Benutzeranleitung / Produktwartung HUDBAY-INS des Produzenten Hearth and Home Technologies
Zur Seite of 37
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 1 • Do not store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - Do not try to light any appliance.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 2 APPROVED FOR CANADA AND USA TO: ANSI Z21.88b-2003 / CSA 2.33b-2003 Vented Gas Fireplace Heate r , and applicab le sections o f UL307b Gas Burning Heating Appliances for Manufactured Homes and Recreat iona l V ehicles, CAN/C G A 2.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 3 T able of Contents 1 Listing and Code Approvals A. Appliance Certi fi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 B. Glass Speci fi cations . . . . . . . . . . .
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 4 Manufactured Home or Mobile Home installation may occur only after the home is site located and must conform with the Manufactured H.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 5 A. Design and Installation Considerations Quadra-Fire direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 6 Figure 3.1 Model A B C D Hudson Bay Insert Inches 14 1 1 12 7 Millimeters 356 279 305 178 B. Clearances to Combustibles 3 3 F raming and Clearances Note: • Illustrations reflect typical installations and are FOR DESIGN PURPOSES ONL Y .
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 7 Fire Risk. Asphyxiation Risk. • T erminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. V ent T ermination Minimum Clearances Figure 4.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 8 TERMINA TION CAP ADAPTER FLEX PIPE TRANSITION ASSEMBL Y SHIPPING BRACKETS A TTACHED TO REAR OF APPLIANCE FOR USE AS LEVELING LEGS A.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 9 INSULA TION V=10 FT . (3 M) MINIMUM 40 FT . (12 M) MAXIMUM TERMINA TION CAP ADAPTOR INLET AIR VENT PIPE EXHAUST AIR VENT PIPE Figure 5.3 Note: Insulation is not included with the venting kit.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 10 Figure 6.2 Kit contents: Replacement ori fi ce; replacement pilot injector; valve regulator; conversion label. T ools required: Ratchet with 7/16 in. (1 1 mm) socket and 2 in. - 4 in.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 1 1 Figure 6.5 Figure 6.6 Figure 6.7 A B C Figure 6.8 C. V alve Regulator Replacement Remove upper and lower back shield. Loosen the set col- lars on the extension rods with the 3/32 in.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 12 Ensure that the rubber gasket (D) is properly positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied with the kit. T ighten screws securely .
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 13 Leak test all gas line joints and the gas control valve prior to and after starting the appliance. Before making the gas connection, ensure that the appliance you are installing is designed for the type of gas being supplied.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 14 C. Standing Pilot Ignition System Wiring This appliance DOES NOT require 1 10 V AC supply for operation. A wiring diagram is shown in Figure 7.2 on the next page. This appliance is equipped with a millivolt control valve.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 15 Figure 7.2 ROCKER SWITCH / W ALL THERMOST A T / REMOTE V ARIABLE REGULA TOR PILOT ADJUSTMENT CAP MANIFOLD PRESSURE INLET PRESSURE PUSH BUTTON IGNIT OR THERMOPILE IGNITOR PILOT THERMOCOUPLE CAUTION Label all wires prior to disconnection when servicing controls.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 16 C. Door Crown Installation Open lower access panel. Pull out and unhook the two spring latches on the bottom of the appliance that secure the door. Rotate the door forward approximately 1-1/2 in.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 17 D. Grille Installation Remove the door of appliance. Remove the four screws (two at each end) holding grille in place. Lift up to remove. Figure 8.5 Determine your desired placement of the rocker switch.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 18 F . Brick Installation The pilot shield has to be removed to install or remove the brick refractory . Removal of the bracket requires remov- ing two screws. Figure 8.10 Figure 8.1 1 Figure 8.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 19 G. Positioning the Logs While still breakable, the logs do not become fragile until after the appliance is burned and they have cured. After curing, any handling must be done with care as breakage can easily occur .
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 20 H. Mineral W ool I. Blower Installation Included in kit: Blower . T ools required: Powered Phillips head screwdriver . Figure 8.23 Figure 8.24 Figure 8.25 Figure 8.21 I nstall the left twig (#6) over the locator pins in the right rear log and the left front log.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 21 Figure 8.26 Figure 8.27 Installation is the reverse of removal. Figure 8.28 Blower Wiring Diagram F = 1/4 in. (6 mm) female spade M = 1/4 in. (6 mm) male spade Disconnect wires from the blower.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 22 Figure 8.29 J. Air Shutter Adjustment The air shutter is used to fine-tune the flame as necessary. The air shutter is shipped in the fully open position. Allow the unit to operate 15-20 minutes before making any adjustments to the air shutter.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 23 A. Before Lighting Appliance Read this entire manual prior to using the appliance.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 24 B. Lighting Appliance 1. Set the thermostat to lowest setting. 2. T urn off all electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "OFF" position.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 25 Initial Break-in Procedure When you light the appliance, you may notice that it pro- duces heat which does have an associated odor or smell.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 26 A. Standing Pilot Ignition System 1 0 10 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 27 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. Continued c. Defective valve. T urn the valve knob to the ON position. Place the ON/OFF switch in the ON position.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 28 A. Glass Replacement Glass can be replaced either as three separate pieces, or as an assembly with the door. See Service Parts List. T o Replace Separate Glass Pieces • Turn of f gas to the appliance.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 29 Inspect Maintenance T asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to air fl ow . 3. V erify maintenance of proper clearance to combustible household objects.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 30 MINIMUM FIREBOX OPENING Height: Width: Depth: Front Rear Front Rear T op Bottom Inches 20-1/4 14-1/2 26-1/2 20 13 13 Millimeters 51.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 31 B. V ent Components List V enting System Components Description HHT Component # LINK-DV4-30B Includes one piece 3 in. x 30 ft. Flex; one piece 3 in. x 4 ft. Flex; Cap/Adapter Linear to Coaxial with Flashing.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 32 R Service Parts Diagram Hudson Bay Insert HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ Service Parts Part number list on following page.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 33 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer .
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 34 R V alve Assembly Diagram Hudson Bay Insert HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 35 D. Limited Lifetime W arranty Hearth & Home T echnologies LIMITED W ARRANTY Hearth & Home T echnologies (“HHT”) and its.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 36 D. Limited Lifetime W arranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials.
Quadra-Fire • Hudson Bay Insert • 7008-1 15 Rev . H • 10/08 37 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .quadra fi re.com E. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns.
Ein wichtiger Punkt beim Kauf des Geräts Hearth and Home Technologies HUDBAY-INS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hearth and Home Technologies HUDBAY-INS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hearth and Home Technologies HUDBAY-INS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hearth and Home Technologies HUDBAY-INS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hearth and Home Technologies HUDBAY-INS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hearth and Home Technologies HUDBAY-INS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hearth and Home Technologies HUDBAY-INS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hearth and Home Technologies HUDBAY-INS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hearth and Home Technologies HUDBAY-INS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
