1 + H 2 Maximum V 2 V 1 + V 2 Minimum 90º Elbow 0 0 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 21 V 1 H 1 V 3 V 2 H 2 2. T op V ent - V ertical T ermination - ( continued ) Four 90º Elbows Figure 5.17 V 1 Min. H 1 Max. V 2 Min. H 2 Max.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 22 Figure 5.12 T wo 90º Elbows 3. Rear V ent - Horizontal T ermination Figure 5.10 No Elbow H 1 = 24 in. (610 mm) Maximum 90-DEGREE ELBOWS H 1 Maximum V 1 Minimum H 2 H 1 + H 2 Maximum 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 23 3. Rear V ent - Horizontal T ermination - ( continued ) Figure 5.13 Figure 5.14 Three Elbows H 1 Maximum V 1 Minimum H 2 + H 3 H 1 + H 2 + H 3 Maximum 1-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 24 Figure 5.15 T wo Elbows H 1 Maximum V 1 Minimum H 2 H 1 + H 2 Maximum 1-1/2 ft. 457 mm Back to Back Elbows 1 ft. 305 mm 2-1/2 ft. 762 mm 3-1/2 ft.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 25 A* B* C D SL-750TRS-IPI-E Inches 41 27-7/8 40 26-7/8 Millimeters 1041 708 1016 683 SL-5.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 26 C. V ertical Penetration Framing Installing the Ceiling Firestop • Frame an opening 10 inches by 10 inches whenever the vent system penetrates a ceiling/ fl oor (see Figure 6.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 27 2 SCREWS A. T op V ent Figure 7.4 Remove the vent cap. Figure 7.5 Remove the insulation basket and white insula- tion from the center vent pipe.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 28 Figure 7.6 Remove the insulation from the outer vent pipe. Figure 7.7 T o attach the fi rst section of vent pipe, make sure to use the fi berglass gasket to seal between the fi rst vent component and the outer fi replace wrap.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 29 C. Securing and Leveling the Appliance The diagram shows how to properly position, level, and secure the appliance (see Figure 7.13). Nailing tabs are pro- vided to secure the appliance to the framing members.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 30 A. Assembly of V ent Sections (DVP Pipe) Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 31 Assembling DVP-12A Slip Sections The outer fl ue of the slip section should slide over the outer fl ue of the pipe section and into (inner fl ue) the last pipe section (see Figure 8.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 32 B. Disassembly of V ent Sections (DVP Pipe) T o disassemble any two pieces of pipe, rotate either section (see Figure 8.10), so that the seams on both pipe sections are aligned (see Figure 8.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 33 C. Installing Heat Shield and Horizontal T ermination Cap (DVP Pipe) Note: Where required, an exterior wall fl ashing is available. When penetrating a brick wall, a brick extension kit is available for framing the brick.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 34 D. Assembly of V ent Sections (SL pipe) Continue Adding V ent Components • Continue adding vent components, locking each suc- ceeding component into place.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 35 E. Installing W all Shield Firestops and Horizontal T ermination Cap (SL Pipe) NOTE: Where required, an exterior wall fl ashing is available.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 36 SCREWS CAULK STORM COLLAR (1 of 3) F . Installing Roof Flashing and V ertical T er- mination Cap T o install roof fl ashing see Figure 8.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 37 Figure 8.19 Assembling the Storm Collar Figure 8.20 Assembling the Storm Collar Around the Pipe Connect both halves of the storm collar with two screws (see Figure 8.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 38 Note: H a ve the gas supply line install ed in acco rdance w i t h l o c a l b u i l d i n g c o d e s , i f a n y . I f n o t , f o l l o w A N S I 223.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 39 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory . • Changing valve settings may result in fi re hazard or bodily injury .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 40 1 0 10 Elec tric al Information Note: This appliance must be electrically wired and gro.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 41 TRANSFORMER 3 V AC PLUG IN BLACK RED BA TTERY P ACK THERMOST A T WIRE ASSEMBL Y WIRES (TO BROWN) ORANGE GREEN VA LV E WHITE ORANGE IGNITION MODULE 3 V AC INTERMITTENT PILOT IGNITOR HOT NEUTRAL I S GROUND TO FIREPLACE CHASSIS C.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 42 TRANSFORMER 3 V AC PLUG IN PLUG IN BLACK RED BA TTERY P ACK REMOTE WIRES (TO BROWN) ORANGE GREEN VA LV E GROUND TO FIREPLACE CHASSIS WHITE ORANGE IGNITION MODULE 3 V AC INTERMITTENT PILOT IGNITOR HOT NEUTRAL I S Figure 10.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 43 E. Junction Box Installation WHT WHT BLK BLK GRN wire inside box Copper ground attached to GRN screw with GRN wire 14/2WG Cover Plate outside firebox Romex Connector Figure 10.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 44 5 6 7 8 9 10 3 4 5 12 11 10 9 8 7 6 TOP OF HOOD OR FIREPLACE OPENING 4 12 13 11 32 CEILING A.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 45 Note: There are 3 metal tabs holding the non-combustible board in place for shipping. These tabs are to be cut off or bent back before fi nishing around the appliance front.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 46 C. Splatter Guard The splatter guard is a piece of corrugated material used to protect the appliance during the installation process be- fore fi nishing work on the whole hearth is complete.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 47 Step 5. Fold bottom fl ap along score line as indicated in Figure 1 1.10 and tuck into valve access area of appli- ance. Splatter guard should fi t securely on front of unit.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 48 UNITS AND TEMPLA TE P ART # SL-350TRS-D (350-T emplate) SL-550TRS-IPI-E (550-T emplate) SL-750TRS-IPI-E (750-T emplate) DOOR FIT FINISH MA TERIAL THICKNESS SEE FIGURE XY Aero-28 Inside 4 inches Max.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 49 1 2 12 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 50 E. Install Refractory SL-550TRS-IPI-E and SL-750TRS-IPI-E only . Figure 12.7 Figure 12.6 Figure 12.8 Step 2. Place the right refractory against the fi rebox right wall such that it is against the back refractory (see Figure 12.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 51 Model: SL-350TRS-D F . Positioning the Logs CAUTION: Logs are fragile. Log #1 (SR V21 13-701) : Locate the slot on the bottom right side of log 1.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 52 Figure 6 Figure 6 Mate shoulder screw with notch Mate shoulder screw with notch Log #4 (SRV21 13-703) : Locate the notch on the bottom of log # 4.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 53 Model: SL-550TRS-IPI-E STEP 1. CAUTION: Logs are fragile! Carefully remove the logs from the packaging. 1 1 2 2 STEP 2. LOG #1 (SRV2065-704) Place log #1 on left fl at side of the burner assembly .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 54 STEP 4. LOG #3 (SRV2065-702) Place log #3 on right side of grate. The notch on the log should fi t over the bar on the far right side of the grate.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 55 Model: SL-750TRS-IPI-E STEP 1. CAUTION: Logs are fragile! Carefully remove the logs from the packaging. LOG NOTCHES STEP 2. LOG #1 (SRV2066-704) Place log #1 on left fl at side of the burner assembly .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 56 STEP 4. LOG #3 (SRV2066-702) Place log #3 on right side of grate. The notch on the log should fi t over the bar on the far right side of the grate.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 57 SL-350TRS-D SL-350TRS-IPI 3/16 in. SL-350TRS-D (LP) SL-350TRS-IPI (LP) 1/4 in. SL-550TRS-IPI-E 3/8 in. SL-550TRSIPILPE Fixed SL-750TRS-IPI-E 3/8 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 58 A. Before Lighting Appliance Before lighting this appliance determine if it has a Stand- ing Pilot or Intelli fi re ignition system by opening the con- trol access panel to view wiring system and gas valve.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 59 B. Lighting Appliance 1. T urn off all electric power to the appliance. 2. This appliance is equipped with an ignition device which automatically lights the burner .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 60 Standing Pilot Ignition 1. T urn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 61 Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 62 A. Standing Pilot Ignition System 1 4 14 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 63 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 64 B. Intelli fi re Ignition System Symptom Possible Cause Corrective Action 1. The ignitor/module makes noise, but no spark. a. Incorrect wiring.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 65 Intelli fi re Ignition System - (continued) Symptom Possible Cause Corrective Action 3. (Continued) Pilot lights but continues to spark, and main burner will not ignite.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 66 1 5 15 Maintaining and Ser vicing Appliance Although the frequency of appliance servici.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 67 Inspect Maintenance T asks Doors, Surrounds and Fronts 1. Assess condition of screen and replace as necessary . Recommend addition of screen if one is not present.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 68 1 6 16 R eference Mater ials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 69 B. V ent Components Diagrams Figure 16.2 DVP vent components 10-1/2 in. (267 mm) 10-7/8 in. (276 mm) 45 ° 7-3/8 in. (187 mm) 11-3/8 in. (289 mm) 1-1/4 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 70 B. V ent Components Diagrams ( continued ) Figure 16.3 DVP vent components T erm Cap Minimum Effective Length Maximum Effective Length T rap1 4-1/8 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 71 B. V ent Components Diagrams ( continued ) Figure 16.4 DVP vent components 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 72 DVP-TB1 BasementVent Cap 12 in. (305 mm) 1-1/2 in. (38 mm) 7-3/8 in. (187 mm) 14 in. (356 mm) 17-3/4 in. (451 mm) 10-1/2 in. (267 mm) 3-7/8 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 73 B. V ent Components Diagrams (continued) 13 in. (330 mm) 15 in. (381 mm) 8-1/8 in. (206 mm) 10-7/8 in. 276 mm 10-1/2 in. 267 mm 3° 87° Effective Length 5-3/4 to 8-3/8 in.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 74 There must be a 25% reduction in total H when using the snorkel cap except when using the simple up and out installation.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 75 SL-350TRS-D , SL-350TRS-IPI Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active 5 6 7 8 Part number list on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 76 C. Service Parts List SL-350TRS-D, SL-350TRS-IPI IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 77 SL-350TRS-D Service Parts V alve Assembly Parts List Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active 1 2 3 4 5 6 7 8 9 Standing Pilot V alve Assembly IMPORT ANT : THIS IS DA TED INFORMA TION.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 78 IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 79 SL550TRS-IPI-E Service Parts Service Parts Diagram 6 7 8 9 10 11 12 13 14 Part number list on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 80 SL-550TRS-IPI-E Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 81 SL-750TRS-IPI-E Service Parts Service Parts Diagram Beginning Manufacturing Date: June 2007 Ending Manufacturing Date: Active 10 7 8 11 12 13 14 9 6 Part number list on following page.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 82 SL-750TRS-IPI-E IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 83 IMPORT ANT : THIS IS DA TED INFORMA TION. The most current information is located on your dealers’ VIP site. When ordering, supply serial and model numbers to ensure correct service parts.
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 84 © 2005 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY HEA T & GLO GAS APPLIANCE PRODUCTS 060-981D 3/05 D. Limited Lifetime W arranty BASIC ONE-YEAR W ARRANTY .
Heat & Glo • SL-750TRS-IPI-E, SL-550TRS-IPI-E, SL-350TRS-D, SL-350TRS-IPI • 2120-900 Rev . D • 6/07 85 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com E. Contact Information Please contact your Heat & Glo dealer with any questions or concerns.
Ein wichtiger Punkt beim Kauf des Geräts Hearth and Home Technologies SL-350TRS-D (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hearth and Home Technologies SL-350TRS-D noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hearth and Home Technologies SL-350TRS-D - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hearth and Home Technologies SL-350TRS-D reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hearth and Home Technologies SL-350TRS-D erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hearth and Home Technologies SL-350TRS-D besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hearth and Home Technologies SL-350TRS-D verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hearth and Home Technologies SL-350TRS-D. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hearth and Home Technologies SL-350TRS-D gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
